WSH420

WSH420
Single Coil Hall Effect IC with Thermal Lock
Protection and Auto-Restart
Features:
Operate from 2.4V to 15V supply voltage.
On-chip Hall sensor.
Internal bandgap regulator allows temperature compensated operations and a
wide operating voltage range.
Output sinking capability up to 450mA for driving large load.
Lower current change rate reduces the peak output voltages during switching.
Available in rugged low profile SIP-4L packages.
Built-in protection resistance for reverse power supply fault.
Built-in thermal lock protection and auto-restart function.
General Description:
WSH420 is designed to integrate Hall sensor with two push-pull output drivers and
frequency generator together on the same chip, it is suitable for single coil DC
brushless motors. It includes a temperature compensated voltage regulator, a
differential amplifier, a Hysteresis controller, complementary bi-direction drivers for
sinking and driving large current load. An on-chip protection resistor is implemented
to prevent reverse power fault. And built-in thermal lock protection and auto-restart
function will automatically shutdown power at 120°C to prevent the coils be damaged
during high temperature and auto-restart at 115°C. It can replace the function of lock
protection and auto-restart at low cost.
WSH420 are rated for operation over temperature range from –20˚ C to 85˚C and
voltage ranges from 2.4V to 15V.
Pin Descriptions: (SIP-4L)
Name
P/I/O
Pin#
Vcc
P
1
DOB
O
2
DO
O
3
Vss
P
4
Description
Positive Power Supply
Output Pin #1
Output Pin #2
Ground
Winson reserves the right to make changes to improve reliability or manufacturability.
©Winson, 2005/9/23
1
WSH420
Absolute Maximum Rating (at Ta=25˚ C)
Supply Voltage
Vcc -------------------------Magnetic flux density
B -------------------------Reverse Protection Voltage
Vr -------------------------Output Lock Current
Ic --------------------------
15V
Unlimited
15V
450mA
Operating Temperature Range
Storage Temperature Range
Package Power Dissipation
(-20˚C to +85˚C)
(-65˚C to +150˚C)
500mw for SIP-4L
Ta -------------------------Ts -------------------------Pd --------------------------
Electrical Characteristics:
(T=+25˚C, Vcc=2.4V to 15V)
Characteristic
Symbol Test Conditions
Min
Typ Max Units
Supply Voltage
Vcc
V
─
2.4
─
15
Output Saturation Vout(sat) Vcc=12V, Io=200mA ─
V
0.6
1.0
Vdrive+Vsink
Voltage
Output Leakage
Ileakage Vcc=12V, B < Brp
uA
─
<0.1
10
Current
Supply Current
Isupply Vcc=12V, Io=200mA ─
mA
22
30
FG “ON”
Function Block:
Winson reserves the right to make changes to improve reliability or manufacturability.
©Winson, 2005/9/23
2
WSH420
Magnetic Characteristics:
Characteristics
Symbol
Operate Point
Bop
Release Point
Brp
Hysteresis Window
Quantity
Ta= -20˚C to +90˚C
Min
Typ.
Max
A
Grade B
C
A -50
Grade B -70
C -120
Bop-Brp
35
50
Ordering Information:
SIP -4L: WSH420-XPAN□
Elec. Grade
Elec. Grade
SIP-4L:
1: A Grade (50 Gauss)
2: B Grade (70 Gauss)
3: C Grade (120 Guass)
Winson reserves the right to make changes to improve reliability or manufacturability.
©Winson, 2005/9/23
3
50
70 Gauss
120
-35
-50
40
Unit
Gauss
80
Gauss
WSH420
Testing Circuit
Winson reserves the right to make changes to improve reliability or manufacturability.
©Winson, 2005/9/23
4
WSH420
Package Information:
1. SIP-4L
Winson reserves the right to make changes to improve reliability or manufacturability.
©Winson, 2005/9/23
5
WSH420
Application Circuit:
Figure 1.
Winson reserves the right to make changes to improve reliability or manufacturability.
©Winson, 2005/9/23
6