Datasheet - OPTEK Technology

Photologic® Optical Flag Switch
OPB685, OPB685-3, OPB686, OPB687, OPB688
OPB695, OPB696, OPB697, OPB698 Series
OPB685
Features:
 Photologic® output
 Four output options
 Mechanical switch replacement
 Printed circuit board mounting (OPB685 Series)
 2.5mm, 3-pin connector mates with Molex connector 5051 series
Product Photo Here
OPB695
housing and 4809 series terminal for OPB695 Series
Description:
Each OPB685 and OPB695 series flag switch consists of an infrared emitting diode and a monolithic integrated
circuit that incorporates a photodiode, a linear amplifier and a Schmitt trigger. A lever arm actuated flag interrupts
the light beam, which switches the output between states that can readily drive logic gates.
The OPB695 series is designed to easily snap mount into a 0.037” ± 0.001” (0.940 mm ± 0.025 mm) thick material
with a rectangular opening of 0.320” ± 0.003” x 0.472” (8.13 mm x 11.99 mm) minimum. Insertion into the
punched side of metal is recommended.
Devices in these series feature TTL/LSTTL compatible logic level output that can drive up to 10 TTL loads over a
voltage range from 4.5 V to 16 V.
Customized lever arms and spring torques can be designed for specific applications for each of the devices.
Custom electrical, wire, cabling and connectors are available. Contact your local representative or OPTEK for
more information.
Applications:
 Mechanical switch replacement
 Speed indication (tachometer)
 Mechanical limit indication
 Edge sensing
Ordering Information
Part
Number
LED Peak
Wavelength
Sensor Photologic®
OPB685
10K Pull-Up
OPB686
Open Collector
OPB687
Inv. 10K Pull-Up
OPB688
Inv. Open Collector
Flag Travel
Degrees Max
Lead Length /
Spacing or Connector
59°
0.100" / 0.275"
OPB695AZ
OPB695BZ
10K Pull-Up
OPB695CZ
OPB696AZ
OPB696BZ
890 nm
Open Collector
OPB696CZ
70°
OPB697AZ
OPB697BZ
Inv. 10K Pull-Up
Mates with
3 Pin—Molex
5051 (22-01-1032)
Housing
& 4809 (08-70-0069)
Terminals
OPB697CZ
OPB698AZ
OPB698BZ
Inv. Open Collector
OPB698CZ
RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.3
03/15
Page 1 of 5
Photologic® Optical Flag Switch
OPB685, OPB685-3, OPB686, OPB687, OPB688
OPB695, OPB696, OPB697, OPB698 Series
OPB685, OPB685-3, OPB686, OPB687, OPB688
Pin #
Description
1
Anode
5
Cathode
2
Ground
3
Output
4
VCC
[ MILLIMETERS]
DIMENSIONS ARE IN:
INCHES
OPB695, OPB696, OPB697, OPB698
Part Number
Max. Torque
(Grams)
OPB685
1.5
Pin #
OPB695
OPB685-3
3.0
1
VCC
OPB686
1.5
2
Output
OPB687
1.5
3
Ground
OPB688
1.5
OPB695
1.5
OPB696
1.5
OPB697
1.5
OPB698
1.5
Torque is measured at the
end of the arm from the
resting position to the
switching point of the flag
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.3 03/15
Page 2 of 5
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Photologic® Optical Flag Switch
OPB685, OPB685-3, OPB686, OPB687, OPB688
OPB695, OPB696, OPB697, OPB698 Series
Absolute Maximum Ratings (TA=25°C unless otherwise noted)
Storage & Operating Temperature Range
-40°C to +100°C
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron]
(1)
260°C
Input Diode
Reverse Voltage
2.0 V
Continuous Forward Current
50 mA
Peak Forward Current
3.0 A
(2)
Total Device Power Dissipation
100 mW
Output Photologic®
Supply Voltage, VCC
18 V
Duration of Output Short to VCC
1 second
Voltage at Output
30 V
Low Level Output Current (sinking)
16 mA
Power Dissipation(3) (4)
Notes:
(1)
(2)
(3)
(4)
240 mW
RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
Derate linearly 1.33 mW/°C above 25° C.
Derate linearly 2.00 mW/°C above 25° C (OPB680, OPB680-20, OPB690Z).
Derate linearly 2.50 mW/°C above 25° C (OPB685, OPB686, OPB687, OPB688, OPB695, OPB696, OPB697, OPB698).
OPB685 and OPB695 Series
OPB685, OPB695 Buffered 10K Pull-Up
OPB686, OPB696 Buffered Open-Collector
OPB687, OPB697 Inverted 10K Pull-Up
OPB688, OPB698 Inverted Open-Collector
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.3
03/15
Page 3 of 5
Photologic® Optical Flag Switch
OPB685, OPB685-3, OPB686, OPB687, OPB688
OPB695, OPB696, OPB697, OPB698 Series
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Input Diode
VF
Forward Voltage
-
-
1.6
V
IF = 10 mA
IR
Reverse Current
-
-
100
µA
VR = 3 V
4.5
4.5
8.0
13.5
5.0
12.0
15.0
16.0
8.0
13.5
16.0
-
20
30
mA
mA
Output Photologic® Sensor
VCC
Operating DC Supply Voltage
OPB685 Series
OPB695-698A
OPB695-698B
OPB695-698C
ICC
Operating DC Supply Voltage
OPB695-698A/B/C
ICCL
Low Level Supply Current:
Buffered 10k Pull-Up
Buffered Open-Collector
OPB685
OPB686
-
5.5
4.0
12
12
Inverted 10k Pull-Up
Inverted Open-Collector
OPB687
OPB688
-
6.5
5.0
12
12
mA
VCC = 16 V, IF = 10 mA (no load on output)
High Level Supply Current:
Buffered 10k Pull-Up
Buffered Open-Collector
OPB685
OPB686
-
5.0
12
mA
VCC = 16 V, IF = 10 mA (no load on output)
Inverted 10k Pull-Up
Inverted Open-Collector
OPB687
OPB688
-
4.0
12
mA
VCC = 16 V, IF = 0 mA (no load on output)
OPB685
OPB686
Buffered Open-Collector
OPB695
OPB696A/B/C
-
-
0.4
0.4
0.4
0.4
V
VCC = 4.5 V, IOL = 16 mA, IF = 0
VCC = 4.5 V to 8 V, IOL = 16 mA
VCC = 8.5 V to 13 V, IOL = 16 mA
VCC = 13.5 V to 16 V, IOL = 16 mA
-
-
0.4
0.4
0.4
0.4
V
VCC = 4.5 V, IOL = 16 mA, IF = 0
VCC = 4.5 V to 8 V, IOL = 16 mA
VCC = 8.5 V to 13 V, IOL = 16 mA
VCC = 13.5 V to 16 V, IOL = 16 mA
High Level Output Voltage(2):
Buffered 10k Pull-Up
VCC
-1.5
-
-
V
IOH = 100 µA, IF = 10 mA
Inverted 10k Pull-Up(1)
Inverted Open-Collector
VCC
-1.5
-
-
V
IOH = 100 µA, IF = 0 mA
-
-
100
100
100
100
-
-
100
100
100
100
ICCH
Low Level Output Voltage(1):
Buffered 10k Pull-Up
VOL
Inverted 10k Pull-Up(2)
OPB685
OPB686
Inverted Open-Collector
OPB695
OPB696A/B/C
V
VCC = 16 V, IF = 0 mA (no load on output)
VOH
IOH
High Level Output Voltage(2):
Buffered Open-Collector
OPB686
OPB696A
OPB696B
OPB696C
Inverted 10k Pull-Up(1)
OPB688
OPB698A
OPB698B
OPB698C
µA
µA
VCC = 16 V, IF = 10 mA, VCH = 30 V
VCC = 4.5 V to 8 V, VOH = 30 V
VCC = 8.5 V to 13 V, VOH = 30 V
VCC = 13.5 V to 16 V, VOH = 30 V
VCC = 16 V, IF = 10 mA, VCH = 30 V(1)
VCC = 4.5 V to 8 V, VOH = 30 V(1)
VCC = 8.5 V to 13 V, VOH = 30 V(1)
VCC = 13.5 V to 16 V, VOH = 30 V(1)
Notes: (1) Test requires lever arm in “blocked” posi on. (2) Test requires lever arm in “unblocked” posi on. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.3 03/15
Page 4 of 5
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Photologic® Optical Flag Switch
OPB685, OPB685-3, OPB686, OPB687, OPB688
OPB695, OPB696, OPB697, OPB698 Series
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
LED Positive-Going Threshold Current
OPB685-688
0.1
1.8
10
mA
VCC = 5 V
Hysteresis
1.0
1.2
1.6
mA
VCC = 5 V
Rise Time, Fall Time
-
30
-
ns
Propagation Delay Low-High & HighLow:
Buffer, 10k Pull-Up
OPB685
Buffer, Open-Collector
OPB686
-
1 (LH)
2 (HL)
-
µs
µs
Inverter, 10k Pull-Up
Inverter, Open-Collector
-
2 (LH)
1( HL)
-
Output Photologic® Sensor (continued)
IF(+)
IF(+)/IF(-)
trtf
tPLHtPHL
OPB685/688
OPB687
OPB688
VCC = 5 V, IF = 0 or 10 mA
RL = 300 Ω, DC = 50%
f = 10 kHz
µs
µs
Notes: (1) Test requires lever arm in “blocked” posi on. (2) Test requires lever arm in “unblocked” posi on
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.3
03/15
Page 5 of 5