High-Intensity LED in Plastic T-1¾ Package OVLGx0CyB9 Series • • • • Narrow beam angle High brightness LED Water clear plastic package UV resistant epoxy Each device in the OVLG Series is a high intensity LED mounted in a clear plastic T-1¾ package. Each device incorporates an integral molded lens that enables a narrow beam angle and provides an even emission pattern. Designed to produce light over a wide range of drive currents, these LEDs are useful in applications that require a higher on-axis brightness than that achievable with standard lamps. Applications • Indoor/outdoor applications • Variable message boards • Store front signage • Indicators Part Number OVLGB0C6B9 OVLGC0C6B9 OVLGS0C8B9 OVLGY0C9B9 RoHS Material InGaN AlInGaP Emitted Color Intensity Typ. mcd Lens Color Blue Blue-Green Red Yellow 7,200 23,000 14,000 14,000 Clear DO NOT LOOK DIRECTLY AT LED WITH UNSHIELDED EYES OR DAMAGE TO RETINA MAY OCCUR. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 05/2011 Page 1 of 7 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com T-1¾ High-Intensity LED OVLG x0CyB9 Series Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature Range -40 ~ +100 °C Operating Temperature Range -40 ~ +100 °C Reverse Voltage 5V Continuous Forward Current Blue, Blue-Green 25 mA Red, Yellow 50 mA Peak Forward Current (10% Duty Cycle, 1 kHz) 100 mA Power Dissipation Current Linearity vs Ambient Temperature Blue, Blue-Green 100 mW Red, Yellow 120 mW Blue, Blue-Green -0.29 mA/° C Red, Yellow -0.72 mA/° C LED Junction Temperature 125° C Electrostatic Discharge Classification (JEDEC-JESD22-A114F) Class 1C 1 260° C / 5 seconds Lead Soldering Temperature (3 mm from the base of the epoxy bulb) Electrical Characteristics (TA = 25o C unless otherwise noted) SYMBOL IV PARAMETER Luminous Intensity COLOR MIN TYP MAX Blue 4,360 7,200 ---- Blue-Green 11,970 23,000 ---- Red 8,550 14,000 ---- Yellow 8,550 14,000 ---- 2.6 3.2 4.0 1.8 2.0 2.4 ---- ---- 10 Blue 460 470 475 Blue-Green 499 505 511 Red 620 623 630 Yellow 585 589 595 ---- 8 ---- Blue VF Forward Voltage Blue-Green Red Yellow UNITS CONDITIONS mcd IF = 20 mA V IF = 20 mA µA VR = 5 V nm IF = 20 mA deg IF = 20 mA Blue IR Reverse Current Blue-Green Red Yellow λD 2Θ½H-H Dominant Wavelength 50% Power Angle OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 05/2011 Page 2 of 7 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com T-1¾ High-Intensity LED OVLG x0CyB9 Series Standard Bins LEDs are sorted to luminous intensity (IV), forward voltage (VF), and dominant wavelength (λD) bins shown. Each bag will consist of a single intensity bin, single forward voltage bin and single dominant wavelength bin. Orders may be filled with any of the intensity bins or color bins listed in the following tables. Optek will not accept orders for single intensity bins or single color bins. Luminous Intensity (IV ) @ 20mA Forward Voltage (VF ) @ 20mA Dominant Wavelength (nm) Blue: OVLGB0C6B9 Blue: OVLGB0C6B9 & Blue-Green: OVLGC0C6B9 Blue: OVLGB0C6B9 IV Code Min (mlm) Max (mlm) 0W 4,360 6,105 0X 6,105 8,550 0Y 8,550 11,970 0Z 11,970 16,758 Blue-Green: OVLGC0C6B9 IV Code Min (mlm) Max (mlm) nm Code Min (nm) Max (nm) BC 460 465 BD 465 470 BE 470 475 VF Code Min (V) Max (V) A 2.6 2.8 B 2.8 3.0 C 3.0 3.2 D 3.2 3.4 E 3.4 3.6 nm Code Min (nm) Max (nm) F 3.6 3.8 HB 499 502 G 3.8 4.0 HC 502 505 Green: OVLGC0C6B9 0Z 11,970 16,758 Z1 16,758 23,500 HD 505 508 Z2 23,500 32,800 HE 508 511 Z3 32,800 46,000 Luminous Intensity (IV ) @ 20mA Forward Voltage (VF ) @ 20mA Dominant Wavelength (nm) Red: OVLGS0C8B9 Red: OVLGS0C8B9 & Yellow: OVLGY0C9B9 Red: OVLGS0C8B9 IV Code Min (mlm) Max (mlm) 0Y 8,550 11,970 0Z 11,970 16,758 Z1 16,758 23,500 Z2 23,500 32,800 Yellow: OVLGY0C9B9 IV Code Min (mlm) Max (mlm) 0Y 8,550 11,970 0Z 11,970 16,758 Z1 16,758 23,500 Z2 23,500 32,800 nm Code Min (nm) Max (nm) VF Code Min (V) Max (V) RA 620 625 A 1.8 2.0 RB 625 630 B 2.0 2.2 C 2.2 2.4 Yellow: OVLGY0C9B9 nm Code Min (nm) Max (nm) YC 585 587 YD 587 589 YE 589 591 YF 591 593 YG 593 595 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 05/2011 Page 3 of 7 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com T-1¾ High-Intensity LED OVLG x0CyB9 Series Typical Electro-Optical Characteristics Curves—Blue & Blue-Green OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 05/2011 Page 4 of 7 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com T-1¾ High-Intensity LED OVLG x0CyB9 Series Typical Electro-Optical Characteristics Curves—Red & Yellow OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 05/2011 Page 5 of 7 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com T-1¾ High-Intensity LED OVLG x0CyB9 Series Beam Angle: Packaging: 500 pcs per anti-static bag with desiccant Desiccant Barcode Label OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 05/2011 Page 6 of 7 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com T-1¾ High-Intensity LED OVLG x0CyB9 Series Reliability Test LED lamps are checked by reliability tests based on MIL standards. 1. Test Conditions, Acceptable Criteria & Results Test Item Life Test Operation Life Test (OLT) Mechanical Test Environmental Test Classification Std. Test Method MIL-STD-750D Method 1026.3 Test Conditions Duration Unit Acc / Rej Result Criteria TA=25°C , IF=30mA * 1000 Hrs 100 0/1 Pass High Temperature MIL-STD-750D Storage (HTS) Method 1032.1 TA=100°C 1000 Hrs 100 0/1 Pass Low Temperature MIL-STD-750D Storage (LTS) Method 1032.1 TA=—40°C 1000 Hrs 100 0/1 Pass Temp. & Humidity MIL-STD-750D with Bias (THB) Method 103B TA=85°C , Rh=85% IF=20mA 500 Hrs 100 0/1 Pass 100 cycles 100 0/1 Pass 100 cycles 100 0/1 Pass Thermal Shock Test (TST) MIL-STD-750D Method 1056.1 0°C 2min ~ 100°C 2min Temperature Cycling Test (TCT) MIL-STD-750D Method 1051.5 -40°C ~ 25°C ~ 100°C ~ 25°C 30min 5min 30min 5min Solderability MIL-STD-750D Method 2026.4 235±5°C , 5 sec. 1 time 20 0/1 Pass Resistance to Soldering Heat MIL-STD-750D Method 2031.1 260±5°C , 5 sec. 1 time 20 0/1 Pass Lead Integrity MIL-STD-750D Method 2036.3 Load 2.5N (0.25kgf) 0°~90°~0° , bend 3 times 20 0/1 Pass Remark: ( * ) IF = 30mA for AllnGaP chip; IF = 20mA for InGan chip ( ** ) IF = 20mA for AllnGaP chip; IF = 10mA for InGan chip 2. Failure Criteria (TA = 25°C): Test Item Symbol Test Conditions Luminous Intensity IV IF = 20mA Forward Voltage VF IF = 20mA Criteria for Judgment Min. Max LSLx0.7 ** USLx1.1 * ( * ) USL: Upper Standard Level, ( ** ) LSL: Lower Standard Level OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 05/2011 Page 7 of 7 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com