Photologic Sensor OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Features: Choice of four output options in low-cost side-looking package Choice of two sensitivity options (OPL560/561/562/563) High noise immunity Direct TTL/LSTTL CMOS interface Data rates to 250 kBaud for all except OPL560 series (200 kBaud) Low power consumption Product Photo Here Description: All components in this series include a photodiode, amplifier, voltage regulator, Schmitt trigger and NPN output transistor on a single silicon chip. OPL560 chips also include a voltage regulator on the chip. All devices in the series have a Photologic® chip that is encapsulated in a molded plastic side-looking package with an integral lens (recessed integral lens for OPL535 and OPL536). This packaging provides enhanced optical coupling, combined with mechanical protection. The hysteresis characteristics of the Schmitt trigger on each device offers high immunity to noise on input and VCC. OPL530, OPL531, OPL535 and OPL536 include a 10 K Ω pull-up resistor (RL) from output to VCC. These components exhibit very stable performance over supply voltages ranging from 4.5 V to 16 V and a wide range of irradiance levels. OPL550 and OPL551 devices feature TTL/LSTTL compatible logic level output which can drive up to 8 TTL loads without additional circuitry and medium-speed data rates to 250 kBaud, with typical rise and fall times of 25 nanoseconds. OPL560, OPL561, OPL562 and OPL563 devices feature TTL/LSTTL compatible logic level output which can drive up to 10 TTL loads over supply voltages ranging from 4.5 V to 16 V. OPL530, OPL531, OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 are mechanically and spectrally matched to OP140 and OP240 LEDs. OPL535 and OPL536 are mechanically and spectrally matched to OP145 and OP245 series LEDs. Applications: Non-contact reflective object sensor Assembly line automation Machine automation Machine safety End of travel sensor Door sensor Base Part Number Package Output Type - with Light OPL530 External Lens Internal 10K - High Recessed Lens Internal 10K - High OPL531 OPL535 OPL536 Internal 10K - Low Input Power Range (mW/cm2) [Min/Max] - A B 0.08/0.40 0.08/0.25 0.20/0.40 Internal 10K - Low OPL550 Totem Pole - High 0.25/2.4 0.25/1.4 OPL551 Totem Pole - Low 0.25/2.5 0.25/1.5 0.09/0.55 0.09/0.36 0.025/0.23 0.025/0.14 0.07/0.23 OPL560 OPL561 External Lens Totem Pole - High Totem Pole - Low OPL562 Totem Pole - High OPL563 Totem Pole - Low N/A 0.18/0.55 OC = Open Collector Output RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue B 10/14 Page 1 of 8 Photologic Sensor OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 OPL530, OPL550, OPL560 Series DIMENSIONS ARE IN: Pin # Sensor 1 Ground 2 Output 3 VCC [ MILLIMETERS] INCHES OPL535, OPL536 Series DIMENSIONS ARE IN: Pin # Sensor 1 Ground 2 Output 3 VCC [ MILLIMETERS] INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 10/14 Page 2 of 8 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Photologic Sensor OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 (-OC, -OCA, -OCB) OPL550, OPL550A, OPL551, OPL551A, OPL560, OPL560A, OPL561, OPL561A, OPL562, OPL562A, OPL563, OPL563A OPL550/550A/560/560A/562/562A Totem-Pole OPL530/535/550/560/562 (-OC, -OCA, -OCB) Open-Collector VCC VCC OUT OUT GND OPL 551/551A/561/561A/563/563A/ Inverted Totem-Pole GND OPL 531/536/551/561/563 (-OC, -OCA, -OCB) Inverted Open-Collector VCC VCC OUT OUT GND GND OPL530, OPL530A, OPL530B, OPL531, OPL531A, OPL531B OPL535, OPL535A, OPL535B, OPL536, OPL536A, OPL536B OPL530/530A/530B, OPL535/535A/535B 10K Pull-Up OPL531/531A/531B, OPL536/536A/536B Inverted 10K Pull-Up VCC VCC OUT OUT GND GND VCC VCC OUT OUT GND GND OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue B 10/14 Page 3 of 8 Photologic Sensor OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Absolute Maximum Ratings (TA=25°C unless otherwise noted) Input Diode Supply Voltage (VCC) OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536, OPL536-OC, OPL550, OPL551 OPL560, OPL561, OPL562, OPL563 Operating Temperature Range 18 V 10 V 18 V -40° C to + 85° C Storage Temperature Range -40° C to + 100° C Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] 260°C Sourcing Current OPL560, OPL561, OPL562, OPL563 10 mA Power Dissipation OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536, OPL536-OC OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 90 mW 200 mW(2) Sinking Current OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536, OPL536-OC OPL550, OPL551 OPL560, OPL561, OPL562, OPL563 50 mA 50 mA Voltage at Output Lead (4) OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536, OPL536-OC OPL550-OC, OPL551-OC OPL560-OC, OPL561-OC, OPL562-OC, OPL563-OC 35 V 35 V 35 V Duration of Output Short to VCC or Ground OP550, OP551 1 second Duration of Output Short to VCC OPL550-OC, OPL551-OC OPL560, OPL561, OPL562, OPL563, OPL560-OC, OPL561-OC, OPL562-OC, OPL563-OC 1 second 1 second Low Level Output Current OPL550, OPL551 Series 16 mA High Level Output Current OPL550, OPL551 Series 1 mA Irradiance OPL550, OPL551 Series OPL560, OPL560-OC, OPL561, OPL561-OC OPL562, OPL562-OC, OPL563, OPL563-OC 10 mW/cm2 9 mW/cm 3 mW/cm2 Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 10/14 Page 4 of 8 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Photologic Sensor OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Operating Supply Voltage VCC OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC, OPL560, OPL561 Series 4.5 - 16 V - OPL550, OPL551 Series 4.5 - 5.5 V - - - 2 V f = DC to 50 MHz - 2 - V VCC = 5 V DC, f = DC to 50 MHz OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC - 2.7 5 mA EE = 0 or 1 mW/cm2 OPL550, OPL551 Series - 8 15 mA EE = 0 or 3 mW/cm2, VCC = 5.5 V OPL560, OPL561 Series - 8 12 mA EE = 0 or 1 mW/cm2 OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC 0.08 - 0.40 mW/cm2 TA = 25° C OPL530A, OPL530-OCA, OPL531A, OPL531-OCA OPL535A, OPL535-OCA, OPL536A, OPL536-OCA 0.08 - 0.25 mW/cm2 TA = 25° C OPL530B, OPL530-OCB, OPL531B, OPL531-OCB OPL535B, OPL535-OCB, OPL536B, OPL536-OCB 0.12 - 0.40 mW/cm2 TA = 25° C .25 .25 - 2.4 1.4 mW/cm2 VCC = 5 V, TA = 25° C mW/cm2 VCC = 5 V, TA = 25° C OP530, OP531 Series 1.05 1.3 1.6 - - OP535, OP536 Series 1.05 1.2 1.5 - - OPL550, OPL551 Series 1.50 2 2.5 - - OPL560, OPL561 Series 1.20 1.55 2 - - Peak-to-Peak VCC Ripple Necessary to Cause False Triggering of Output OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC OPL560, OPL561 Series OPL550, OPL551 Series Supply Current(4) ICC Positive-Going Threshold Irradiance(3) EeT(+) OPL550, OPL550-OC, OPL551, OPL551-OC OPL550A, OPL550-OCA, OPL551, OPL551-OCA Hysteresis Ratio EeT(+)/EeT(-) ∆Eet(+) (∆T) Temperature Co-efficient OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC - -0.6 - %/°C >0°C - -1.6 - %/°C <0°C Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue B 10/14 Page 5 of 8 Photologic Sensor OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX OPL550 2.4 3.3 - V OPL551 2.4 3.3 - V OPL560 VCC -2.1 - - V VCC = 4.5 V, IOH = -800 µa, EE = 3 mW/cm2 VCC = 4.5 V, IOH = -800 µa, EE = 0 IOH = -1 µA, EE = 1 mW/cm2 OPL561 VCC -2.1 - - V IOH = -1 µA, EE = 0 OPL530, OPL530-OC, OPL535, OPL535-OC - 0.2 0.4 V IOL = 16 mA, EE = 0 OPL531, OPL531-OC, OPL536, OPL536-OC - 0.2 0.4 V IOL = 16 mA, EE = 1 mW/cm2 OPL550 - 0.25 0.4 V OPL551 - 0.25 0.4 V OPL560, OPL560-OC - - .4 V VCC = 4.5 V, IOL = 12.8 mA, EE = 0 VCC = 4.5 V, IOL = 12.8 mA, EE = 3 mW/cm2 IOL = 16 mA, EE = 0 OPL561, OPL561-OC - - .4 V IOL = 16 mA, EE = 1 mW/cm2 OPL550 -20 -55 -100 mA OPL551 -20 -55 -100 mA VCC = 5.5 V, Output = GND, EE = 3 mW/cm2 VCC = 5.5 V, Output = GND, EE = 0 OPL531, OPL531-OC, OPL536, OPL536-OC - 0.1 10 µA VOH = 30 V, EE = 0 OPL535, OPL535-OC, OPL530, OPL530-OC - 0.1 10 µA VOH = 30 V, EE = 1 mW/cm2 OPL550-OC - 1 100 µA OPL551-OC - 1 100 µA OPL560-OC - - 100 µA VCC = 4.5 V, VOH = 30 V, EE = 3 mW/cm2 VCC = 4.5 V, VOH = 30 V, EE = 0 VOH = 30 V, EE = 1 mW/cm2 OPL561-OC - - 100 µA VOH = 30 V, EE = 0 Operating Supply Voltage VOH Low Level Output Voltage VOL Short Circuit Output Current IOS High Level Output Current(4) IOH UNITS TEST CONDITIONS Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 10/14 Page 6 of 8 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Photologic Sensor OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS Output Rise Time OPL530, OPL531, OPL535, OPL536 - 1.5 - µs EE = 0 or 1 mW/cm2, CL = 50 pF OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC - 50 - ns OPL550, OPL551 - 25 70 ns OPL550-OC, OPL551-OC - 25 70 ns OPL560, OPL561 - - 70 ns OPL560-OC, OPL561-OC - - 100 µs EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 Pf VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, f = 10 kHz, DC = 50% RL = 8 TTL loads VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, f = 10 kHz, DC = 50%, RL = 360 Ω TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz, DC = 50%, RL = 360 Ω - - - tr Output Rise Time OPL530, OPL531, OPL535, OPL536 OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC µs - - ns EE = 0 or 1 mW/cm2, CL = 50 pF EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 pF VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz OPL550-OC, OPL551-OC - 25 70 ns OPL560-OC, OPL561-OC - - 70 ns OPL560, OPL561 - - 70 ns - - 100 ns - 20 - ns EE = 0 or 1 mW/cm2, CL = 50 Pf - 20 - ns - 25 70 ns - - 70 ns - - 100 ns EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 pF VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 360 Ω, f = 10 kHz, DC = 50% TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz tr OPL560-OC, OPL561-OC Output Fall Time OPL530, OPL531, OPL535, OPL536 OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC tf TEST CONDITIONS OPL550-OC, OPL551-OC OPL560, OPL561 OPL560-OC, OPL561-OC Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue B 10/14 Page 7 of 8 Photologic Sensor OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 pF EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 pF VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% Propagation Delay tpEeT(+) OPL530, OPL531, OPL535, OPL536 - 1.0 - µs OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC - 1.0 - µs OPL550-OC, OPL551-OC - 2.5 5 µs OPL530, OPL531, OPL535, OPL536, OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC - 3.0 - µs EE= 0 or 1 mW/cm2, RL = 300 Ω to 5V, CL = 50 pF OPL550-OC, OPL551-OC - 2.5 5 µs VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 360 Ω, f = 10 kHz, DC = 50% OPL560, OPL561 - 5 - µs DC = 50%, RL = 10 TTL Loads OP560-OC, OPL561-OC - 5 - µs DC = 50%, RL = 300 Ω Propagation Delay tpEeT(-) Propagation Delay (Low-High/High-Low) tPLH, TPHL Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 10/14 Page 8 of 8 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com