THC63LVDM83C(5S) _Rev.1.10_E THC63LVDM83C(5S) REDUCED SWING LVDS 24Bit COLOR HOST-LCD PANEL INTERFACE General Description Features The THC63LVDM83C(5S) transmitter is designed to support pixel data transmission between Host and Flat Panel Display from NTSC up to SXGA+ resolutions. The THC63LVDM83C(5S) converts 28bits of CMOS/ TTL data into LVDS(Low Voltage Differential Signaling) data stream. The transmitter can be programmed for rising edge or falling edge clocks through a dedicated pin. At a transmit clock frequency of 85MHz, 24bits of RGB data and 4bits of timing and control data (HSYNC, VSYNC, CNTL1, CNTL2) are transmitted at an effective rate of 595Mbps per LVDS channel. • Wide dot clock range: 8-85MHz suited for NTSC, VGA, SVGA, XGA • • • • • • • • • • PLL requires no external components Supports spread spectrum clock generator On chip jitter filtering Clock edge selectable Supports reduced swing LVDS for low EMI Power down mode Low power single 3.3V CMOS design Low profile 56 Lead TSSOP Package 1.2 up to 3.3V tolerant data inputs to connect directly to low power,low voltage application and graphic processor. Backward compatible with THC63LVDM83R(24bits) Block Diagram THC63LVDM83C(5S) CMOS/TTL INPUTS TB0-6 TC0-6 TD0-6 7 7 7 7 TTL PARALLEL TO SERIAL TA0-6 DATA (LVDS) TA +/TB +/TC +/TD +/(56-595Mbit/On Each LVDS Channel) TRANSMITTER CLKIN (8 to 85MHz) TCLK +/CLOCK (LVDS) 8-85MHz PLL R/F /PDWN RS Copyright (C)2015 THine Electronics, Inc. 1/12 THine Electronics, Inc. Security E THC63LVDM83C(5S)_Rev.1.10_E Pin Out THC63LVDM83C(5S) RS TD1 TA5 TA6 GND TB0 TB1 TD2 VCC TD3 TB2 TB3 GND TB4 TB5 TD4 R/F TD5 TB6 TC0 GND TC1 TC2 TC3 TD6 VCC TC4 TC5 Copyright (C)2015 THine Electronics, Inc. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 2/12 TA4 TA3 TA2 GND TA1 TA0 TD0 LVDS GND TATA+ TBTB+ LVDS VCC LVDS GND TCTC+ TCLKTCLK+ TDTD+ LVDS GND PLL GND PLL VCC PLL GND /PDWN CLK IN TC6 GND THine Electronics, Inc. Security E THC63LVDM83C(5S)_Rev.1.10_E Pin Description Pin Name Pin # Type Description TA+, TA- 47, 48 LVDS OUT TB+, TB- 45, 46 LVDS OUT TC+, TC- 41, 42 LVDS OUT TD+, TD- 37, 38 LVDS OUT TCLK+, TCLK- 39, 40 LVDS OUT TA0 ~ TA6 51, 52, 54, 55, 56, 3, 4 IN TB0 ~ TB6 6, 7, 11, 12, 14, 15, 19 IN TC0 ~ TC6 20, 22, 23, 24, 27, 28, 30 IN TD0 ~ TD6 50, 2, 8, 10, 16, 18, 25 IN /PDWN 32 IN LVDS Data Out. LVDS Clock Out. Pixel Data Inputs. H: Normal operation, L: Power down (all outputs are Hi-Z) LVDS swing mode, VREF select. RS 1 RS LVDS Swing Small Swing Input Support VCC 350mV N/A 0.6 ~ 1.4V 350mV RS=VREFa GND 200mV N/A IN a. VREF is Input Reference Voltage. Input Clock Triggering Edge Select. R/F 17 IN VCC 9, 26 Power CLKIN 31 IN GND 5, 13, 21, 29, 53 H: Rising edge, L: Falling edge Power Supply Pins for TTL inputs and digital circuitry. Clock in. Ground Ground Pins for TTL inputs and digital circuitry. LVDS VCC 44 Power Power Supply Pins for LVDS Outputs. LVDS GND 36, 43, 49 Ground Ground Pins for LVDS Outputs. PLL VCC 34 Power Power Supply Pin for PLL circuitry. PLL GND 33, 35 Ground Ground Pins for PLL circuitry. Copyright (C)2015 THine Electronics, Inc. 3/12 THine Electronics, Inc. Security E THC63LVDM83C(5S) _Rev.1.10_E Absolute Maximum Ratings 1 Supply Voltage (VCC) -0.3V ~ +4.0V CMOS/TTL Input Voltage -0.3V ~ (VCC + 0.3V) CMOS/TTL Output Voltage -0.3V ~ (VCC + 0.3V) LVDS Driver Output Voltage -0.3V ~ (VCC + 0.3V) Output Current continuous Junction Temperature +125 °C Storage Temperature Range -55 °C ~ +150 °C Resistance to soldering heat +260 °C /10sec Maximum Power Dissipation @+25 °C 0.5W Recommended Operating Conditions Parameter Min Typ Max Units All Supply Voltage 3.0 3.3 3.6 V Operating Ambient Temperature -40 85 °C CLK IN Frequency 8 85 MHz 1. “Absolute Maximum Ratings” are those valued beyond which the safety of the device can not be guaranteed. They are not meant to imply that the device should be operated at these limits. The tables of “Electrical Characteristics” specify conditions for device operation. Copyright (C)2015 THine Electronics, Inc. 4/12 THine Electronics, Inc. Security E THC63LVDM83C(5S)_Rev.1.10_E Electrical Characteristics CMOS/TTL DC Specifications VCC = VCC = PLL VCC = LVDS VCC Symbol Parameter VIH High Level Input Voltage RS=VCC or GND 2.0 VCC V VIL Low Level Input Voltage RS=VCC or GND GND 0.8 V 1.2 2.8 V VDDQ1 Conditions Small Swing Voltage VREF Input Reference Voltage Small Swing (RS=VDDQ/2) VSH2 Small Swing High Level Input Voltage VREF = VDDQ/2 VSL2 Small Swing Low Level Input Voltage VREF = VDDQ/2 IINC Input Current 0V ≤ V IN ≤ V CC Min. Typ. Max. Units VDDQ/2 VDDQ/2 +100mV V VDDQ/2 -100mV ± 10 V uA Notes: 1VDDQ voltage defines max voltage of small swing input. It is not an actual input voltage. 2 Small swing signal is applied to TA0-6,TB0-6,TC0-6,TD0-6 and CLKIN. LVDS Transmitter DC Specifications VCC = VCC = PLL VCC = LVDS VCC Symbol Parameter Conditions Normal swing VOD Differential Output Voltage RL=100Ω Min. Typ. Max. Units 250 350 500 mV 100 200 300 mV 35 mV RS=VCC Reduced swing RS=GND ΔVOD VOC Change in VOD between complementary output states Common Mode Voltage ΔVOC Change in VOC between complementary output states IOS Output Short Circuit Current IOZ Output TRI-STATE Current Copyright (C)2015 THine Electronics, Inc. RL=100Ω VOUT=0V, RL=100Ω /PDWN=0V, VOUT=0V to VCC 5/12 1.125 1.25 1.375 V 35 mV -24 mA ± 10 uA THine Electronics, Inc. Security E THC63LVDM83C(5S)_Rev.1.10_E Supply Current VCC = VCC = PLL VCC = LVDS VCC Symbol ITCCG Parameter Transmitter Supply Current Condition(*) RL=100Ω,CL=5pF VCC=3.3V, f=85MHz Gray Scale Pattern ITCCW Transmitter Supply Current RL=100Ω,CL=5pF VCC=3.3V, f=85MHz Worst Case Pattern ITCCS Transmitter Power Down Supply Current /PDWN = L Typ. Max. Units RS=VCC 52 58 mA RS=GND 40 46 mA RS=VCC 61 67 mA RS=GND 50 56 mA 10 uA Gray Scale Pattern CLK Tx1 Tx2 Tx3 Tx4 Tx5 Tx6 x= A, B, C, D Worst Case Pattern CLK Tx1 Tx2 Tx3 Tx4 Tx5 Tx6 x= A, B, C, D Fig1. Data Pattern Copyright (C)2015 THine Electronics, Inc. 6/12 THine Electronics, Inc. Security E THC63LVDM83C(5S)_Rev.1.10_E Switching Characteristics VCC = VCC = PLL VCC = LVDS VCC Symbol Parameter tTCIT CLK IN Transition time tTCP CLK IN Period tTCH Min. Typ. Max. Units 5.0 ns 11.7 T 125 ns CLK IN High Time 0.35T 0.5T 0.65T ns tTCL CLK IN Low Time 0.35T 0.5T 0.65T ns tTCD CLK IN to TCLK+/- Delay tTS TTL Data Setup to CLK IN tTH TTL Data Hold from CLK IN tLVT LVDS Transition Time 3T ns 2.5 ns 0 ns 0.6 1.5 ns 0.0 +0.2 ns tTOP1 Output Data Position0 (T=11.7ns) -0.2 tTOP0 Output Data Position1 (T=11.7ns) T --- – 0.2 7 T --7 T --- + 0.2 7 ns tTOP6 Output Data Position2 (T=11.7ns) T 2 --- – 0.2 7 T 2 --7 T 2 --- + 0.2 7 ns tTOP5 Output Data Position3(T=11.7ns) T 3 --- – 0.2 7 T 3 --7 T 3 --- + 0.2 7 ns tTOP4 Output Data Position4 (T=11.7ns) T 4 --- – 0.2 7 T 4 --7 T 4 --- + 0.2 7 ns tTOP3 Output Data Position5 (T=11.7ns) T 5 --- – 0.2 7 T 5 --7 T 5 --- + 0.2 7 ns tTOP2 Output Data Position6 (T=11.7ns) T 6 --- – 0.2 7 T 6 --7 T 6 --- + 0.2 7 ns tTPLL Phase Lock Loop Set 10.0 ms AC Timing Diagrams TTL Input 90% CLK IN 90% 10% 10% t TCIT t TCIT Fig2. CLKIN Transition Time LVDS Output Vdiff=(TA+)-(TA-) TA+ Vd if f 5pF 80% 80% 20% 20% 100Ω TAt LVT LVDS Output Load t LVT Fig3. LVDS Output Load and Transition Time Copyright (C)2015 THine Electronics, Inc. 7/12 THine Electronics, Inc. Security E THC63LVDM83C(5S)_Rev.1.10_E RS Pin VCC 0.6~1.4V GND tTCP TTL Inputs tTC H VOD 350mV 200mV VCC CLK IN VCC/2 VCC/2 VCC/2 GND t T CL tT S tT H VCC Tx0-Tx6 VCC/2 VCC/2 GND t TCD TCLK+ VOD VOC TCLKNote: CLK IN: for R/F=GND, denote as solid line, for R/F=VCC, denote as dashed line. Fig4. CLKIN Period, High/Low Time, Setup/Hold Timing Small Swing Inputs tTC P t T CH RS Pin VREF VCC 0.6~1.4V GND VCC/2 Input Voltage of RS pin VCC/2 VD DQ CLK IN VD DQ /2 V DD Q /2 VREF VDD Q /2 GND t TCL t TS t TH VDDQ Tx0-Tx6 V D D Q/ 2 VD DQ /2 VREF GND tTCD TCLK+ VOC TCLK- Note: CLK IN: for R/F=GND, denote as solid line, for R/F=VCC, denote as dashed line. Fig5. Small Swing Inputs Copyright (C)2015 THine Electronics, Inc. 8/12 THine Electronics, Inc. Security E THC63LVDM83C(5S)_Rev.1.10_E AC Timing Diagrams LVDS Output TCLK+/(Differential) Vdiff = 0V Vdiff = 0V TA+/- TA6 TA5 TA4 TA3 TA2 TA1 TA0 TB+/- TB6 TB5 TB4 TB3 TB2 TB1 TB0 TC+/- TC6 TC5 TC4 TC3 TC2 TC1 TC0 TD+/- TD6 TD5 TD4 TD3 TD2 TD1 TD0 Previous Cycle Next Cycle t TOP1 t TOP0 t TOP6 t TOP5 t TOP4 t TOP3 t TOP2 Fig6. LVDS Output Data Position Phase Lock Loop Set Time /PDWN 2.0V 3.6V VCC 3.0V tTPLL CLKIN Vdiff = 0V TCLK+/Fig7. PLL Lock Set Time Copyright (C)2015 THine Electronics, Inc. 9/12 THine Electronics, Inc. Security E THC63LVDM83C(5S) _Rev.1.10_E Note 1)Cable Connection and Disconnection Don't connect and disconnect the LVDS cable, when the power is supplied to the system. 2)GND Connection Connect the each GND of the PCB which THC63LVDM83C(5S) and LVDS-Rx on it. It is better for EMI reduction to place GND cable as close to LVDS cable as possible. 3)Multi Drop Connection Multi drop connection is not recommended. TCLK+ THC63LVDM83C(5S) LVDS-Rx TCLK- LVDS-Rx 4)Asynchronous use Asynchronous use such as following systems are not recommended. CLKOUT DATA TCLK+ THC63LVDM83C(5S) CLKOUT LVDS-Rx TCLK- TCLK- IC IC CLKOUT DATA TCLK+ THC63LVDM83C(5S) CLKOUT DATA LVDS-Rx TCLK- DATA TCLK+ THC63LVDM83C(5S) TCLK- IC IC TCLK+ CLKOUT DATA Copyright (C)2015 THine Electronics, Inc. THC63LVDM83C(5S) TCLK- 10/12 THine Electronics, Inc. Security E THC63LVDM83C(5S) _Rev.1.10_E Package 56 Lead Molded Thin Shrink Small Outline Package, JEDEC Unit : millimeters 14.0 ± 0.1 56 29 8.1 ± 0.1 6.1 ± 0.1 4.05 1 28 (1.0) 1.2 MAX 0.10 ± 0.05 0.50 TYP Copyright (C)2015 THine Electronics, Inc. 0.20 TYP 11/12 THine Electronics, Inc. Security E THC63LVDM83C(5S)_Rev.1.10_E Notices and Requests 1. The product specifications described in this material are subject to change without prior notice. 2. The circuit diagrams described in this material are examples of the application which may not always apply to the customer's design. We are not responsible for possible errors and omissions in this material. Please note if errors or omissions should be found in this material, we may not be able to correct them immediately. 3. This material contains our copy right, know-how or other proprietary. Copying or disclosing to third parties the contents of this material without our prior permission is prohibited. 4. Note that if infringement of any third party's industrial ownership should occur by using this product, we will be exempted from the responsibility unless it directly relates to the production process or functions of the product. 5. Product Application 5.1 Application of this product is intended for and limited to the following applications: audiovide deice, officce automation device, communication device, consumer electronics, smartphone, feature phone, and amusement machinedevice. This product must not be used for applications that require extremely high-reliability/safety such as aerospace device, traffic device, transportation device, nuclear power control device, combustion chamber device, medical device related to critical care, or any kind of safety device. 5.2 This product is not intended to be used as an automotive part, unless the product is specified as a product conforming to the demandes and specifications of ISO/TS16949 (“the specified Product”) in this data sheet. THine Electronics, Inc.(“THine”) accepts no liability what so every for any product other than the Specified Product for it not conforming to the aforementioned demands and specifications. 5.3 THine accepts liability for demands and specifications of the Specified Product only to the extent that the user and THine have been previously and explicitly agreed to each other. 6. Despite our utmost efforts to improve the quality and reliability of the product, faults will occur with a certain small probability, which is inevitable to a semi-conductor product. Therefore, you are encouraged to have sufficiently redundant or error preventive design applied to the use of the product so as not to have our product cause any social or public damage. 7. Please note that this product is not designed to be radiation-proof. 8. Customers are asked, if required, to judge by themselves if this product falls under the category of strategic goods under the Foreign Exchange and Foreign Trade Control Law. THine Electronics, Inc. E-mail: [email protected] Copyright (C)2015 THine Electronics, Inc. 12/12 THine Electronics, Inc. Security E