Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
SKY13415-485LF: 0.1 to 3.0 GHz SP5T Antenna Switch
Applications
 Any 2G/3G/4G antenna diversity or LTE (TDD/FDD)
transmit/receive system
RF1
RF2
Description
The SKY13415-485LF is a Single Pole, Five-Throw (SP5T)
antenna switch with an internal 50 Ω termination. The high
linearity performance and low insertion loss achieved by the
SKY13415-485LF make it an ideal choice for main/diversity
switching commonly used in LTE-based handsets, data cards,
and tablets that use antenna diversity solutions.
The SKY13415-485LF is part of a scalable family of products that
covers SP4T through SP8T switches that allow up to eight bands
of WCDMA/LTE:
 SKY13414-485LF SP4T Antenna Switch (Data Sheet #201689)
 SKY13415-485LF SP5T Antenna Switch (this Data Sheet)
 SKY13416-485LF SP6T Antenna Switch (Data Sheet #201679)
ANT
RF5
50 Ω
Bias
Decoder
V1
Skyworks Green™ products are compliant with
all applicable legislation and are halogen-free.
For additional information, refer to Skyworks
Definition of Green™, document number
SQ04-0074.
RF4
V2
 Small QFN (14-pin, 2.0 x 2.0 mm) package (MSL1, 260 C per
JEDEC J-STD-020)
RF3
V3
 Broadband frequency range: 0.1 to 3.0 GHz
 Low insertion loss: 0.45 dB typical @ 2.7 GHz
 High isolation: >30 dB @ 2.7 GHz
 Internal 50 Ω port to control diversity antenna impedance when
device is not in use
 Integrated logic
VDD
Features
S2668
Figure 1. SKY13415-485LF Block Diagram
Switching is controlled by three CMOS/TTL-compatible control
voltage inputs (V1, V2, and V3). Depending on the logic voltage
level applied to the control pins, the ANT pin is connected to one
of five switched RF outputs (RF1 to RF5) using a low insertion loss
path, while the paths between the ANT pin and the other RF pins
are in a high isolation state. The antenna path can also be closed
on a 50 Ω load when it needs to be terminated. The 50 Ω load is
internally grounded. No external blocking capacitors are required
on the RF paths unless VDC is externally applied.
The SKY13415-485LF is manufactured in a compact, 14-pin 2.0 x
2.0 mm, Quad Flat No-Lead (QFN) package.
A functional block diagram is shown in Figure 1. The pin
configuration and package are shown in Figure 2. Signal pin
assignments and functional pin descriptions are provided in
Table 1.
 SKY13417-485LF SP7T Antenna Switch (Data Sheet #201661)
 SKY13418-485LF SP8T Antenna Switch (Data Sheet #201712)
The symmetric port designs provide flexibility in signal routing for
both receive diversity and higher power
TD-SCDMA/TDD-LTE, WCDMA/FDD, and LTE transmit/receive
applications.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201704G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 2, 2014
1
N/C
ANT
N/C
DATA SHEET • SKY13415-485LF: SP5T SWITCH
14
13
12
N/C
RF3
2
10
RF4
RF1
3
9
RF2
VDD
4
8
N/C
5
6
7
V1
11
V2
1
V3
RF5
S2669
Figure 2. SKY13415-485LF Pinout – 14-Pin QFN
(Top View)
Table 1. SKY13415-485LF Signal Descriptions (Note 1)
Pin
Name
Description
Pin
8
Name
N/C
Description
1
RF5
RF I/O path 5
Not connected
2
RF3
RF I/O path 3
9
RF2
RF I/O path 2
3
RF1
RF I/O path 1
10
RF4
RF I/O path 4
4
VDD
DC power supply
11
N/C
Not connected
5
V3
DC control voltage 3
12
N/C
Not connected
6
V2
DC control voltage 2
13
ANT
Antenna port
7
V1
DC control voltage 1
14
N/C
Not connected
Note 1: Bottom ground paddles must be connected to ground.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
2
May 2, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201704G
DATA SHEET • SKY13415-485LF: SP5T SWITCH
Table 2. SKY13415-485LF Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Minimum
Maximum
Units
5.0
V
Supply voltage
VDD
2.5
Control voltage (V1, V2, and V3)
VCTL
–0.5
RF input power (RF1 to RF5)
PIN
RF power applied to antenna in the 50 Ω switched RF output state
PIN
Operating temperature
TOP
–40
Storage temperature
TSTG
–55
Electrostatic discharge:
ESD
Human Body Model (HBM), Class 1C
+3.0
V
+37.5
dBm
+27
dBm
+85
C
+150
C
1000
V
Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Functional Description
Electrical and Mechanical Specifications
The SKY13415-485LF includes an internal negative voltage
generator and decoder that eliminate the need for external DC
blocking capacitors on the RF ports. No external components are
required for proper operation. DC decoupling capacitors may be
added on the VDD and control lines if necessary.
The absolute maximum ratings of the SKY13415-485LF are
provided in Table 2. Electrical specifications are provided in
Table 3.
Switching is controlled by three control voltage inputs, V1, V2, and
V3. Depending on the logic voltage level applied to the control
pins, the antenna pin is connected to one of five switched RF
outputs or a 50 Ω termination.
The isolation matrix shown in Table 5 provides the port-to-port
and antenna-to-port isolation for all available RF states at three
different frequencies: 1.0 GHz, 2.0 GHz, and 2.7 GHz.
The state of the SKY13415-485LF is determined by the logic
shown in Table 4.
Shutdown mode is enabled by connecting all three control pins
(V1, V2, and V3) to logic high. This mode reduces the overall
current consumption of the device to 5 μA typical.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201704G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 2, 2014
3
DATA SHEET • SKY13415-485LF: SP5T SWITCH
Table 3. SKY13415-485LF General Electrical Specifications (Note 1)
(VDD = 2.6 V, V1 = V2 = V3 = 0/1.8 V, PIN = 0 dBm, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
(Note 2)
Min
Typical
Max
Units
2.5
3.0
4.8
V
40
50
μA
1.80
2.70
0.4
V
V
0.5
1.0
μA
DC Specifications
Supply voltage
VDD
Supply current
IDD
Control voltage:
High
Low
VCTL_H
VCTL_L
Control current
ICTL
VCTL = 1.8 V
Shutdown mode supply current
Ioff
V1/2/3 = 1.8 V, VDD = 3 V
5
10
μA
Turn-on switching time
tON
50% of control voltage to
90% of final RF power,
switching between
RF1/2/3/4/5/50_OHM
1.75
2.20
μs
0.40
0.40
0.45
0.50
0.50
0.60
dB
dB
dB
1.35
RF Specifications
Insertion loss (ANT pin to RF1/2/3/4/5 pins)
IL
0.1 to 1.0 GHz
1.0 to 2.0 GHz
2.0 to 2.7 GHz
Isolation (ANT pin to RF1/2/3/4/5 pins)
Iso
0.1 to 1.0 GHz
1.0 to 2.0 GHz
2.0 to 2.7 GHz
38
32
27
42
34
31
dB
dB
dB
Input return loss (ANT pin to RF1/2/3/4/5
pins)
RL
0.1 to 1.0 GHz
1.0 to 2.0 GHz
2.0 to 2.7 GHz
21
23
15
24
25
18
dB
dB
dB
Second harmonics (ANT pin to RF1/2/3/4/5
pins)
2fo
PIN = +26 dBm,
0.1 to 3.0 GHz
+95
dBc
Third harmonics (ANT pin to RF1/2/3/4/5
pins)
3fo
PIN = +26 dBm,
0.1 to 3.0 GHz
+104
dBc
GSM harmonics:
2fo, 3fo
High band
PIN = +33 dBm, 50 Ω
PIN = +33 dBm, 3:1 VSWR
–48
–42
dBm
dBm
Low band
PIN = +34.5 dBm, 50 Ω
PIN = +34.5 dBm, 3:1 VSWR
–50
–44
dBm
dBm
+37.5
dBm
+70
dBm
0.1 dB Compression Point (ANT pin to
RF1/2/3/4/5 pins)
rd
3 Order Input Intercept Point
50 Ω power handling
P0.1dB
IIP3
0.8 GHz to 3.0 GHz
@ 2.0 GHz, PIN = +26 dBm,
Δf = 1 MHz
0.1 GHz to 3.0 GHz
+27
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
4
May 2, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201704G
dBm
DATA SHEET • SKY13415-485LF: SP5T SWITCH
Table 4. SKY13415-485LF Control Logic (Note 1)
Control Pins
Switched RF Outputs
V1
(Pin 7)
V2
(Pin 6)
V3
(Pin 5)
RF1
(Pin 3)
RF2
(Pin 9)
RF3
(Pin 2)
RF4
(Pin 10)
RF5
(Pin 1)
50 Ω
0
0
0
Insertion Loss
Isolation
Isolation
Isolation
Isolation
Isolation
0
0
1
Isolation
Insertion Loss
Isolation
Isolation
Isolation
Isolation
0
1
0
Isolation
Isolation
Insertion Loss
Isolation
Isolation
Isolation
0
1
1
Isolation
Isolation
Isolation
Insertion Loss
Isolation
Isolation
1
0
0
Isolation
Isolation
Isolation
Isolation
Insertion Loss
Isolation
1
0
1
Isolation
Isolation
Isolation
Isolation
Isolation
50 Ω
1
1
0
Isolation
Isolation
Insertion Loss
Isolation
Insertion Loss
Isolation
1
1
1
Shutdown mode
Note 1: “1” = 1.8 V; “0” = 0 V. Any state other than that described in this Table places the switch into an undefined state. An undefined state will not damage the device.
Insertion loss in the V1/2/3 = 110 state is 3 dB lower than typical insertion loss with only one arm “on.”
Table 5. Isolation Matrix (1 of 2)
“On” Port
Isolation
(dB)
Frequency
(GHz)
RF1
RF2
RF3
RF4
RF5
Antenna-to-Port
RF1
1.0
-48
–40
–42
–39
RF1
2.0
-40
–32
–35
–30
RF1
2.7
-36
–28
–32
–26
RF2
1.0
–46
-40
–40
–36
RF2
2.0
–39
–34
–32
–30
RF2
2.7
–35
–31
–28
–27
RF3
1.0
–38
–47
–42
–42
RF3
2.0
–31
–39
–35
–30
RF3
2.7
–28
–35
–32
–26
RF4
1.0
–45
–38
–41
–37
RF4
2.0
–38
–31
–34
–30
RF4
2.7
–35
–28
–31
–27
RF5
1.0
–48
–47
–38
–43
RF5
2.0
–36
–39
–30
–36
RF5
2.7
–31
–36
–27
–32
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201704G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 2, 2014
5
DATA SHEET • SKY13415-485LF: SP5T SWITCH
Table 5. Isolation Matrix (2 of 2)
“On” Port
Isolation
(dB)
Frequency
(GHz)
RF1
RF2
RF3
RF4
RF5
Port-to-Port
RF1
1.0
–53
–31
–52
–45
RF1
2.0
–43
–25
–44
–35
RF1
2.7
–39
–22
–40
–30
RF2
1.0
–54
–48
–31
–40
RF2
2.0
–42
–41
–25
–35
RF2
2.7
–38
–37
–22
–32
RF3
1.0
–31
–56
–53
–33
RF3
2.0
–24
–45
–44
–26
RF3
2.7
–21
–40
–40
–23
RF4
1.0
–54
–30
–48
–41
RF4
2.0
–43
–24
–41
–35
RF4
2.7
–39
–21
–38
–32
RF5
1.0
–37
–55
–30
–55
RF5
2.0
–30
–44
–24
–44
RF5
2.7
–27
–40
–21
–39
Evaluation Board Description
Package and Handling Information
The SKY13415-485LF Evaluation Board is used to test the
performance of the SKY13415-485LF SP5T Switch. An Evaluation
Board schematic diagram is provided in Figure 3. An assembly
drawing for the Evaluation Board is shown in Figure 4.
Instructions on the shipping container label regarding exposure to
moisture after the container seal is broken must be followed.
Otherwise, problems related to moisture absorption may occur
when the part is subjected to high temperature during solder
assembly.
Package Dimensions
The PCB layout footprint for the SKY13415-485LF is provided in
Figure 5. Typical case markings are shown in Figure 6. Package
dimensions for the 14-pin QFN are shown in Figure 7, and tape
and reel dimensions are provided in Figure 8.
The SKY13415-485LF is rated to Moisture Sensitivity Level 1
(MSL1) at 260 C. It can be used for lead or lead-free soldering.
For additional information, refer to the Skyworks Application Note,
Solder Reflow Information, document number 200164.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
6
May 2, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201704G
DATA SHEET • SKY13415-485LF: SP5T SWITCH
RF Output
Port 3
RF Output
Port 1
N/C
1
12
ANT
RF Output
Port 5
13
N/C
14
Antenna
×
×
RF5
N/C
RF3
RF4
RF1
RF2
VDD
N/C
2
×
10
3
4
DC Control
Voltage 3
DC Control
Voltage 2
5
×
V1
V2
6
RF Output
Port 4
RF Output
Port 2
9
8
V3
DC Power
11
DC Control
Voltage 1
7
S2670
Figure 3. SKY13415-485LF Evaluation Board Schematic
RF3
RF1
RF5
N/C
GND
VDD
V3
V2
V1
N/C
ANT
N/C
RF2
RF4
N/C
S2671
Figure 4. SKY13415-485LF Evaluation Board Assembly Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201704G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 2, 2014
7
DATA SHEET • SKY13415-485LF: SP5T SWITCH
14X 0.755
Pin 14
14X 0.395
R0.125
Pin 1 Indicator
Pin 1
14X 0.200
6X 0.450 Pitch
2X 0.500
Exposed Soldering
Area
Package Outline
4X 0.400 Pitch
2X 0.500
S2700
All measurements in millimeters
Figure 5. SKY13415-485LF PCB Layout Footprint
(Top View)
Pin 1
Indicator
Skyworks Part #
Figure 6. Typical Part Markings
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
8
May 2, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201704G
DATA SHEET • SKY13415-485LF: SP5T SWITCH
2.00
Seating
Plane
–C–
–A–
0.02 +0.03/–0.02
–B–
Pin 1
Indicator
(0.500) 8X 0.845
R0.125
Pin 1 Indicator
See Detail A
12
14
1
11
6X 0.845
4X 0.225
2.00
4X 0.675
4
8
0.05 C
2X
0.120 Ref.
0.55 ± 0.05
2X
0.05 C
7
Exposed Pad
5
14X 0.065
14X 3
0.05 C
0.05 C
1 ± 0.1
(0.500)
4X 0.400 Min.
14X 0.255
1 ± 0.1
Top View
Side View
Bottom View
0.2 ± 0.05
0.18 ± 0.05
5
0.10 M C A B
All measurements are in millimeters.
Dimensioning and tolerancing according to ASME Y14.5M-1994.
Coplanarity applies to the terminals and all other bottom surface metalization.
Dimension applies to metalized terminal. If the terminal has a radius on its end,
the width dimension should not be measured in that radius area.
Detail A
Scale: 100X
3X This Rotation
3X Rotated 180°
4X Rotated 90° CW
4X Rotated 90° CCW
S2799a
Figure 7. SKY13415-485LF 14-Pin QFN Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201704G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 2, 2014
9
DATA SHEET • SKY13415-485LF: SP5T SWITCH
∅1.50+ 0.10/–0.00
0.30 ± 0.05 (T)
Pin #1
4.00 ± 0.10
2.00 ± 0.05
4.00 (see Note 4)
1.75 ± 0.10
2.30 (Bo)
A
B
1.00 (Ko)
2.30 (Ao)
8.00 +0.30/–0.10
A
3.50 ± 0.05
B
∅1.00 Min.
R0.30 Typ.
B
Notes:
1. Carrier tape: black conductive polystyrene.
2. Cover tape material: transparent conductive HSA.
3. Cover tape size: 5.40 mm width.
4. Ten sprocket hole pitch cumulative tolerance = ±0.20 mm.
5. ESD surface resistivity is ≤1 x 108 Ohms/square per EIA, JEDEC
tape and reel specification.
6. Ao and Bo measurement point to be 0.30 mm from bottom pocket.
7. All measurements are in millimeters.
A
Figure 8. SKY13415-485LF Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
10
May 2, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201704G
S1601
DATA SHEET • SKY13415-485LF: SP5T SWITCH
Ordering Information
Model Name
SKY13415-485LF: 0.1 to 3.0 GHz SP5T Switch
Manufacturing Part Number
SKY13415-485LF
Evaluation Board Part Number
SKY13415-485LF-EVB
Copyright © 2011-2014 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands
and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com,
are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201704G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 2, 2014
11