60A - SynQor

Technical
Specification
BQ35211EEC60
330-365V
11V
60A
600W
4250V
Extended-Eighth Brick
Input
Output
Current
Power
Isolation
DC-DC Converter
The BQ35211EEC60 bus converter is a next-generation,
board-mountable, isolated, fixed switching frequency
DC-DC converter that uses synchronous rectification
to achieve extremely high conversion efficiency.
The Bus Qor series provides an isolated step down
voltage from 352V to 11V intermediate bus with no
regulation in a extended eighth-brick module. The
BQ35211EEC60 converter is ideal for creating the midbus voltage required to drive standard DC-DC nonisolated converters.
BQ35211EEC60 Model
Operational Features
Mechanical Features
• High efficiency, 95% at full rated load current
• Delivers 60A full power with no derating up to 100°C case
• Operating input voltage range: 330-365V
•
•
•
•
• Fixed frequency switching provides predictable EMI
• No minimum load requirement
Extended Eighth-brick package
Industry standard Eighth-brick pin-out configuration
Size: .92”x2.62” (23.4x66.5 mm), height: 0.52” (12.7 mm)
Total Encased weight: 2.2oz (63g)
Protection Features
Control Features
• On/Off control referenced to input side
• Input under-voltage and over voltage lockout protection
against abnormal input voltages
• Inherent current share (by droop method) for high current and
parallel applications.
• Output current limit and short circuit protection (auto recovery)
• Thermal shutdown (auto recovery)
Contents
Safety Features
Page No.
Pending
• UL 60950-1:R2011-12
• EN60950-1/A12:2011
• CAN/CSA-C22.2 No. 60950-1/A1:2011
Product # BQ35211EEC60
Phone 1-888-567-9596
Mechanical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Technical Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Applications Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 1
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Encased Mechanical Diagram
SIDE VIEW
TOP VIEW
.92
[23.4]
.50
[12.7]
.600 [15.24]
.020
[0.51]
.445 [11.3]
4
5
2.000
[50.8]
M3 THREAD
2 PLACES
SEE NOTES 1 & 2
2.120
[53.85]
2.62
[66.5]
SEE NOTE 3
1
2
3
.20 [5.1]
.45
[11.4]
.09 [2.3]
.180
[4.57]
.300 [7.62]
.16
[4.1]
.600 [15.24]
NOTES
PIN DESIGNATIONS
1)M3 SCREWS USED TO BOLT UNIT'S BASEPLATE TO OTHER SURFACES
SUCH AS HEATSINKS MUST NOT EXCEED 0.10" (2.54mm) DEPTH BELOW
THE SURFACE OF THE BASEPLATE.
2)APPLIED TORQUE PER SCREW SHOULD NOT EXCEED 5in-lb (0.7Nm)
3)BASEPLATE FLATNESS TOLERANCE IS 0.004" (.10mm) TIR FOR SURFACE
PINS 1-3 ARE 0.040" (1.02mm) DIA. WITH 0.080" (2.03mm) DIA. STANDOFF
4)SHOULDERS
5)PINS 4 & 5 ARE 0.062" (1.57mm) DIA. WITH 0.100" (2.54mm) DIA. STANDOFF
SHOULDERS
Pin
1
2
3
4
5
Name
Function
Vin(+) Positive input voltage
ON/OFF Logic control ON/OFF
Vin(–)
Negative input voltage
Vout(–) Negative output voltage
Vout(+) Positive output voltage
6)ALL PINS: MATERIAL: COPPER ALLOY
FINISH: MATTE TIN OVER NICKEL PLATE
7)UNDIMENSIONED COMPONENTS ARE SHOWN FOR VISUAL REFERENCE ONLY
8)ALL DIMENSIONS IN INCHES (mm)
TOLERANCES: X.XX IN +/-0.02 (X.X mm +/-0.5 mm)
X.XXX IN +/-0.010 (X.XX mm +/-0.25 mm)
9) WEIGHT: 2.2oz (63g) TYP.
Product # BQ35211EEC60
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 2
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Technical Specification
BQ35211EEC60 Electrical Characteristics
Ta = 25 °C, airflow rate = 800 LFM, Vin = 352V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C base plate
temperature with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Non-Operating
Operating
Isolation Voltage
Input to Output
Input to Base-plate
Output to Base-Plate
Operating Temperature (Baseplate)
Storage Temperature
Voltage at ON/OFF input pin
INPUT CHARACTERISTICS
Operating Input Voltage Range
Product # BQ35211EEC60
-0.5
Max.
Units Notes & Conditions
600
450
V
V
-40
4250
2300
2300
100
Vdc
Vdc
Vdc
°C
-55
-2
125
18
°C
V
365
410
V
V
2.0
V
V
V
V
V
V
A
mA
mA
mA
mA
A
µF
330
330
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Voltage Hysteresis
Input Over-Voltage Shutdown
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Maximum Input Current
No-Load Input Current
Disabled Input Current
Input Reflected-Ripple Current
Input Terminal-Ripple Current
Recommended Input Fuse (see Note 1)
Recommended External Input Capacitance
Input Filter Component Values (L\C)
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
RMS
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Voltage
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
EFFICIENCY
100% Load
50% Load
Typ.
352
352
320
310
10.0
410
420
25
1.0
15
250
30
10
2
4.7\0.22
µH\µF
10.9
V
10.3\1.1
5.6\600
2.8\300
%\V
%\mV
%\mV
V
9.300
Phone 1-888-567-9596
11.400
250
90
0
400
60
mV
mV
A
2,500
A
V
mA
µF
68
8.5
20
95.0
95.9
www.synqor.com
Continuous
Transient, 100 mS; dV/dt > 2 V/µs
Continuous
Transient, 100 ms; dV/dt > 2 V/µs
Vin = 330 V
RMS through 10µH inductor
RMS, full load
Fast blow external fuse recommended
Typical ESR 0.1-0.2 Ω
Internal values
Vin = 352 V, Io = 0 A
Over sample, line, load, temperature & life
20 MHz bandwidth; see Note 2
Full load
Full load
Subject to thermal derating; Vin = 352 V
Vin = 352 V
Vin = 352 V
Negative current drawn from output
10.4 Vout at 30 A Resistive Load
%
%
Doc.# 005-0006545 Rev. A
02/06/14
Page 3
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Technical Specification
BQ35211EEC60 Electrical Characteristics (continued)
Ta = 25 °C, airflow rate = 800 LFM, Vin = 352V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C base plate
temperature with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
DYNAMIC CHARACTERISTICS
Output Voltage during Load Current Transient
Step Change in Output Current (0.1 A/µs)
Settling Time
Turn-On Transient
Turn-On Time (with 2.5 mF output capacitance)
Start-Up Inhibit Time
Output Voltage Overshoot
ISOLATION CHARACTERISTICS
Isolation Voltage (dielectric strength)
Isolation Resistance
Isolation Capacitance (input to output)
Semiconductor Junction Temperature
Board Temperature
Transformer Core Temperature
Maximum Base-Plate Temperature, Tb
FEATURE CHARACTERISTICS
Switching Frequency
ON/OFF Control
On-State Voltage
Off-State Voltage
ON/OFF Control
Pull-Up Voltage
Pull-Up Resistance
Over-Temperature Shutdown OTP Trip Point
Over-Temperature Shutdown Restart Hysteresis
RELIABILITY CHARACTERISTICS
Calculated MTBF (Telcordia) TR-NWT-000332
Calculated MTBF (MIL-217) MIL-HDBK-217F
Field Demonstrated MTBF
Typ.
Max.
250
100
mV
µs
50% to 75% to 50% Iout max
To within 1% Vout nom
5
ms
ms
%
Half load (resistive), Vout=90% nom.
Figure E
2.5 mF load capacitance
4250
See Absolute Maximum Ratings
125
125
125
100
V
MΩ
pF
°C
°C
°C
°C
260
kHz
0.4
18
V
V
2.5
200
0
100
N/A
240
250
-1
2
Units Notes & Conditions
Note 3
Package rated to 150 °C
UL rated max operating temp 130 °C
Application notes Figure B
5
82.5
140
150
10
TBD
TBD
V
kΩ
°C
°C
Average PCB Temperature
106 Hrs. 80% load, 200LFM, 40 °C Ta
106 Hrs. 80% load, 200LFM, 40 °C Ta
106 Hrs. See our website for details
Note 1: Pending certification tests were carried out using 10A fast blow fuse. Fuse interruption characteristics have to be taken into account while
designing input traces. User should ensure that Input trace is capable of withstanding fault currents
Note 2: For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: [email protected])
Note 3: Isolation capacitance can be added external to the module (recommended).
Product # BQ35211EEC60
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 4
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Technical Figures
98
100
95
90
94
Efficiency (%)
Efficiency (%)
96
92
25 C
75 C
88
100.0
80
75
Vin = 230V
70
50C
90
85
Vin = 270V
65
100 C
200.0
300.0
400.0
500.0
Vin = 400V
60
-55ºC
600.0
25ºC
Output Power (W)
100ºC
Case Temperature (ºC)
Figure 1: Efficiency at nominal output voltage vs. output power for nominal
input voltage at different case temperatures.
Figure 2: Efficiency at nominal output voltage and 60% rated power vs. airflow
rate for ambient air temperatures of 25°C, 40°C, and 55°C (nominal input
voltage).
40
50
40
Power Dissipation (W)
Power Dissipation (W)
30
20
25 C
10
Data Pending
30
20
230 Vin
10
50 C
270 Vin
75 C
0
400 Vin
100 C
0.0
100.0
200.0
300.0
400.0
500.0
0
-55ºC
600.0
25ºC
100ºC
Case Temperature (ºC)
Output Power (W)
Figure 3: Power dissipation vs. output power for nominal input voltage at
different case temperatures.
Figure 4: Power dissipation at nominal output voltage and 60% rated power
vs. airflow rate for ambient air temperatures of 25°C, 40°C, and 55°C (nominal
input voltage).
12
60
10
Output Voltage (V)
Output Current (A)
50
40
30
20
Vin = 352 V
10
0
8
6
4
2
25
50
75
100
0
125
Case Temperature (ºC)
Figure 5: Maximum output power vs. case temperature at nominal input voltage.
Product # BQ35211EEC60
Phone 1-888-567-9596
Vin = 352V
0
10
Semiconductor junction temperature is
40
50
60
within 30
1°C of surface
temperature
20
Load Current (A)
70
Figure 6: Output voltage vs. load current, current limit curve for nominal input
voltage at TCASE=25°.
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 5
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Technical Figures
12
Output Voltage (V)
10
8
6
4
2
Vin = 352V
0
0
5
10
15
20
25
30
35
40
45
50
55
60
Load Current (A)
Figure 7: Output voltage vs. load current, regulation curves for nominal input
voltage at TCASE=25°C.
Figure 8: Turn-on transient at no load and zero output capacitance initiated by
ENA. Input voltage pre-applied. Ch 1: Vout (5V/div). Ch 2: ENA (5 V/div).
Figure 9: Turn-on transient at no load and 2.5 mF output capacitance initiated
by ENA. Input voltage pre-applied. Ch 1: Vout (5V/div). Ch 2: ENA (5 V/div).
Figure 10: Turn-on transient at half resistive load and 2.5 mF output
capacitance initiated by ENA. Input voltage pre-applied. Ch 1: Vout (5V/div).
Ch 2: ENA (5 V/div).
Input
Reflected
Ripple
Current
source
impedance
iS
VSOURCE
Figure 11: Turn-on transient at half resistive load and 2.5 mF output
capacitance initiated by Vin. ENA previously high. Ch 1: Vout (5V/div). Ch 2:
Vin (200 V/div).
Product # BQ35211EEC60
Phone 1-888-567-9596
Input
Terminal
Ripple
Current
iC
Output
Voltage
Ripple
DC-DC
Converter
electrolytic
capacitor
VOUT
ceramic
capacitor
tantalum
capacitor
Figure 12: Test set-up diagram showing measurement points for Input Reflected
Ripple Current (Figure 15), Input Terminal Ripple Current (Figure 16) and
Output Voltage Ripple (Figure 17).
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 6
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Technical Figures
Figure 13: Output voltage response to step-change in load current 50%-100%50% of Iout (max). Load capacitance: 1uF ceramic and 10uF 100mΩ ESR
tantalum. Ch1: Vout (500mV/div). Ch 2: Iout (50A/div).
Figure 14: Output voltage response to step-change in load current 10%-100%10% of Iout (max). Load capacitance: 1uF ceramic and 10uF 100mΩ ESR
tantalum. Ch1: Vout (1V/div). Ch 2: Iout (50A/div).
Figure 15: Input reflected ripple current, is, through a 10 µH source inductor,
using a 47µF electrolytic input capacitor (100mA/div). See Figure 12.
Figure 16: Input terminal ripple, ic, at nominal input voltage and full load
(200mA/div). Bandwidth: 20MHz. Load capacitance: 1uF ceramic and 10µF
100mΩ ESR tantalum capacitor. See Figure 12.
Figure 17: Output voltage ripple, Vout, at nominal input voltage and full load
(100mV/div). Bandwidth: 20MHz. Load capacitance: 1uF ceramic and 10µF
100mΩ ESR tantalum capacitor. See Figure 12.
Figure 18: Rise of output voltage after the removal of a short circuit across the
output terminals. Rshort = 5mΩ. Ch1: Vout (5V/div). Ch 2: Iout (20A/div).
Bandwidth: 20MHz.
Product # BQ35211EEC60
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 7
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Applications Section
BASIC OPERATION AND FEATURES
CONTROL FEATURES
With voltages dropping and currents rising, the economics
of an Intermediate Bus Architecture (IBA) are becoming
more attractive, especially in systems requiring multiple
low voltages. IBA systems separate the role of isolation and
voltage scaling from regulation and sensing. The BusQor
series bus converter provides isolation and an unregulated
voltage step down in one compact module, leaving regulation
to simpler, less expensive non-isolated converters.
REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2,
permits the user to control when the converter is on or off.
This input is referenced to the return terminal of the input
bus, Vin(-).
In the negative logic version, the ON/OFF signal is active
low (meaning that a low turns the converter on). Figure B
is a detailed look of the internal ON/OFF circuitry.
In Figure A below, the BusQor module provides the isolation
stage of the IBA system. The isolated bus then distributes
power to the non-isolated buck regulators to generate the
required voltage levels at the points of load. In this case, the
bucks are represented with SynQor’s NiQor series of nonisolated DC-DC converters. In many applications requiring
multiple low voltage outputs, significant savings can be
achieved in board space and overall system costs
When designing an IBA system with bus converters, the
designer can select from a variety of bus voltages. While
there is no universally ideal bus voltage, most designs
employ one of the following: 12V, 11V, 9.6V, 7.5V, 5V, or
3.3V. Higher bus voltages can lead to lower efficiency for the
buck regulators but are more efficient for the bus converter
and provide lower board level distribution current. Lower
bus voltages offer the opposite trade offs.
5V
82.5K
PIN2
PIN3
ON/OFF
10K
TO ENABLE
CIRCUITRY
IN RTN
Figure B: Internal ON/OFF pin circuitry
SynQor’s BusQor modules act as a true dc transformer. The
output voltage is proportional to the input voltage, with a
specified “turns ratio” or voltage ratio, plus minor drop from
the internal resistive losses in the module. When used in
IBA systems, the output variation of the BusQor must be in
accordance with the input voltage range of the non-isolated
converters being employed.
The BusQor architecture is very scalable, meaning multiple
bus converters can be connected directly in parallel to allow
current sharing for higher power applications.
3.3V
48Vdc
Front End
352Vdc
330-365V
BusQor
Converter
2.5V
11.0Vdc
1.8V
1.5V
0.9V
Typical User Board
NiQor
Converters
Loads
Figure A: Example of Intermediate Bus Architecture using BusQor bus converter
and NiQor non-isolated converters
Product # BQ35211EEC60
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 8
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Applications Section
PROTECTION FEATURES
Input Under-Voltage Lockout:The converter is designed
to turn off when the input voltage is too low, helping avoid
an input system instability problem, described in more detail
in the application note titled “Input System Instability”. The
lockout circuitry is a comparator with DC hysteresis. When
the input voltage is rising, it must exceed the typical TurnOn Voltage Threshold value (listed on the specification
page) before the converter will turn on. Once the converter
is on, the input voltage must fall below the typical Turn-Off
Voltage Threshold value before the converter will turn off.
Also see Figure E.
Output Current Limit: The output of the BusQor module
is electronically protected against output overloads. When
an overload current greater than the “DC Current-Limit
Inception” specification is drawn from the output, the
output shuts down to zero volt in a period of 1ms typical
(see Figure C). The shutdown period lasts for a typical
period of 200ms (Figure D) after which the BusQor tries to
power up again (10ms). If the overload persists, the output
voltage will go through repeated cycles of shutdown and
restart with a duty cycle of 4.8% (On) and 95.2% (Off)
respectively. The BusQor module returns (auto resetting)
to normal operation once the overload is removed. The
BusQor is designed to survive in this mode indefinitely
without damage and without human intervention.
Output
Current
68A
60A
Output
Voltage
80 A
peak
Output
Voltage
<11V
0V
Time
210ms
10ms
Figure D: Output Short Circuit and Auto-Resetting protection diagram (not to
scale)
Output Short Circuit Protection: When the output of
the BusQor module is shorted, a peak current of typically
80 A will flow into the short circuit for a period of about
1ms. The output of the BusQor will shutdown to zero for
~ 200mS (Figure D). At the end of the shutdown period
the BusQor module tries to power up again. If the short
circuit persists, the output voltage will go through repeated
cycles of shutdown and restart with a duty cycle of 4.8%
(On) and 95.2% (Off) respectively. The BusQor module
returns (auto resetting) to normal operation once the short
circuit is removed. The BusQor is designed to survive in
this mode indefinitely without damage and without human
intervention.
In the Auto resetting mode, also referred to as “Hiccup”
mode, the power drawn from the 352V input is about 5
Watts, most of which is dissipated into the external fault. It
is important that copper traces and pads from the output
circuit be designed to withstand the short term peaks,
although the average current into the fault may be as low
as 0.015A typical. See Figure 18 for appropriate waveform.
Over-Temperature Shutdown: A temperature sensor
on the converter senses the average temperature of the
module. The thermal shutdown circuit is designed to turn the
converter off when the temperature at the sensed location
reaches the Over-Temperature Shutdown value. It will allow
the converter to turn on again when the temperature of the
sensed location falls by the amount of the Over-Temperature
Shutdown Restart Hysteresis value.
11.0V
0V
1ms
Output
Current
Time
Figure C: Output Overload protection diagram (not to scale)
Product # BQ35211EEC60
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 9
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Applications Section
APPLICATION CONSIDERATIONS
5.0%
At time t2, when the On/Off pin is de-asserted (disabled), the BusQor
output instantly drops to 0V. Fall time from 11.0V to 0V is dependent on
output capacitance and any parasitic trace inductance in the output load
circuit.
At time t3, when the On/Off pin is re-asserted (enabled), the BusQor
module output begins to build up after the inhibit period of 800 ms typical
has elapsed.
Refer to the Control Features section of the data sheet for details on
enabling and disabling methods for Bus Qor modules.
4.0%
Deviation from 50/50 Sharing (%)
Start-Up Inhibit Period: Figure E details the Start-Up Inhibit Period
for the BusQor module. At time t0, when Vin is applied with On/Off pin
asserted (enabled), the BusQor output begins to build up. Before time t1,
when the input voltage is below the UVL threshold, the unit is disabled
by the Input Under-Voltage Lockout feature. When the input voltage rises
above the UVL threshold, the Input Under-Voltage Lockout is released, and
a typical Startup Inhibit Period of 12ms is initiated. The output builds up to
90% of the nominal value of 11.0V in a period of 5ms typical (50 % load).
3.0%
2.0%
1.0%
0.0%
-1.0%
-2.0%
-3.0%
Module 1
-4.0%
-5.0%
Module 2
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
Total Load Current (A)
Figure G: Typical current share performance of 2 paralleled modules
Current Sharing: BusQor modules are designed to operate in parallel
without the use of any external current share circuitry. A typical
(recommended) circuit for paralleling two BusQor modules is shown in
Figure H. An output capacitor is recommended across each module
and located close to the converter for optimum filtering and noise
control performance. Dedicated input inductors are recommended but
are considered optional. Input capacitors must be located close to the
converter module. PCB layout in the input circuit should be such that high
frequency ripple currents of each module is restricted to a loop formed by
the input capacitors and the input terminals of the BusQor module. See
Figure H for details on PCB layout. Contact SynQor application engineering
for further assistance on PCB trace design.
Vin
UVLO
On/Off
(N logic)
OFF
ON
t0
t1
t2
t
t3
Vout
352Vin
BusQor module
CM EMI
filter
Start-up
Inhibit
Fault Inhibit
(Not shown
in Figure H)
Time
Start-Up
Figure E: Power Up/Down Diagram (not to scale) showing Start-Up Inhibit
Period
Bulk
Cap
BusQor module
Input LC filters
Figure H: Recommended physical implementation of two Bus Qor's in parallel.
The current share performance of two paralleled modules is illustrated
in the graph in Figure G. In this graph the percent deviation from ideal
sharing (50%) is plotted for each module versus the total output load
current at 352Vin.
Product # BQ35211EEC60
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 10
Input: 330-365V
Output: 11V
Current: 60A
Package: EXT-Eighth Brick
Ordering Information
Part Numbering System
Ordering Information
The part numbering system for SynQor’s dc-dc converters follows the format
shown in the example below.
The tables below show the valid model numbers and ordering options for
converters in this product family. When ordering SynQor converters, please
ensure that you use the complete 15 character part number consisting of
the 12 character base part number and the additional characters for options.
Add “-G” to the model number for 6/6 RoHS compliance.
BQ 3 5 2 1 1 E E C 6 0 N R S - G
6/6 RoHS
Options
(see
Ordering Information)
Model Number
Input Voltage
BQ35211EEC60xyz-G
330-365V
Output
Voltage
11V
Max Output
Current
60A
Output Current
Thermal Design
Extended Package Size
The following options must be included in place of the w x y z spaces in the
model numbers listed above.
Output Voltage
Input Voltage
Product Family
Thermal Design
ENCASED
The first 12 characters comprise the base part number and the last 3
characters indicate available options. The “-G” suffix indicates 6/6 RoHS
compliance.
Options Description: w x y z
Enable Logic
Pin Style
N - Negative
K - 0.110"
N - 0.145"
R - 0.180"
Y - 0.250"
Feature Set
S - Standard
Not all combinations make valid part numbers, please contact SynQor for
availability.
Application Notes
A variety of application notes and technical white papers can be downloaded
in pdf format from our website.
RoHS Compliance: The EU led RoHS (Restriction of Hazardous
Substances) Directive bans the use of Lead, Cadmium, Hexavalent
Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated
Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor
product is 6/6 RoHS compliant. For more information please refer to
SynQor’s RoHS addendum available at our RoHS Compliance / Lead Free
Initiative web page or e-mail us at [email protected].
PATENTS
SynQor holds the following U.S. patents, one or more of which apply to
each product listed in this document. Additional patent applications may
be pending or filed in the future.
Contact SynQor for further information and to order:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
Product # BQ35211EEC60
978-849-0600
888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
5,999,417
6,222,742
6,545,890
6,577,109
6,594,159
6,731,520
6,894,468
6,896,526
6,927,987
7,050,309
7,072,190
7,085,146
7,119,524
7,269,034
7,272,021
7,272,023
7,558,083
7,564,702
7,765,687
7,787,261
8,023,290
8,149,597
8,493,751
Warranty
SynQor offers a three (3) year limited warranty. Complete warranty
information is listed on our website or is available upon request from
SynQor.
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
www.synqor.com
Doc.# 005-0006545 Rev. A
02/06/14
Page 11