MICRF211 3V, QwikRadio® 433.92 MHz Receiver General Description Features -2 The MICRF211 is a general purpose, 3V QwikRadio • –110dBm sensitivity, 1kbps and BER 10 Receiver that operates at 433.92MHz with typical • Image rejection mixer sensitivity of –110dBm. • Frequency from 380MHz to 450MHz The MICRF211 functions as a super-heterodyne • Low power, 6.0mA @ 433.92MHz, continuous on receiver for OOK and ASK modulation up to 10kbps. data rates to 10kbps (Manchester Encoded) The down-conversion mixer also provides image • Analog RSSI output rejection. All post-detection data filtering is provided on • No IF filter required the MICRF211. Any one-of-four filter bandwidths may be selected externally by the user in binary steps, from • Excellent selectivity and noise rejection 1.25kHz to 10kHz. The user need only configure the • Low external part count device with a set of easily determined values, based upon data rate, code modulation format, and desired duty-cycle operation. Datasheets and support documentation are available on Micrel’s website at: www.micrel.com. _______________________________________________________________________________________________ Typical Application 433.92 MHz, 1kHz Baud Rate Example QwikRadio is a registered trademark of Micrel, Inc. Certain of the QwikRadio ICs were developed under a development agreement with AIT of Orlando, FL. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com August 19, 2015 Revision 2.0 (408) 944-0800 Micrel MICRF211 Ordering Information Part Number Temperature Range Package MICRF211AYQS –40° to +105°C 16-Pin QSOP Pin Configuration MICRF211AYQS Pin Description 16-Pin QSOP Pin Name 1 RO1 2 GNDRF 3 ANT 4 GNDRF 5 VDD 6 SQ 7 SEL0 Logic control input with active internal pull-up. Used in conjunction with SEL1 to control the demodulator low pass filter bandwidth. (See filter table for SEL0 and SEL1 in application section) 8 SHDN Shutdown logic control input. Active internal pull-up. 9 GND Negative supply connection for all chip functions except RF input. 10 DO 11 SEL1 Logic control input with active internal pull-up. Used in conjunction with SEL0 to control the demodulator low pass filter bandwidth. (See filter table for SEL0 and SEL1 in application section) 12 CTH Demodulation threshold voltage integration capacitor connection. Tie an external capacitor across CTH pin and GND to set the settling time for the demodulation data slicing level. Values above 1nF are recommended and should be optimized for data rate and data profile. 13 CAGC AGC filter capacitor connection. CAGC capacitor, normally greater than 0.47µF, is connected from this pin to GND 14 RSSI Received signal strength indication output. Output is from a buffer with 200Ω typical output impedance. 15 NC 16 RO2 August 19, 2015 Pin Function Reference resonator input connection to Colpitts oscillator stage. May also be driven by external reference signal of 1.5V p-p amplitude maximum. Negative supply connection associated with ANT RF input. RF signal input from antenna. Internally AC coupled. It is recommended that a matching network with an inductor -to-RF ground is used to improve ESD protection. Negative supply connection associated with ANT RF input. Positive supply connection for all chip functions. Squelch control logic input with an active internal pull-up when not shut down. Demodulated data output. Not Connected (Connect to Ground) Reference resonator input connection to Colpitts oscillator stage, 7pF, in parallel with low resistance MOS switch-to-GND, during normal operation. Driven by startup excitation circuit during the internal startup control sequence. 2 Revision 2.0 (408) 944-0800 Micrel MICRF211 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VDD) .................................................+5V Input Voltage ............................................................. +5V Junction Temperature ......................................... +150ºC Lead Temperature (soldering, 10sec.) .................. 260°C Storage Temperature (TS) ..................... -65ºC to +150°C Maximum Receiver Input Power ........................+10dBm (3) ESD Rating ................................................... 2kV CDM ................................................... 200V HBM ................................. 100V Machine Model Supply Voltage (VDD) ..............................+3.0V to +3.6V Ambient Temperature (TA) ................. –40°C to +105°C Input Voltage (VIN) ....................................... 3.6V (max.) Maximum Input RF Power................................ –20dBm Electrical Characteristics(4) Specifications apply for 3.0V < VDD < 3.6V, VSS = 0V, CAGC = 4.7µF, CTH = 0.1µF, fRX = 433.92MHz, unless otherwise noted. Bold values indicate –40°C – TA – 105°C. 1kbps data rate (Manchester encoded), reference oscillator frequency = 13.52127MHz. Symbol Parameter Condition Min ISS Operating Supply Current Continuous Operation, fRX = 433.92MHz ISHUT Shut down Current Typ Max Units 6.0 mA 0.5 µA 20 dB 1.2 MHz RF/IF Section Image Rejection st 1 IF Center Frequency fRX = 433.92MHz Receiver Sensitivity @ 1kbps fRX = 433.92MHz (matched to 50Ω) -2 BER=10 -110 dBm IF Bandwidth fRX = 433.92MHz 330 kHz Antenna Input Impedance fRX = 433.92MHz 19 – j174 Ω Receive Modulation Duty Cycle Note 5 AGC Attack / Decay Ratio tATTACK / tDECAY AGC pin leakage current TA = 25ºC TA = +105ºC ±2 ± 800 nA nA RFIN @ -40dBm 1.15 V RFIN @ -100dBm 1.70 V 13.52127 MHz 300 kΩ AGC Dynamic Range 20 80 % 0.1 Reference Oscillator Reference Oscillator Frequency fRX = 433.92MHz Crystal Load Cap = 10pF Reference Oscillator Input Impedance Reference Oscillator Input Range Reference Oscillator Source Current August 19, 2015 0.2 V(REFOSC) = 0V 1.5 3.5 3 Vp-p µA Revision 2.0 (408) 944-0800 Micrel MICRF211 Electrical Characteristics(4) Specifications apply for 3.0V < VDD < 3.6V, VSS = 0V, CAGC = 4.7µF, CTH = 0.1µF, fRX = 433.92MHz, unless otherwise noted. Bold values indicate –40°C – TA – 105°C. 1kbps data rate (Manchester encoded), reference oscillator frequency = 13.52127MHz. Demodulator Symbol Parameter Condition Min CTH Source Impedance FREFOSC = 13.52127MHz CTH Leakage Current TA = 25ºC TA = +105ºC Demodulator Filter Bandwidth @ 434MHz Programmable, see application section Typ Max Units 120 kΩ ±2 ± 800 nA nA 1625 13000 Hz Digital / Control Functions 260 600 µA 2 µsec 0.4 to 2 V 25 mV/dB RSSI Output Current 400 µA RSSI Output Impedance 200 Ω 0.3 sec DO pin output current Output rise and fall times As output source @ 0.8 Vdd sink @ 0.2 Vdd CI = 15pF, pin DO, 10-90% RSSI RSSI DC Output Voltage Range RSSI response slope RSSI Response Time -110dBm to -40dBm 50% data duty cycle, input power to Antenna = -20dBm Notes: 1. Exceeding the absolute maximum ratings may damage the device. 2. The device is not guaranteed to function outside its operating ratings. 3. Device is ESD sensitive. Use appropriate ESD precautions. Exceeding the absolute maximum rating may damage the device. 4. Sensitivity is defined as the average signal level measured at the input necessary to achieve 10-2 BER (bit error rate). The input signal is defined as a return-to-zero (RZ) waveform with 50% average duty cycle (Manchester encoded) at a data rate of 1kbps. 5. When data burst does not contain preamble, duty cycle is defined as total duty cycle, including any “quiet” time between data bursts. When data bursts contain preamble sufficient to charge the slice level on capacitor Cth, then duty cycle is the effective duty cycle of the burst alone. [For example, 100msec burst with 50% duty cycle, and 100msec “quiet” time between bursts. If burst includes preamble, duty cycle is Ton/(Ton+toff)= 50%; without preamble, duty cycle is Ton/(Ton+ Toff + Tquiet) = 50msec/(200msec)=25%. Ton is the (Average number of 1’s/burst) × bit time, and Toff = Tburst – Ton.) August 19, 2015 4 Revision 2.0 (408) 944-0800 Micrel MICRF211 Typical Characteristics Sensitivity Graphs August 19, 2015 5 Revision 2.0 (408) 944-0800 Micrel MICRF211 Functional Diagram Figure 1. Simplified Block Diagram. is set to 32 times the crystal reference frequency via a phase-locked loop synthesizer with a fully integrated loop filter. Functional Description Figure 1. Simplified Block Diagram that illustrates the basic structure of the MICRF211. It is made of three sub-blocks; Image Rejection UHF Down-converter, the OOK Demodulator, and Reference and Control Logics. Outside the device, the MICRF211 requires only three components to operate: two capacitors (CTH, and CAGC) and the reference frequency device, usually a quartz crystal. An additional five components may be used to improve performance. These are: power supply decoupling capacitor, two components for the matching network, and two components for the pre-selector band pass filter. Image Reject Filter and Band-Pass Filter The IF ports of the mixer produce quadrature down converted IF signals. These IF signals are low-pass filtered to remove higher frequency products prior to the image reject filter where they are combined to reject the image frequencies. The IF signal then passes through a third order band pass filter. The IF center frequency is 1.2MHz. The IF BW is 330kHz @ 433.92MHz, and this varies with RF operating frequency. The IF BW can be calculated via direct scaling: Receiver Operation Operating Freq (MHz) 433.92 BW IF = BW [email protected] MHz × LNA The RF input signal is AC-coupled into the gate circuit of the grounded source LNA input stage. The LNA is a Cascoded NMOS. These filters are fully integrated inside the MICRF211. After filtering, four active gain controlled amplifier stages enhance the IF signal to proper level for demodulation. Mixers and Synthesizer The LO ports of the Mixers are driven by quadrature local oscillator outputs from the synthesizer block. The local oscillator signal from the synthesizer is placed on the low side of the desired RF signal to allow suppression of the image frequency at twice the IF frequency below the wanted signal. The local oscillator August 19, 2015 OOK Demodulator The demodulator section is comprised of detector, programmable low pass filter, slicer, and AGC comparator. Detector and Programmable Low-Pass Filter The demodulation starts with the detector removing the 6 Revision 2.0 (408) 944-0800 Micrel MICRF211 carrier from the IF signal. Post detection, the signal becomes base band information. The programmable low-pass filter further enhances the base band information. There are four programmable low-pass filter BW settings: 1625Hz, 3250Hz, 6500Hz, 13000Hz for 433.92MHz operation. Low pass filter BW will vary with RF Operating Frequency. Filter BW values can be easily calculated by direct scaling. See equation below for filter BW calculation: When the output signal is less than 750mV thresh-hold, 1.5µA current is sourced into the external CAGC capacitor. When the output signal is greater than 750mV, a 15µA current sink discharges the CAGC capacitor. The voltage developed on the CAGC capacitor acts to adjust the gain of the mixer and the IF amplifier to compensate for RF input signal level variation. Reference Control There are 2 components in Reference Control subblock: 1) Reference Oscillator and 2) Control Logic through parallel Inputs: SEL0, SEL1, SHDN Operating Freq (MHz) BW Operating Freq = BW @433.92MHz* 433.92 It is very important to choose the filter setting that best fits the intended data rate to minimize data distortion. Demod BW is set at 13000Hz @ 433.92MHz as default (assuming both SEL0 and SEL1 pins are floating). The low pass filter can be hardware set by external pins SEL0 and SEL1. SEL0 SEL1 0 0 1625Hz 1 0 3250Hz 0 1 6500Hz 1 1 13000Hz Reference Oscillator Demod BW (@ 434MHz) - default Table 1: Demodulation BW Selection Slicer, Slicing Level and Squelch The signal prior to slicer is still linear demodulated AM. Data slicer converts this signal into digital “1”s and “0”s by comparing with the threshold voltage built up on the CTH capacitor. This threshold is determined by detecting the positive and negative peaks of the data signal and storing the mean value. Slicing threshold default is 50%. After the slicer the signal is now digital OOK data. During long periods of “0”s or no data period, threshold voltage on the CTH capacitor may be very low. Large random noise spikes during this time may cause erroneous “1”s at DO pin. Squelch pin when pull down low will suppress these errors. Figure 2: Reference Oscillator Circuit The reference oscillator in the MICRF211 (Figure 2) uses a basic Colpitts crystal oscillator configuration with MOS transconductor to provide negative resistance. All capacitors shown in Figure 2 are integrated inside MICRF211. R01 and R02 are external pins of MICRF211. User only needs to connect reference oscillation crystal. Reference oscillator crystal frequency can be calculated: FREF OSC = FRF/(32 + 1.1/12) For 433.92 MHz, FREF OSC = 13.52127 MHz. To operate the MICRF211 with minimum offset, crystal frequencies should be specified with 10pF loading capacitance. AGC Comparator The AGC comparator monitors the signal amplitude from the output of the programmable low-pass filter. August 19, 2015 7 Revision 2.0 (408) 944-0800 Micrel MICRF211 Application Information Figure 3 – QR211HE1 Application Example, 433.92 MHz The MICRF211 can be fully tested by using one of many evaluation boards designed at Micrel for this device. As an entry level, the QR211HE1 (Figure 3) offers a good start for most applications. It has a helical PCB antenna with its matching network, a band-pass-filter front-end as a pre-selector filter, matching network and the minimum components required to make the device work, which are a crystal, Cagc, and Cth capacitors. By removing the matching network of the helical PCB antenna (C9 and L3), a whip antenna (ANT2) or a RF connector (J2) can be used instead. Figure 3 shows the entire schematic of it for 433.92MHz. Other frequencies can be used and the values needed are in the tables below. Capacitor C9 and inductor L3 are the passive elements for the helical PCB matching network. A tight tolerance is recommended for these devices, like 2% for the inductor and 0.1pF for the capacitor. PCB variations may require different values and optimization. Table 2 shows the matching elements for the device frequency range. For additional information look for Small PCB Antennas for Micrel RF Products application note. Freq (MHz) C9 (pF) L3(nH) 390.0 1.2 43 418.0 1.2 36 433.92 1.5 30 which reduces the receiver performance. It is calculated by the parallel resonance equation f = 1/(2×PI×(SQRT L1×C8)). Table 3 shows the most used frequency values. Freq (MHz) L1(nH) 390.0 6.8 24 418.0 6.0 24 433.92 5.6 24 Table 3. Band-Pass-Filter Front-End Values There is no need for the band-pass-filter front-end for applications where it is proven that the outside band noise does not cause a problem. The MICRF211 has image reject mixers which improve significantly the selectivity and rejection of outside band noise. Capacitor C3 and inductor L2 form the L-shape matching network. The capacitor provides additional attenuation for low frequency outside band noise and the inductor provides additional ESD protection for the antenna pin. Two methods can be used to find these values, which are matched close to 50Ω. One method is done by calculating the values using the equations below and another by using a Smith chart. The latter is made easier by using software that plots the values of the components C8 and L1, like WinSmith by Noble Publishing. To calculate the matching values, one needs to know the input impedance of the device. Table 4 shows the input impedance of the MICRF211 and suggested matching values for the most used frequencies. These suggested values may be different if the layout is not exactly the same as the one made here. Table 2. Matching Values for the Helical PCB Antenna To use another antenna, like the whip kind, remove C9 and place the whip antenna in the hole provided in the PCB. Also, a RF signal can be injected there. L1 and C8 form the pass-band-filter front-end. Its purpose is to attenuate undesired outside band noise August 19, 2015 C8 (pF) 8 Revision 2.0 (408) 944-0800 Micrel Freq (MHz) MICRF211 C3 (pF) L2(nH) Z device (Ω) 1.5 47 22.5 – j198.5 418.0 1.5 43 21.4 – j186.1 433.92 1.5 39 18.6 – j174.2 390.0 Second, we plot the shunt inductor (39nH) and the series capacitor (1.5pF) for the desired input impedance (Figure 5). We can see the matching leading to the center of the Smith Chart or close to 50Ω. Table 4: matching values for the most used frequencies For the frequency of 433.92MHz, the input impedance is Z = 18.6 – j174.2Ω, then the matching components are calculated by, Equivalent parallel = B = 1/Z = 0.606 + j5.68 msiemens Rp = 1 / Re (B); Xp = 1 / Im (B) Rp = 1.65kΩ; Xp = 176.2Ω Q = SQRT (Rp/50 + 1) Q = 5.831 Xm = Rp / Q Xm = 282.98Ω Resonance Method For L-shape Matching Network Lc = Xp / (2×Pi×f); Lp = Xm / (2×Pi×f) L2 = (Lc×Lp) / (Lc + Lp); C3 = 1 / (2×Pi×f×Xm) L2 = 39.8nH C3 = 1.3pF Doing the same calculation example with the Smith Chart, it would appear as follows, First, we plot the input impedance of the device, (Z = 18.6 – j174.2)Ω @ 433.92MHz.(Figure 4). Figure 5. Plotting the Shunt Inductor and Series Capacitor. Figure 4: device’s input impedance, Z = 18.6 – j174.2Ω August 19, 2015 9 Revision 2.0 (408) 944-0800 Micrel MICRF211 Crystal Y1 or Y1A (SMT or leaded respectively) is the reference clock for all the device internal circuits. Crystal characteristics of 10pF load capacitance, 30ppm, ESR < 50Ω, -40ºC to +105ºC temperature range are desired. Table 5 shows the crystal frequencies and one of Micrel’s approved crystal manufacturers (www.hib.com.br). The oscillator of the MICRF211 is a Colpitts type. It is very sensitive to stray capacitance loads. Thus, very good care must be taken when laying out the printed circuit board. Avoid long traces and ground plane on the top layer close to the REFOSC pins RO1 and RO2. When care is not taken in the layout, and crystals from other vendors are used, the oscillator may take longer times to start as well as the time to good data in the DO pin to show up. In some cases, if the stray capacitance is too high (> 20pF), the oscillator may not start at all. The crystal frequency is calculated by REFOSC = RF Carrier/(32+(1.1/12)). The local oscillator is low side Image Frequency Desired Signal -fLO f (MHz) Figure 6. Low Side Injection Local Oscillator. REFOSC (MHz) Carrier (MHz) HIB Part Number 12.15269 390.0 SA-12.152690-F-10-H-30-30-X 13.02519 418.0 SA-13.025190-F-10-H-30-30-X 13.52127 August 19, 2015 injection (32 × 13.52127MHz = 432.68MHz), that is, its frequency is below the RF carrier frequency and the image frequency is below the LO frequency. See Figure 6. The product of the incoming RF signal and local oscillator signal will yield the IF frequency, which will be demodulated by the detector of the device. 433.92 SA-13.521270-F-10-H-30-30-X Table 5. Crystal Frequency and Vendor Part Number. 10 Revision 2.0 (408) 944-0800 Micrel MICRF211 JP1 and JP2 are the bandwidth selection for the demodulator bandwidth. To set it correctly, it is necessary to know the shortest pulse width of the encoded data sent in the transmitter. Like in the example of the data profile in the figure 7 below, PW2 is shorter than PW1, so PW2 should be used for the demodulator bandwidth calculation which is found by 0.65/shortest pulse width. After this value is found, the setting should be done according to Table 6. For example, if the pulse period is 100µsec, 50% duty cycle, the pulse width will be 50µsec (PW = (100µsec × 50%) / 100). So, a bandwidth of 13kHz would be necessary (0.65 / 50µsec). However, if this data stream had a pulse period with 20% duty cycle, the bandwidth required would be 32.5kHz (0.65 / 20µsec), which exceeds the maximum bandwidth of the demodulator circuit. If one tries to exceed the maximum bandwidth, the pulse would appear stretched or wider. SEL0 JP1 SEL1 JP2 Demod. BW (hertz) Shortest Pulse (µsec) SEL0 JP1 SEL1 JP2 Demod. Shortest Pulse (µsec) BW (hertz) Maximum baud rate for 50% Duty Cycle (Hertz) Short Short 1460 445 1123 Open Short 2921 223 2246 Short Open 5842 111 4493 Open Open 11684 56 8987 Table 8. JP1 and JP2 setting, 390.0 MHz. Capacitors C6 and C4, CTH and CAGC respectively provide time base reference for the data pattern received. These capacitors are selected according to data profile, pulse duty cycle, dead time between two received data packets, and if the data pattern has or does not have a preamble. See Figure 7, example of a data profile. Maximum baud rate for 50% Duty Cycle (hertz) PW1 PW2 Preamble Header 1 2 3 4 5 6 7 8 9 10 Short Short 1625 400 1250 Open Short 3250 200 2500 PW2 = Narrowest pulse width Short Open 6500 100 5000 t1 & t2 = data period Open Open 13000 50 10000 t1 t2 Figure 7. Example of a Data Profile. Table 6. JP1 and JP2 setting, 433.92 MHz. For best results the capacitors should always be optimized for the data pattern used. As the baud rate increases, the capacitor values decrease. Table 9 shows suggested values for Manchester Encoded data, 50% duty cycle. Other frequencies will have different demodulator bandwidth limits, which are derived from the reference oscillator frequency. Table 7 and Table 8 below shows the limits for the other two most used frequencies. SEL0 JP1 SEL1 JP2 Demod. Short BW (hertz) Shortest Pulse (µsec) Maximum baud rate for 50% Duty Cycle (hertz) SEL0 JP1 SEL1 JP2 Demod. BW (hertz) Cth Cagc Short 1565 416 1204 Short Short 1625 100nF 4.7µF Open Short 3130 208 2408 Open Short 3250 47nF 2.2µF Short Open 6261 104 4816 Short Open 6500 22nF 1µF 9633 Open Open 13000 10nF 0.47µF Open Open 12523 52 Table 9. Suggested CTH and CAGC Values. Table 7. JP1 and JP2 setting, 418.0 MHz. JP3 is a jumper used to configure the digital squelch function. When it is high, there is no squelch applied to the digital circuits and the DO (data out) pin has a hash signal. When the pin is low, the DO pin activity is August 19, 2015 11 Revision 2.0 (408) 944-0800 Micrel MICRF211 considerably reduced. It will have more or less than shown in the figure below depending on the outside band noise. The penalty for using squelch is a delay in getting a good signal in the DO pin, that is, it takes longer for the data to show up. The delay is dependent upon many factors such as RF signal intensity, data profile, data rate, CTH and CAGC capacitor values, and outside band noise. See Figure 8 and Figure 9 below. which form a voltage divider for the AGC pin. One can force a voltage in this AGC pin to purposely decrease the device sensitivity. Special care is needed when doing this operation, as an external control of the AGC voltage may vary from lot to lot and may not work the same for several devices. Three other pins are worthy of comment. They are the DO, RSSI, and shut down pins. The DO pin has a driving capability of 0.4mA. This is good enough for most of the logic family ICs in the market today. The RSSI pin provides a transfer function of the RF signal intensity vs voltage. It is very useful to determine the signal to noise ratio of the RF link, crude range estimate from the transmitter source and AM demodulation, which requires a low CAGC capacitor value. The shut down pin (SHDN) is useful to save energy. When its level close to VDD (SHDN = 1), the device is not in operation. Its DC current consumption is less than 1µA (do not forget to remove R3). When toggling from high to low, there will be a time required for the device to come to steady state mode, and a time for data to show up in the DO pin. This time will be dependent upon many things such as temperature, crystal used, and if the there is an external oscillator with faster startup time. Normally, with the crystal vendors suggested, the data will show up in the DO pin around 1msec time, and 2msec over the temperature range of the device. When using an external oscillator or reference oscillator signal, the time is reduced considerably and can be around 140µsec. See Figures Figure 10 and 11. Figure 8. Data Out Pin with No Squelch (SQ = 1). Figure 9. Data Out Pin with Squelch (SQ = 0). Other components used are C5, which is a decoupling capacitor for the Vdd line, R4 reserved for future use and not needed for the evaluation board, R3 for the shutdown pin (SHDN = 0, device is operation), which can be removed if that pin is connected to a microcontroller or an external switch, R1 and R2 August 19, 2015 Figure 10: Time-to-Good Data After Shut Down Cycle, Room Temperature. 12 Revision 2.0 (408) 944-0800 Micrel MICRF211 To prevent the erroneous startup, a simple RC network is recommended. The 10Ω resistor and the 4.7µF capacitor provide a delay of about 200µs between VDD and SHDN during power up, thus ensuring the part enters the shutdown stage before the part is actually turned on. The 2.2µF capacitor bootstraps the voltage on SHDN, ensuring that SHDN voltage leads the supply voltage on VDD during power up. This gives the POR circuit time to set internal register bits. The SHDN pin can be brought low to turn the chip on once the initialization is completed. The 2.2µF and 100kΩ network form a RC delay of about 200ms before the SHDN pin is brought to low again. The 100kΩ resistor discharges the SHDN pin to turn the chip on. Figure 11. Time to Good Data, External Oscillator, Room Temperature. Important Note A few customers have reported that some MICRF211 receiver do not start up correctly. When the issue occurs, DO either chatters or stays at low voltage level. An unusual operating current is observed and the part cannot receive or demodulate data even when a strong OOK signal is present. Micrel has confirmed that this is the symptom of incorrect power on reset (POR) of internal register bits. The MICRF211 is designed to start up in shutdown mode (SHDN pin must be in logic high during Vdd ramp up). When the SHDN pin is tied to GND, and if the supply is ramped up slowly, a “test bus pull down” circuit may be activated. Once the chip enters this mode, the POR does not have the chance to set register bits (and hence operating modes) correctly. The test bus pull down acts on the SHDN pin, and can be illustrated in the following diagram. VDD pin SHDN Pin The suggestion provided above will generally serve to prevent the startup issue from happening to the MICRF211 series ASK receiver. However, exact values of the RC network depend on the ramp rate of the supply voltage, and should be determined on a case-by-case basis. 3.3V MICRF2XX 10 ohm (Vdd) pin MICRF2XX Bias control & POR 4.7uF 2.2uF Test Mode Circuits Change the SHDN pin and Vdd pin connections to Test Bus (SHDN) pin (SHDN) pin 100K This device turns on, preventing POR from setting operating modes correctly August 19, 2015 13 Revision 2.0 (408) 944-0800 Micrel MICRF211 PCB Considerations and Layout Figures 12 to 17 below show some of the printed circuit layers for the QR211HE1 board. Use the Gerber files provided (downloadable from Micrel Website) which have the remaining layers needed to fabricate this board. When copying or making your own boards, make traces as short as possible. Long traces alter the matching network and the values suggested are no longer valid. Suggested Matching Values may vary due to PCB variations. A PCB trace 100 mills (2.5mm) long has about 1.1nH inductance. Optimization should always be done with exhaustive range tests. Make individual ground connections to the ground plane with a Via for each ground connection. Do not share Vias with ground connections. Each ground connection = 1 via or more vias. Ground plane must be solid and possibly without interruptions. Avoid ground plane on top next to the matching elements. It normally adds additional stray capacitance which changes the matching. Do not use phenolic material, only FR4 or better materials. Phenolic material is conductive above 200MHz. RF path should be as straight as possible avoiding loops and unnecessary turns. Separate ground and VDD lines from other circuits (microcontroller, etc). Known sources of noise should be laid out as far as possible from the RF circuits. Avoid thick traces, the higher the frequency, the thinner the trace should be in order to minimize losses in the RF path. Figure 12. QR211HE1 Top Layer. Figure 13. QR211HE1 Bottom Layer, Mirror Image. August 19, 2015 14 Revision 2.0 (408) 944-0800 Micrel MICRF211 Figure 14. QR211HE1 Top Silkscreen Layer. Figure 15. QR211HE1 Bottom Silkscreen Layer, Mirror Image. Figure 16: QR211HE1 Dimensions. August 19, 2015 15 Revision 2.0 (408) 944-0800 Micrel MICRF211 QR211HE1 Bill of Materials, 433.92 MHz Item Part Number Manufacturer ANT1 Description Qty. Helical PCB Antenna Pattern ANT2 (np)50-ohm Ant 168mm 20 AWG, rigid wire 1 1 C3,C9 MuRata 1.5pF , 0402/0603 2 C4 Murata / Vishay 0.1µF, 0402/0603 1 C6,C5 Murata / Vishay 0.1µF, 0402/0603 2 C8 Murata 5.6pF, 0402/0603 1 JP1,JP 2 Vishay short, 0402, 0Ω resistor 2 open, 0402, not placed 1 J2 (np) not placed 1 J3 CON6 1 JP3 L1 Coilcraft / Murata / ACT1 24nH 5%, 0402/0603 1 L2 Coilcraft / Murata / ACT1 39nH 5%, 0402/0603 1 L3 Coilcraft / Murata / ACT1 30nH 2%, 0402/0603 1 (np) 0402, not placed 3 R1,R2, R4 R3 , 0402 1 Y1 HCM49 www.hib.com.br (np)13.52127MHz Crystal 1 Y1A HC49 www.hib.com.br 13.52127MHz Crystal 1 U1 Vishay MICRF211AYQS Micrel, Inc. 100kΩ ® 3V, QwikRadio 433.92 MHz Receiver 1 Table 10. QR211HE1 Bill of Materials, 433.92 MHz. August 19, 2015 16 Revision 2.0 (408) 944-0800 Micrel MICRF211 Package Information and Recommended Land Pattern(1) QSOP16 Package Type (AQS16) Note: 1. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. August 19, 2015 17 Revision 2.0 (408) 944-0800 Micrel MICRF211 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2007 Micrel, Incorporated. August 19, 2015 18 Revision 2.0 (408) 944-0800