SMA4122 1 Form A 100V / 30mΩ DC MOSFET Output Solid State Relay Description Features The SMA4122 is a DC, single-pole, single-throw, normally open solid-state relay in a 4 pin single inline package. The relay consists of an AlGaAs LED, optically coupled to a high performance Photo Diode Array (PDA), which in turn drives a low on-resistance, rugged source-to-source enhancement type DMOS transistor output. The SMA4122 has an extremely low on resistance of 15m (TYP) and a very high continuous load current rating of up to 6 amps. The combination of low on-resistance, small package outline and high load current capabilities make the SMA4122 a unique, unparalleled solid state relay. 100VDC Blocking Voltage Extremely Low On Resistance (15m TYP) High Continuous Load Current (6 Amps) High Input-to-Output Isolation ( up to 5kVRMS) Long Life / High Reliability RoHS / Pb-Free / REACH Compliant Agency Approvals The SMA4122 comes standard in a 4 pin SIP package. UL: C-UL: File # E201932 File # E201932 Applications Reed Relay / EMR Replacement Meter reading systems Data Acquisition Medical Equipment Battery Monitoring Home/Safety Security Systems Absolute Maximum Ratings The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to absolute Maximum Ratings may cause permanent damage to the device and may adversely affect reliability. Schematic Diagram Storage Temperature …………………………..-55 to +125°C Operating Temperature ………………………-40 to +85°C Continuous Input Current ………………………………..50mA Transient Input Current ………………….……………..500mA Reverse Input Control Voltage …………..…………………5V Input Power Dissipation …………………………………40mW Total Power Dissipation ……………………………..…..1.2W Solder Temperature – Wave (10sec)……………….….260°C Solder Temperature – IR Reflow (10sec)….…………..260°C Ordering Information Part Number Description SMA4122 SMA4122-H 4 pin SIP, (25/Tube) 5kVRMS VISO, 4 pin SIP, (25/Tube) NOTE: Suffixes listed above are not included in marking on device for part number identification © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 1 of 6 SMA4122 Rev 2.00 (11/25/2013) 001753 SMA4122 1 Form A 100V / 30mΩ DC MOSFET Output Solid State Relay Electrical Characteristics, TA = 25°C (unless otherwise specified) Parameter Symbol Min. Typ. Max. 1.8 Units Test Conditions V IF = 10mA Input Specifications LED Forward Voltage VF - 1.4 LED Reverse Voltage BVR 5 - - V IR = 10μA Input Reverse Current IR - - 10 A VR = 5V Turn-On Current IF - 10 15 mA IO = 2A (within 10mS) Turn-Off Current IFOFF - 2 - mA IO = 2A Blocking Voltage VB 100 - - V IF = 0mA, IO = 1A Continuous Load Current IO - - 6 A IF = 15mA RON - 15 30 mΩ IF = 15mA, IO = 2A Output Specifications On Resistance IOleak - 0.1 1 A IF = 0mA, VO = 100V VOFFSET - - 0.2 mV IF = 15mA Turn-On Time TON - 10 15 mS IF = 15mA, IO = 2A Turn-Off Time TOFF - 0.5 2 mS IF = 0mA, IO = 2A Leakage Current Offset Voltage Coupled Specifications Coupled Capacitance Contact Transient Ratio CCOUPLED - 3 - pF - 2,000 7,000 0 V/S 3750 - - 5000 - - dV = 50V Isolation Specifications Isolation Voltage (-H Option) Input-Output Resistance © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 VISO RI-O - 10 Page 2 of 6 12 - VRMS RH ≤ 50%, t=1min VI-O = 500VDC SMA4122 Rev 2.00 (11/25/2013) 001753 SMA4122 1 Form A 100V / 30mΩ DC MOSFET Output Solid State Relay SMA4122 Performance & Characteristics Plots, TA = 25°C (unless otherwise specified) IF=15mA IO=2A IF=15mA IO=2A © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 3 of 6 SMA4122 Rev 2.00 (11/25/2013) 001753 SMA4122 1 Form A 100V / 30mΩ DC MOSFET Output Solid State Relay SMA4122 Solder Reflow Temperature Profile Recommendations (1) Infrared Reflow: Refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow. Soldering process should not exceed temperature or time limits expressed herein. Surface temperature of device package should not exceed 250ºC: G F D E H B A C Process Step A B C D E F G H Description Preheat Start Temperature (ºC) Preheat Finish Temperature (ºC) Preheat Time (s) Melting Temperature (ºC) Time above Melting Temperature (s) Peak Temperature, at Terminal (ºC) Dwell Time at Peak Temperature (s) Cool-down (ºC/s) Parameter 150ºC 180ºC 90 - 120s 230ºC 30s 260ºC 10s <6ºC/s (2) Wave Solder: Maximum Temperature: Maximum Time: Pre-heating: Single Occurrence 260ºC (at terminal) 10s 100 - 150ºC (30 - 90s) (3) Hand Solder: Maximum Temperature: Maximum Time: Single Occurrence © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 350ºC 3s (at tip of soldering iron) Page 4 of 6 SMA4122 Rev 2.00 (11/25/2013) 001753 SMA4122 1 Form A 100V / 30mΩ DC MOSFET Output Solid State Relay SMA4122 Package Dimensions 4 PIN SIP Package © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 5 of 6 All dimensions in inches with millimeters [mm] in parenthesis () SMA4122 Rev 2.00 (11/25/2013) 001753 SMA4122 1 Form A 100V / 30mΩ DC MOSFET Output Solid State Relay SMA4122 Package Marking SMA4122 Package Weights Device SMA4122-(H) Single Unit Full Tube (25pcs) Full Pouch (10 tubes) 0.88 35 370 Note: All weights above are in GRAMS, and include packaging materials where applicable DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notices. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 6 of 6 SMA4122 Rev 2.00 (11/25/2013) 001753