Sensing and Control Fiber Optic Isolator - Photologic® Sensor OPI1290 Series Features: • Opaque plas c housings • High noise immunity • IR LED with Phototransistor Output • 0.05” (1.27 mm) lead spacing • Data Transfer through plas c fiber op c cable • Isola on voltage 15 KV (OPI1290-032), Longer versions higher DescripƟon: Each OPI1290 consists of a IR LED and a Photologic® Totem-Pole output sensor, which are housed in separate opaque molded plas c housings and coupled by plas c fiber op c cable. The heavy-duty opaque housing shields the op cal signal from dust, making this series of devices ideal for dust contaminated environments. The OPI1290 series are designed for applica ons that require high voltage isola on between input and output or signal communica on over short distances. Depending on the length of the fiber op c cable, the emi er does not have to be op cally in-line with the sensor. The isola on voltage is greater than 10 K volts per inch (Isola on distance between components) for all versions of the OPI1290. Custom electrical, wire and cabling and connectors are available. Contact your local representa ve or OPTEK for more informa on. Ordering InformaƟon ApplicaƟons: • • • • • Requiring High Voltage isola on between input and output Electrical isola on in dirty environments Industrial equipment Medical equipment Office equipment Device Length ±2mm Part Number IsolaƟon Distance ±2mm Device Length ±2mm OPI1290-018 0.86” [22 mm] 1.26” [32.0 mm] OPI1290-026 1.18” [30 mm] 1.57” [40.0 mm] OPI1290-032 1.42” [36 mm] 1.80” [45.8 mm] OPI1290-040 1.73” [44 mm] 2.12” [53.8 mm] OPI1290-066 2.76” [70 mm] 3.15” [80.0 mm] OPI1290-080 3.31” [84 mm] 3.69” [93.8 mm] Isolation Distance LED Peak Lead Length Wavelength 0.45” [11.4 mm] 890 nm Pin # LED 1 Anode 2 Cathode 3 VCC 4 Output 5 Ground VCC An Output RoHS General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data and is considered accurate at Ɵme of going to print. © TT electronics plc Cathode Ground 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www. electronics.com Issue D 06/2015 Page 1 Sensing and Control Fiber Optic Isolator - Photologic® Sensor OPI1290 Series Absolute Maximum RaƟngs (TA=25°C unless otherwise noted) Storage Temperature Range (note 3) -40o C to +80o C Opera ng Temperature Range (note 3) -20° C to +75° C Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 260° C(1) Power Dissipa on (2) 100 mW Electrical CharacterisƟcs (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS 1.2 - 2.3 V IF = 20 mA - - 80 µA VR = 3.0 V LED (See OP240 for addi onal informa on) VF On-State Collector Current IR Collector-Dark Current Photologic® Sensor (See OP550 for addi onal informa on) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS 4.5 - 16 V - Peak-to-Peak VCC Ripple Necessary to Cause False Triggering of Output - - 2 V VCC = 5 V DC, f = DC to 50 MHz Supply Current(4) - 8 15 mA EE = 0 or 3 mW/cm2, VCC = 5.5 V Posi ve-Going Threshold Irradiance(2) .25 - 2.4 Hysteresis Ra o 1.50 2 2.5 - Opera ng Supply Voltage VCC ICC EeT(+) EeT(+)/EeT(-) mW/cm2 VCC = 5 V, TA = 25° C - VOH Opera ng Supply Voltage 2.1 - - V IOH = -1 µA, EE = 1 mW/cm2 VOL Low Level Output Voltage - 0.25 0.4 V VCC = 4.5 V, IOL = 12.8 mA, EE = 0 IOS Short Circuit Output Current -20 -55 -100 mA VCC = 5.5 V, Output = GND, EE = 3 mW/cm2 IOH High Level Output Current(2) - 1 100 µA VCC = 4.5 V, VOH = 30 V, EE = 3 mW/cm2 TR & TF Output Rise & Fall Time - 25 70 ns VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/ cm2, f = 10 kHz, DC = 50% RL = 8 TTL loads tpEeT(+) Propaga on Delay Posi ve–Going - 2.5 5.0 µs VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% tpEeT(-) Propaga on Delay Nega ve–Going - 2.5 5.0 µs VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/ cm2, RL = 360 Ω, f = 10 kHz, DC = 50% tPLH, TPHL Propaga on Delay (Low-High/High-Low) - 5.0 - µs DC = 50%, RL = 10 TTL Loads Notes: (1) (2) (3) Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. Irradiance measurements are made with λi = 935 nm. Storage and Opera ng temperature values are based on the plas c op cal interface temperature ra ngs. Please reference UL1577 and UL file AVLVZ.E89328 General Note TT Electronics reserves the right to make changes in product specificaƟon without noƟce or liability. All informaƟon is subject to TT Electronics’ own data © TT electronics plc 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www. electronics.com Issue D 06/2015 Page 2