FERROXCUBE DATA SHEET E22/6/16/R Planar E cores and accessories Supersedes data of September 2004 2008 Sep 01 Ferroxcube Planar E cores and accessories E22/6/16/R CORES Effective core parameters of an E/PLT combination SYMBOL PARAMETER VALUE UNIT Σ(I/A) core factor (C1) 0.324 mm −1 Ve effective volume 2100 mm 3 Ie effective length 26.1 mm Ae effective area 78.5 mm 2 Amin minimum area 72.6 mm 2 m mass of E core half ≈ 6.5 g m mass of plate ≈4 g 21.8 ±0.4 16.8 ±0.4 5 ±0.1 andbook, halfpage 3.2 ±0.1 Ordering information for plates GRADE 2.8 TYPE NUMBER 3C90 PLT22/16/2.5/S-3C90 3C92 PLT22/16/2.5/S-3C92 3C93 PLT22/16/2.5/S-3C93 3C94 PLT22/16/2.5/S-3C94 3C95 PLT22/16/2.5/S-3C95 3C96 PLT22/16/2.5/S-3C96 3F3 PLT22/16/2.5/S-3F3 3F35 PLT22/16/2.5/S-3F35 3F4 PLT22/16/2.5/S-3F4 3F45 PLT22/16/2.5/S-3F45 3E6 PLT22/16/2.5/S-3E6 4.7 ±0.15 5.7 ±0.1 +0.2 0 15.8 ±0.3 CBW177 Dimensions in mm. Fig.1 E22/6/16/R. 21.8 ±0.4 2.5 ±0.1 ndbook, halfpage 2.9 ±0.05 15.8 ±0.3 2.9 +0.2 0 CBW178 Dimensions in mm. Fig.2 PLT22/16/2.5/S. 2008 Sep 01 2 Ferroxcube Planar E cores and accessories E22/6/16/R Core halves for use in combination with a slotted plate (PLT/S) AL measured in combination with a slotted plate (PLT/S) clamping force for AL measurements, 20 ±10 N; measurement coil as for E22/6/16. GRADE 3C90 AL (nH) µe 160 ±3% ≈ 42 AIR GAP (µm) ≈ 950 TYPE NUMBER E22/6/16/R-3C90-A160-P 250 ±3% ≈ 66 ≈ 550 E22/6/16/R-3C90-A250-P 315 ±3% ≈ 83 ≈ 400 E22/6/16/R-3C90-A315-P 400 ±5% ≈ 106 ≈ 280 E22/6/16/R-3C90-A400-P 630 ±8% ≈ 166 ≈ 160 E22/6/16/R-3C90-A630-P 6150 ±25% ≈ 1620 ≈0 E22/6/16/R-3C90 3C92 4410 ±25% ≈ 1140 ≈0 E22/6/16/R-3C92 3C93 5000 ±25% ≈ 1290 ≈0 E22/6/16/R-3C93 3C94 160 ±3% ≈ 42 ≈ 950 E22/6/16/R-3C94-A160-P 250 ±3% ≈ 66 ≈ 550 E22/6/16/R-3C94-A250-P 315 ±3% ≈ 83 ≈ 400 E22/6/16/R-3C94-A315-P 400 ±5% ≈ 106 ≈ 280 E22/6/16/R-3C94-A400-P 630 ±8% ≈ 166 ≈ 160 E22/6/16/R-3C94-A630-P 6150 ±25% ≈ 1620 ≈0 E22/6/16/R-3C94 3C95 7360 ±25% ≈ 1950 ≈0 E22/6/16/R-3C95 3C96 5450 ±25% ≈ 1440 ≈0 ≈ 42 ≈ 950 3F3 160 ±3% E22/6/16/R-3C96 E22/6/16/R-3F3-A160-P 250 ±3% ≈ 66 ≈ 550 E22/6/16/R-3F3-A250-P 315 ±3% ≈ 83 ≈ 400 E22/6/16/R-3F3-A315-P 400 ±5% ≈ 106 ≈ 280 E22/6/16/R-3F3-A400-P 630 ±8% ≈ 166 ≈ 160 E22/6/16/R-3F3-A630-P 5000 ±25% ≈ 1320 ≈0 3F35 4100 ±25% ≈ 1080 ≈0 3F4 160 ±3% ≈ 42 ≈ 950 E22/6/16/R-3F35 E22/6/16/R-3F4-A160-P 250 ±3% ≈ 66 ≈ 550 E22/6/16/R-3F4-A250-P 315 ±3% ≈ 83 ≈ 400 E22/6/16/R-3F4-A315-P 400 ±5% ≈ 106 ≈ 280 E22/6/16/R-3F4-A400-P 630 ±8% ≈ 166 ≈ 160 E22/6/16/R-3F4-A630-P 2900 ±25% ≈ 770 ≈0 E22/6/16/R-3F4 ≈ 770 ≈0 E22/6/16/R-3F45 ≈ 6900 ≈0 E22/6/16/R-3E6 3F45 2900 ±25% 3E6 26000 +40/−30% 2008 Sep 01 E22/6/16/R-3F3 3 Ferroxcube Planar E cores and accessories E22/6/16/R Properties of core sets under power conditions B (mT) at CORE LOSS (W) at GRADE H = 250 A/m; f = 10 kHz; T = 100 °C f = 100 kHz; ˆ = 100 mT; B T = 100 °C f = 100 kHz; ˆ = 200 mT; B T = 25 °C f = 100 kHz; ˆ = 200 mT; B T = 100 °C f = 400 kHz; ˆ = 50 mT; B T = 100 °C f = 500 kHz; ˆ = 50 mT; B T = 100 °C E22/R+PLT22/S-3C90 ≥320 ≤ 0.23 − − − − E22/R+PLT22/S-3C92 ≥370 ≤ 0.18 − ≤ 1.25 − − E22/R+PLT22/S-3C93 ≥320 ≤ 0.18(1) − ≤ 1.25(1) − − E22/R+PLT22/S-3C94 ≥320 ≤ 0.18 − ≤ 1.25 − − E22/R+PLT22/S-3C95 ≥320 − ≤ 1.24 ≤ 1.18 − − E22/R+PLT22/S-3C96 ≥320 ≤ 0.14 − ≤ 1.0 ≤ 0.38 ≤ 0.75 E22/R+PLT22/S-3F3 ≥300 ≤ 0.23 − − ≤ 0.4 − E22/R+PLT22/S-3F35 ≥300 − − − ≤ 0.2 ≤ 0.3 E22/R+PLT22/S-3F4 ≥250 − − − − − E22/R+PLT22/S-3F45 ≥250 − − − − − 1. Measured at 140 °C. Properties of core sets under power conditions (continued) B (mT) at CORE LOSS (W) at GRADE H = 250 A/m; f = 10 kHz; T = 100 °C f = 500 kHz; ˆ = 100 mT; B T = 100 °C f = 1 MHz; ˆ = 30 mT; B T = 100 °C f = 1 MHz; ˆ = 50 mT; B T = 100 °C f = 3 MHz; ˆ = 10 mT; B T = 100 °C E22/R+PLT22/S-3C90 ≥320 − − − − E22/R+PLT22/S-3C92 ≥370 − − − − E22/R+PLT22/S-3C93 ≥320 − − − − E22/R+PLT22/S-3C94 ≥320 − − − − E22/R+PLT22/S-3C95 ≥320 − − − − E22/R+PLT22/S-3C96 ≥320 − − − − E22/R+PLT22/S-3F3 ≥300 − − − − E22/R+PLT22/S-3F35 ≥300 ≤ 2.2 − − − E22/R+PLT22/S-3F4 ≥250 − ≤ 0.62 − ≤ 1.0 E22/R+PLT22/S-3F45 ≥250 − ≤ 0.45 ≤ 1.7 ≤ 0.8 2008 Sep 01 4 Ferroxcube Planar E cores and accessories E22/6/16/R MOUNTING PARTS General data and ordering information ITEM Clamp MATERIAL FIGURE stainless steel (CrNi) TYPE NUMBER 3 CLM-E22/PLT22 R 0.8 max. 5.25 min. olumns 21.4 9 2.5 16.3 min. handbook, halfpage 0.4 8.6 ±0.1 22.2 ±0.3 CBW179 2.8 min. CBW554 16.2 max. 22.4 min. 25.8 min. Dimensions in mm. Dimensions in mm. Fig.4 Fig.3 Clamp for E22/R+PLT22/S. 2008 Sep 01 5 Recommended PCB cut-out for clamped cores. Ferroxcube Planar E cores and accessories E22/6/16/R DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS Preliminary specification Development This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. Design-in These products are recommended for new designs. Preferred These products are recommended for use in current designs and are available via our sales channels. Support These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2008 Sep 01 6