M212 1 Form B 400V / 35Ω MOSFET Output Solid State Relay Description Features The M212 is a bi-directional, single-pole, single-throw, normally closed multipurpose solid-state relay in a miniature 4-pin small outline package. It is designed to replace electromechanical relays in general purpose switching applications. The relay consists of an integrated circuit that drives two rugged source-to-source depletion type DMOS transistors - optically coupled to a light emitting diode. The output MOS transistors are protected with freewheeling diodes that can handle up to 1.5A of inrush current, making the relay ideal for switching lamps and highly inductive loads. High Input-to-Output Isolation (1.5kV MIN) Low Input Control Current (1.5mA TYP) 120mA Maximum Continuous Load Current Low On Resistance (35 MAX) Ultra Miniature 4SOP Package Long Life / High Reliability RoHS / Pb-Free / REACH Compliant Agency Approvals The M212 comes standard in a 4 pin SOP package. UL/C-UL: VDE: File # E201932 File # 40035191 (EN 60747-5-2) Applications Medical Equipment Security Systems Meter Reading Equipment Data Acquisition Battery Monitoring Multiplexers Absolute Maximum Ratings The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to absolute Maximum Ratings may cause permanent damage to the device and may adversely affect reliability. Schematic Diagram (+) Input 1 4 (+/-) Load (-) Input 2 3 (-/+) Load Storage Temperature …………………………..-55 to +125°C Operating Temperature …………………………-40 to +85°C Continuous Input Current ………………………………..50mA Transient Input Current ………………….……………..500mA Reverse Input Control Voltage …………..…………………5V Input Power Dissipation …………………………………40mW Total Power Dissipation ……………………………..400mW Solder Temperature – Wave (10sec)……………….….260°C Solder Temperature – IR Reflow (10sec)….…………..260°C Ordering Information M212 Part Number M212 M212-TR Description 4 pin SOP, (100/Tube) 4 pin SOP, Tape and Reel (2000/Reel) NOTE: Suffixes listed above are not included in marking on device for part number identification © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 1 of 7 M212/TR Rev 2.00 (07/12/2013) 001603 M212 1 Form B 400V / 35Ω MOSFET Output Solid State Relay Electrical Characteristics, TA = 25°C (unless otherwise specified) Parameter Symbol Min. Typ. Max. 1.5 Units Test Conditions V IF = 10mA Input Specifications LED Forward Voltage VF - 1.2 LED Reverse Voltage BVR 5 - - V IR = 10μA Input Reverse Current IR - - 10 A VR = 5V Turn-On Current IF - 0.5 - mA IO = 100mA Turn-Off Current IF(OFF) - 1.5 5.0 mA IO = 100mA Blocking Voltage VB 400 - - V IO=1A Continuous Load Current IO - - 120 mA IF=0mA RON - 25 35 Ω IF=0mA, IO=100mA Output Specifications On Resistance Leakage Current IOleak - 0.2 1 A IF=5mA, VO=400V Output Capacitance COUT - 25 - pF VO=25V, f=1.0MHz VOFFSET - - 0.2 mV IF=0mA TON - 0.1 0.5 mS IF=0mA, IO=100mA IF=5mA, IO=100mA Offset Voltage Coupled Specifications Turn-On Time Turn-Off Time TOFF - 1.5 3 mS CCOUPLED - 3 - pF - 2,000 7,000 0 V/S Isolation Voltage VISO 1500 - - VRMS RH ≤ 50%, t=1min Input-Output Resistance RI-O - - VI-O = 500VDC Coupled Capacitance Contact Transient Ratio dV = 50V Isolation Specifications © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 10 Page 2 of 7 12 M212/TR Rev 2.00 (07/12/2013) 001603 M212 1 Form B 400V / 35Ω MOSFET Output Solid State Relay M212 Performance & Characteristics Plots, TA = 25°C (unless otherwise specified) © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 3 of 7 M212/TR Rev 2.00 (07/12/2013) 001603 M212 1 Form B 400V / 35Ω MOSFET Output Solid State Relay M212 Solder Reflow Temperature Profile Recommendations (1) Infrared Reflow: Refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow. Soldering process should not exceed temperature or time limits expressed herein. Surface temperature of device package should not exceed 250ºC: G F D E H B A C Process Step A B C D E F G H Description Preheat Start Temperature (ºC) Preheat Finish Temperature (ºC) Preheat Time (s) Melting Temperature (ºC) Time above Melting Temperature (s) Peak Temperature, at Terminal (ºC) Dwell Time at Peak Temperature (s) Cool-down (ºC/s) Parameter 150ºC 180ºC 90 - 120s 230ºC 30s 260ºC 10s <6ºC/s (2) Wave Solder: Maximum Temperature: Maximum Time: Pre-heating: Single Occurrence 260ºC (at terminal) 10s 100 - 150ºC (30 - 90s) (3) Hand Solder: Maximum Temperature: Maximum Time: Single Occurrence © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 350ºC 3s (at tip of soldering iron) Page 4 of 7 M212/TR Rev 2.00 (07/12/2013) 001603 M212 1 Form B 400V / 35Ω MOSFET Output Solid State Relay M212 Package Dimensions 4 PIN SOP Package © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: All dimensions in inches with millimeters [mm] in parenthesis () Page 5 of 7 M212/TR Rev 2.00 (07/12/2013) 001603 M212 1 Form B 400V / 35Ω MOSFET Output Solid State Relay M212 Packaging Specifications Tape & Reel Specifications (T&R) © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 6 of 7 All dimensions in millimeters [mm] M212/TR Rev 2.00 (07/12/2013) 001603 M212 1 Form B 400V / 35Ω MOSFET Output Solid State Relay M212 Package Marking DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notices. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 7 of 7 M212/TR Rev 2.00 (07/12/2013) 001603