Part Number: ZMDK67S 4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP www.SunLED.com Package Schematics Features ● Ideal for indication light on hand held products ● Long life and robust package ● Standard Package: 500pcs/ Reel ● MSL (Moisture Sensitivity Level): 3 ● RoHS compliant D E Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. Absolute Maximum Ratings (TA=25°C) u S MDK (AlGaInP) L n Unit Reverse Voltage VR 5 Forward Current IF 30 mA Forward Current (Peak) 1/10 Duty Cycle 0.1ms Pulse Width iFS 185 mA Power Dissipation PD 75 Operating Temperature TA -40 ~ +85 Tstg -40 ~ +85 Storage Temperature V mW °C Operating Characteristics (TA=25°C) ZMDK67S Emitting Color Red Emitting Material AlGaInP Unit Forward Voltage (Typ.) (IF=20mA) VF 1.95 V Forward Voltage (Max.) (IF=20mA) VF 2.5 V Reverse Current (Max.) (VR=5V) IR 10 uA Wavelength of Peak Emission CIE127-2007*(Typ.) (IF=20mA) λP 645* nm Wavelength of Dominant Emission CIE127-2007*(Typ.) (IF=20mA) λD 630* nm Spectral Line Full Width At Half-Maximum (Typ.) (IF=20mA) △λ 28 nm C 35 pF Capacitance (Typ.) (VF=0V, f=1MHz) Part Number MDK (AlGaInP) Lens-color Water Clear Luminous Intensity CIE127-2007* (IF=20mA) mcd min. typ. 200 80* 427 148* Wavelength CIE127-2007* λP nm Viewing Angle 2θ 1/2 645* 120° *Luminous intensity value and wavelength are in accordance with CIE127-2007 standards. Feb 24,2014 SDSA7753 V5-X Layout: Maggie L. P. 1/5 Part Number: ZMDK67S 4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED www.SunLED.com LAMP Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. D E L n u S 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. Feb 24,2014 SDSA7753 V5-X Layout: Maggie L. P. 2/5 Part Number: ZMDK67S 4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP www.SunLED.com MDK D E L n u S LED is recommended for reflow soldering and soldering profile is shown below. Feb 24,2014 SDSA7753 V5-X Layout: Maggie L. P. 3/5 Part Number: ZMDK67S 4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP www.SunLED.com The device has a single mounting surface. The device must be mounted according to the specifications. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension L n u S Tape Specification (Units : mm) D E Remarks: If special sorting is required (e.g. binning based on forward voltage, Luminous intensity / luminous flux, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous intensity / luminous flux: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. Feb 24,2014 SDSA7753 V5-X Layout: Maggie L. P. 4/5 Part Number: ZMDK67S 4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP www.SunLED.com PACKING & LABEL SPECIFICATIONS D E L n u S TERMS OF USE 1. Data presented in this document reflect statistical figures and should be treated as technical reference only. 2. Contents within this document are subject to improvement and enhancement changes without notice. 3. The product(s) in this document are designed to be operated within the electrical and environmental specifications indicated on the datasheet. User accepts full risk and responsibility when operating the product(s) beyond their intended specifications. 4. The product(s) described in this document are intended for electronic applications in which a person’s life is not reliant upon the LED. Please consult with a SunLED representative for special applications where the LED may have a direct impact on a person’s life. 5. The contents within this document may not be altered without prior consent by SunLED. 6. Additional technical notes are available at http://www.SunLED.com/TechnicalNotes Feb 24,2014 SDSA7753 V5-X Layout: Maggie L. P. 5/5