Slotted Optical Switch OPB825, OPB825A, OPB825B Features: • • • • Non-contact switching Fast switching speed 0.160” (4.06 mm) wide slot 0.300” (7.62 mm) lead spacing Product Photo Here Description: Each OPB825, OPB825A and OPB825B consists of an infrared emitting diode and a NPN silicon phototransistor mounted in a low-cost black plastic housing on opposite sides of a 0.160” (4.064 mm) wide slot. OPB825 has no mounting tabs and is intended for direct insertion into PCBoards or dual-in-line sockets. OPB825A has one mounting tab on the phototransistor side, while OPB825B has mounting tabs on both sides (two tabs). Phototransistor switching takes place whenever an opaque object passes through the slot. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: • • • • • Non-contact interruptive object sensing Assembly line automation Machine automation Equipment security Machine safety Ordering Information Part Number Description OPB825 Slotted Switch (no tabs) OPB825A Slotted Switch (one tab) OPB825B Slotted Switch (two tabs) Pin # Description Pin # Description 1 Anode 3 Collector 2 Cathode 4 Emitter RoHS 1 3 2 4 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.1 12/05 Page 1 of 3 Slotted Optical Switch OPB825, OPB825A, OPB825B Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage & Operating Temperature Range -40°C to +85° C (1) Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] 260° C Input Diode Forward DC Current 50 mA Peak Forward Current (1 µs pulse width, 300 pps) 3A Reverse DC Voltage 2V Power Dissipation (2) 100 mW Output Phototransistor Collector-Emitter Voltage 30 V Emitter-Collector Voltage 5V Collector DC Current Power Dissipation 30 mA (2) 100 mW Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (See OP240 for additional information) VF Forward Voltage - - 1.6 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2 V Output Phototransistor (See OP550 for additional information) V(BR)CEO Collector-Emitter Breakdown Voltage 30 - - V IC = 1 mA V(BR)ECO Emitter-Collector Breakdown Voltage 5 - - V IE = 100 µA Collector Dark Current - - 100 nA VCE = 10 V, IF = 0, EE = 0 VCE(SAT) Collector-Emitter Saturation - - 0.4 V IC = 250 µA, IF = 20 mA IC(ON) On-State Collector Current 1.0 - 45.0 mA IF = 20 mA, VCE = 10 V ICEO Combined Notes: (1) (2) (3) (4) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.67 mW/°C above 25 ° C. All parameters tested using pulse techniques. Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and ketones. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A .1 12/05 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Slotted Optical Switch OPB825, OPB825A, OPB825B OPB825 - Flag Next to Sensor 1.20 1.00 1.00 Typical I C(ON) Response (mA) Typical I C(ON) Response (mA) OPB825 - Flag Next to Emitter 1.20 0.80 0.60 Right to Left Left to Right Top to Bottom 0.40 0.20 0.00 0.00 0.80 0.60 Right to Left Left to Right Top to Bottom 0.40 0.20 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPB825 - Flag Next to Emitter Test Schematic 1.20 Typical I C(ON) Response (mA) 1.00 0.80 0.60 Right to Left Left to Right Top to Bottom 0.40 0.20 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.1 12/05 Page 3 of 3