Long-distance Proximity Sensor TL-LP/LY CSM_TL-LP/LY_DS_E_4_1 Long-distance Model with a Sensing distance of 50 mm. Be sure to read Safety Precautions on page 3. Ordering Information Appearance Sensing distance Column type (flat-surface mounting) Output configuration Model 3-wire DC (normally open) TL-LP50 1M 50 mm 2-wire AC (normally open) TL-LY50 1M Note: Models with different frequencies are available. The model numbers are TL-L@50B. Ratings and Specifications Item Sensing distance Set distance Differential travel Model Sensing object Standard sensing object Response time Power supply voltage (operating voltage range *) Current consumption Leakage current TL-LP50 TL-LY50 50 mm±10% 0 to 40 mm 10% max. of sensing distance Ferrous metals (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on the next page.) Iron, 100 × 100 × 1 mm 15 ms max. 25 ms max. 12 to 24 VDC (10 to 30 VDC), ripple (p-p) 10% max. 100 to 220 VAC (90 to 250 VAC), 50/60 Hz 10 mA max. (with no load) ----Refer to Engineering Data on the next page. NPN open collector with a maximum current of Switching capacity 10 to 200 mA 200 mA at 30 VDC Control output 3 V max. under a load current of 200 mA and a cable Residual voltage Refer to Engineering Data on the next page. length of 2 m Indicators Operation indicator (red) Operation mode (with sensNO. Refer to the timing charts under I/O Circuit Diagrams on page 3 for details. ing object approaching) Ambient temperature Operating/Storage: −25 to 70°C (with no icing or condensation) Ambient humidity Operating/Storage: 35% to 95% (with no condensation) Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C Voltage influence ±2% max. of sensing distance within a range of ±10% of rated power supply voltage Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case 500 VAC (50/60 Hz) for 1min between current2,000 VAC (50/60 Hz) for 1 min between currentDielectric strength carrying parts and case carrying parts and case Vibration resistance 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions (destruction) Shock resistance 1,000m/s2 10 times each in X, Y, and Z directions (destruction) Degree of protection IEC IP67 Connection method Pre-wired Models (Standard cable length: 1 m) Weight (packed state) Approx. 1.4 kg Die-cast aluminum Materi- Case als Sensing surface Polyester Accessories Instruction sheet * Full-wave rectified power supplies with a mean output of 24 VDC ±10% are available for the TL-LP50. 1 TL-LP/LY Engineering Data (Reference Value) Leakage Current TL-LY50 80 Leakage current (mA) Distance X (mm) Sensing Area TL-LP/-LY Y 70 X 60 50 3.0 mA 100/200 VAC VL 2.5 2.0 200 VAC 1.5 40 30 1.0 100 VAC 20 0.5 10 0 0.3 0.5 −60 −40 −20 0 20 1 5 10 50 100 Load resistance (kΩ) 40 Distance Y (mm) 85-dia. head at 100 VAC 150 100 TL-LY50 Load voltageVL (V) Load voltageVL (V) Residual Voltage TL-LY50 Operate at 200 VAC 250 200 Operate ON ON 150 V V mA 50 VL 100 VAC mA 100 VL 200 VAC 50 Reset Reset OFF 5 10 50 Distance X (mm) Sensing Object Size and Material vs. Sensing Distance TL-LP/-LY 70 60 @l X t = 1 mm Iron 50 OFF 100 500 Load current (mA) Stainless steel (SUS304) 2 5 10 500 100 Load current (mA) 50 Column-type Sensing Object Diameter and Material vs. Sensing Distance TL-LP/-LY 60 50 Reset Iron Operate 40 l > 120 D dia. 40 30 30 X Sensing Object Thickness and Material vs. Sensing Distance TL-LP/-LY Distance X (mm) 3 Distance X (mm) 2 70 Aluminum 60 Reset Iron 50 Operate 40 Brass 30 20 20 Reset Brass 10 0 Aluminum 50 100 150 Size of sensing object: I (mm) 20 10 0 10 @100 t Operate 10 30 50 70 90 120 140 External diameter D dia. (mm) 0 X 0.01 Reset Operate 0.02 0.05 0.1 1 2 Thickness of sensing object t (mm) 2 TL-LP/LY I/O Circuit Diagrams 3-wire DC Model Output configuration Model Timing charts Sensing object NO TL-LP50 Output circuit Brown Present Not present Output transistor (Load) ON OFF Operation indicator (red) ON OFF +V Load 1.8 Ω Proximity Sensor main circuit Black 200 mA max. 2.2 Ω Blue 0V 2-wire AC Model Output configuration Model Timing charts Output circuit Brown Sensing object NO TL-LY50 Load Present Not present Reset Operation indicator (red) AC power supply Proximity Sensor main circuit Operate Load Blue ON OFF Safety Precautions WARNING Mutual Interference When two or more Sensors are mounted face-to-face or sideby-side, separate them as shown below. This product is not designed or rated for ensuring safety of persons. Do not use it for such purposes. Face-to-face Mounting Precautions for Correct Use Parallel Mounting A Do not use this product under ambient conditions that exceed the ratings. ● Design Effects of Surrounding Metal Be sure to separate the Sensor from surrounding metal objects as shown in the following illustration. B (Unit: mm) Distance Model TL-L@50 A 1,000 (500) B 700 (176) Note: Figures in parentheses will apply if the Sensors in use are different from each other in response frequency. 150 mm 70 mm 70 mm (Unit: mm) Dimensions TL-LP50 TL-LY50 Unless otherwise specified, the tolerance class IT16 is used for dimensions in this data sheet. Operation indicator (red) 76 44 106 20 Mounting Holes Four, 7-dia. holes 88 Four, 6.5-dia. holes *2 16 85 dia. 30 88 88 106 *1 88 18.5 R5 75 5 *1. Vinyl cabtire cable: TL-LP50: 9.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.75 mm2, Insulator diameter: 2.8 mm), Standard length: 1 m TL-LY50: 9.0-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.75 mm2, Insulator diameter: 2.8 mm), Standard length: 1 m *2. Remove the hexagon nut if a PF1/2 cable protective tube is applied. In the interest of product improvement, specifications are subject to change without notice. 3 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2015.7 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2015 All Right Reserved.