Sensing and Control SMD Receiver Component OPL6000 Features: • • • • • • Up to 256kbps OperaƟon Up to 250klux Ambient Light Immunity Output Drive for Interfacing to Microcontroller Reverse Gull Wing Design Compliant with Smart Power Meter Standard ANSI C12.18 CompaƟble with OP181 EmiƩer Component DescripƟon: The OPL6000 is a surface mount receiver component incorporaƟng a custom CMOS ASIC. The product features a digital output in a push-pull inverter design. The circuitry provides ambient light immunity while maintaining low power consumpƟon. The ASIC is lead frame mounted and overmolded, incorporaƟng a lens to achieve maximum light coupling ability. In addiƟon, the overmold compound provides visible light rejecƟon. While this part has been designed specifically for the smart power meter industry, other applicaƟons are certainly possible. ApplicaƟons: • • Smart power meter opƟcal port Over the air communicaƟons Note: The VDD and N/C leads are the wider of the four leads as indicated above but also have red strip indicator on the boƩom of the leads. Dimensions are ±0.005 unless otherwise specified General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 1 Sensing and Control SMD Receiver Component OPL6000 Absolute Maximum RaƟngs (TA = 25° C unless otherwise noted) Overall Product -55o C to +100o C Storage Temperature Range -40o C to +85o C OperaƟng Temperature Range D.C. Supply Voltage 3.0 - 5.5 V Output Drive Current 1 mA Power DissipaƟon in AcƟve / InacƟve Mode (1)(2) 30 mW / 5mW(2) Incident Irradiance Solder Reflow Temperature 250,000 lux (3) 260° C Notes: 1. AcƟve mode is defined as the state during which Ɵme a signal is being received and the output stages are acƟve. InacƟve mode is defined as the state during which Ɵme no signal is being received and the output stages are inacƟve. 2. Derate linearly at 0.40 mW/°C (acƟve mode) and 0.067 mW/°C (inacƟve mode) above 25°C.Solder Ɵme less than 5 seconds at temperature extreme. 3. Solder Ɵme less than 5 seconds at temperature extreme. Solder Ɵme within 5° of peak temperature is 20 to 40 seconds. Recommended PCB Layout General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 2 Sensing and Control SMD Receiver Component OPL6000 Electrical SpecificaƟons Electrical CharacterisƟcs (TA = 25 °C unless otherwise noted) SYMBOL VDD IDD PARAMETER MIN TYP MAX UNITS 3.0 3.3 5.5 V AcƟve Mode - - 5 InacƟve Mode - - 1.0 10 - - % OperaƟng Supply Voltage Supply Current(1) mA TEST CONDITIONS VDD = 3.0 to 5.5 V No load current PSRR Power Supply RejecƟon RaƟo EeT(+) PosiƟve Going Threshold Irradiance - 0.100 0.125 mW/cm2 VOL Low Level Output Voltage - 300 400 mV VDD = 3.0 to 5.5 V, IO = 1 mA Ee = 0 mW/cm2 VOH High Level Output Voltage VDD - 1.0 - - V VDD = 3.0 to 5.5 V, IO = 1 mA Ee = 7.5 mW/cm2 tr, tf Rise Time, Fall Time - - 150 ns - - 1.0 µs tPDLH, tPDHL PropagaƟon Delay II Input Leakage Current -10 - 10 µA IO Output Drive Current - - 1.0 mA f = 1 - 1 MHz, VDD > 3.0V VDD = 3.3 V lp = 940 nm; collimated radiaƟon VDD = 3.3 V, f = 1 kHz Ee = 7.5 mW/cm2 Decouple Cap (VDD to GND) = 0.1 µF VDD = 3.3 V Notes: 1. AcƟve mode is defined as the state during which Ɵme a signal is being received and the output stages are acƟve. InacƟve mode is defined as the state during which Ɵme no signal is being received and the output stages are inacƟve. General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 3 Sensing and Control SMD Receiver Component OPL6000 Supply Current General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 4 Sensing and Control SMD Receiver Component OPL6000 Rise/Fall Time General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 5 Sensing and Control SMD Receiver Component OPL6000 PropagaƟon Delay General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 6 Sensing and Control SMD Receiver Component OPL6000 Pulse Width DistorƟon General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 7 Sensing and Control SMD Receiver Component OPL6000 High and Low Level Output Voltage General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 8 Sensing and Control SMD Receiver Component OPL6000 SensiƟvity General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 9 Sensing and Control SMD Receiver Component OPL6000 Frequency Response General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 10 Sensing and Control SMD Receiver Component OPL6000 Packaging Notes: 1. Dimensions are in mm. 2. VDD and N/C lead (marked with red stripe) is nearest sprocket holes. General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.Ʃelectronics.com Issue B 01/2015 Page 11