Vertical Cavity Surface Emitting Laser in Pill Package OPV320 • • • • • 850nm VCSEL technology High thermal stability Low drive current High output power Flat lens The OPV320 is a Vertical Cavity Surface Emitting Laser (VCSEL) packaged in a flat lens pill package. VCSELs offer many advantages in sensing applications when compared to infrared LEDs. These devices require substantially lower drive currents to obtain the same amount of output power as LEDs. This feature allows VCSELs to be used in low power consumption applications such as battery operated equipment. The flat lens packaging allows the device to be used with secondary optics to create custom beam profiles. The OPV320 is optically and spectrally compatible with Optek’s standard detector products such as the OP600 series phototransistors, OP300 series photodarlingtons and the OP900 series photodiodes. .088±.002 .020±.002 Applications • • • • Non-contact position sensing Photoelectric sensors Optical encoders Light curtains R.010±.001 .044±.002 CLEAR GLASS Light Emission Surface .015±.002 2 .090±.003 .085±.003 Additional laser safety information can be found on the Optek website. See application bulletin #221. Classification is not marked on the device due to space limitations. See package outline for centerline of optical radiance. Operating devices beyond maximum rating may result in hazardous radiation exposure. 1 VCSEL 1 .120 MAX +.001 .060 - .002 Pb 2 RoHS Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com A subsidiary of TT electronics plc VCSEL in Pill Package OPV320 Absolute Maximum Ratings TA = 25o C unless otherwise noted Storage Temperature Range -40° to +100° C Operating Temperature Range -40° to +85° C 260° C(1) Soldering Temperature [1/16 inch (1.6mm) from case for 5 sec with soldering iron] Maximum Forward Peak Current 20 mA Maximum Reverse Voltage 5V Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS POT Total Power Out mW IF = 7 mA ITH Threshold Current 3.0 mA Note 2 VF Forward Voltage 2.2 V IF = 7 mA IR Reverse Current 100 nA VR = 5 V RS Series Resistance 55 ohms Note 3 η Slope Efficiency 0.28 mW/mA Note 4 λ Wavelength 830 ∆λ Optical Bandwidth θ Beam Divergence 1.5 CONDITIONS 20 860 nm 0.85 nm 20 Degrees ∆η/∆T Temp Coefficient of Slope Efficiency -0.50 %/°C (0° - 70°C), Note 4 ∆λ/∆T Temp Coefficient of Wavelength 0.06 nm/°C (0° - 70°C) ∆lTH/∆T Temp Coefficient of Threshold Current ±1.0 mA ∆VF/∆T Temp Coefficient for Forward Voltage -2.5 mV/°C (0° - 70°C), Note 2 (0° - 70°C) NOTES: (1) RMA flux is recommended. Solder dwell time can be increased to 10 seconds when flow soldering. (2) Threshold Current is based on the two line intersection method specified in Telcordia GR-468-Core. Line 1 from 4 mA to 6 mA. Line 2 from 0 mA to 0.5 mA. (3) Series Resistance is the slope of the Voltage-Current line from 5 to 8 mA. (4) Slope efficiency, is the slope of the best fit LI line from 5 mA to 8 mA with 0.25mA test intervals. Normalized Output Power vs. Forward Current Typical Angular Output 200% 100% Normalized Output Power Relative Output 80% 60% 40% 20% 0% -90 -60 -30 0 30 60 Normalized at 7mA, 25°C 100% 90 Angular Displacement—Degrees OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com 0% 0 2 4 6 8 10 12 Forward Current—mA Issue 1.0 08.05 Page 2 of 2