M272 1 Form B Solid State Relay DESCRIPTION The M272 is a bi-directional, single-pole, single-throw, normally closed multipurpose solid-state relay in a miniature 4-pin small outline package. It is designed to be a cost-effective replacement of reed relays in low voltage applications. The relay consists of an integrated circuit that drives two rugged source-to-source depletion type DMOS transistors - optically coupled to a light emitting diode. The output MOS transistors are protected with free-wheeling diodes that can handle up to 1.5A of inrush current, making the relay ideal for switching lamps and highly inductive loads. FEATURES APPLICATIONS • 1 Form B (normally closed) SSR • Telecom switching • Low input control power consumption (1.5mA TYP) • Tip/Ring control • High Load Current Rating (125mA) • Medical equipment • Low on-resistance (3 ohms MAX) • Battery monitoring • Ultra miniature 4-pin small outline package • Home/Safety security systems • High input-to-output isolation (1500Vrms MIN) • Meter reading systems • Long life/high reliability OPTIONS/SUFFIXES* • -TR ABSOLUTE MAXIMUM RATINGS* PARAMETER UNIT MIN Storage Temperature °C -55 125 Operating Temperature °C -40 85 Continuous Forward Current mA 50 Peak Forward Current (1us) A 1 Reverse Input Control Voltage V 5 mW 400 Tape and Reel packing option (2,000 pcs / reel) NOTE: Suffixes listed above are not included in marking on device for part number identification. TYP MAX SCHEMATIC DIAGRAM Output Power Dissipation *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. APPROVALS • © 2009 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 1 of 5 UL/C-UL Approved: File # E201932 M272 rev 1.42 (6/25/2009) M272 1 Form B Solid State Relay ELECTRICAL CHARACTERISTICS - 25°C PARAMETER UNIT MIN TYP MAX 1.2 1.5 TEST CONDITIONS INPUT SPECIFICATIONS LED Forward Voltage V LED Reverse Voltage V Turn-On Current Turn-Off Current 6 If = 10mA 12 Ir = 10uA mA 0.5 Io = 100mA mA 1.5 5 Io = 100mA OUTPUT SPECIFICATIONS Blocking Voltage V Continuous Load Current mA On-Resistance Ω Leakage Current Output Capacitance Offset Voltage 60 Io = 1uA 125 If = 0mA 2 3 Io = 125mA µA 0.05 1 Vo = 60V pF 25 50 Vo = 25V, f = 1.0MHz 0.2 If = 0mA mV COUPLED SPECIFICATIONS Isolation Voltage Turn-On Time 1500 V T = 1 minute ms 0.08 Turn-Off Time ms 1 Isolation Resistance GΩ Coupled Capacitance pF Contact Transient Ratio © 2009 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 V/ 2 If = 0mA, Io = 100mA, Vo = 20V 3 If = 10mA, Io = 100mA, Vo = 20V 100 3 µs 2000 Page 2 of 5 7000 dV = 50V M272 rev 1.42 (6/25/2009) M272 1 Form B Solid State Relay PERFORMANCE DATA M272 M272 Typical Turn-On Time Distribution N = 100, Ambient Temperature = 25°C Typical Turn-Off Time Distribution N = 100, Ambient Temperature = 25°C 40 Device Count 40 30 20 10 0 30 20 10 0 0.06 0.06 0.07 0.07 0.08 0.08 0.09 0.09 0.2 0.4 Turn-On Tim e (m s) 1 1.2 1.4 1.6 M272 M272 Typical On-Resistance Distribution N = 100, Ambient Temperature = 25°C Typical Leakage Current Distribution N = 100, Ambient Temperature = 25°C 40 Device Count 30 20 10 0 1.6 1.8 2 2.2 2.4 2.6 20 10 0 2.8 0 0.02 0.03 0.04 0.05 0.06 0.07 0.08 On-Resistance (ohm s) Leakage Current (uA) M272 Maximum Load Current vs. Temperature 0 60 65 70 75 80 85 90 95 Blocking Voltage (V) © 2009 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 50 0 80 10 100 60 20 -2 0 30 150 -4 0 40 Load Current (mA) M272 Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25°C 40 1.4 30 20 Device Count 0.8 Turn-Off Tim e (m s) 40 Device Count 0.6 0 Device Count 50 Tem perature (C) Page 3 of 5 M272 rev 1.42 (6/25/2009) M272 1 Form B Solid State Relay MECHANICAL DIMENSIONS 4 PIN SMALL OUTLINE PACKAGE END VIEW TOP VIEW BACK VIEW © 2009 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 4 of 5 M272 rev 1.42 (6/25/2009) M272 1 Form B Solid State Relay DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2009 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 5 of 5 M272 rev 1.42 (6/25/2009)