CXOX OSCILLATOR - Statek Corporation

CXOX OSCILLATOR
1 MHz to 160 MHz
Ultra-Miniature Surface Mount
High Frequency Crystal Oscillator
®
Actual View
Top View
DESCRIPTION
Side View
Statek’s ultra miniature and ultra low profile CXOX oscillator
consists of a CMOS/TTL compatible hybrid circuit and a
state-of-the-art, miniature, fundamental-mode crystal.
DIMENSIONS
FEATURES
A
C
Designed for surface mount applications
CMOS and TTL compatible
4
Low power consumption
Full military testing available
3
B
1
E
4
3
TOP
High shock resistance
D
BOTTOM
2
2
1
Optional Output Enable/Disable with Tri-State
Low EMI emission
Hermetically sealed ceramic package
Designed and manufactured in the USA
APPLICATIONS
Military & Aerospace
TYPICAL
MAXIMUM
DIM
inches
mm
inches
mm
A
0.126
3.20
0.136
3.40
B
0.099
2.50
0.107
2.70
0.039
C (SM1)
C (SM3/SM5) 0.044
1.00
1.12
0.043
0.048
1.09
1.21
D
0.040
1.00
0.041
1.10
E
0.030
0.75
0.031
0.85
Long range missiles
Projectile electronics
PIN CONNECTIONS
Smart munitions
1. Output Enable/Disable (E) or no connection (N)
Communications
2. Ground
Navigation
3. Output
GPS
4. VDD
Industrial, Computer & Communications
SUGGESTED LAND PATTERN
Miniature clock oscillator
0.141 (3.6)
Handheld instrumentation
PDA
Transponder/Animal migration
Medical
0.110 (2.9)
0.031 (0.8)
Test & diagnostic equipment
0.039 (1.05)
Handheld devices
0.051
(1.3)
0.039
(1.0)
inches (mm)
IS O
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
90
01
TEM
C ERT I F I C
AT
N
IO
S
10168 Rev A
YS
Pb
SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications below are examples. Specifications are subject
to change without notice. Tighter specifications available.
Please contact factory.
Supply Voltage VDD
-0.5 V to 7.0 V
Storage Temperature
-55OC to 125OC
Maximum Process Temperature 260OC for 20 seconds
Frequency Range1
Supply Voltage
1 MHz to 160 MHz
1.8 V to 5.0 V +_10%
Calibration Tolerance2
+
_
Frequency Stability
Over Temperature3
+
_
Supply Current (Typical)
24 MHz
32 MHz
50 MHz
130 MHz
Output Load (CMOS)4
50 ppm for Commercial
+
_ 100 ppm for Industrial
+
_ 100 ppm for Military
1.8 V
3.3 V
5.0 V
1.5 mA
3.0 mA
8.0 mA
2.0 mA
5.0 mA
10.0 mA
3.0 mA
6.0 mA
13.0 mA
12.0 mA 23.0 mA
39.0 mA
Statek offers two enable/disable options: E and N. The
E-version has a Tri-State output and stops oscillating
internally when the output is put into the high Z state.
The N-version does not have PIN 1 connected internally
and so has no enable/disable capability. The following
table describes the Enable/Disable option E.
ENABLE/DISABLE OPTION E
FUNCTION TABLE
15 pF
Start-up Time
5 ms MAX
Rise/Fall Time
6 ns MAX
5
ENABLE/DISABLE OPTIONS (E/N)
100 ppm
Enable (Pin 1 High*) Disable (Pin 1 Low)
Duty Cycle
40% MIN 60% MAX
Aging, first year
10 ppm MAX
Shock, survival6
5,000 g, 0.3 ms, 1/2 sine
Vibration, survival7
20 g, 10-2,000 Hz swept sine
Operating Temp. Range -10OC to 70OC (Commerical)
-40OC to 85OC (Industrial)
-55OC to 125OC (Military)
Output
Frequency Output
High Z State
Oscillator
Oscillates
Stops
Current
Normal
Very Low
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
PACKAGING OPTIONS
1.
2.
3.
4.
5.
6.
7.
Not all frequencies available at all voltages. Contact factory.
Other tolerances available.
Does not include calibration tolerances. Other tolerances available.
Higher CMOS loads and TTL loads available. Contact factory.
45/55 available upon request in most cases.
Higher shock levels available. Contact factory.
Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load.
CXOX - Tray Pack
- 12 mm tape, 7” or 13” reels
Per EIA 481 (see Tape and Reel data sheet 10109)
HOW TO ORDER CXOX SURFACE MOUNT CRYSTAL OSCILLATORS
CXOX
4
S
N
SM3
Supply Voltage
1 = 1.8 V
2 = 2.5 V
3 = 3.0 V
4 = 3.3 V
5 = 5.0 V
“S” if special or
custom design.
Blank if Std.
Enable/Disable
Option
E or N
Terminations
Blank = SM1
= Gold Plated
(Lead Free)
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
40.0M ,
Frequency
K = kHz
M = MHz
100
/
100
/
Frequency
Stability over
Temp.Range
(in ppm)
Calibration
Tolerance
@ 250C
(in ppm)
I
/
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
OR
/
/
200
Total
Frequency
Tolerance
(in ppm)
/
I
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
IS O
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
90
01
TEM
C ERT I F I C
AT
N
IO
S
10168 Rev A
YS
Pb