DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver General Description Features The AAT3195 is a charge-pump based, current-sink white LED driver capable of driving one to four LEDs up to 30mA, each. It automatically switches between 1x mode and 2x mode to maintain the highest efficiency and optimal LED current accuracy and matching. • Drives up to 4 LEDs at up to 30mA, each • Automatic Switching Between 1x and 2x Modes • 1MHz Switching Frequency • Linear LED Output Current Control ▪ Single-wire, S2Cwire™ Interface • AAT3195-1: 30mA, 32-step • AAT3195-2: 20mA, 32-step ON/OFF or PWM Interface ▪ •AAT3195-3 • ±10% LED Output Current Accuracy • 3% LED Output Current Matching • Low-current Shutdown Mode • Built-in Thermal Protection • Automatic Soft-start • 2x2.2mm SC70JW-10 Package The AAT3195 charge pump’s 1x mode (bypass mode) has very low resistance allowing LED current regulation to be maintained with input supply voltage approaching the LED forward voltage. The AAT3195 incorporates an internal RSET and is available in a thermally enhanced, Pb-free 2x2.2mm 10-lead SC70JW-10 package. Applications • Cordless Phone Handsets • Digital Cameras • Mobile Phone Handsets • MP3 and PMP Players Typical Application Input Voltage 2.7V to 5.5V WLEDs IN CIN 1µF CP 1µF COUT 1µF C+ AAT3195 C- EN/SET S2Cwire Interface OUT D1 D2 EN/SET GND D3 D4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 1 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Pin Descriptions Pin # Symbol 1 D2 2 D1 3 OUT 4 C+ 5 IN EN/SET (AAT3195-1/-2) 6 EN/PWM (AAT3195-3) 7 8 CAGND 9 D4 10 D3 Description LED2 Current Sink Input. D2 is the input of LED2 current sink. Connect LED2’s anode to OUT and its cathode to D2. LED1 Current Sink Input. D1 is the input of LED1 current sink. Connect LED1’s anode to OUT and its cathode to D1. Charge Pump Output. OUT is the output of the charge pump. Bypass OUT to AGND with a 1μF or larger ceramic capacitor. Charge Pump Capacitor Positive Node. Connect a 1μF ceramic capacitor between C+ and C-. Power source input. Connect IN to the power source, typically the battery. Bypass IN to AGND with a 1μF or larger ceramic capacitor. LED Enable and serial control input. EN/SET is the ON/OFF control for the LED and the S2Cwire digital input for the AAT3195-1/-2 to control serially the LED brightness according to the maximum current set by RSET. LED ON/OFF and PWM control input. This logic input controls the LED outputs for the AAT3195-3. Alternatively, a PWM signal from a GPIO or an equivalent signal from a separate controller can be used to control LED output current linearly. A PWM signal, ranging from 10% to 100% duty cycle, controls the LED current linearly between ZS and FS. Charge Pump Capacitor Negative Node. Analog Ground. Connect this pin to the system’s analog ground plane. LED4 Current Sink Input. D4 is the input of LED4 current sink. Connect LED4’s anode to OUT and its cathode to D4. LED3 Current Sink Input. D3 is the input of LED3 current sink. Connect LED3’s anode to OUT and its cathode to D3. Pin Configuration SC70JW-10 (Top View) D2 D1 OUT C+ IN 2 1 10 2 9 3 8 4 7 5 6 D3 D4 AGND CEN/SET (EN/PWM) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Part Number Descriptions Part Number Interface Current Control, Inverting Full Scale Current AAT3195IJQ-1 AAT3195IJQ-2 AAT3195IJQ-3 S2Cwire S2Cwire PWM 32-step 32-step Linear 30mA 20mA 30mA Absolute Maximum Ratings1 Symbol Description VIN, VC+, VC-, VOUT, VDx VEN/SET, VEN/PWM TJ TLEAD IN, C+, C-, OUT, D1, D2, D3, and D4 Pin Voltages to AGND EN/SET or EN/PWM Pin Voltage to AGND Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec) Value Units -0.3 to 6.0 V -0.3 to VIN + 0.3 -40 to 150 300 V °C °C Value Units 625 160 mW °C/W Thermal Information2 Symbol PD ΘJA Description Maximum Power Dissipation Maximum Thermal Resistance 3 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 circuit board. 3. Derate 6.25mW/°C above 40°C ambient temperature. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 3 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Electrical Characteristics IN = EN = 3.6V; CIN = 1µF; COUT = 1µF; CCP = 1µF; TA = -40°C to 85°C unless otherwise noted. Typical values are at TA = 25°C. Symbol Description Conditions AAT3195-1/-2/-3 Input Power Supply IN Input Voltage Range IIN Input Operating Current IIN(SHDN) Input Shutdown Current Charge Pump Section IOUT Maximum Output Current fOSC Charge Pump Oscillator Frequency Charge Pump Mode Hysteresis (AAT3195-1 only) VIN_(TH) Charge Pump Mode Hysteresis (AAT3195-2 only) tOUT Output Start-Up Time AAT3195-1/-2/-3: LED Current Sink Outputs D1 – D4 Current Accuracy (AAT3195-1 only) ID_(MAX) D1 – D4 Current Accuracy (AAT3195-2 only) ΔID_(MAX) ID_(DATA30) ID_(10%) VD_(TH) 4 D1 – D4 Current Matching D1 – D4 Current Accuracy (AAT3195-1 only) D1 – D4 Current Accuracy (AAT3195-2 only) D1 – D4 Current Accuracy (AAT3195-3 only) D1- D4 Charge Pump Mode Transition Threshold (AAT3195-1 only) D1- D4 Charge Pump Mode Transition Threshold (AAT3195-3 only) Min Typ 2.7 EN/SET or EN/PWM = IN; VD1 = VD2 = VD3 = VD4 = IN, excluding ID1-ID4 EN/SET or EN/PWM = IN; ID1 = ID2 = ID3 = ID4 = FS, excluding ID1-ID4; VIN – VF = 1.5V Operating, ID1 = ID2 = ID3 = ID4 = FS; D1, D2, D3 and D4 = OPEN IN = 5.5V; EN/SET or EN/PWM = GND 0.65 150 0.9 Max Units 5.5 V 0.6 mA 3.5 mA 7 mA 1 μA 1.15 mA MHz ID1 = ID2 = ID3 = ID4 = 30mA 225 mV ID1 = ID2 = ID3 = ID4 = 20mA 150 mV EN/SET or EN/PWM ≥ VENH 150 μs DATA = 1; VIN - VF = 1.5V 27 30 33 mA DATA = 1; VIN - VF = 1.5V 18 20 22 mA DATA = 1; VIN - VF = 1.5V ±3 % DATA = 30; VIN - VF = 1.5V 1.672 1.9 2.128 mA DATA = 30; VIN - VF = 1.5V 1.144 1.3 1.456 mA DC = 10%; fPWM = 10kHz; VIN - VF = 1.5V 2.4 mA ID1 = ID2 = ID3 = ID4 = 30mA 250 mV ID1 = ID2 = ID3 = ID4 = 20mA 170 mV Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Electrical Characteristics IN = EN = 3.6V; CIN = 1 µF; COUT = 1µF; CCP = 1µF; TA=-40°C to 85°C unless otherwise noted. Typical values are at TA = 25°C. Symbol Description AAT3195-1/-2: EN/SET and S2Cwire Control VEN(H) EN Input High Threshold Voltage VEN(L) EN Input Low Threshold Voltage IEN(LKG) EN Input Leakage Current tEN/SET(OFF) EN/SET Input OFF Timeout tEN/SET(LAT) EN/SET Input Latch Timeout tEN/SET(LOW) EN/SET Input LOW Time tENSET(H-MIN) EN/SET Minimum High Time tENSET(H-MAX) EN/SET Maximum High Time AAT3195-3: EN/PWM Current Control VEN(H) EN/PWM Input High Threshold Voltage VEN(L) EN/PWM Input Low Threshold Voltage IEN(LKG) EN/PWM Input Leakage Current tPWM(ON) PWM Control Turn-On Delay tEN/PWM EN/PWM Input OFF Timeout fPWM PWM Control Frequency Conditions Min Typ Max 1.4 EN/SET ≥ VEN(H) 0.4 1 500 500 75 -1 0.3 50 75 1.4 EN/PWM = IN = 5V 0.4 1 -1 2 0.15 Duty Cycle = 80% 1 50 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 Units V V μA µs µs µs ns µs V V μA µs ms kHz 5 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Typical Characteristics Quiescent Current vs. Input Voltage No Load Operating Current vs. Input Voltage 4.5 Quiescent Current (mA) Quiescent Current (mA) 0.26 0.25 0.24 0.23 0.22 ° 0.21 0.20 85°C 25°C -40°C 0.19 0.18 2.7 3.1 3.5 3.9 4.3 4.7 5.1 3.9 4.3 4.7 5.1 5.5 D1 D2 D3 D4 34 Current (mA) Efficiency (%) 3.5 (VIN = 3.6V) 60% 40% 20% 32 30 28 26 3.1 3.5 3.9 4.3 4.7 5.1 24 -40 5.5 Input Voltage (V) -15 10 35 60 85 Temperature (°C) AAT3195-2 Efficiency vs. Input Voltage AAT3195-2 Current Matching vs. Temperature (ILED = 20mA; VF = 3.6V) 22.0 100% 90% D1 D2 D3 D4 21.5 80% Current (mA) Efficiency (%) 3.1 36 80% 70% 60% 50% 40% 21.0 20.5 20.0 19.5 30% 3.1 3.5 3.9 4.3 Input Voltage (V) 6 2.7 Input Voltage (V) 100% 20% 2.7 85°C 25°C -40°C 2.5 AAT3195-1 Current Matching vs. Temperature (ILED = 30mA; VF = 4V) 2.7 3.0 AAT3195-1 Efficiency vs. Input Voltage 0% 3.5 2.0 5.5 Input Voltage (V) 4.0 4.7 5.1 19.0 -40 5.5 -15 10 35 Temperature (°C) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 60 85 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Typical Characteristics Turn On to 1X Mode Turn On to 2X Mode (VIN = 4.2V; 20.5mA/ch) (VIN = 3.6V; 20.5mA/ch) EN/SET (2V/div) EN/SET (2V/div) VOUT (2V/div) VOUT (2V/div) VSINK (2V/div) VSINK (2V/div) IIN (200mA/div) IIN (200mA/div) Time (200µs/div) Time (200µs/div) Shutdown Current vs. Temperature Turn Off from 2X Mode (20.5mA/ch) Shutdown Current (µA) 0.14 EN/SET (2V/div) VOUT (1V/div) IIN (200mA/div) 5.5V 2.7V 0.12 0.10 0.08 0.06 0.04 0.02 0.00 -40 Time (200µs/div) 1.0 VEN(H) (V) VEN(L) (V) 1.0 0.8 0.6 85°C 25°C -40°C 3.5 3.9 4.3 Input Voltage (V) 4.7 5.1 60 85 EN Input High Threshold Voltage vs. Input Voltage 1.2 0.4 35 Temperature (°C) 1.2 3.1 10 EN Input Low Threshold Voltage vs. Input Voltage 0.2 2.7 -15 0.8 0.6 85°C 25°C -40°C 0.4 0.2 2.7 5.5 3.1 3.5 3.9 4.3 4.7 5.1 5.5 Input Voltage (V) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 7 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Typical Characteristics EN/SET Input OFF Timeout vs. Input Voltage EN/SET Input Latch Timeout vs. Input Voltage 450 350 300 350 TEN/SET(LAT) (µs) TEN/SET(OFF) (µs) 400 300 250 200 85°C 25°C -40°C 150 100 2.7 3.1 3.5 3.9 4.3 4.7 5.1 200 85°C 25°C -40°C 150 100 2.7 5.5 Input Voltage (V) 250 3.1 3.5 4.7 5.1 5.5 Transition of LED Current (1.3mA to 20.5mA) (20.5mA to 1.3mA) EN (2V/div) EN/SET (2V/div) 4.2V VOUT (1V/div) 4.0V VSINK (1V/div) VSINK (1V/div) 0.5V IIN (50mA/div) IIN (50mA/div) 1.5V Time (100µs/div) Time (100µs/div) AAT3195-1 Output Ripple Waveform AAT3195-2 Output Ripple Waveform (VIN = 3.6V; 2X Mode; 30mA Load) (VIN = 3.6V; 2X Mode; 20.5mA Load) VIN (AC Coupled) (50mV/div) VIN (AC Coupled) (100mV/div) VOUT (AC Coupled) (50mV/div) VOUT (AC Coupled) (100mV/div) VSINK (AC Coupled) (50mV/div) VSINK (AC Coupled) (100mV/div) Time (500ns/div) 8 4.3 Input Voltage (V) Transition of LED Current VOUT (1V/div) 3.9 Time (500ns/div) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Functional Block Diagram C+ IN C– OUT Two-Mode CP Control D1 D2 VF Monitoring 4 D3 D4 AGND IREF EN/SET (EN/PWM) S2Cwire Control (PWM Control) DAC RSET Functional Description S2Cwire Interface (AAT3195-1/-2 Only) The AAT3195 charge-pump solution is designed to drive up to four white LEDs. The charge pump operates from a 2.7V to 5.5V power source and converts it to voltage levels necessary to drive the LEDs. LED current is individually controlled through integrated current sinks powered from the output of the charge pump. Low 1x charge-pump output resistance and low-drop voltage current sinks allow the charge pump to stay in 1x mode with an input voltage as low as 3.75V and LED forward voltages as high as 3.5V. Once in 2x mode, the charge pump monitors the input supply voltage and automatically switches back to 1x mode when there is sufficient input voltage. The LED output current of the AAT3195-1/-2 is controlled by Skyworks' S2Cwire serial interface. Since the LED current is programmable, no PWM or additional control circuitry is needed to control LED brightness. This feature greatly reduces the burden on a microcontroller or system IC to manage LED or display brightness, allowing the user to “set it and forget it.” With its high-speed serial interface (1MHz data rate), the LED current can be changed quickly and easily. Also the non-pulsating LED current reduces system noise and improves LED reliability. The S2Cwire interface relies on the number of rising edges to the EN/SET pin to set the register. A typical write protocol is a burst of EN/SET rising edges, followed by a pause with EN/SET held high for at least tLAT (500μs). The programmed current is then seen at the current sink outputs. When EN/SET is held low for an amount of time longer than tOFF (500μs), the AAT3195-1/-2 enters shutdown mode and draws less than 1μA from the input and the internal data register is reset to zero. The AAT3195 requires only three external components: one 1µF ceramic capacitor for the charge pump flying capacitor (CP), one 1µF ceramic capacitor at the IN pin (CIN), and one 1µF ceramic capacitor at the OUT pin (COUT). The four constant-current outputs of the AAT31951 (D1 to D4) can drive four individual LEDs with a maximum current of 30mA each or, in the case of the AAT3195-2, with a maximum current up to 20mA. Skyworks' single-wire S2Cwire serial interface enables the AAT3195-1/-2 and changes the current sink current in 32 steps through the EN/SET pin. The AAT3195-3 uses an external PWM signal to enable the IC and control the brightness of the LEDs. The AAT3195-1/-2’s serial interface reduces the LED current on each rising pulse of the enable input. If the AAT3195-1/-2 is in shutdown, the first rising edge of the EN/SET input turns on the LED driver to the maximum current. Successive rising edges decrease the LED current as shown in Table 1 and Figure 2 for the AAT3195-1/-2. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 9 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver THI TLO TOFF TLAT EN/SET 1 2 n-1 Data Reg n ≤ 32 0 n 0 Data EN Rising Edges AAT3195-1 D1-D4 Current (mA) AAT3195-2 D1-D4 Current (mA) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 30.0 29.0 28.1 27.1 26.1 25.1 24.2 23.2 22.3 21.3 20.3 19.4 18.4 17.4 16.5 15.5 14.5 13.6 12.6 11.6 10.7 9.7 8.7 7.7 6.8 5.8 4.8 3.9 2.9 1.9 1.0 0.5 20.5 19.8 19.2 18.5 17.8 17.2 16.5 15.8 15.2 14.5 13.9 13.2 12.5 11.9 11.2 10.6 9.9 9.2 8.6 7.9 7.3 6.6 5.9 5.3 4.6 4.0 3.3 2.6 2.0 1.3 0.7 0.3 Dx Output LED Current (mA) Figure 1: S2Cwire Serial Interface Timing. 35 AAT3195-1 AAT3195-2 30 25 20 15 10 5 0 1 3 5 7 9 11 13 15 17 19 21 23 27 29 31 S2Cwire Serial Interface Data Code Figure 2: AAT3195-1/-2 Current Control Profile PWM Control (AAT3195-3 only) PWM (Pulse Width Modulation) is an industry-standard technique of controlling LED brightness by modulating the conduction duty cycle of the LED current. LED brightness is determined by the average value of the PWM signal multiplied by the LED’s intensity where intensity is proportional to the LED drive current. A PWM control signal can be applied to the EN/PWM pin of the AAT31953. By changing the duty cycle of the PWM signal from 100% (logic high) to 10%, LEDs sink current can be programmed from 30mA to 3.0mA. To save power when not used or not needed, the AAT3195-3 can be shut down by holding the EN/PWM pin low for >1ms. Lastly, Table 2 and Figure 3 illustrate the AAT3195-3's LED current control profile as a function of a PWM control signal. Table 1: AAT3195-1/-2 LED Current Setting. 10 25 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver D1-D3 Current (mA) 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 30 27 24 21 18 15 12 9 6 3 30 Dx Output Current (mA) EN/PWM Duty Cycle 25 20 15 10 5 0 100 90 80 70 60 50 40 30 20 10 EN/PWM Input Pin Duty Cycle (%) Table 2: AAT3195-3 LED Current Settings Figure 3: AAT3195-3 Current Control Profile Applications Information LED Selection The AAT3195 is specifically intended for driving white LEDs. However, the device design will allow the AAT3195 to drive most types of LEDs with forward voltage specifications ranging from 2.0V to 4.7V. LED applications may include mixed arrangements for display backlighting, infrared (IR) diodes, and any other load needing a constant current source generated from a varying input voltage. Since the D1 to D4 constant current sinks are matched with negligible voltage dependence, the constant current channels will be matched regardless of the specific LED forward voltage (VF) levels. The low dropout current sinks in the AAT3195 maximize performance and make it capable of driving LEDs with high forward voltages. Multiple channels can be combined to obtain a higher LED drive current without complication. Current sink inputs that are not used should be disabled. To disable and properly terminate unused current sink inputs, they must be tied to OUT. If left unconnected or terminated to ground, the part will be forced to operate in 2x charge pump mode. Device Switching Noise Performance The AAT3195 operates at a fixed frequency of approximately 1MHz to control noise and limit harmonics that can interfere with the RF operation of cellular telephone handsets or other communication devices. Back-injected noise appearing on the input pin of the charge pump is 20mV peak-to peak, typically ten times less than inductor-based DC/DC boost converter white LED backlight solutions. The AAT3195 soft-start feature prevents noise transient effects associated with inrush currents during start-up of the charge pump circuit. Shutdown Since the sink switches are the only power returns for all loads, there is no leakage current when all of the sink switches are disabled. To activate the shutdown mode, hold the EN/SET input low for longer than tOFF (500μs). In this state, the AAT3195 typically draws less than 1μA from the input. Data and address registers are reset to 0 in shutdown. Power Efficiency and Device Evaluation The charge pump efficiency discussion in the following sections accounts only for efficiency of the charge pump section itself. Since the AAT3195 outputs are pure constant current sinks and typically drive individual loads, it is difficult to measure the output voltage for a given output to derive an overall output power measurement. For any given application, white LED forward voltage levels can differ, yet the output drive current will be maintained as a constant. This makes quantifying output power a difficult task when taken in the context of comparing to other white LED driver circuit topologies. A better way to quantify total device efficiency is to observe the total input power Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 11 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver to the device for a given LED current drive level. The best white LED driver for a given application should be based on trade-offs of size, external component count, reliability, operating range, and total energy usage...not just % efficiency. The AAT3195 efficiency may be quantified under very specific conditions and is dependent upon the input voltage versus the output voltage seen across the loads applied to outputs D1 through D4 for a given constant current setting. Depending on the combination of VIN and voltages sensed at the current sinks, the device will operate in load switch mode. When any one of the voltages sensed at the current sinks nears dropout, the device will operate in 2x charge pump mode. Each of these modes will yield different efficiency values. Refer to the following two sections for explanations for each operational mode. 1x Mode Efficiency The AAT3195 1x mode is operational at all times and functions alone to enhance device power conversion efficiency when VIN is higher than the voltage across the load. When in 1x mode, voltage conversion efficiency is defined as output power divided by input power: An expression for the ideal efficiency (η) in 1X chargepump mode can be expressed as: η= -or- POUT VOUT · IOUT VOUT = ≅ PIN VIN · IOUT VIN VOUT η (%) = 100 · V IN 2x Charge Pump Mode Efficiency The AAT3195 contains a fractional charge pump which will boost the input supply voltage in the event where VIN is less than the voltage required to supply the output. The efficiency (η) can be simply defined as a linear voltage regulator with an effective output voltage that is equal to one and one half or two times the input voltage. Efficiency (η) for an ideal 2x charge pump can typically be expressed as the output power divided by the input power. η= 12 In addition, with an ideal 2x charge pump, the output current may be expressed as 1/3 of the input current. The expression to define the ideal efficiency (η) can be rewritten as: η= -or- POUT VOUT · IOUT VOUT = = PIN VIN · 2IOUT 2VIN VOUT η (%) = 100 · 2V IN For a charge pump with an output of 5V and a nominal input of 3.5V, the theoretical efficiency is 71%. Due to internal switching losses and IC quiescent current consumption, the actual efficiency can be measured at 51%. These figures are in close agreement for output load conditions from 1mA to 100mA. Efficiency will decrease substantially as load current drops below 1mA or when the voltage level at VIN approaches the voltage level at VOUT. Capacitor Selection Careful selection of the three external capacitors CIN, CP, and COUT is important because they will affect turn-on time, output ripple, and transient performance. Optimum performance will be obtained when low equivalent series resistance (ESR) ceramic capacitors are used; in general, low ESR may be defined as less than 100mΩ. A value of 1μF for all four capacitors is a good starting point when choosing capacitors. If the constant current sinks are only programmed for light current levels, then the capacitor size may be decreased. Capacitor Characteristics Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the AAT3195. Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor typically has very low ESR, is lowest cost, has a smaller PCB footprint, and is nonpolarized. Low ESR ceramic capacitors help maximizes charge pump transient response. Since ceramic capacitors are non-polarized, they are not prone to incorrect connection damage. POUT PIN Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Equivalent Series Resistance ESR is an important characteristic to consider when selecting a capacitor. ESR is a resistance internal to a capacitor that is caused by the leads, internal connections, size or area, material composition, and ambient temperature. Capacitor ESR is typically measured in milliohms for ceramic capacitors and can range to more than several ohms for tantalum or aluminum electrolytic capacitors. Ceramic Capacitor Materials Ceramic capacitors less than 0.1μF are typically made from NPO or C0G materials. NPO and C0G materials generally have tight tolerance and are very stable over temperature. Larger capacitor values are usually composed of X7R, X5R, Z5U, or Y5V dielectric materials. Large ceramic capacitors (i.e., larger than 2.2μF) are often available in low cost Y5V and Z5U dielectrics, but capacitors larger than 1μF are not typically required for AAT3195 applications. Capacitor area is another contributor to ESR. Capacitors that are physically large will have a lower ESR when compared to an equivalent material smaller capacitor. These larger devices can improve circuit transient response when compared to an equal value capacitor in a smaller package size. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 13 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Evaluation Board Schematic JP6 DC- DC+ C3 1µF J1 1 2 3 VIN JP5 GND 1 2 3 4 5 C2 1µF D1 D2 D3 D4 JP1 JP2 JP3 JP4 10 D2 D3 D1 D4 OUT AGND C+ CIN EN/SET 9 8 7 6 U1 AAT3195 C1 1µF GND GND J2 R6 100 K VIN GND R3 1K Cycle SW3 Up SW2 Down SW1 R2 1K R1 1K U2 1 2 3 4 VDD GP5 GP4 GP3 VSS GP0 GP1 GP2 PIC12F675 VR4 POT10K 8 7 6 C4 1µF R5 1.5k LED2 RED 5 R4 1.5k GND GND LED1 GRN GND GND Evaluation Board Layout 14 Figure 4: AAT3195 Evaluation Board Top Side Layout. Figure 5: AAT3195 Evaluation Board Bottom Side Layout. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Ordering Information Package Interface Current Level, Inverting SC70JW-10 SC70JW-10 SC70JW-10 S Cwire S2Cwire PWM 30mA, 32-step 20mA, 32-step Linear 2 Marking1 Part Number (Tape and Reel)2 3FXYY 3XXYY AAT3195IJQ-1-T1 AAT3195IJQ-2-T1 AAT3195IJQ-3-T1 Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. Package Information SC70JW-10 2.20 ± 0.20 1.75 ± 0.10 0.40 BSC 0.225 ± 0.075 Top View 0.100 7° ± 3° 0.45 ± 0.10 4° ± 4° 0.05 ± 0.05 0.15 ± 0.05 1.10 MAX 0.85 ± 0.15 2.00 ± 0.20 2.10 ± 0.30 Side View End View All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012 15 DATA SHEET AAT3195 Four-Channel Charge Pump LED Driver Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. 16 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202164A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • July 12, 2012