Slotted Optical Switch

Slotted Optical Switch
OPB819Z
Features:
 Non-contact switching
 24” (609 mm) long wire leads
 1.25” ( 31.75 mm) wide slot, 1.38” (35.05 mm) deep slot
Description:
The OPB819Z slotted switch consists of an infrared emitting diode and an NPN silicon phototransistor mounted in
an opaque housing with clear windows for dust protection. Switching of the phototransistor occurs whenever an
opaque object passes through the slot.
The OPB819Z has an 1.38” (35.05 mm) deep and 1.25” (31.75 mm) wide slot allowing for a longer reach of the
optical center line from the mounting plane. The switch housing is designed to use the lens of each component as
the optical aperture resulting in an equivalent aperture diameter of 0.06” (1.52 mm).
Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for
more information.
Color
Applications:
 Non-contact object sensing
 Assembly line automation
 Machine automation
 Equipment security
 Machine safety
ANODE
CATHODE
Description
Color
Description
Red
Anode
White
Collector
Black
Cathode
Green
Emitter
COLLECTOR
EMITTER
Ordering Information
RoHS
Part
Number
LED Peak
Wavelength
OPB819Z
890 nm
Sensor
Slot
Width /
Depth
Transistor 1.26" / 1.38”
Aperture
Emitter/
Sensor
Lead
Length /
Spacing
None
24" / 26
AWG Wire
CONTAINS POLYSULFONE
To avoid stress cracking, we suggest using
ND Industries’ Vibra-Tite for thread-locking.
Vibra-Tite evaporates fast without causing structural
failure in OPTEK’s molded plastics.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue B 10/2014
Page 1 of 3
Slotted Optical Switch
OPB819Z
Absolute Maximum Ratings (TA=25°C unless otherwise noted)
Storage & Operating Temperature Range
-40° C to +85° C
Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron]
(1)
260° C
Input Diode
Forward DC Current
50 mA
Peak Forward Current (1 µs pulse width, 300 pps)
3A
Reverse DC Voltage
2V
Power Dissipation
(2)
100 mW
Output Phototransistor
Collector-Emitter Voltage
30 V
Emitter-Collector Voltage
5V
Collector DC Current
30 mA
Power Dissipation(2)
100 mW
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Input Diode
VF
Forward Voltage
-
-
1.8
V
IF = 20 mA
IR
Reverse Current
-
-
100
µA
VR = 2.0 V
Output Phototransistor
V(BR)(CEO)
Collector-Emitter Breakdown Voltage
30
-
-
V
IC = 100 µA, IF = 0, EE = 0
V(BR)(ECO)
Emitter-Collector Breakdown Voltage
5
-
-
V
IE = 100 µA, IF = 0, EE = 0
Collector-Emitter Leakage Current
-
-
100
nA
VCE = 10 V, IF = 0, EE = 0
0.5
-
12.0
mA
VCE = 5 V, IF = 40 mA
-
-
0.4
V
ICEO
Coupled
IC(ON)
On-State Collector Current
VCE(SAT)
Notes:
(1)
(2)
(3)
(4)
(5)
Collector-Emitter Saturation Voltage
IC = 250 µA, IF = 40 mA
RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
Derate linearly 1.67 mW/°C above 25° C.
All parameters tested using pulse techniques.
Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and
ketones. Spray and wipe. Do not submerge.
Polarity is denoted by color the wires: LED (Anode—Red, Cathode—Black); Phototransistor (Collector—White, Emitter—Green).
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue B 10/2014
Page 2 of 3
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Slotted Optical Switch
OPB819Z
OPB819 - Flag Next to Sensor
OPB819 - Flag Next to Emitter
1.20
1.20
Top to Bottom
Top to Bottom
1.00
Normalized IC(ON) Response
Normalized IC(ON) Response
1.00
0.80
0.60
Left to Right
Right to Left
0.40
0.20
0.00
0.00
0.80
0.60
Left to Right
Right to Left
0.40
0.20
0.05
0.10
0.15
0.20
0.25
0.30
0.00
0.00
0.05
Displacement Distance (inches)
0.10
0.15
0.20
0.25
0.30
Displacement Distance (inches)
OPB819 - Flag in Middle of Slot
1.20
Top to Bottom
0
Top to Bottom
Normalized IC(ON) Response
1.00
0.80
Emitter
0.60
Left to Right
Left to Right
Right to Left
Right to Left
Sensor
0.40
0
Width
0.20
0.00
0.00
0.05
0.10
0.15
0.20
0.25
0.30
Displacement Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue B 10/2014
Page 3 of 3