SunLED

Part Number: ZMD20X92S-4
3.5x3.5 mm SMD CHIP LED LAMP
www.SunLED.com
Features
Applications
3.5mm X 3.5mm X 1.15mm SMD LED
Signal and symbol luminaire for orientation.
Zener diode provided for ESD Protection
Marker lights (e.g. steps, exit ways, etc).
IR-reflow compatible
Decorative and entertainment lighting.
Ideal for accent lighting
Commercial and residential lighting.
Standard Package: 2,000pcs / Reel
Automotive interior lighting.
MSL (Moisture Sensitivity Level): 2a
RoHS compliant
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
D
E
L
n
Package Schematics
u
S
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Specifications are subject to change without notice.
Dec 16, 2013
SDSA9026 V2-Z
Layout: Maggie L.
P. 1/7
Part Number: ZMD20X92S-4
3.5x3.5 mm SMD CHIP LED LAMP
www.SunLED.com
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
D
E
L
n
u
S
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise
pickup and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
Dec 16, 2013
SDSA9026 V2-Z
Layout: Maggie L.
P. 2/7
Part Number: ZMD20X92S-4
3.5x3.5 mm SMD CHIP LED LAMP
www.SunLED.com
Selection Guide
Part
Number
Emitting
Color
ZMD20X92S-4
Emitting
Material
Deep-Red
AlGaInP
Lens-color
Water Clear
Luminous Intensity
CIE127-2007*
(IF=150mA)
cd
Luminous Flux
CIE127-2007*
(IF=150mA)
lm
min.
typ.
min.
typ.
1.6*
2.09*
5*
6.3*
Viewing
Angle
2 θ 1/2 [1]
120°
Notes:
1. θ 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous flux: +/-15%.
3. LEDs are binned according to their luminous flux.
* Luminous intensity / luminous flux value is in accordance with CIE127-2007 standards.
Absolute Maximum Ratings at TA=25°C
Parameter
Symbol
Value
Unit
Power Dissipation
PD
465
mW
Junction Temperature [1]
TJ
120
°C
Top
-40 To +100
°C
Tstg
-40 To +110
°C
IF
150
mA
VR
5
V
IFM
270
mA
Rth j-a
178
°C/W
Rth j-S
78
°C/W
8000
V
Operating Temperature
D
E
L
n
u
S
Storage Temperature
DC Forward Current [1]
Reverse Voltage
Peak Forward Current [2]
Thermal Resistance [1]
(Junction/ambient)
Thermal Resistance [1]
(Junction/solder point)
Electrostatic Discharge Threshold (HBM)
Notes:
1. Rth(j-a) Results from mounting on PC board FR4 (pad size≥16 mm 2 per pad)
2. 1/10 Duty Cycle, 0.1ms Pulse Width.
Electrical / Optical Characteristics at TA=25°C
Value
Parameter
Symbol
Wavelength at peak emission CIE127-2007* IF=150mA
λpeak
660*
nm
Dominant Wavelength CIE127-2007* IF=150mA
λdom [1]
640*
nm
△λ
20
nm
VF [2]
2.5
Spectral bandwidth at 50% Φ
Forward Voltage
REL MAX
IF = 150mA
IF=150mA
Typ.
Max.
Unit
3.1
V
85
mA
Allowable Reverse Current
IR
Temperature coefficient of λpeak
IF=150mA, -10°C≤ T≤100°C
TCλpeak
0.09
nm/ °C
Temperature coefficient of λdom
IF=150mA, -10°C≤ T≤100°C
TCλdom
0.03
nm/ °C
Temperature coefficient of VF
IF=150mA, -10°C≤ T≤100°C
TCV
-2.7
mV/ °C
Notes:
1.The dominant Wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. )
2. Forward Voltage: +/-0.1V.
*Wavelength value is in accordance with CIE127-2007 standards.
Dec 16, 2013
SDSA9026 V2-Z
Layout: Maggie L.
P. 3/7
Part Number: ZMD20X92S-4
3.5x3.5 mm SMD CHIP LED LAMP
www.SunLED.com
u
S
Dec 16, 2013
L
n
D
E
SDSA9026 V2-Z
Layout: Maggie L.
P. 4/7
Part Number: ZMD20X92S-4
3.5x3.5 mm SMD CHIP LED LAMP
www.SunLED.com
u
S
Dec 16, 2013
L
n
D
E
SDSA9026 V2-Z
Layout: Maggie L.
P. 5/7
Part Number: ZMD20X92S-4
3.5x3.5 mm SMD CHIP LED LAMP
www.SunLED.com
LED is recommended for reflow soldering and
soldering profile is shown below.
The device has a single mounting surface.
The device must be mounted according to
the specifications.
D
E
L
n
u
S
Reel Dimension
Recommended Soldering Pattern
Tape Specification (Units : mm)
Dec 16, 2013
SDSA9026 V2-Z
Layout: Maggie L.
P. 6/7
Part Number: ZMD20X92S-4
3.5x3.5 mm SMD CHIP LED LAMP
www.SunLED.com
PACKING & LABEL SPECIFICATIONS
D
E
L
n
u
S
TERMS OF USE
1. Data presented in this document reflect statistical figures and should be treated as technical reference only.
2. Contents within this document are subject to improvement and enhancement changes without notice.
3. The product(s) in this document are designed to be operated within the electrical and environmental specifications indicated on the datasheet.
User accepts full risk and responsibility when operating the product(s) beyond their intended specifications.
4. The product(s) described in this document are intended for electronic applications in which a person’s life is not reliant upon the LED. Please
consult with a SunLED representative for special applications where the LED may have a direct impact on a person’s life.
5. The contents within this document may not be altered without prior consent by SunLED.
6. Additional technical notes are available at http://www.SunLED.com/TechnicalNotes
Dec 16, 2013
SDSA9026 V2-Z
Layout: Maggie L.
P. 7/7