Part Number: XZM2DG81FS Features Package Schematics

Part Number: XZM2DG81FS
2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP
Package Schematics
Features
● Ideal for indication light on hand held products
● Long life and robust package
● Standard Package: 2,000pcs/ Reel
● MSL (Moisture Sensitivity Level): 3
● RoHS compliant
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.0039") unless otherwise noted.
3. Specifications are subject to change without notice.
Absolute Maximum Ratings
(TA=25°C)
M2DG
(InGaN)
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
30
mA
3.2
V
Forward Voltage (Max.)
(IF=20mA)
VF
4
V
Reverse Current (Max.)
(VR=5V)
IR
50
uA
λP
520*
nm
°C
Wavelength of Peak
Emission CIE127-2007*(Typ.)
(IF=20mA)
V
Wavelength of Dominant
EmissionCIE127-2007*(Typ.)
(IF=20mA)
λD
525*
nm
Spectral Line Full Width
At Half-Maximum (Typ.)
(IF=20mA)
△λ
35
nm
C
100
pF
100
mA
Power Dissipation
PD
120
mW
Operating Temperature
TA
-40 ~ +85
Tstg
-40 ~ +85
450
Capacitance (Typ.)
(VF=0V, f=1MHz)
Part
Number
XZM2DG81FS
Emitting
Color
Green
Unit
VF
iFS
Electrostatic Discharge Threshold
(HBM)
M2DG
(InGaN)
Forward Voltage (Typ.)
(IF=20mA)
Forward Current (Peak)
1/10 Duty Cycle
0.1ms Pulse Width
Storage Temperature
Operating Characteristics
(TA=25°C)
Emitting
Material
InGaN
Lens-color
Water Clear
Luminous Intensity
CIE127-2007*
(IF=20mA)
mcd
min.
typ.
700*
1195*
Wavelength
CIE127-2007*
nm
λP
Viewing
Angle
2θ 1/2
520*
110°
*Luminous intensity value and wavelength are in accordance with CIE127-2007 standards.
Feb 20,2014
XDSB5695 V2-Z
Layout: Maggie L.
P. 1/5
Part Number: XZM2DG81FS
2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED
products. Failure to comply might lead to damage and premature failure of the LED.
1.Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
2. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
Feb 20,2014
XDSB5695 V2-Z
Layout: Maggie L.
P. 2/5
Part Number: XZM2DG81FS
2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP
 M2DG
LED is recommended for reflow soldering and
soldering profile is shown below.
Feb 20,2014
XDSB5695 V2-Z
Layout: Maggie L.
P. 3/5
Part Number: XZM2DG81FS
2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP
 The device has a single mounting surface.
The device must be mounted according to
the specifications.
 Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
 Reel Dimension
 Tape Specification (Units : mm)
Remarks:
If special sorting is required (e.g. binning based on forward voltage, Luminous intensity / luminous flux, or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous intensity / luminous flux: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
Feb 20,2014
XDSB5695 V2-Z
Layout: Maggie L.
P. 4/5
Part Number: XZM2DG81FS
2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP
PACKING & LABEL SPECIFICATIONS
TERMS OF USE
1. Data presented in this document reflect statistical figures and should be treated as technical reference only.
2. Contents within this document are subject to improvement and enhancement changes without notice.
3. The product(s) in this document are designed to be operated within the electrical and environmental specifications indicated on the datasheet.
User accepts full risk and responsibility when operating the product(s) beyond their intended specifications.
4. The product(s) described in this document are intended for electronic applications in which a person’s life is not reliant upon the LED. Please
consult with a SunLED representative for special applications where the LED may have a direct impact on a person’s life.
5. The contents within this document may not be altered without prior consent by SunLED.
6. Additional technical notes are available at http://www.SunLEDusa.com/TechnicalNotes.asp
Feb 20,2014
XDSB5695 V2-Z
Layout: Maggie L.
P. 5/5