10102 (For use in Series Oscillator Circuits)

CX1H CRYSTAL
10 kHz to 600 kHz
Miniature Quartz Crystal for Series Oscillators
DESCRIPTION
The CX1H quartz crystal is a high quality tuning fork
resonator for use in Series (two cascaded inverters)
oscillators. The CX1H is hermetically sealed in a rugged,
miniature ceramic package, one-fourth the size of an
eight-pin mini-DIP. The CX1H crystal is manufactured
using the STATEK-developed photolithographic process,
and was designed utilizing the experience acquired by
producing millions of crystals for industrial, commercial,
military and medical applications.
actual size
side view
Glass Lid Shown
PACKAGE DIMENSIONS
FEATURES
Miniature tuning fork design
F
E
High shock resistance
Designed for low power applications
Compatible with hybrid or PC board packaging
D
A
Low aging
Full military testing available
Designed and manufactured in the USA
B
C
PACKAGE HANDLING
TYP.
The CX crystal is hermetically sealed in a ceramic package.
Normal handling and soldering precautions for small, low
thermal mass parts are adequate when installing or testing CX
crystals. CX crystals may be wave soldered, with proper
precaution taken to avoid desoldering the leads. A slow
machine rate or too high a pre-heat temperature or solder bath
temperature can damage the crystals. Lead to package
solder interface temperature should not exceed 175oC,
glass lid to package seal rim temperature should not
exceed 210oC. If the seal rim reaches temperatures above the
maximum specified, the package may lose its hermeticity. Loss
of hermeticity results in a frequency decrease and motional
resistance increase.
MAX.
DIM
INCHES
mm
INCHES
mm
A
0.315
8.00
0.330
8.38
B
0.140
3.56
0.155
3.94
C
0.070
1.78
0.080
2.03
D
0.300
7.62
0.310
7.87
E
0.020
0.51
0.040
1.02
F
0.150
3.81
0.160
4.06
Leads 0.013” x 0.018” (0.33 x 0.46 mm) typical.
CONVENTIONAL SERIES
OSCILLATOR CIRCUIT
EQUIVALENT CIRCUIT
C0
OSCILLATOR
CX1H XTAL
1
L1
C1
R1
2
BUFFER
Contact factory for
design guidelines
R1 Motional Resistance L1 Motional Inductance
C1 Motional Capacitance C0 Shunt Capacitance
10102 - Rev C
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
FIGURE 1
CX1H TYPICAL MOTIONAL RESISTANCE (R1)
SPECIFICATIONS
Specifications are typical at 25oC unless otherwise noted.
Specifications are subject to change without notice.
1000
500
Calibration
10 kHz to 600 kHz
Tolerance1
(see below)
Motional Resistance (R1)
Figure 1
MAX.: 2x Typ. @ 10-169.9 kHz
R1 (kV )
Frequency Range
200
100
50
2.5x Typ. @ 170-600 kHz
Motional Capacitance (C1)
Figure 2
20
Quality Factor (Q)
Figure 3
Min. is 0.25x Typ.
10
Shunt Capacitance (C0)
2.0 pF MAX
Drive Level
1.5 µW MAX. @ 10-24.9 kHz
3.0 µW MAX. @ 25-600 kHz
Turning Point (TO
)2
10
Shock, survival3
1,000 G peak 1ms, 1/2 sine
Vibration, survival3
20 G RMS 10-2,000 Hz
Operating Temperature
-10oC to +70oC (Commercial)
-40oC to +85oC (Industrial)
-55oC to +125oC (Military)
Storage Temperature
-55oC to +125oC
Max Process Temperature
See package handling
2
1.0
0.5
600
(in 1000's)
20
10
5
75-169.9
170-249.9
250-600
± 30 ppm
± 50 ppm
±100 ppm
±200 ppm
HOW TO ORDER CX1H LEADED CRYSTALS
I
10
20
50
100
200
600
FIGURE 4
CX1H TYPICAL TURNING POINT TEMP. (T0)
O
10-74.9
“S” if special
or custom
design. Blank
if Std.
100 200
Frequency (kHz)
TO ( C)
Frequency Range (kHz)
/
50
FIGURE 3
CX1H TYPICAL QUALITY FACTOR (Q)
2
30
20
Frequency (kHz)
CX1H Standard Calibration Tolerance at 25oC
32.768K,
10
50
1. Higher frequency calibration available.
2. Other turning point available.
3. Higher shock and vibration available.
03
600
5
C1 (fF)
5ppm MAX.
C
100 200
Figure 4
Aging, first year
S
50
Frequency (kHz)
FIGURE 2
CX1H TYPICAL MOTIONAL CAPACITANCE (C1)
Temperature Coefficient (k) -0.035 ppm/0C2
CX1H
20
+80
+70
+60
+50
+40
+30
+20
+10
0
-10
-20
Side Leads Frequency Calibration Operating Temp. Range:
Tolerance* C = -10OC to +70OC
03 = Non- K = kHz
10
20
50
100 200
600
O
O
@ 25OC I = -40 C to +85 C
RoHS
O
O
Frequency
(kHz)
(in ppm) M = -55 C to +125 C
Compliant
S = Customer Specified
05 = RoHS
Note: Frequency (f) deviation from frequency (fo) @ turning point
Compliant
temperature (To):
2
f-fO
= k(T-TO)
fO
C = Ceramic Lid
Blank = Glass Lid
PACKAGING FOR LEADED CRYSTALS
*The above table provides the best calibration tolerance available
for each frequency range at 25°C.
CX1H
- Tray Pack (Standard)
10102 - Rev C
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com