VCXO 16.384 MHz to 130 MHz Miniature Surface Mount Voltage-Controlled Crystal Oscillator 5mm x 7mm DESCRIPTION Statek’s 5 mm x 7 mm surface mount Voltage-Controlled Crystal Oscillator is designed for applications requiring a highlypullable 3.3 V CMOS-output VCXO with a small footprint. Offered at frequencies from 16.384 MHz to 130 MHz with operation over wide temperature ranges (up to -40°C to +105°C), these VCXOs offer exceptional performance in a small package. Low Profile DIMENSIONS FEATURES High Absolute Pull Range (APR) Low phase noise Low phase jitter Wide frequency range Non-standard frequencies supported Extended Industrial temperature range APPLICATIONS A B C (SM1) C (SM3/SM5) D E Military & Aerospace Avionics Communications Projectiles TERMINATIONS Designation SM1 SM3 SM5 PACKAGE DIMENSIONS Dimension Termination Gold Plated (Pb Free) Solder Dipped Solder Dipped (Pb Free) Minimum mm 6.86 4.85 1.55 1.65 1.19 1.07 Typical mm 7.00 5.00 1.75 1.85 1.40 1.27 Maximum mm 7.16 5.16 1.95 2.05 1.41 1.47 SUGGESTED LAND PATTERN inches (mm) 0.100 (2.54) 0.077 (1.96) ENABLE/DISABLE OPTIONS (T/N) Statek offers two enable/disable options: T and N. The T-version has a Tri-State output and continues to oscillate internally when the output is put into the high Z state. As a result, when re-enabled, the oscillator does not have to restart and an output with a stable frequency resumes almost immediately. The N-version does not have PIN 2 connected internally and so has no enable/disable capability. The following table describes the Enable/Disable option T. 0.144 (3.65) 0.070 (1.80) 0.200 (5.08) PIN CONNECTIONS ENABLE/DISABLE OPTION T FUNCTION TABLE Enable (PIN 1 High*) Disable (PIN 1 Low) Output Frequency Output High Z State Oscillator Oscillates Oscillates Current Normal Lower than normal * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. 1. 2. 3. 4. 5. 6. Control Voltage (Vc) Enable/Disable (T) or not connected (N) Ground Output Not connected (N) Supply Voltage (VDD) STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 10197 REV A ABSOLUTE MAXIMUM RATINGS Supply Voltage VDD Storage Temperature Maximum Process Temperature PACKAGING OPTIONS -0.5 V to 4.6 V -55OC to +125OC 260OC for 10 seconds VCXO - Tray Pack - Tape and reel Per EIA 481 (see Tape and Reel data sheet 10109) SPECIFICATIONS TABLE Parameters listed are at 25°C unless otherwise noted. Parameter Nominal Frequency Symbol F Units MHz T °C Supply Voltage VDD V Current IDD mA CL pF VC V ppm ppm % ms % ns ns V V ps ps dBc/Hz ppm Operating Temperature Minimum 16.384 -40 -40 3.0 1 Output Loading Control Voltage 2 Absolute Pull Range (APR) Linearity Start Up Time Duty Cycle Rise Time Fall Time Logic Low Logic High Period Jitter (rms) Phase Jitter (rms) Phase Noise 3 Aging tr tf VOL VOH J JΦ L Typical Maximum 130 +85 +105 3.6 5 8 14 3.3 Conditions / Comments F ≤ 20 MHz 20 MHz < F ≤ 50 MHz 50 MHz < F ≤ 130 MHz F ≤ 100 MHz. F > 100 MHz. 15 10 0.3 -75 -50 3.0 +75 +50 10 5 60 5 5 0.1 VDD 5 40 0.9 VDD 2.5 0.5 -40°C ≤ T ≤ +85°C -40°C ≤ T ≤ +105°C 45/55 available 3.5 -5 50 MHz (BW = 12 kHz - 20 MHz) See graph below. First year, F ≤ 50 MHz +5 1. Higher CL available. Contact factory. 2. The Absolute Pull Range (APR) is the range of frequencies to which the VCXO can be tuned over the operational temperature range. Expressed in partsper-million (ppm), the reference is the nominal (absolute) frequency F. 3. Tighter aging available. Contact factory. TypicalPhaseNoiseDensity Test Circuit L PhaseNoiseDensity L[dBc/Hz] 0 -20 20MHz 50MHz 130MHz -40 -60 -80 -100 -120 -140 -160 10Hz 100Hz 1kHz 10kHz 100kHz 1MHz Offsetfrequency Note: a 0.1µF bypass capacitor between VDD and GND pins as close as possible is recommended to minimize power supply line noise. HOW TO ORDER VCXO SURFACE MOUNT CRYSTAL OSCILLATORS VCXO A Package Size A = 5 mm x 7 mm 4 T Supply Voltage 3 = 3.0 V 4 = 3.3 V Enable/Disable Option T or N SM3 Terminations Blank = SM1 = Gold Plated (Pb Free) SM3 = Solder Dipped SM5 = Solder Dipped (Pb Free) 130.0M Frequency M = MHz , 75 APR / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC E = -40OC to +105OC STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 10197 REV A