PYF@@S/P2RF-@@-S - OMRON Industrial Automation

Screwless Clamp Terminal Sockets
PYF@@S/P2RF-@@-S
CSM_PYF__S/P2RF-__-S_DS_E_2_1
New Screwless Terminal Sockets Added
for MY and G2R Relays.
• Simplified wiring without tightening screws.
• Two wires can be independently wired for each terminal.
• Coil terminals and contact terminals are completely separated
in an organized wiring layout.
• Release Levers and Nameplates are available (sold
separately).
Features
Structured for Easy Wiring
Complete Wiring in Three Steps
Contact terminal
(common)
Contact terminal
(NO)
Contact terminal
(NC)
Release Lever
(sold separately)
Insert
a screwdriver.
Screwdriver
inserted.
Insert the wire.
Remove screwdriver
to complete wiring.
• A spring holds the wire in place to reduce wiring work by 30%
(according to OMRON comparison) and eliminates the need to
manage torque.
• DIN terminal numbers also indicated.
Coil terminals
Nameplate
(sold separately)
Ordering Information
Sockets
Applicable model (typical example)
MY2
Socket
Model
PYF08S
MY4
PYF14S
G2R-1-S
P2RF-05-S
G2R-2-S
P2RF-08-S
Options (Order Separately)
Applicable Socket
Release Bar
Nameplates
Model
Model
PYF08S
PYCM-08S
PYF14S
PYCM-14S
P2RF-05-S
P2RF-08-S
P2CM-S
R99-11
Socket Bridges with Red Insulation Socket Bridges with Blue Insulation
Model
Model
PYDM-08SR
PYDM-08SB
PYDM-14SR
PYDM-14SB
P2RM-SR
P2RM-SB
Note: Pieces per Package
Nameplates: 100
Socket Bridges: 50
1
PYF@@S/P2RF-@@-S
Ratings/Characteristics
Characteristics
PYF@@S
Item
Model
PYF08S
PYF14S
Ambient operating temperature −55 to 70°C
Ambient operating humidity
5% to 85%
Continuous carry current*
Dielectric
strength
10 A
5A
Between contact
terminals of same
polarity
2,000 VAC, 1 min
2,000 VAC, 1 min
Between contact
terminals of
different polarity
2,000 VAC, 1 min
2,000 VAC, 1 min
Between coil and
contact terminals
2,000 VAC, 1 min
2,000 VAC, 1 min
Insulation resistance
1,1,000 MΩ min.
Weight (approx.)
46 g
62 g
* The continuous carry current of 10 A for the PYF08S is for an ambient temperature of 55°C.
At an ambient temperature of 70°C, the value is 7 A.
P2RF-@@-S
Item
Model
P2RF-05-S
P2RF-08-S
Ambient operating temperature −55 to 70°C
Ambient operating humidity
5% to 85%
Continuous carry current
Dielectric
strength
10 A
5A
Between contact
terminals of same
polarity
1,000 VAC, 1 min
1,000 VAC, 1 min
Between contact
terminals of
different polarity
---
3,000 VAC, 1 min
Between coil and
contact terminals
4,000 VAC, 1 min
4,000 VAC, 1 min
Insulation resistance
1,000 MΩ min.
Weight (approx.)
36 g
40 g
Ratings for Safety Standard Certification
PYF@@S
Standard
VDE0627 (EN61984)
File No.
Nr.B387 (License No.)
UL508 (UL1059)
E87929 Vol.3
CSA C22.2 No.14 (CSA C22.2 No.158)
LR31928
P2RF-@@-S
Standard
VDE0627 (EN61984)
File No.
Nr.6166 (License No.)
UL508 (UL1059)
E87929 Vol.3
CSA C22.2 No.14 (CSA C22.2 No.158)
LR31928
2
PYF@@S/P2RF-@@-S
Dimensions
(Unit: mm)
Sockets
PYF08S
38.2 max.
36.5 max.
Terminal Arrangement/
Internal Connection Diagram
(Top View)
32.6
27.6
22.6
23.2 max.
(3.4)
12
9
(41)
(11)
8
5
(44)
(14)
4
1
85 max.
(12)
(42)
24.5
35.4
(A1)
(A2)
14
(5)
28.6
(5.3)
13
Note: Figures in parentheses indicate
DIN standard numbers.
32.6
PYF14S
36.5 max.
Terminal Arrangement/
Internal Connection Diagram
(Top View)
12 11 10 9
(41) (31) (21) (11)
32.6
27.6
31 max.
22.6
8
7
24.55
(42) (32) (22) (12)
3
2
1
35.4
(A2)
14
(4.15)
5
(44) (34) (24) (14)
4
85 max.
6
(3.4)
28.6
32.6
(A1)
13
Note: Figures in parentheses indicate
DIN standard numbers.
3
PYF@@S/P2RF-@@-S
P2RF-05-S
Terminal Arrangement/
Internal Connection Diagram
(Top View)
4
(11)
32.6
3
27.6
18.0 max.
(14)
22.6
2
24.5
(12)
35.3
91.8 max.
(A1) (A2)
5
(2.4)
28.5
1
(5.3)
Note: Figures in parentheses indicate
DIN standard numbers.
32.6
P2RF-08-S
Terminal Arrangement/
Internal Connection Diagram
(Top View)
6
27.6
22.6
18.0 max.
3
(21) (11)
32.6
5
(3.4)
7
24.5
4
(24) (14)
2
(22) (12)
35.3
91.8 max.
(A1) (A2)
8
(2.4)
28.6
32.6
1
(5.3)
Note: Figures in parentheses indicate
DIN standard numbers.
4
PYF@@S/P2RF-@@-S
Accessories (Order Separately)
Socket Bridges
Insulating coating
14
9
Length
Guide: 1.2 dia.
Applicable
Sockets
Model
Length (mm)
PYDM-08SR
PYF08S
PYDM-14SR
Blue
Red
27.5
PYDM-14SB
P2RM-SR
P2RF-@@-S
Red
19.7
PYDM-08SB
PYF14S
Insulation
color
Blue
Red
14.3
P2RM-SB
Blue
Note: Use the Socket Bridges for relay coil bridge wiring.
Release Levers
PYCM-14S
PYCM-08S
16
28
54.4
52.5
32.7
29.6
P2CM-S
16.8
40.35
36
Mounting Heights
PYF08S
PYF14S
P2RF-@@-S
G2R(S)
MY
MY
73.6
72.6
64
64
28.6
24
28.6
(3.4)
63.5
68.5
(3.4)
(5.3)
5
PYF@@S/P2RF-@@-S
Safety Precautions
Precautions for Safe Use
• Do not move the screwdriver up, down, or from side to side or
rotate it while it is inserted in the hole. Doing so may damage
internal components in the Socket.
Precautions for Correct Use
Wiring Tools
Applicable Screwdriver
Use a flat-blade screwdriver with a tip that is 2.5 mm wide (3.0 mm
max.).
2.5 mm (3.0 mm max. )
• Do not insert more than one wire into the same hole. Doing so may
cause abnormal heating.
• There are two internally connected wiring holes for each terminal.
• Insert the screwdriver along the hole wall as shown below.
You cannot use a screwdriver with a thick shaft.
Applicable Screwdriver (Example)
VESSEL No.9900 − (−) 2.5 × 75
Applicable Wires
• You can use either solid wires or stranded wires. Applicable wire
size: 0.2 to 1.5 mm2 (AWG24 to AWG16)
• Strip 8 to 9 mm of insulation from the ends of the wires.
Screwdriver
• When you remove a Socket from a support rail, insert the end of a
screwdriver into the fixture and move the screwdriver as shown by
the arrow in the following figure.
Screwdriver
8 to 9 mm
• If you insert stranded wires without ferrules, make sure that the
wires are twisted when you insert them.
• If you use bare ferrules, always attach insulating sleeves.
• If you insert a wire with a sheath outer diameter of 2.2 mm or less,
do not insert the wire far enough so that the sheath is engaged
inside the hole, as shown below.
Fixture rail
• When you use a Release Lever to remove a Relay from a P2RF@@-S Socket, insert a screwdriver at the location shown in the
following figure and move the Release Lever in the direction
indicated by the arrow to release the lock on the release lever.
• Two wires with a sheath outer diameter of 3.2 mm or larger cannot
be inserted for the same terminal at the same time.
• Use heat-shrinking tubes to indicate wire numbers.
6
PYF@@S/P2RF-@@-S
Wiring
A
12
11
10
9
41
31
21
11
Wire insertion holes
Screwdriver insertion holes
A
(1) Insert a screwdriver into a screwdriver insertion hole on the
Socket.
Cross-section A-A
Spring
Wire insertion hole
Screwdriver
Screwdriver insertion hole
(2) Press the screwdriver in until it reaches the stopper inside the
Socket. The spring at the back of the wire insertion hole will be
completely open in this condition. The screwdriver will be held in
place even if you remove your hand.
(3) With the screwdriver held in place, insert the wire or ferrule into
the wire insertion hole.
Wire
(4) Remove the screwdriver. The spring will hold the wire. This
concludes the connection procedure.
7
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2015.7
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2015 All Right Reserved.