AME2056 1A Single Cell Li-ion Battery Linear Charger

AME
AME2056
n General Description
The AME2056 is constant-current/constant-voltage linear charger IC for single cell lithium-ion batteries. The
battery charge termination voltage is fixed at 4.2V, the
charge current can be programmed an external resistor
up to 1000mA(Max.). In the trickle charge mode, the
trickle charge voltage is 2.9V that automatically terminates the charge cycle when the charge current drops to
1/10 the programmed value after the final float voltage is
reached. Other features includes Thermal Shutdown, Softstart Function, Battery temperature detector, under-voltage lockout, automatic recharge and two Status indication for Charge Status, no battery and battery failure indicators.
1A Single Cell Li-ion
Battery Linear Charger
n Applications
l Charging docks, charging cradles
l Low Cost and Small Size Chargers
l Cellular phones
n Features
Standalone Li-Ion Battery Charging
Programmable Charge Current
Charge Termination Voltage: 4.2V(Typ.)
Trickle Charge Voltage: 2.9V(Typ.)
Standby Current: 55µA(Typ.)
No Sense Resistor or Blocking Diode Required
Constant-current/constant-voltage Operation
Automatic Recharge
Battery temperature Detector
C/10 Charge Termination
Two Status indication for Charge Status, no
battery and battery failure indicators
l Soft-start Function
l Thermal Shutdown
l Available in SOP-8/PP, MSOP-8, SOT-25,
TSOT-25A and DFN-8D(2x2x0.75mm) Package
l Green Products Meet RoHS Standards
l
l
l
l
l
l
l
l
l
l
l
Rev. B.01
1
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Typical Application
VCC=5V
0.4Ω
10uF
V CC
CE
1K
BAT
Bat+
10uF
R1
1K
BatNTC
CHRG
TEMP
STDBY
PROG
R2
Li-ion
RPROG
n Functional Block Diagram
4
80%VIN
TA
-
T DIE
VCC
TTEMP
MA
5
R1
+
TEMP
1
BAT
5uA
+
145oC
-
VA
8
CE
T TEMP
-
CA
R2
+
schmitt
C1
R3
+
SHDN
1V
STDBY
+
R4
0.1V
-
6
R5
C2
CHRG
+
7
REF
1.22V
-
45%V IN
VCC
-
C3
3uA
TO
BAT
2.9V
2
PROG
GND
3
RPROG
2
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Pin Configuration
SOP-8/PP
Top View
7
8
6
5
AME2056
1
2
3
4
MSOP-8
Top View
AME2056-AZA
1. TEMP
2. PROG
3. GND
4. VCC
5. BAT
6. STDBY
7. CHRG
8. CE
8
7
6
AME2056-AQA
1. TEMP
2. PROG
3. GND
4. VCC
5. BAT
6. STDBY
7. CHRG
8. CE
5
AME2056
1
2
3
4
* Die Attach:
Conductive Epoxy
* Die Attach:
Conductive Epoxy
SOT-25/TSOT-25A
Top View
5
4
AME2056
1
2
3
DFN-8D
Top View
(2x2x0.75mm)
AME2056-AEV
1. CHRG
2. GND
3. BAT
4. VCC
5. PROG
8
Rev. B.01
6
5
AME2056
1
* Die Attach:
Conductive Epoxy
7
2
3
4
AME2056-AVA
1. TEMP
2. PROG
3. GND
4. VCC
5. BAT
6. STDBY
7. CHRG
8. CE
* Die Attach:
Conductive Epoxy
3
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Pin Description
Pin Number
4
Pin Name
Pin Description
SOP-8/PP
MSOP-8
DFN-8D
SOT-25
TSOT-25A
1
N/A
TEMP
Temperature sense Input.
2
5
PROG
Charge Current Setting and Charge Current Monitor Pin.
3
2
GND
Ground.
4
4
VCC
Input Supply Voltage
5
3
BAT
Battery Connection Pin.
6
N/A
STDBY
Charge Terminatel Status Output.
7
1
CHRG
Open-Drain Charge Status Output.
8
N/A
CE
Chip Enable Input.
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Ordering Information
AME2056 x x x x
Special Feature
Number of Pins
Package Type
Pin Configuration
Pin Configuration
A
(SOP-8/PP)
(MSOP-8)
(DFN-8D)
A
(SOT-25)
(TSOT-25A)
Rev. B.01
1. TEMP
2. PROG
3. GND
4. VCC
5. BAT
6. STDBY
7. CHRG
8. CE
Package Type
E:
Q:
V:
Z:
SOT-2X
MSOP
DFN
SOP/PP
Number of Pins
Special Feature
A: 8
V: 5
N/A: SOT-2X
K: 0.9mm max height
(for TSOT-2XA Only)
1. CHRG
2. GND
3. BAT
4. VCC
5. PROG
5
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Absolute Maximum Ratings
Parameter
Maximum
Unit
-0.3 to +6
V
-0.3 to (VCC+0.3V)
V
BAT Pin Voltage
-0.3 to +6
V
All Other Pins
0.3 to +6
V
1.2
A
Electrostatic Discharge (HBM)
2
KV
Electrostatic Discharge (MM)
200
V
Electrostatic Discharge (CDM)
1000
V
Junction Temperature
150
Input Voltage
PROG Pin Voltage
BAT Pin Current
Storage Temperature Range
o
-65 to +150
C
n Recommended Operating Conditions
Parameter
Symbol
Rating
Ambient Temperature Range
TA
-40 to +85
Junction Temperature Range
TJ
-40 to +125
VCC
4.5~5.5
Input Supply Voltage
6
Unit
o
C
V
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Thermal Information
Parameter
Package
Die Attach
Thermal Resistance*
(Junction to Case)
Thermal Resistance
(Junction to Ambient)
Symbol
Maximum
θJC
19
o
θJA
84
Internal Power Dissipation
PD
1450
Thermal Resistance*
(Junction to Case)
θJC
80
Thermal Resistance
(Junction to Ambient)
SOP-8/PP
Conductive Epoxy
206
Internal Power Dissipation
PD
625
Thermal Resistance*
(Junction to Case)
θJC
81
MSOP-8
Conductive Epoxy
θJA
260
Internal Power Dissipation
PD
400
Thermal Resistance*
(Junction to Case)
θJC
22.8
Thermal Resistance
(Junction to Ambient)
DFN-8D
Lead Temperature (Soldering, 10 sec)*
Conductive Epoxy
θJA
114
PD
880
350
C/W
mW
o
Internal Power Dissipation
Rev. B.01
Conductive Epoxy
C/W
mW
o
SOT-25
TSOT-25A
C/W
mW
o
θJA
Thermal Resistance
(Junction to Ambient)
Unit
C/W
mW
o
C
7
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Electrical Specifications
Typical values VCC=5V with typical TA = 25oC, Unless otherwise specified.
Parameter
Test Condition
Min
Typ
Max
Units
5.5
V
500.0
uA
VCC Operating Range
VCC
Supply Current
ICC
Charge mode, RPROG=1.2K
Standby Current
ISTBY
Standby mode(charge end)
55
100
uA
Shutdown Current
ISHUT
Shutdown mode
(RPROG=NC, VCC<VBAT
or VCC<VUVLO)
55
100
uA
VFLOAT
TA=25oC, IBAT=40mA
4.2
4.242
V
SOT-25 / DFN-6D / DFN-8L
800.0
mA
SOP-8/PP / MSOP-8
1000
mA
Float Voltage
Maximum Battery Current
IBAT(MAX)
4.5
4.158
IBAT1
RPROG=2.4KΩ, CC mode
VBAT=4V
450
500
550
mA
IBAT2
RPROG=1.2KΩ, CC mode
VBAT=4V
900
1000
1100
mA
IBAT3
Standby mode, VBAT=4.2V
-6
uA
IBAT4
Shutdown mode (RPROG=NC)
±2
uA
IBAT5
Sleep mode, VCC=0V
-2
uA
Trickle Charge Current
ITRIKL
VBAT<VTRIKL,RPROG=1.2KΩ
Trickle Voltage
VTRIKL
RPROG=1.2KΩ, VBAT Rising
BAT Pin Current
Trickle Voltage Hysteresis
VCC UVLO Rising Threshold
Voltage
VCC UVLO Hysteresis
8
Symbol
2.9
3
V
60
80
100
mV
3.5
3.7
3.9
V
150
200
300.0
mV
VCC:Low to High
60
100
140
mV
VCC:High to Low
5
30
50
mV
VCC:Low to High
VUVLO_HYS
VCC-VBAT lockout Threshold
Voltage
VASD
C/10 Charge Termination Current
Threshold
ITERM
mA
2.8
VTRILK_HYS
VUVLO
130
RPROG=2.4KΩ
70
mA
RPROG=1.2KΩ
130
mA
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Electrical Specifications (Contd.)
Parameter
Symbol
Test Condition
Min
Typ
Max
Units
PROG Pin Voltage
VPROG
RPROG=1.2KΩ, CC mode
0.9
1
1.1
V
CHRG Pin Output Low Voltage
VCHRG
ICHRG=5mA
0.3
0.6
V
STDBY Pin Output Low Voltage
VSTANBY
ISTDBY=5mA
0.3
0.6
V
Temp Pin High Threshold Voltage
VTEMP-H
80
82
%VCC
Temp Pin Low Threshold Voltage
VTEMP-L
Recharge Threshold Voltage
∆RECHRG
VFLOAT-VRECHRG
43
45
60
150
%VCC
200
mV
o
Temperature Limit
TLIMT
145
ON Resistance
RON
650
mΩ
Soft Start Time
tSS
400
uS
Recharge Battery Time
Battery Termination Detect Time
IPROG Pin Pull-up Current
Rev. B.01
C
tRECHRG
VBAT:High to Low
0.8
1.8
4
ms
tTERM
IBAT falling (less than ICHRG /10)
0.8
1.8
4
ms
IPROG _pull_up
2
uA
9
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Detailed Description
The AME2056 is a linear battery charger designed for single cell lithium-ion batteries. The charger has CC/CV modes
with programmable charging current. Charging current is programmed by an external resistor. No blocking diode or
external sense resistor are required.
State Diagram of A Typical Charge Cycle
A charge cycle starts when the VCC pin voltage rises above the UVLO threshold. If the voltage at BAT pin is smaller
than 2.9V, the charger is operating in trickle mode. AME2056 supplies 1/10 programmed current to the battery. When
the BAT pin voltage is greater than 2.9V, the charger enters constant-current mode. The charger supplies the programmed current to the battery. When the voltage at BAT pin approaches the float voltage (4.2V), the charger operates
in constant-voltage mode and the charging current is decreased. A charge cycle is terminated when the charging current
drops below 1/10 programmed current after the float voltage is reached. When the charging current falls below 1/10
programmed charging current for longer than TTERM (1.8ms), charging is terminated. The AME2056 enters in standby
mode.
VCC > VUVLO
& V CE = HIGH
& VCC > VBAT
YES
CC mode
VBAT < 4.2V
YES
VBAT > 2.9V
YES
Charge Current=IBAT
CHRG=Strong pull-down
STDBY=High Impedance
NO
NO
Shutdown mode
PFET OFF
CHRG=High Impedance
STDBY=HIGH Impedance
Trickle Charge mode
Charge Current = 0.1 * IBAT
NO
CHRG=Strong pull-down
ICharge < 0.1 * IBAT
NO
STDBY=High Impedance
YES
If VCC < VUVLO or
VCC < VBAT or
VCE = Low or
VTEMP > 0.8VCC or
VTEMP < 0.45VCC
Standy mode
Charge Current=0
CHRG=High Impedance
STDBY=Strong pull-down
VBAT < 4.1V
YES
10
Rev. B.01
AME
AME2056
1A Single Cell Li-ion
Battery Linear Charger
Setting Charge Current
The charging current can be programmed by a resistor connected from the PROG pin to ground. The battery charging
current is 1200 times the PROG pin flowing out current. The value of required resistor can be calculated by the following
equation:
RPROG =
1200
I CHG ( MAX )
The instantaneous charging current provided to the battery can be determined by monitoring the PROG pin voltage with
the following equation:
I CHG =
Rev. B.01
1200
R PROG
11
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
Charge status indicator
AME2056 has two status indicators CHRG and STDBY. When the charger is operating in charging status, the CHRG
and STDBY outputs enter strong pull-down and high impedance status, respectively. If the battery is in full status, the
CHRG and STDBY outputs enter high impedance and strong pull-down, respectively. When the TEMP pin voltage is
greater than VTEMP-H or lower than VTEMP-L, the CHRG and STDBY outputs enter high impedance.
When the TEMP pin is short to ground for disable the temperature protection and the battery is not to connect BAT pin,
the light of CHRG and STDBY are flicker and bright, respectively.
Charger's Status
Red Ied CHRG
Green Ied STDBY
Charging
Iight
dark
Battery in full state
dark
light
Under-voltage, battery's temperature is to high or too low,
or not connect to battery(use TEMP)
dark
dark
BAT pin is connected to 10uF capacitor, No battery mode
(TEMP=GND)
Green LED bright, Red LED flicker
Thermal Protection
The internal thermal feedback loop of AME2056 reduces the charging current when the die temperature rises above
approximately 145oC. The function protects the AME2056 from excessive temperature and allow user to push the limits
of the power handing capability without risk of damaging AME2056.
12
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
Battery Temperature Fault Monitoring
In the battery over-temperature condition, the charger will turn off the internal pass device. Two internal compared
voltage references VTEMP-H and VTEMP-L are 80%*VCC and 45%*VCC, respectively. When the voltage at TEMP pin rises
above VTEMP-H or falls below VTEMP-L, AME2056 stops charging. After the system recover from a temperature fault, the
charger will resume operation. If applications do not need the function, short the TEMP pin to ground.
The resistance of R1 and R2 are set according to the battery temperature range and the value of thermal sensitive
resistor. Assume the battery is equipped with NTC thermistor and the temperature range is TL to TH (TL<TH). The
thermistor resistance RT decreases as temperature increases from TL to TH.
The TEMP pin voltage can be calculated as:
VTEMP =
R 2 // RT
× VCC
R1 + R 2 // RT
The VTEMP decreases as the temperature increase from TL to TH.
R1 and R2 resistance are set for temperature:
0.8 × VCC = VTEMP − H =
R 2 // RTL
× VCC
R1 + R 2 // RTL
0.45 × VCC = VTEMP− L =
R 2 // RTH
× VCC at T
H
R1 + R 2 // RTH
at TL
Where RTL and RTH are the thermistor resistances at TL and TH, respectively.
The R1 and R2 can be derived as following:
R1 =
RTL × RTH × (0.8 − 0.45)
(RTL − RTH )× 0.8 × 0.45
R2 =
RTL × RTH × (0.8 − 0.45)
RTL × (0.45 − 0.8 × 0.45) − RTH × (0.8 − 0.8 × 0.45)
Rev. B.01
13
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
Under Voltage Lockout (UVLO)
The AME2056 incorporates an under voltage lockout circuit to keep the device disabled when VCC is below the UVLO
rising threshold voltage. Once the UVLO rising threshold voltage is reached, the device start-up begins. The device
operates until VCC falls below the UVLO falling threshold voltage. The typical hysteresis in the UVLO comparator is
200mV.
Manual Shutdown
The AME2056 can be shutdown by removing RPROG or pull the CE pin to the low-level voltage. A new charge cycle
is restarted by reconnecting the program resistor or pulling the CE pin to high-level voltage.
Automatic Recharge
After the charge cycle is terminated, the AME2056 monitors the BAT pin voltage by a comparator with a 1.8ms filter
time (TRECHARGE). When the BAT pin voltage drops below 4.1V, a charge cycle restarts. The function can keep the
battery near a fully charged condition.
Stability Considerations
In constant-current mode, the feedback loop includes the PROG pin. Because of the additional pole created by the
PROG pin capacitor and resistor. The equivalent capacitance on this pin must be kept to minimum for the maximum
allowed program resistor. The pole frequency created by the PROG pin should be kept above 100kHz. When the PROG
pin is loaded with a capacitor, CPROG, the following equation can be used to calculate the maximum resistance.
RPROG ≤
1
2 × π × 10 5 × C PROG
Generally, the average battery current may be of interest to the user rather than instantaneous current. A simple RC
filter can be used on the PROG pin to measure the average battery current as shown in Figure 1. A 10K resistor has been
added between the PROG pin and the filter capacitor to ensure stability.
PROG
10K
AME2056
RPROG
CHARGE
CURRENT
MONITOR
CIRCUITRY
CFILTER
GND
Figure 1
14
Rev. B.01
AME
AME2056
1A Single Cell Li-ion
Battery Linear Charger
Power Dissipation
AME2056 has thermal feedback protection to reduce the charging current in overload condition, so the power dissipation is required to consider. The power dissipation definition is:
PD = (VCC − VBAT ) × I BAT
Where PD is power dissipated, VCC is the input supply current, VBAT is the battery voltage and IBAT is the charge current.
AME2056 will automatically reduce the charging current to maintain the die temperature under 145oC approximately,
so it is not necessary to check maximum power dissipation. The ambient temperature of thermal feedback protection is:
T A = 145 o C − PD × θ JA = 145 o C − (VCC − V BA ) × θ JA
For example: AME2056 operating from a 5V power providing 0.8A to a 3.75V Li-Ion battery. The maximum ambient
temperature which the AME2056 operates in 0.8A condition can be calculated:
TA = 145o C − (5V − 3.75V ) × 0.8 A × 84 o C / W = 57 o C
The AME2056 can be used above 57oC, but the charging current will be reduced below 0.8A. The charging current can
be calculated:
I BAT =
145o C − TA
(VCC − VBAT ) × θ JA
According to the previous example with ambient temperature of 90oC, the charging current is reduced to:
I BAT =
145 o C − 90 o C
= 524mA
(5 − 3.75) × 84
Layout Consideratons
The good thermal conduction PCB layout is very important to apply to maximize the available charging current. The
thermal path is from the die to the PCB. The PCB is the heat sink. The copper pads footprint should be as large as
possible and expand out to large copper areas to spread and dissipate the heat to the ambient. Other heat source must
be considered when designing a PCB layout because they will affect overall temperature rise and maximum charging
current.
VCC Bypass Capacitor
Many types of capacitors can be used as input bypass capacitor. However, the high voltage transients can be
generated under some start-up conditions when using the self-resonant and high Q characteristics of ceramic capacitors.
Adding a 0.4Ω resistor in series with an X5R ceramic capacitors will minimize start-up voltage transients.
Rev. B.01
15
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Characterization Curve
PROG Pin Voltage vs. Supply Voltage
(Constant Current Mode)
Battery Regulation (Float) Voltage
vs. Supply Voltage
4. 24
1.025
4.235
1. 02
4. 23
4.225
VFloat (V)
VPROG(V)
1.015
1. 01
1.005
4. 22
4.215
4. 21
1
4.205
4.2
4.5
0.995
4.5
4.7
4.9
5.1
5.3
Supply Voltage (V)
5.5
4.7
Charge Current vs. Supply Voltage
1.2
1.2K
2.4K
4.9
5. 1
Supply Voltage (V)
5.3
5.5
Trickle Charge Current
vs. Supply Voltage
160
10K
1.2K
2.4K
10K
140
1
120
IBAT (mA)
IBAT (A)
0.8
0.6
0.4
100
80
60
40
0.2
20
0
4.4
4.6
4.8
5
5.2
Supply Voltage (V)
5.4
0
4.4
5.6
Battery Regulation (Float)
Charge Current
4.6
4.8
5
5.2
Supply Voltage (V)
5.6
5.4
Charge Current vs. Battery Voltage
(3.7V Li-Ior Battery)
1
4. 21
0.9
4.205
0.8
0.7
IBAT (A)
VFloat (V)
4.2
4.195
4. 19
0.5
0.4
0.3
0.2
4.185
0.1
0
4. 18
0
16
0.6
100
200
300
400
IBAT (mA)
500
600
700
2.7
3.2
3.7
VBAT (V)
4.2
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Characterization Curve (Contd.)
Trickle Charge Current vs.
Temperature
Charge Current vs. Battery Voltage
1200
25oC
0oC
129
50oC
128
127
800
IBAT (mA)
IBAT (mA)
1000
600
400
126
125
124
200
123
0
2.6
2.8
3
3.2
3.4
3.6
VBAT (V)
3.8
4
4.2
122
-50
4.4
25
2.96
4.26
2.94
4.24
2.92
2.9
75
100
4.22
4. 2
4.18
2.88
2.86
4.16
-25
0
25
50
o
Temperature ( C)
75
100
-50
-25
0
25
50
75
100
Temperature (oC)
PROG Pin Voltage vs. Temperature
Charge Current vs. Temperature
1
1200
1.2K
2.4K
10K
1000
IBAT (mA)
0.99
VPROG(V)
50
Battery Regulation (Float) Voltage vs.
Temperature
VFLOAT (V)
VTRICKLE (V)
0
Temperature (oC)
Trickle Charge Threshold vs.
Temperature
-50
-25
0.98
0.97
800
600
400
0.96
0.95
200
-50
-25
0
25
50
Temperature (oC)
Rev. B.01
75
100
0
-50
-25
0
25
50
75
Temperature (oC)
100
125
150
17
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Tape and Reel Dimension
SOP-8/PP
P0
PIN 1
W
AME
AME
P
Carrier Tape, Number of Components Per Reel and Reel Size
Package
Carrier Width (W)
Pitch (P)
Pitch (P0)
Part Per Full Reel
Reel Size
SOP-8/PP
12.0±0.1 mm
8.0±0.1 mm
4.0±0.1 mm
2500pcs
330±1 mm
MSOP-8
P0
PIN 1
W
AME
AME
P
Carrier Tape, Number of Components Per Reel and Reel Size
18
Package
Carrier Width (W)
Pitch (P)
Pitch (P0)
Part Per Full Reel
Reel Size
MSOP-8
12.0±0.1 mm
8.0±0.1 mm
4.0±0.1 mm
4000pcs
330±1 mm
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Tape and Reel Dimension (Contd.)
DFN-8D
(2mmx2mmx0.75mm)
P0
PIN 1
W
AME
AME
P
Carrier Tape, Number of Components Per Reel and Reel Size
Package
Carrier Width (W)
Pitch (P)
Pitch (P0)
Part Per Full Reel
Reel Size
DFN-8D
(2x2x0.75mm)
8.0±0.1 mm
4.0±0.1 mm
4.0±0.1 mm
3000pcs
180±1 mm
SOT-25
P0
W
AME
AME
PIN 1
P
Carrier Tape, Number of Components Per Reel and Reel Size
Package
Carrier Width (W)
Pitch (P)
Pitch (P0)
Part Per Full Reel
Reel Size
SOT-25
8.0±0.1 mm
4.0±0.1 mm
4.0±0.1 mm
3000pcs
180±1 mm
Rev. B.01
19
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Tape and Reel Dimension (Contd.)
TSOT-25A
P0
W
AME
AME
PIN 1
P
Carrier Tape, Number of Components Per Reel and Reel Size
20
Package
Carrier Width (W)
Pitch (P)
Pitch (P0)
Part Per Full Reel
Reel Size
TSOT-25A
8.0±0.1 mm
4.0±0.1 mm
4.0±0.1 mm
3000pcs
180±1 mm
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Package Dimension
SOP-8/PP
TOP VIEW
SIDE VIEW
D1
SYMBOLS
E1
E2
E
L1
C
PIN 1
D
e
Rev. B.01
INCHES
MIN
MAX
MIN
MAX
A
1.350
1.750
0.053
0.069
A1
0.000
0.250
0.000
0.010
A2
1.250
1.650
0.049
0.065
C
0.100
0.250
0.004
0.010
E
3.750
4.150
0.148
0.163
E1
5.700
6.300
0.224
0.248
L1
0.300
1.270
0.012
0.050
b
0.310
0.510
0.012
0.020
D
4.720
5.120
0.186
0.202
e
A1
FRONT VIEW
A
A2
b
MILLIMETERS
1.270 BSC
0.050 BSC
θ
0o
8o
0o
8o
E2
2.050
2.513
0.081
0.099
D1
2.150
3.402
0.085
0.134
21
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Package Dimension (Contd.)
MSOP-8
Top View
D
e1
End View
DETAIL A
TOP PKG
.
B
E1
E
BTM PKG
.
L2
B
L
L1
E1
See Detail A
SECTION B
b
b1
PIN 1
.
Front View
c
c1
WITH PLATING
A A2
A1
e
b
22
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Package Dimension (Contd.)
DFN-8D
(2mmx2mmx0.75mm)
TOP VIEW
BOTTOM VIEW
e
D
N5
N8
L
K
E
E1
D1
PIN 1 IDENTIFICATION
N4
A
A1
b
N1
A3
SYMBOLS
INCHES
MIN
MAX
MIN
MAX
A
0.700
0.800
0.028
0.031
A1
0.000
0.050
0.000
0.002
REAR VIEW
A3
0.203 REF
0.008 REF
D
1.900
2.100
0.075
0.083
E
1.900
2.100
0.075
0.083
D1
1.100
1.650
0.043
0.065
E1
0.500
0.950
0.020
0.037
K
b
e
L
Rev. B.01
MILLIMETERS
0.200 MIN
0.180
0.300
0.500 TYP
0.200
0.450
0.008 MIN
0.007
0.012
0.020 TYP
0.008
0.018
23
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Package Dimension (Contd.)
SOT-25
Top View
Side View
D
E
H
L
PIN1
S1
e
A1
A
Front View
b
Lead Pattern Drawing
1.00 BSC
0.70 BSC
Note:
2.40 BSC
1. Lead pattern unit description:
BSC: Basic. Represents theoretical exact dimension or
dimension target.
2. Dimensions in Millimeters.
3. General tolerance +0.05mm unless otherwise specified.
0.95 BSC
0.95 BSC
1.90 BSC
24
Rev. B.01
AME
1A Single Cell Li-ion
Battery Linear Charger
AME2056
n Package Dimension (Contd.)
TSOT-25A
D
b
SYMBOLS
L
0.25
E
E1
PIN1
e
c
e1
TOP VIEW
SIDE VIEW
A1
A
A2
REAR VIEW
MILLIMETERS
INCHES
MIN
MAX
MIN
MAX
A
0.700
0.900
0.028
0.035
A1
0.000
0.100
0.000
0.004
A2
0.700
0.800
0.028
0.031
b
0.350
0.500
0.014
0.020
c
0.080
0.200
0.003
0.008
D
2.820
3.020
0.111
0.119
E
1.600
1.700
0.063
0.067
E1
2.650
2.950
0.104
0.116
e
0.95 BSC
0.037 BSC
e1
1.90 BSC
0.075 BSC
L
θ
0.300
0
o
0.600
8
o
0.012
0
o
0.024
8o
Lead Pattern Drawing
1.00 BSC
0.70 BSC
2.40 BSC
Note:
1. Lead pattern unit description:
BSC: Basic. Represents theoretical exact dimension or
dimension target.
2. Dimensions in Millimeters.
3. General tolerance +0.05mm unless otherwise specified.
0.95 BSC
0.95 BSC
1.90 BSC
Rev. B.01
25
www.ame.com.tw
E-Mail: [email protected]
Life Support Policy:
These products of AME, Inc. are not authorized for use as critical components in life-support
devices or systems, without the express written approval of the president
of AME, Inc.
AME, Inc. reserves the right to make changes in the circuitry and specifications of its devices and
advises its customers to obtain the latest version of relevant information.
 AME, Inc. , August 2014
Document: A022A-DS2056-B.01
Corporate Headquarter
AME, Inc.
8F, 12 WenHu St., Nei-Hu
Taipei 114, Taiwan.
Tel: 886 2 2627-8687
Fax: 886 2 2659-2989