PB-1408-1 Spec Sheet

SPECIFICATION
FOR
APPROVAL
Customer:
Description: Piezo Audio Transducer
Sob erton Part No. : PB-1408-1
Date:2007-03-31
Customer Model No. :
Date of Approval
Authorization
Signature
211 N. First Street
Minneapolis, MN. 55401
612-849-6205
Http://www.sob erton.com E-mail: info@sob erton.com
Approved
Checked
Issue
Wang Xue Wen
Shi Cong
Tang Yu Jing
2007/03/31
2007/03/31
2007/03/31
Item
Model No.
SPECIFICATIONS
PB-1408-1
Page
1/6
1. ELECTRICAL AND ACOUSTICAL SPECIFICATION
1-1
Rated Voltage
V
12
1-2
Operating Voltage
V
3-16
1-3
*Rated Current(Max)
mA
7
1-4
*Min Sound Output at 10cm
dB
80
1-5
*Resonant Frequency
Hz
4000±500
1-6
Tone Nature
1-7
Operating Temperature
℃
-20~+70
1-8
Storage Temperature
℃
-30~+80
1-9
Weight
g
1
1-10
Housing Material
Noryl (Black)
1-11
Lead Pin Material
Red Copper
Single
*Value Applying at Rated Voltage(DC)(resonant frequency,1/2 duty,square wave)
Issue No
Description
Unit
03/31/07
Tang Yu Jing
Shi Cong
Wang Xue Wen
Date
Issue
Check
Approval
Specifications
Page
Model No.
SPECIFICATIONS
PB-1408-1
ENVIRONMENTAL TEST
Item
Specifications
2-1
Storage in High temp.
Storage in +80℃±2℃ test box for 240 hours,then expose to the room
temperature for 2 hours without applying power.
2-2
Storage in Lower temp.
Storage in -30℃±2℃ test box for 240 hours,then expose to the room
temperature for 2 hours without applying power.
2-3
Storage in Humidity
Storage in +40℃±2℃ 90-95%RH test box for 96 hours, then expose to the
room temperature for 2 hours without applying power.
+80℃
- 30℃
2-4
+20℃
+20℃
Thermal cycle test.
Make this test for 5 cycles without applying power, then expose to the room
temperature for 2 hours.
2-5
Vibration test
Make this test for the directions of X,Y, Z for 2 hours each (total 6 hours).
Free drop a unit from the height 100cm to the surface of 10mm thick
board ,three directions(X,Y,Z).
2-6
Drop test
2-7
Solderability
test
Soldering temp.:260±5℃
Heat applying time: 3±0.5sec.
PASS CRITERION :
After these tests , the change of S.P.L shall be within ±5 dB .
Issue No
Description
2/6
03/31/07
Tang Yu Jing
Shi Cong
Wang Xue Wen
Date
Issue
Check
Approval
Page
SPECIFICATIONS
Model No.
PB-1408-1
3.MEASURING METHOD(BUZZER MODE)
3-1 .Test Condition
3-1-1.STANDARD
Temperature : 25±3℃
Relative humidity : 60% ~ 70%,
Atmospheric pressure : 860mbar to 1060mbar
3-1-2.JUDGEMENT
Temperature : 15 ~ 35℃
Relative humidity : 45% ~ 85%,
Atmospheric pressure : 860mbar to 1060mbar.
3-2 . Standard Test Fixture
1.rated Voltage(Square wave): 12V
2.Resonant Frequency:
4000Hz±500
DC power
Issue No
Description
3/6
Current meter
03/31/07
Tang Yu Jing
Shi Cong
Wang Xue Wen
Date
Issue
Check
Approval
Page
SPECIFICATIONS
Model No.
PB-1408-1
4. WAVE SOLDER CURVE
(
)
* Wave Soldering profile of lead-free
Temp.(° C)
Max. 10 sec.
250° C
245° C
235° C
200K/s--130° C
---5K/s
100° C
---forced cooling
50°C
0
0
50
100
150
200
250
300
Time(sec)
Recommendable wave soldering condition is as follows.
Note 1: It is requested that wave soldering should be executed after
heat of product goes down to normal temperature.
Note 2: Peak wave temperature of 235° C ~ 250° C maximum of 10 sec. .
Issue No
Description
4/6
03/31/07
Tang Yu Jing
Shi Cong
Wang Xue Wen
Date
Issue
Check
Approval
Page
Model No.
SPECIFICATIONS
PB-1408-1
5.DIMENSIONS
Unless otherwise specified, Tolerance:±0.5(Unit: mm)
6
Lead pin
5
Epoxy
4
Masking
label
2
Red
Copper
Resin
1
Paper
3
Housing
1
Black
Noryl
2
Piezo element
1
Nickel
1
PCB
1
Epoxy Board
Part No.
Part Name
Q’TY
Material
Remark
1: All parts must be meet to ROHS.
2: Wave solder allowed,wash not allowed.
Issue No
Description
5/6
03/31/07
Tang Yu Jing
Shi Cong
Wang Xue Wen
Date
Issue
Check
Approval
Page
Model No.
SPECIFICATIONS
PB-1408-1
6.PACKING
adhesive tape
adhesive tape
Issue No
Description
6/6
03/31/07
Tang Yu Jing
Shi Cong
Wang Xue Wen
Date
Issue
Check
Approval