DATA SHEET SMSA7630-061: Surface Mount, 0201 Zero Bias Silicon Schottky Detector Diode Automotive Applications In-Vehicle WiFi @ 2.4 GHz and 5.0 GHz Infotainment Navigation Garage door openers Wireless control systems Telematics Features Description AEC-Q101 qualified The SMSA7630-061 is a silicon, zero bias Schottky detector diode with an ultra-miniature 0201 footprint and very low barrier height. This P-type diode can be used for sensitive video detector circuits and sampling circuits. ISO/TS16949 certified facility Excellent sensitivity Suitable for use up to 77 GHz The low barrier height results in good detector sensitivity without the need for external bias current. The low junction capacitance of this diode makes it an excellent detector at frequencies up to 77 GHz and higher. Low parasitic impedance: CP < 0.05 pF, LS < 0.2 nH Low profile, ultra-miniature 0201 SMT package (MSL1, 260 C per JEDEC J-STD-020) A pinout diagram for the SMSA7630-061 is shown in Figure 1. Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. Bottom View Top View Figure 1. SMSA7630-061 Pinout Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203200B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 7, 2015 1 DATA SHEET • SMSA7630-061: SURFACE MOUNT, 0201 ZERO BIAS SILICON SCHOTTKY DETECTOR DIODE Mixer and Detector Applications 24 GHz Detector Design 24 GHz Rat-Race Mixer A detector circuit that incorporates an SMSA7630-061 Schottky diode and covers the 24 GHz band is shown in Figure 2. The RF arrives on a 50 Ω microstrip line from the left and is shorted to GND by a 90 degree line with a stud (GND arrives by a via). A rat-race mixer that uses two SMSA7630-061 Schottky diodes is shown in Figure 4. The LO signal (24 GHz) is fed from the right side and reaches a rat-race ring. The diodes are positioned 90 degrees apart from the LO input and are terminated in a stub. The cathode of the diode is directly connected to a 24 GHz stub. This output is loaded by a 100 kΩ resistor and a 100 pF capacitor. The output voltage is fed to a 2-pin, 2.54 mm header. Both diodes are connected (using a 1206 resistor) and are loaded by a 470 Ω resistor and a 10 pF capacitor. This forms the IF output (10 MHz). The RF input (24.010 GHz) is directly connected to the rat-race ring. A layout design is illustrated in Figure 5. The circuit was built on a 0.254 mm Rogers RO-4350B substrate and measured with a power-variable 24 GHz source. A layout design is illustrated in Figure 3. Input power versus detected voltage for this detector is shown in Figure 8. The mixer has been tested with the following conditions: LO frequency: LO power: RF frequency: RF power: 24 GHz –4 to +6 dBm 24.010 GHz –30 dBm Typical conversion loss data for this mixer is shown in Figure 9. λ/4 RF Input λ/4 SMS7630-061 Detected Voltage RF Input λ/4 λ/4 3λ/4 LO Input λ/4 SMS7630-061 100 pF λ/4 100 kΩ SMS7630-061 IF Out λ/4 λ/4 100 kΩ 100 pF Figure 2. Schematic of a 24 GHz Detector Design Figure 4. Schematic of a 24 GHz Rat-Race Mixer Figure 3. Layout for a 24 GHz Detector Design Figure 5. Layout for a 24 GHz Rat-Race Mixer Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 May 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203200B DATA SHEET • SMSA7630-061: SURFACE MOUNT, 0201 ZERO BIAS SILICON SCHOTTKY DETECTOR DIODE Electrical and Mechanical Specifications Package and Handling Information The absolute maximum ratings of the SMSA7630-061 are provided in Table 1. Electrical specifications are provided in Table 2. The associated SPICE model parameters are provided in Table 3. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions The PCB layout footprint for the SMS7630-061 is provided in Figure 10. Package dimensions are shown in Figure 11, and tape and reel dimensions are provided in Figure 12. The SMS7630-061 is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Table 1. SMSA7630-061 Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Units Reverse voltage VR Minimum reverse breakdown voltage V Forward current IF 50 mA Power dissipation PD 75 mW Storage temperature TSTG –65 +200 C Operating temperature TA –65 +150 C Electrostatic discharge: ESD 1000 250 <30 V V V Charged Device Model (CDM), Class 4 Human Body Model (HBM), Class 1A Machine Model (MM), Class A Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 2. SMSA7630-061 Electrical Specifications (Note 1) (TA = +25 C, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Breakdown voltage VB IR = 100 μA Total capacitance CT VR = 0.15 V, f = 1 MHz 0.2 pF Video resistance RV 5000 Ω Series inductance LS 0.2 nH Forward voltage VF IF = 0.1 mA IF = 1 mA 1 60 135 V 180 120 240 mV mV Note 1: Performance is guaranteed only under the conditions listed in this table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203200B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 7, 2015 3 DATA SHEET • SMSA7630-061: SURFACE MOUNT, 0201 ZERO BIAS SILICON SCHOTTKY DETECTOR DIODE Table 3. SPICE Model Parameters Parameter Units SMSA7630-061 IS A 5E-06 RS Ω 20 N – 1.05 TT sec 1E-11 CJO pF 0.14 M – 0.4 EG eV 0.69 XTI – 2 Fc – 0.5 BV V 2 IBV A 1E-04 VJ V 0.34 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 May 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203200B DATA SHEET • SMSA7630-061: SURFACE MOUNT, 0201 ZERO BIAS SILICON SCHOTTKY DETECTOR DIODE Typical Performance Characteristics @ 25 °C 0.50 10000 0.45 Detected Voltage (mV) Forward Voltage (V) 0.40 0.35 0.30 0.25 0.20 0.15 0.10 1000 100 10 10 kΩ Video Resistance 100 kΩ Video Resistance 1 0.05 0.1 –40 0 0 2 4 6 8 10 12 14 16 18 20 –30 –20 +10 Figure 7. Detector Voltage vs Input Power Figure 6. Forward Voltage vs Forward Current 20 Conversion Loss (dB) 10000 Output Voltage (mV) 0 Input Power (dBm) Forward Current (mA) 1000 100 10 1 –30 –10 18 16 14 12 10 8 6 –5 –20 –10 0 +10 –3 –1 +1 +3 +5 +7 LO Power (dBm) Input Power (dBm) Figure 8. Output Voltage vs Input Power Figure 9. Conversion Loss vs LO Power Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203200B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 7, 2015 5 DATA SHEET • SMSA7630-061: SURFACE MOUNT, 0201 ZERO BIAS SILICON SCHOTTKY DETECTOR DIODE 0.280 0.400 PCB Pad Metallization 0.200 0.300 Device Outline 0.380 0.100 PCB Solder Mask Opening 0.250 0.200 0.300 Device Outline Stencil Aperture S2030 All measurements are in millimeters Figure 10. SMSA7630-061 PCB Layout Footprint Cathode Terminal (P-Type Device) 0.0236 ± 0.001 (0.600 ± 0.025 mm) 0.0118 ± 0.001 (0.300 ± 0.025 mm) 0.0089 ± 0.001 (0.226 ± 0.025 mm) 0.0065 ± 0.001 (0.165 ± 0.025 mm) 0.0077 ± 0.001 (0.196 ± 0.025 mm) P-Type 0.0007 ± 0.0002 (0.0175 ± 0.005 mm) 0.0107 ± 0.001 (0.273 ± 0.030 mm) Cathode Indicator Must Match Cathode Terminal On The Front Side S1999 Figure 11. SMSA7630-061 Package Dimension Drawing Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 May 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203200B DATA SHEET • SMSA7630-061: SURFACE MOUNT, 0201 ZERO BIAS SILICON SCHOTTKY DETECTOR DIODE ∅1.50 +0.1/–0.0 4.00 ± 0.01 2.00 ± 0.05 A 3.50 ± 0.05 8.00 +0.3/–0.1 1.75 ± 0.10 C 2.00 ± 0.05 B A ∅0.20 ± 0.05 B 0.20 ± 0.05 Cathode Indicator 0.38 ± 0.05 (Ao) 0.70 ± 0.05 (Bo) B Notes: 1. Carrier tape: black conductive polycarbonate bakeable material at 125 °C. 2. Cover tape: transparent conductive material. 3. Cover tape size: 5.4 mm width. 4. ESD surface resistivity meets requirements of GP01-D232. 5. All measurements are in millimeters. C Scale: 5X 0.35 ± 0.05 (Ko) A S2000 Figure 12. SMSA7630-061 Tape and Reel Dimensions Copyright © 2014-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203200B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 7, 2015 7