Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series “L” Features: • • • • • “T” 0.125” (3.175 mm) slot width Choice of aperture (0.050” or 0.010” width) Choice of opaque or IR transmissive shell material Choice of mounting configurations Choice of lead spacing or wires “N” Product Photo Here “P” Description: Each device in this series provides the flexibility of a custom device from a standard product line. Building from a standard housing with a 0.125” (3.18 mm) wide slot, a user can choose aperture width, opaque or IR transmissive housing shell material, PCBoard lead spacing or wires and mounting tab configuration. Housings are made from an opaque grade of injection-molded plastic to minimize sensitivity to both visible and near-infrared light. Discrete shells exposed on the parallel faces inside each device’s throat are made from either IR transmissive plastic (for applications where dust protection is needed) or from opaque plastic with aperture openings (for applications that require maximum protection against ambient light). Phototransistor sensor devices include the OPB859, OPB360, OPB370, OPB380, OPB390, OPB860 and OPB870, while the OPB355 provides a photodiode sensor. The photodiode sensor has a lower and more linear output-versus-light input than the phototransistor models. The OPB355, OPB360, OPB370, OPB859, OPB860 and OPB870 are designed for direct connection to through hole PCBoards. The OPB380, OPB390, OPB880 and OPB890 have 26 AWG, UL approved wires connected directly to the device for remote sensing applications. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. OPB360, OPB370, OPB380, OPB390 OPB859 OPB860, OPB870, OPB880, OPB890 Applications: • • • • • OPB355 Non-contact object sensing Assembly line automation 1 3 2 4 Machine automation 1 3 2 4 Equipment safety Machine safety Wire Colors Color # RoHS Description 1 Red 2 Black CONTAINS POLYSULFONE 3 4 White Green To avoid stress cracking, we suggest using ND Industries’ Vibra-Tite for thread-locking. Vibra-Tite evaporates fast without causing structural failure in OPTEK’s molded plastics. Applies to: OPB360, OPB370, OPB380, OPB390 and OPB860, OPB870, OPB880, OPB890. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.8 5/09 Page 1 of 10 Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series Part Number Guide — OPB355 OPB 3 X X X Optek Assembly Mounting Configurations: N — No mounting tabs L — Emitter side mounting tab only P — Sensor side mounting tab only T — Two mounting tabs Photodiode Output Family Part Number Guide — OPB360 / OPB370 OPB 3 X X X X X Optek Assembly Sensor Aperture: 1 — 0.010” (0.254 mm) 5 — 0.050” (1.270 mm) Phototransistor Output Family Emitter Aperture: 1 — 0.010” (0.254 mm) 5 — 0.050” (1.270 mm) Discrete Shell Material: 6 — Base mount IR transmissive Polysulfone discrete shell PCMountable leads 7 — Base mount opaque Plastic discrete shell PCMountable leads Mounting Configurations: L — Emitter side mounting tab only N — No mounting tabs P — Sensor side mounting tab only T — Two mounting tabs Lead Spacer Designator: 0 = 0.320” (8.12 mm) lead space 5 = 0.220” (5.59 mm) lead space Part Number Guide — OPB380 / OPB390 OPB 3 X 0 X X X Z Optek Assembly RoHS Compliant Phototransistor Output Family Sensor Aperture: 1 — 0.010” (0.254 mm) 5 — 0.050” (1.270 mm) Discrete Shell Material: 8 — Base mount IR transmissive Polysulfone discrete shell PCMountable leads 9 — Base mount opaque plastic discrete shell PCMountable leads Emitter Aperture: 1 — 0.010” (0.254 mm) 5 — 0.050” (1.270 mm) Mounting Configurations: L — Emitter side mounting tab only N — No mounting tabs P — Sensor side mounting tab only T — Two mounting tabs OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.8 5/09 Page 2 of 10 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series Part Number Guide — OPB859 OPB 8 5 9 Optek Assembly Emitter Aperture: 0.050” (1.270 mm) Sensor Aperture: 0.050” (1.270 mm) Mounting Configuration: T — Two mounting tabs Phototransistor Output Family Part Number Guide — OPB860 / OPB870 OPB 8 X X X X X Optek Assembly Sensor Aperture: 1 — 0.010” (0.254 mm) 5 — 0.050” (1.270 mm) Phototransistor Output Family Emitter Aperture: 1 — 0.010” (0.254 mm) 5 — 0.050” (1.270 mm) Discrete Shell Material: 6 — Base mount IR transmissive Plastic discrete shell PCMountable leads 7 — Base mount opaque Plastic discrete shell PCMountable leads Electrical Specification Variations: 0 = Electrical Parameter A (lead spacing = 0.320”) 1 = Electrical Parameter B (lead spacing = 0.320”) 2 = Electrical Parameter C (lead spacing = 0.320”) 5 = Electrical Parameter A (lead spacing = 0.220”) 6 = Electrical Parameter B (lead spacing = 0.220”) 7 = Electrical Parameter C (lead spacing = 0.220”) Mounting Configurations: N — No mounting tabs L — Emitter side mounting tab only T — Two mounting tabs P — Phototransistor side mounting side Note: Assemblies with dual 0.010” apertures are currently available with electrical parameter “A” only. Part Number Guide — OPB880 / OPB890 OPB 8 X X X X X Z Optek Assembly RoHS Compliant Phototransistor Output Family Sensor Aperture: 1 — 0.010” (0.254 mm) 5 — 0.050” (1.270 mm) Discrete Shell Material: 8 — Base mount IR transmissive Plastic discrete shell 9 — Base mount opaque Plastic discrete shell Emitter Aperture: 1 — 0.010” (0.254 mm) 5 — 0.050” (1.270 mm) Electrical Specification Variations: 0 = Electrical Parameter A 1 = Electrical Parameter B 2 = Electrical Parameter C Note: Assemblies with dual 0.010” apertures are currently available with electrical parameter “A” only. Wires = 26AWG—24” Long, UL approved Mounting configurations: L — Emitter side mounting tab only N — No mounting tabs P — Phototransistor side mounting side T — Two mounting tabs OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.8 5/09 Page 3 of 10 Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series OPB355, OPB360, OPB370, OPB860, OPB870 E / Clear Top Denotes LED OPB380, OPB390 S / Black Top Denotes Sensor OPB880, OPB890 OPB859 Pin # Emitter Pin # Transistor/Diode 1 Anode 3 Collector / Anode 2 Cathode 4 Emitter / Cathode [ MILLIMETERS] DIMENSIONS ARE IN: INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.8 5/09 Page 4 of 10 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage Temperature(1) (2) OPB355, OPB360, OPB370, OPB859, OPB860, OPB870 Series OPB380, OPB390, OPB880, OPB890 Series Operating Temperature(1) (2) Lead Soldering Temperature -40° C to +100° C -40° C to +85° C -40° C to +85° C (7) 260° C Input LED Forward DC Current OPB355, OPB360, OPB370, OPB380, OPB390, OPB859, OPB860, OPB870, OPB880, OPB890 50 mA Peak Forward Current (1µs pulse width, 300 pps) 1A Reverse DC Voltage 2V Power Dissipation (2) 75 mW Output Phototransistor/Diode Cathode-Anode Reverse Voltage -OPB355 60 V Collector-Emitter Voltage OPB360, OPB370, OPB380, OPB390, OPB859, OPB860, OPB870, OPB880, OPB890 Series 30 V Emitter-Collector Voltage Collector DC Current Power Dissipation (1) 5V 30 mA 100 mW Notes: (1) For wire series (OPB380, OPB390, OPB880 and OPB890), maximum storage and operating temperature is limited by the temperature rating of the lead wires. (2) Derate linearly 1.67 mW/° C above 25° C. (3) For OPB355, OPB360 and OPB370, polarity is denoted by color of housing top: LED (clear); sensor (black). (4) Cleaning agents methanol and isopropanol are recommended. Spray or wipe; do not submerge. (5) OPB380 and OPB390 wire terminations have 24” of 7-strand 26 AWG UL approved insulated wire on each terminal. These devices incorporate a wire strain relief at the housing surface. The insulation colors and functions are: IRED anode (red); IRED cathode (black); phototransistor collector (white); phototransistor emitter (green). (6) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (7) All parameters were tested using pulse technique. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.8 5/09 Page 5 of 10 Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Transistor/Diode (See OP240 for additional information—for reference only) VF Forward Voltage - 1.3 1.8 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2 V Output Diode — OPB355 (See OPB950 for additional information — for reference only) VBR Reverse Diode Breakdown Voltage 60 - - V IR = 100 µA, IF = 0, EE = 0 VFD Forward Voltage Photodiode - - 1.2 V IF = 1 mA, IF = 0, EE = 0 ID Reverse Dark Current - - 60 nA VR = 30 V, EE = 0, IF = 0 Output Transistor (See OP550 for additional information—for reference only) V(BR)CEO Collector-Emitter Breakdown Voltage 30 - - V IC = 1 mA V(BR)ECO Emitter-Collector Breakdown Voltage 5 - - V IE = 100 µA Collector-Emitter Dark Current - - 100 nA VCE = 10 V, IF = 0, EE = 0 10 - 200 µa VR = 5 V, IF = 40 mA Collector-Emitter Saturation Voltage OPB859 OPB860/870/865/875 (Para. A) OPB861/871/866/876 (Para. B) OPB862/872/867/877 (Para. C) OPB880/890/ (Para. A) OPB881/891 (Para. B) OPB882/892 (Para. C) - - 0.4 0.4 0.4 0.6 0.4 0.4 0.6 V IC = 125 µA, IF = 20 mA IC = 400 µA, IF = 20 mA IC = 800 µA, IF = 20 mA IC = 1800 µA, IF = 20 mA IC = 400 µA, IF = 20 mA IC = 800 µA, IF = 10 mA IC = 1800 µA, IF = 20 mA On-State Collector Current OPB36X, OPB37X (T, N, L, P 11) OPB36X, OPB37X (T, N, L, P 51) OPB36X, OPB37X (T, N, L, P 55) OPB38X, OPB39X (T, N, L, P 11) OPB38X, OPB39X (T, N, L, P 51) OPB38X, OPB39X (T, N, L, P 55) 1.0 2.5 3.5 1.0 2.5 3.5 - 5 10 14 5 10 14 mA VCE = 0.4 V, IF = 20 mA OPB859 250 - - µA VCE = 10 V, IF = 20 mA OPB860/870/865/875 (Para. A) OPB861/871/866/876 (Para. B) OPB862/872/867/877 (Para. C) OPB880/890/ (Para. A) OPB881/891 (Para. B) OPB882/892 (Para. C 0.5 1.0 1.8 0.5 1.0 1.8 - - ICEO Coupled IL VCE(SAT) IC(ON) On-State Collector Current OPB355 (L, N, P, T) mA VCE = 10 V, IF = 20 mA VCE = 5 V, IF = 10 mA VCE = 0.6 V, IF = 20 mA VCE = 10 V, IF = 20 mA VCE = 5 V, IF = 10 mA VCE = 0.6 V, IF = 20 mA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.8 5/09 Page 6 of 10 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series OPB355 - Flag Next to Emitter OPB355 - Flag Next to Sensor 1.20 1.20 Top to Bottom Top to Bottom 1.00 Typical IC (ON) Response (mA) Typical IC (ON) Response (mA) 1.00 0.80 Right to Left Left to Right 0.60 0.40 Left to Right Right to Left 0.60 0.40 0.20 0.20 0.00 0.00 0.80 0.05 0.10 0.15 0.20 0.25 0.00 0.00 0.05 Displacement Distance (inches) 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPB355 - Flag in Middle of Slot 1.20 Top to Bottom Typical IC (ON) Response (mA) 1.00 0 Top to Bottom 0.80 Right to Left Left to Right 0.60 Emitter Left to Right Right to Left 0.40 Sensor 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.8 5/09 Page 7 of 10 Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series Aperture Configuration 11 Next - FlagtoNext to Emitter OPB370T11 - Flag Emitter Aperture Configuration 11Next - FlagtoNext to Sensor OPB370T11 - Flag Sensor 1.20 1.20 Top to Bottom Top to Bottom 1.00 Typical IC(ON) Response (mA) Typical IC(ON) Response (mA) 1.00 0.80 0.80 Left to Right Right to Left Right to Left Left to Right 0.60 0.60 0.40 0.40 0.20 0.20 0.00 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) Displacement Distance (inches) Aperture Configuration Flag inof Middle OPB370T11 - Flag11 in- Middle Slot of Slot 1.20 Top to Bottom Typical IC(ON) Response (mA) 1.00 0 Top to Bottom 0.80 Right to Left Left to Right 0.60 Emitter Left to Right Right to Left 0.40 Sensor 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Diisplacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.8 5/09 Page 8 of 10 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series Aperture Configuration Flag Next Emitter OPB370N51 - Flag51in- Middle of to Slot Aperture Configuration 51Next - FlagtoNext to Sensor OPB370N51 - Flag Sensor 1.20 1.20 Top to Bottom Top to Bottom 1.00 Typical IC(ON) Response (mA) Typical IC(ON) Response (mA) 1.00 0.80 Left to Right Right to Left 0.60 0.40 0.20 Left to Right Right to Left 0.60 0.40 0.20 0.00 0.00 0.80 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.05 Displacement Distance (inches) 0.10 0.15 0.20 0.25 Displacement Distance (inches) Aperture Configuration 51 in - Flag in Middle OPB370N51 - Flag Middle of Slotof Slot 1.20 Top to Bottom Typical IC(ON) Response (mA) 1.00 0 Top to Bottom 0.80 Left to Right Right to Left 0.60 Emitter Left to Right Right to Left 0.40 Sensor 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.8 5/09 Page 9 of 10 Slotted Optical Switch OPB355, OPB360, OPB370, OPB380, OPB390 OPB859, OPB860, OPB870, OPB880, OPB890 Series ApertureOPB380T55 Configuration 55 -Next FlagtoNext to Emitter - Flag Emitter Aperture Configuration 55Next - Flag to Sensor OPB380T55 - Flag toNext Sensor 1.20 1.20 Top to Bottom Top to Bottom 1.00 Typical IC(ON) Response (mA) Typical IC(ON) Response (mA) 1.00 0.80 Right to Left Left to Right 0.60 0.40 0.20 0.80 Right to Left Left to Right 0.60 0.40 0.20 0.00 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.05 Displacement Distance (inches) 0.10 0.15 0.20 0.25 Displacement Distance (inches) Aperture Configuration Flag in of Middle OPB380T55 - Flag55in- Middle Slot of Slot 1.20 Top to Bottom Typical IC(ON) Response (mA) 1.00 0 Top to Bottom 0.80 Right to Left Left to Right 0.60 Emitter Left to Right Right to Left 0.40 Sensor 0 0.20 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.8 5/09 Page 10 of 10 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com