Application Notes - recom

Application Notes
SPECIFICATION CHECKLIST
Use this checklist to help you define your specification. If you can’t find a converter that fulfils your
needs then call us, fax us, e-mail us or use our Web Sample Enquiry link and we will find the best
match for you.
1.
c Non-Isolated
c Isolation Required _____kVDC or ____kVAC
2.
c Single Output
c Dual Bipolar Output
c Other:
Output Voltages (V) _____ /______/______
Output Currents (A) _____/______/______
3.
Total Output Power (V x A) _________________
4.
c Regulated
5.
Short Circuit Protection: c No c Yes
6.
Remote Control Pin: c No c Yes
7.
Output Voltage Trim: c No c Yes
8.
Input Voltage: minimum ______ maximum ______
9.
Mounting Style: c Through Hole
c Unregulated
c SMD
Single-In-Line Pins c SIP4 c SIP6 c SIP7
c SIP8
c SIP12
Dual-In-Line Pins c DIP8 c DIP14 c DIP16 c DIP24 - Pinout? A_B_C_
Standard Brick
c 1” x 1” c 1” x 2” c 1.6” x 2” c 2” x 2”
Case Style: c Metal Case
c Plastic Case
c Open Frame
10.
Certifications Required: c None c EN 60950-1 c EN 60601-1 c UL 60950-1
11.
Operating Temperature Range: minimum ______ maximum ______
12.
Heatsink required : c No c Yes
13.
Other Requirements:________________________________________
REMEMBER: THERE IS AN INTERACTIVE SELECTION GUIDE ON OUR WEBSITES
RECOM makes every effort to ensure that the
specifications in this catalogue are complete
and accurate. RECOM reserves the right to
alter or improve the specification, internal design or manufacturing process at any time,
APP NOTES
without notice. Please check with your
supplier that you have the most current and
complete specification for your product
before use. Customers may check that they
have the most up to date datasheets by
2014
visiting the RECOM website at:
www.recom-international.com
www.recom-power.com,
www.recom-asia.com or by calling or sending an e-mail to RECOM Technical Support.
www.recom-international.com
Application Notes
CHOOSING THE RIGHT CONVERTER: A GUIDE for DC/DC Converters
Step 1:
Do you need Isolation? (An isolated converter has outputs that are floating and not
connected to the inputs i.e. they are galvanically isolated)
No isolation needed: Check our Innoline parts first (R-78 series, R-5xxx, R-6xxx and
R-7xxx series)
Isolation needed: decide whether you need 1kVDC/1 sec (standard) or 1.6VDC/
1 sec, 2kVDC/1 sec, 3kVDC/1 sec, 4kVDC/1 sec, 5.2kVDC/1 sec or 6kVDC/1 sec.
Step 2:
Decide on the output voltage and number of outputs: single, dual bipolar (+/-), dual
isolated or triple.
It is also important to decide whether the output voltage needs to be regulated or
unregulated.
Unregulated converters are offered standard without short circuit protection or
optionally with short circuit protection (option /P)
All Series are available with single outputs.
Please note that a dual output converter can be used as a single output by leaving
the common pin unconnected i.e. +/-5V = 10V, +/-12V = 24V, +/-15V = 30V, etc.
Step 3:
Decide on the output current. The output voltage times the output current gives the
output power of the converter in Watts.
DC/DC converters are designed to run at full load, so only round up the power if a
suitable converter is not available.
e.g. 5V @ 150mA = 0.75W = 1W converter.
e.g. +/-15V @ +/-1A = 30W = 30W converter.
Step 4:
Decide on the input voltage. Standard input voltage ranges are:
3.3, 5, 9, 12, 15, and 24VDC with +/-10% tolerance
4.5 ~ 9V, 9 ~ 18V, 18 ~ 36V and 36 ~ 72VDC with 2:1 input voltage range
9 ~ 36V and 18 ~ 72VDC with 4:1 input voltage range.
Step 5:
Decide on the case style and pin-out. Many Recom series are available in either
through hole or surface mount styles and with several pin-out options, including
Remote On/Off Control.
Step 6:
Use either the Selection guide or Contents guide at the start of each section to
find the most appropriate converter.
REMEMBER: THERE IS AN INTERACTIVE SELECTION GUIDE ON OUR WEBSITES
RECOM makes every effort to ensure that the
specifications in this catalogue are complete
and accurate. RECOM reserves the right to
alter or improve the specification, internal design or manufacturing process at any time,
www.recom-international.com
without notice. Please check with your
supplier that you have the most current and
complete specification for your product
before use. Customers may check that they
have the most up to date datasheets by
2014
visiting the RECOM website at:
www.recom-international.com
www.recom-power.com,
www.recom-asia.com or by calling or sending an e-mail to RECOM Technical Support.
APP NOTES
Application Notes
Contents
ECONOLINE (General Apps.)
●
Pre- and Post Regulation
●
Output Voltage Accuracy
Terminology
EIA-232 Interface
●
Voltage Balance
Input Range
3V/5V Logic Mixed Supply Rails
●
Line Regulations
Load Regulation
Isolated Data Acquisition System
●
Load Regulation
EMC Considerations
●
Efficiency
Output Voltage Accuracy
Power Supply Considerations
●
Switching Frequency
Input and Output Ripple and Noise
Interpretation of DC-DC Converter EMC Data
●
Output Ripple and Noise
Input to Output Isolation
Conducted and Radiated Emissions
●
Output Ripple and Noise (continued)
Insulation Resistance
Line Impedance Stabilisation Network (LISN)
●
Transient Recovery Time
Efficiency at FulI Load
Shielding
●
Current Limiting
Temperature Drift
Line Spectra of DC-DC Converters
●
Fold Back Current Limiting
Line Voltage Regulation
●
Switching Frequency
●
Temperature Performance of DC-DC Converters
●
Isolation
No Load Power Consumption
●
Transfer Moulded (SMD) DC-DC Converters
●
Break-Down Voltage
Isolation Capacitance
Production Guideline Application Note
●
Temperature Coefficient
Mean Time Between Failure (MTBF)
Component Materials
●
Ambient Temperature
Noise
Component Placement
●
Operating Temperature Range
Operating Temperature Range
Component Alignment
●
Storage Temperature Range
Calculation of Heatsinks
Solder Pad Design
●
Output Voltage Trimming
Isolation
Solder Reflow Profile
●
Heat Sinks
Isolation Voltage vs. Rated Working Voltage
Recommended Solder Reflow Profile
POWERLINE AC/DC
●
Isolation mode in IGBT Driver Circuits
Adhesive Requirements
●
Connecting DC-DC Converters in Series
Adhesive Placement
●
Connecting DC-DC Converters in Parallel
Cleaning
●
Chaining DC-DC Converters
Vapour Phase Reflow Soldering
●
Filtering
●
●
Tin Whisker Mitigation
●
Input Fuse
●
Earthing
●
External Filter
●
Paralleling AC/DC Converters
●
Chaining Converters
●
DC Inputs
Output Filtering Calculation
●
Limiting Inrush Current
●
Maximum Output Capacitance
●
Settling Time
●
Isolation Capacitance and Leakage Current
●
Application Examples
Overload Protection
Input Voltage Drop-Out (brown-outs)
INNOLINE
●
EMC Filter Suggestion
●
Soft Start Circuit
●
Positve - to - Negative Converters
POWERLINE DC-DC
●
EMC Filter Suggestion
●
General Test Set-Up
●
Input Voltage Range
●
PI Filter
No Load Over Voltage Lock-Out
POWERLINE PLUS
●
IEC Technology
●
Trim Tables
●
Block Diagrams
BLOCK DIAGRAMS
Long Distance Supply Lines
LCD Display Bias
APP NOTES
2014
Transport Tubes & Reels
www.recom-international.com
DC-DC Converter Applications
Terminology
The data sheet specification for DC-DC converters contains a large quantity of information.
This terminology is aimed at ensuring that the
user can interpret the data provided correctly
and obtain the necessary information for their
circuit application.
Input Range
The range of input voltage that the device can
tolerate and maintain functional performance
over the Operating Temperature Range at full
load.
Load Regulation
The change in output voltage over the specified
change in output load. Usually specified as a
percentage of the nominal output voltage, for
example, if a 1V change in output voltage is
measured on a 12V output device, load voltage
regulation is 8.3%. For unregulated devices
the load voltage regulation is specified over
the load range from 10% to 100% of full
load.
Line Voltage Regulation
The change in output voltage for a given
change in input voltage, expressed as percentages. For example, assume a 12V in-put, 5V
output device exhibited a 0.5V change at the
output for a 1.2V change at the input, line
regulation would be 10%/10%.
Output Voltage Accuracy
The proximity of the output voltage to the
specified nominal value. This is given as a
tolerance envelope for unregulated devices
with the nominal input voltage applied. For example, a 5V specified output device at 100%
load may exhibit a measured output voltage of
4.75V, i.e. a voltage accuracy of –5%).
Input and Output Ripple and Noise
The amount of voltage drop at the input, or
output between switching cycles. The value of
voltage ripple is a measure of the storage
ability of the filter capacitors. The values given
in the datasheets include the higher frequency
Noise interference superimposed on the ripple
due to switching spikes.The measurement is
limited to 20MHz Bandwidth.
Input to Output Isolation
The dielectric breakdown strength test between
input and output circuits. This is the isolation
voltage the device is capable of withstanding
for a specified time, usually 1 second (for more
details see chapter “Isolation Voltage vs. Rated
Working Voltage”).
www.recom-international.com
Insulation Resistance
The resistance between input and output
circuits. This is usually measured at 500V DC
isolation voltage.
Efficiency at FulI Load
The ratio of power delivered from the device to
power supplied to the device when the part is
operating under 100% load conditions at 25°C.
Temperature Drift
The change in voltage, expressed as a
percentage of the nominal, per degree change
in ambient temperature. This parameter is
related to several other temperature dependent
parameters, mainly internal component drift.
Switching Frequency
The nominal frequency of operation of the
switching circuit inside the DC-DC converter.
The ripple observed on the input and output
pins is usually twice the switching frequency,
due to full wave rectification and the push-pull
configuration of the driver circuit.
No Load Power Consumption
This is a measure of the switching circuits
power cunsumption; it is determined with zero
output load and is a limiting factor for the total
efficiency of the device.
Isolation Capacitance
The input to output coupling capacitance. This
is not actually a capacitor, but the parasitic
capacitive coupling between the transformer
primary and secondary windings. Isolation
capacitance is typically measured at 1 MHz to
reduce the possibility of the on-board filter
capacitors affecting the results.
Mean Time Between Failure (MTBF)
RECOM uses MIL-HDBK-217F standard for
calculation of MTBF values for +25°C as well as
for max. operating temperature and 100% load.
When comparing MTBF values with other
vendor's products, please take into account the
different conditions and standards i.e. MILHDBK-217E is not as severe and therefore values
shown will be higher than those shown by RECOM.
(1000 x 10³ hours =1000000 hours = 114 years!)
These figures are calculated expected device
lifetime figures using the hybrid circuit model of
MIL-HDBK-217F. POWERLINE converters also
can use BELLCORE TR-NWT-000332 for
calculation of MTBF. The hybrid model has
various accelerating factors for operating
environment (πE), maturity (πL), screening (πQ),
hybrid function (πF) and a summation of each
individual component characteristic (λC).
2014
The equation for the hybrid model is then given
by:
λ = Σ (NC λC) (1 + 0.2πE) πL πF πQ
(failures in 106 hours)
The MTBF figure is the reciprocal of this value.
In the data sheets, all figures for MTBF are
given for the ground benign (GB) environment
(πE = 0.5); this is considered the most
appropriate for the majority of applications in
which these devices are likely to be used.
However, this is not the only operating
environment possible, hence those users
wishing to incorporate these devices into a
more severe environment can calculate the
predicted MTBF from the following data.
The MIL-HDBK-217F has military environments specified, hence some interpretation of
these is required to apply them to standard
commercial environments. Table 1 gives
approximate cross references from MIL-HDBK217F descriptions to close commercial equivalents. Please note that these are not implied
by MIL-HDBK-217F, but are our interpretation.
Also we have reduced the number of environments from 14 to 6, which are most appropriate to commercial applications. For a more
detailed understanding of the environments
quoted and the hybrid model, it is
recommended that a full copy of MIL-HDBK217F is obtained.
It is interesting to note that space flight and
ground benign have the same environment
factors. It could be suggested that the act
of achieving space flight should be the
determining environmental factor (i.e. missile
launch).
The hybrid model equation can therefore be
rewritten for any given hybrid, at a fixed
temperature, so that the environmental factor
is the only variable:
λ = k (1 + 0.2 πE)
The MTBF values for other environment factors
can therefore be calculated from the ground
benign figure quoted at each temperature point
in the data book. Hence predicted MTBF
figures for other environments can be calculated very quickly. All the values will in general
be lower and, since the majority of the mobile
environments have the same factor, a quick
divisor can be calculated for each condition.
Therefore the only calculation necessary is to
devide the quoted MTBF fig. by the divisor
given in table 2.
A-1
DC-DC Converter Applications
Environment
Ground
Benign
πE
Symbol
GB
Ground
Mobile
GM
Naval
Sheltered
NS
Aircraft
Inhabited
Cargo
AIC
Space
Flight
SF
Missile
Launch
ML
MIL-HDBK-271F
Description
Non-mobile, temperature and
humidity controlled environments
readily accessible to maintenance
Equipment installed in wheeled or
tracked vehicles and equipment
manually transported
Sheltered or below deck
equipment on surface ships or
submarines
Typical conditions in cargo
compartments which can be
occupied by aircrew
Earth orbital. Vehicle in neither
powered flight nor in atmospheric
re-entry
Severe conditions relating
to missile launch
Commercial Interpretation
or Examples
Laboratory equipment, test
instruments, desktop PC's,
static telecomms
In-vehicle instrumentation,
mobile radio and telecomms,
portable PC's
Navigation, radio equipment
and instrumentation below
deck
Pressurised cabin compartments and cock-pits, in flight
entertainment and non-safety
critical applications
Orbital communications satellite, equipment only operated
once in-situ
Severe vibrational shock and
very high accelerating forces,
satellite launch conditions
VO
DC
VIN
DC
GND
0V
a) Single Output
DC
VIN
+VO
0V
-VO
DC
GND
b) Dual Output
VIN
GND
VO1
0V1
VO 2
0V2
DC
DC
c) Twin Isolated Outputs
Table 1: Interpretation of Environmental Factors
Figure 1: Standard Isolated Configurations
Environment
Ground Benign
Ground Mobile
Naval Sheltered
Aircraft
Inhabited
Cargo
Space Flight
Missile Launch
πE
Symbol
GB
GM
GNS
πE Divisor
Value
0.5
1.00
4.0
1.64
4.0
1.64
AIC
4.0
1.64
SF
ML
0.5
12.0
1.00
3.09
Table 2: Environmental Factors
Noise
Input conducted noise is given in the line
conducted spectra for each DC-DC converter
(see EMC issues for further details). Noise is
affected significantly by PCB layout, measurement system configuration, terminating
impedance etc., and is difficult to quote
reliably and with any accuracy other than via a
spectrum analysis type plot. There will be some
switching noise present on top of the ripple,
however, most of this is easily reduced by use
of small capacitors or filter inductors, as shown
in the application notes.
Operating temperature range:
Operating temperature range of the converter
is limited due to specifications of the
components used for the internal circuit of the
converter.
The diagram for temperature derating shows
the safe operating area (SOA) within which the
device is allowed to operate. At very low
temperatures, the specifications are only
guaranteed for full load.
Up to a certain temperature 100% power can
be drawn from the device, above this temperature the output power has to be less to
ensure function and guarantee specifications
over the whole lifetime of the converter.
These temperature values are valid for natural
convection only. If the converter is used in a
closed case or in a potted PCB board, higher
temperatures will be present in the area around
thermal converter because the convection may
be blocked.
If the same power is also needed at higher
temperatures either the next higher wattage
series should be chosen or if the converter has
a metal case, a heatsink may be considererd.
Please refer to the Powerline Application Notes
Section for more information on thermal
impedance and heatsinking.
A-2
2014
VCC
+VO
DC
DC
-VO
0V
GND
a) Non-lsolated Dual Rails
VCC
DC
DC
+VO
0V
-VO
GND
b) Non-lsolated Negative Rail
VCC
DC
DC
+VO
(VO+VIN)
0V
GND
c) Non Isolated Voltage Booster
Figure 2: Alternative Supply Configurations
www.recom-international.com
DC-DC Converter Applications
Isolation
One of the main features of the majority of
Recom DC-DC converters is their high galvanic
isolation capability. This allows several variations
on circuit topography by using a single DC-DC
converter.
bias, resistor feed). Having an alternative return
path can upset the regulation and the
performance of the system may not equal that
of the converter.
The basic input to output isolation can be used
to provide either a simple isolated output power
source, or to generate different voltage rails,
and/or dual polarity rails (see figure 1).
These configurations are most often found in
instrumentation, data processing and other
noise sensitive circuits, where it is necessary
to isolate the load and noise presented to the
local power supply rails from that of the entire
system. Usually local supply noise appears as
common mode noise at the converter and does
not pollute the main system power supply rails.
The isolated positive output can be connected
to the input ground rail to generate a negative
supply rail if required. Since the output is
isolated from the input, the choice of reference
voltage for the output side can be arbitrary, for
example an additional single rail can be
generated above the main supply rail, or offset
by some other DC value (see figure 2).
Regulated converters need more consideration
than the unregulated types for mixing the
reference level. Essentially the single supply rail
has a regulator in its +Vout rail only, hence
referencing the isolated ground will only work if
all the current return is through the DC-DC and
not via other external components (e.g. diode
Isolation Voltage vs. Rated Working Voltage
The isolation voltage given in the datasheet is
valid for 1 second flash tested only.
If a isolation barrier is required for longer or
infinite time the Rated Working Voltage has to
be used.
Conversion of Isolation Voltage to Rated
Working Voltage can be done by using this
table or graph.
IEC950 Test Voltage for Electrical Strength Tests
Isolation Test Voltage (V)
Rated Working Voltage (V)
1000
130
1500
230
3000
1100
6000
3050
Table 2: Typical Breakdown Voltage Ratings According to IEC950
The graph and table above show the requirements from IEC950. According to our experience and in-house tests, we can offer the following conversion
tables. Please note that these equivalence tables are for information only and that RECOM assumes no resposibility for their use:
DC
1 Sec
1 Min
500VDC
400VDC
1000VDC
800VDC
1500VDC
AC
1 Sec
1 Min
350VAC
250VAC
130VDC
700VAC
500VAC
130VAC
1200VDC
230VDC
1080VAC
750VAC
230VAC
2kVDC
1.6kVDC
550VDC
1.4kVAC
1kVAC
550VAC
3kVDC
2.4kVDC
1.1kVDC
2.1kVAC
1.5kVAC
1.1kVAC
4kVDC
3.2kVDC
1.8kVDC
2.8kVAC
2kVAC
1.8kVAC
6kVDC
4.8kVDC
3kVDC
4.2kVAC
3kVAC
3kVAC
8kVDC
6.4kVDC
4kVDC
5.6kVAC
4kVAC
4kVAC
10kVDC
8kVDC
5kVDC
7kVAC
5kVAC
5kVAC
www.recom-international.com
Cont.
2014
Cont.
A-3
DC-DC Converter Applications
Isolation mode in IGBT driver circuits
An application for DC/DC converters is to isolate driver circuits for IGBT stacks. In these applications, the maximum DC voltage applied across the
isolation gap is not the only factor to be considered because the highly dynamic switching waveforms are an additional stressing factor (typical
switching transients can exceed 20kV/µs.) Taking into account that both factors mean a permanent stress on the converter, it is recommended to
over specify the converter in terms of isolation voltage and coupling capacitance.
Even if a 3kVDC product seems to be appropriate if you just look at the rated working voltage that is required, it is still recommended to choose a
product which is specified to 5.2kVDC or 6kVDC to also cover the high dv/dt rates. The higher the isolation voltage rating for a DC/DC converter is,
the lower the coupling (isolation) capacitance and a low coupling capacitance is essential in AC or highly dynamic switched DC usage. This will
ensure a safe usage and avoid a shortened lifetime in such a highly demanding situation.
In the example below, A RP-0524S is used to provide a 5200V isolated supply for the high side drivers and a second, non-isolated converter is
used to boost the 5V supply voltage up to 15V for the low side drivers.
Connecting
DC-DC Converters in Series
Galvanic isolation of the output allows multiple
converters to be connected in series, simply by
connecting the positive output of one converter
to the negative of another (see figure 3). In this
way non-standard voltage rails can be
generated, however, the current output of the
highest output voltage converter should not be
exceeded.
When converters are connected in series,
additional filtering is strongly recommended, as
the converters switching circuits are not
synchronised. As well as a summation of the
ripple voltages, the output could also produce
relatively large beat frequencies. A capacitor
across the output will help, as will a series
inductor (see filtering).
Vcc
DC
DC
DC
DC
+Vo
0V
+Vo
2Vo
0V
GND
Figure 3: Connecting DC-DC Converters in Series
A-4
2014
www.recom-international.com
DC-DC Converter Applications
Connecting
DC-DC Converters in Parallel
Example 1:100W DC/DC Power Supply
Connecting the outputs of DC/DC converters in
parallel is possible but not recommended.
Usually DC/DC converters have no possibility
to balance out the output currents.
DC/DC
Converter 1
RPP50-2405S
Si7495DP
+Vout
-Vout
E1
So there is potential danger that if the loading
is asymmetrical, that one of the converters
starts to be overloaded while the others have to
deliver less current. The
over-loaded
converter may then drop out of circuit leading
to power supply oscillation.
V1
5V @ 20A
G1
Load Share
Controller Vs
LTC4416
E2
GND
G2
V2
+Vout
DC/DC
Converter 2
RPP50-2405S
The only possibility to balance out the
individual currents is to use a converter with a
special load balance function (like the R-5xxx
series- see Figure 4) or to use the converters
with an external load-share controller.
Si7495DP
-Vout
Example 2: 3.3V @8A POL Power Supply
Vcc
DC
+V
+Vin
DC
Balance
Link
+
100µF
GND
E1
+
DC
DC
Si7495DP
+Vout
DC/DC
Converter 1
R-743.3P
V1
3.3V @ 8A
G1
Load Share
Controller Vs
LTC4416
E2
GND
3.3µF
0V
G2
V2
GND
+Vin
Figure 4: Paralleled DC-DC Converters with Balance
Function.
LOAD SHARE CONTROLLER
Refer to figure 5 for some application examples using the LTC4416 Dual PowerPath controller and two external FETs. The load share
controller IC can balance out the load currents
as long as the outputs are within 500mV of
each other.
If two or more converters are operated from a
common supply voltage (inputs in parallel),
then input decoupling via LC-filters is
recommended. This helps to avoid hard-tohandle conducted EMI caused by the
non-synchronized oscillators. Also inrush
current peaks are lowered. Having several
smaller filters, one for each converter, is recommended instead of using one common filter for all converters, as this helps to reduce
the possibility of the converters beating against
each other.
Chaining
DC-DC Converters
Connecting the output of one DC/DC converter
to the input of a second converter is sometimes a very useful technique. For example, the
benefits of the very wide input voltage range
of the innoline series can be combined with the
high isolation of the econoline series to create
a combination converter which is both isolated
www.recom-international.com
3.3µF
+
DC/DC
Converter 2
R-743.3P
+Vout
+
Si7495DP
100µF
GND
Figure 5: Doubling Output Power via Paralleled DC-DC Converters and a Load Share Controller
and with an exceptionally wide 7:1 input
voltage range.
Vcc = 5V
DC
Similarly, an isolated DC/DC converter can be
used to power a R-78 switchning regulator to
provide dual positive outputs with nonstandard voltages.
In every case, some care has to be taken
concerning the inrush current of the second
converter in the chain. If the peak inrush
current is too high, then then the first
converter in the chain may not start up.
The solution to this problem is to add some
capacitance to supply the peak inrush current
and/or to delay the start-up of the second
converter in the chain.
Figure 5a shows some typical examples.
2014
+12V
REC5-0512SRW/H6/A
DC
+Vo
-Vo
10µ
R-783.3
-0.5
0V
GND
+15V
Vcc = 9-39V
RP15-2415SAW
DC
DC
GND
+3.3V
RP08-1205DA
+Vo
C1
-Vo
DC
CTRL
DC
+5V
0V
-5V
RP08 starts up after delay
C1 provides inrush start up current
Figure 5a: Chained DC-DC Converter Examples
A-5
DC-DC Converter Applications
Filtering
When reducing the ripple from the converter,
at either the input or the output, there are
several aspects to be considered. Recom
recommend filtering using simple passive LC
networks at both input and output (see figure
6). A passive RC network could be used,
however, the power loss through a resistor is
often too high.The self-resonant frequency of
the inductor needs to be significantly higher
than the characteristic frequency of the
device (typically 1OOkHz for Recom DC-DC
converters). The DC current rating of the
inductor also needs consideration, a rating of
approximately twice the supply current is
recommended.
The DC resistance of the inductor is the final
consideration that will give an indication of
the DC power loss to be expected from the
inductor.
Output Filtering calculation:
Calculating of the filtering components can be
done using
This frequency should be significant lower than
the switching frequency of the converter.
Example - RC series:
Operating frequency = 85kHz max.
then, fc =10 % of 85 kHz = 8,5 kHz
LIN
DC
VIN
CIN
DC
GND
When choosing a value for the filtering capacitor
please take care that the maximum capacitive
load is within the specifications of the converter.
A-6
CO
CO
LOUT
+VOUT
0V
-VOUT
Figure 6: Input and Output Filtering
Common Mode Chokes
Better results in filtering can be achieved if
common mode chokes are used instead of a
single choke.
Common mode chokes are multiple chokes
sharing a core material so the common mode
rejection (Electrical noise which comes through
one power line and returns to the noise source
through some type of ground path is common
mode noise.) is higher.
Please refer to our page "Common Mode
Chokes for EMC" also part of these application
notes. These can be used for input filtering as
well as for the output side.
Limiting Inrush Current
Using a series inductor at the input will limit
the current that can be seen at switch on
(see figure 7).
If we consider the circuit without the series
inductor, then the input current is given by;
Figure 7: Input Current & Voltage at Switch On
However, depending on your application design
and loadsituation may interfer with the
calculated filter so testing in the final
application and re-adjustment of the
component’s values may be necessary.
LOUT
( )
i = V exp – t
R
RC
When the component is initially switched on
(i.e. t=O) this simplifies to;
i=V
R
2014
This would imply that for a 5V input, with say
50mOhm track and wire resistance, the inrush
current could be as large as 1OOA. This could
cause a problem for the DC-DC converter.
A series input inductor therefore not only filters
the noise from the internal switching circuit,
but also limits the inrush current at switch on.
A typical value for an input inductor used to
reduce the inrush current is 1mH or higher.
A typical value for an inductor used to filter the
input is 50-300µH. So although the circuit
diagram may look similar, the input inductors
have very different functions and different
values.
If a common mode choke is used as an inrush
current limiter, it has the added advantage over
a single inductor that the inrush currents flowing
in the two windings cancel out and the ferrite is
less likely to go into saturation.
Short Circuit Protection in
0.25W - 2W Econoline converters
In the low wattage, unregulated converter Portfolio we offer continuous short circuit protection (option /P). Especially in applications where
the output of converters is connected via a plug
and socket to an external module, the chances
of having a short circuit across the output is
quite high. A conventional unregulated converter can withstand a short circuit across the outputs for only a limited time. The same condition
can occur with high capacitive loads if they have
a low ESR.
RECOM uses balancing between transformer
core saturation ratings and the maximum electrical ratings of the switching transistors in the
primary side oscillator to create a converter that
can withstand a continuous short circuit
(<1 Ohm) across the outputs without failing.
However, this is NOT an overload protection.
If the coverters are over-loaded but not short
circuited, the converters may still overheat and
fail.
www.recom-international.com
DC-DC Converter Applications
Maximum Output Capacitance
A simple method of reducing the output ripple
is simply to add a large external capacitor. This
can be a low cost alternative to the LC filter
approach, although not as effective. There is,
however, also the possibility of causing start
up problems, if the output capacitance is too
large.
Recom uses the following definition for maximum capacitive load: “the maximum output
capacitance that permits start-up in less than
one second and does not damage the converter”
With a large output capacitance at switch on,
there is no charge on the capacitors and the
DC-DC converter immediately experiences a
large current demand at its output. The inrush
current can be so large as to exceed the
ability of the DC-DC converter, and the device
can go into current limit.
For converters with a constant power limit,
the effect of a large capacitive load is to
make the output voltage slowly ramp up
over time. However, for converters with a
hiccup protected output, the device could
continuously oscillate as it tries to start, goes
into overload shutdown and then retries again.
The DC-DC converter may not survive if this
condition persists.
For unregulated converters, the overload
condition caused by the capacitor charging
current could damage the converter. If
instead of single capacitors on outputs an
RC-filter or LC-Filter is used, the maximum
capacitive load can be higher because the
resistor/choke reduces the capacitor inrush
current peak. However, fairly large resistors or
inductances are required to have a meaningful
effect.
be calculated.
Settling Time
The general isolation impedance equation for a
given frequency (f) is given by:
The main reason for not fitting a series
inductor internally, apart from size constraints,
is that many applications require a fast switch
on time. When the input voltage is a fast ramp,
then the output can respond within 500µs of
the input reaching its target voltage (measured
on a range of RA/RB and RC/RD converters
under full output load without external filters).
The use of external filters and additional input
or output capacitance will slow this reaction
time. It is therefore left to the designer to
decide on the predominant factors important
for their circuit: settling time or noise
performance.
Isolation Capacitance
and Leakage Current
The isolation barrier within the DC-DC
converter has a capacitance, which is a
measure of the coupling between input and
output circuits. Providing this is the largest
coupling source, a calculation of the leakage
current between input and output circuits can
Assuming we have a known isolation capacitance (Cis - refer to datasheet) and a known
frequency for either the noise or test signal,
then the expected leakage current (iL) between
input and output circuits can be calculated
from the impedance.
Zf = ___1___
j 2 π C is
For an RB-0505D, the isolation capacitance is
18pF, hence the isolation impedance to a 50Hz
test signal is:
Z50 = ___1_______ = 177 M Ω
j 2 π 50 18 pf
If using a test voltage of 1kVrms, the leakage
current is:
iL = Vtest = _1000V_ = 5.65 µA
177 M Ω
Zf
It can be easily observed from these simple
equations that the higher the test or noise
voltage, the larger the leakage current, also the
lower the isolation capacitance, the lower the
leakage current. Hence for low leakage
current, high noise immunity designs, high
isolation DC-DC converters should be selected
with an appropriate low isolation capacitance.
RECOM converters with Power Limiting
Overload Protection
RECOM converters with Hiccup Overload
Protection
RY-P, R1Z, R0.25Z, RSO, RS, RW2, RS3,
RW-S, RW-D, REC3, REC3.5, REC5, REC6,
REC7.5, REC8, REC10, REC15, Rxx-B,
RP08, RP12, RAC05-A, RAC05-B,
RAC10-A, RAC10-B, RAC15-A, RAC15-B,
RAC20-A, RAC20-B, RAC30-A, RAC40-A,
RAC40-B
RP10-E, RP12-SOF, RP15-A, RP15-F,
RP20-A, RP20-F, RP30-E, RP30-F, RP40-G,
RP60-G, RAC03-A, RAC04-A, RAC06-C,
RAC60-B
RECOM converters with Power Limiting
Overload Protection, but need diode
protection with high capacitive loads
RECOM converters with Hiccup Overload
Protection, but can cope well with high
capacitive loads
R-78xx, R-78Bxx, R-78HBxx, R-5xxx,
R-6xxx, R-7xxx
RPP20, RPP30, RPP40, RPP40, RPP50
www.recom-international.com
2014
A-7
DC-DC Converter Applications
Application Examples
Overload Protection
Although the use of filtering will prevent
excessive current at power-on under normal
operating conditions, many of the lower cost
converters have no protection against an output
circuit taking excessive power or even going
short-circuit. When this happens, the DC-DC
converter will take a large input current to try
to supply the output. Eventually the converter
will overheat and destroy itself if this condition
is not rectified (short circuit overload duration
is only for 1s on a standard unregulated part).
There are several ways to prevent overload at
the outputs destroying the DC-DC converter.
The simplest being a straight forward fuse.
Sufficient tolerance for inrush current is required
to ensure the fuse does not blow on power-on
(see figure 8). Another simple scheme that
can be applied is a circuit breaker.
There is also the potential to add some
intelligence to the overload scheme by either
detecting the input current, or the output
voltage (see figure 9).
If there is an intelligent power management
system at the input, using a series resistor (in
place of the series inductor) and detecting the
voltage drop across the device to signal the
management system can be used.
A similar scheme can be used at the output to
determine the output voltage, however, if the
management system is on the input side, the
signal will need to be isolated from the
controller to preserve the system isolation
barrier (see figure 10).
There are several other current limiting techniques that can be used to detect an overload
situation, the suitability of these is left to the
designer. The most important thing to consider
is how this information will be used. If the
system needs to signal to a controller the
location or module causing the overload, some
form of intelligence will be needed. If the device
simply needs to switch off, a simple fuse type
arrangement will be adequate.
Unregulated RECOM DC/DC converters usually
are short circuit protected only for a short time,
e.g. 1 second.
VIN
By option they can be continous short circuit
protected (option /P), then their design is able
to withstand the high output current in a short
circuit situation without any need for extra circuit protection.
All Recom DC-DC converters which include
an internal linear regulator have a thermal
overload shut-down condition which protects
these devices from excessive over-load.
If this condition is to be used to signal a power
management system, the most suitable
arrangement is the output voltage detector
(see figure 10a), since this will fall to near zero
on shut-down. Wide input range regulated
converters offer overload protection / short
circuit protection via an internal circuit that
interfers with the primary oscillator so the
switching is regulated back in situations of
overload or output short circuit.
FUSE
DC
CIN
DC
GND
Figure 8: Simple Overload Protection
Rin
Vcc
DC
DC
Vout
GND
a) Series Resistor for Input Current Measurement
Ilimit
Vcc
DC
R1
DC
Rgnd
R2
GND
b) Ground Current Monitor
Choose current limit (ILIMIT)
and ground resistor (RGND) so
that : 0.7V = RGND x ILIMIT.
Figure 9: Input Monitored Overload Protection
A-8
2014
www.recom-international.com
DC-DC Converter Applications
Input Voltage
Drop-Out (brown-outs)
When the input voltage drops, or is momentarily
removed, the output circuit would suffer similar
voltage drops. For short period input voltage
drops, such as when other connected circuits
have an instantaneous current demand, or
devices are plugged in or removed from the
supply rail while 'hot', a simple diode-capacitor
arrangement can prevent the output circuit
from being effected.
Opto-Isolated Power Good / Overload Detector
(On overload +VO falls and the LED switches off, the VOL. line is then pulled high.)
Figure 10 : Ouput Monitored Overload Protection
LIN
ZDX60
DC
VIN
Output Circuit
47pf
DC
GND
The circuit uses a diode feed to a large reservoir
capacitor (typically 47µF electrolytic), which
provides a short term reserve current source
for the converter, the diode blocking other
circuits from draining the capacitor over the
supply rail. When combined with an in-line
inductor this can also be used to give very
good filtering. The diode volt drop needs to be
considered in the power supply line under
normal supply conditions. A low drop Schottky
diode is recommended (see figure 11).
No Load Over Voltage Lock-Out
Unregulated DC-DC converters are expected to
be under a minimum of 10% load, hence
below this load level the output voltage is
undefined. In certain circuits this could be a
potential problem.
Figure 11 : Input Voltage Drop-out
The easiest way to ensure the output voltage
remains within a specified tolerance, is to add
external resistors, so that there is always a
minimum 10% loading on the device (see
figure 12). This is rather inefficient in that 10%
of the power is always being taken by this load,
hence only 90% is available to the additional
circuitry.
Zener diodes on the output are another simple
method. It is recommended that these be used
with a series resistor or inductor, as when the
Zener action occurs, a large current surge may
induce signal noise into the system.
Figure 12: No Load over Voltage Lock-Out
Long Distance Supply Lines
RB-0512D
RO-2405
DC
Vin
GND
Cable
DC
DC
DC
Target Circuit
When the supply is transmitted via a cable,
there are several reasons why using an isolated
DC-DC converter is good design practice (see
figure 13). The noise pick up and EMC
susceptibility of a cable is high compared to a
pcb track. By isolating the cable via a DC-DC
converter at either end, any cable pick-up will
appear as common mode noise and should be
self-cancelling at the converters.
Figure 13: Long Distance Power Transfer
www.recom-international.com
2014
A-9
DC-DC Converter Applications
Another reason to use converter pairs is to
reduce the cable power loss is by using a high
voltage, low current power transfer through the
cable and reconverting at the terminating
circuit. This will also reduce noise and EMC
susceptibility, since the noise voltage required
to affect the rail is also raised.
For example, compare a system having a 5V
supply and requiring a 5V, 500mW output at a
remote circuit. Assume the connecting cable
has a 100 Ohm resistance. Using an RO-0505
to convert the power at either end of the cable,
with a 100mA current, the cable will lose 1W
(I2R) of power. The RO would not be suitable,
since this is its total power delivery; hence
there is no power available for the terminating
circuit. Using a RB-0512D to generate 24V and
a RO-2405S to regenerate the 5V, only a 21
mA supply is required through the cable, a
cable loss of only 44mW.
Some high power, low output voltage circuits
experience significant voltage drops even along
the short tracks on a circuit board. The
Powerline RP40 and RP60 and the Innoline
R-5xxxA converters feature a sense
connection which can automatically
compensate for voltage losses in a circuit (see
Figure 13a). The sense inputs are used by the
internal regulator in the converters so that the
set output voltage is measured at the load
rather than on the output pins of the converter.
RP60-xxxxS
DC
DC
Pre- and Post Regulation
The usefulness of many DC-DC converters can
be enhanced by pre- or post-regulation.
The usual input voltage range of a DC-DC
converter is either fixed, 2:1 or 4:1 depending
on the converter technology used inside the
device. Switching regulators have typically a
much wider input voltage range - up to 8:1,
but do not have the advantage of the DC-DC
converter’s galvanic isolation. By combining
the two techniques and using a switching
regulator as a pre-regulator, an ultra-wide
range, isolated DC-DC converter supply can be
built (see Figure 15a)
Vcc = 9~72VDC
R-78HB05-0.5
LCD Display Bias
DC
-24V
Load
-Sense
-Vo
Post regulation is useful to combine the
advantages of a linear regulator’s low noise
output with the ability of a DC-DC converter to
boost a lower input voltage to a higher output
voltage.
Vcc = 5V
RB-053.3D
DC
DC
GND
+6.6V
+Vo
7805
LDO
+5V
100n
2µ2
-Vo
(Optional Link)
<5µV
Low Noise
Regulated
5V Output
0V
Figure 15b: Post-Regulation Example
RI-0505S
DC
+5V @ 400mA
Isolated Vout
In this example, a low cost RB unregulated
converter is used to boost a 5V supply up to
6.6V so that a low drop out linear regulator can
produce a low noise, regulated 5V output.
EIA-232 Interface
GND
Figure 15a: Pre-Regulation Example
RO-0524S
DC
+Sense
Figure 13a: Using Sense Inputs to Compensate for Voltage Drops in the Connections to the Load
DC
A LCD display typically requires a positive or
negative 24V supply to bias the crystal. The
RO-0524S converter was designed specifically
for this application. Having an isolated OV output, this device can be configured as a +24V
supply by connecting this to the GND input, or
a –24V supply by connecting the +Vo output to
GND (see figure 14).
+Vo
Liquid
Crystal
Display
In a mains powered PC often several supply
rails are available to power a RS232 interface.
However, battery operated PC’s or remote
equipment having a RS232 interface added
later, or as an option, may not have the supply
rails to power a RS232 interface. Using a
RB-0512S is a simple single chip solution,
allowing a fully EIA-232 compatible interface
to be implemented from a single 5V supply rail,
and only two additional components (see figure
16a).
(up to 42mA)
Figure 14: LCD Display Bias
A-10
2014
www.recom-international.com
DC-DC Converter Applications
3V/5V Logic Mixed Supply Rails
+12V
EIA-232 Port
VCC
5V
VDD
DCD
RB-0512D
DB9S Connector
DSR
+VO
RX
DC
OV
RTS
TX
-VO
CTS
DC
DTR
GND
RI
There is now another option, mixed logic
functions running from separate supply rails. A
single 3.3V line can be combined with a range
of DC-DC converters from Recom, to generate
voltage levels to run virtually any standard logic
or interface IC.
SN75C185
The Recom range includes dual output parts
for powering analogue bipolar and amplifier
functions (RB series), as well a single output
function for localised logic functions (RM, RN or
RNM series). A typical example might be a
RS232 interface circuit in a laptop PC using a
3.3V interface chip (such as the LT1330),
which accepts 3.3V logic signals but requires
a 5V supply (see figure 16b). Recom has another
variation on this theme and has developed two
5V to 3.3V step down DC-DC converters
(RNM-053.3S and R0-053.3S). These have
been designed to allow existing systems to
start incorporating available 3.3V l.C.’s
without having to redesign their power
supply.
Figure 16a: Optimised RS232 Interface
3.3VCC
RNM-3.305S
3
1
8
DC
DC
+5V
7
OV
GND
GND
VCC
1µF
1
3.3V
100nF
-V
+V
2
28
3
26
4
27
TX1
14
25
5
TX1
RX1
24
6
RX1
+
This is particularly important when trying to
reduce the overall power demand of a system,
but not having available all of the functions at
the 3.3V supply.
+
220nF
3.3V Logic
There has been a lot of attention given to new
l.C.'s and logic functions operating at what is
rapidly emerging as the standard supply level
for notebook and palmtop computers. The 3.3V
supply is also gaining rapid acceptance as the
defacto
standard
for
personal
telecommunications, however, not all circuit
functions required are currently available in a
3.3V powered IC. The system designer
therefore has previously had only two options
available; use standard 5V logic or wait until
the required parts are available in a 3.3V form,
neither being entirely satisfactory and the
latter possibly resulting in lost market share.
200nF
RS232
The main application for this range of devices
are system designers, who want to provide
some functionality that requires a higher
voltage than is available from the supply rail, or
for a single localised function. Using a fully
isolated supply is particularly useful in interface
functions and systems maintaining separate
analogue and digital ground lines.
17
LT1330
GND
Figure 16b: RS232 Interface with 3V Logic
www.recom-international.com
2014
A-11
DC-DC Converter Applications
Isolated Data Acquisition System
Any active system requiring isolation will need a DC-DC converter to provide the power transfer for the isolated circuit. In a data acquisition circuit
there is also the need for low noise on the supply line; hence good filtering is required. The circuit shown (see figure 17) provides a very high
voltage isolation barrier by using an RH converter to provide the power isolation and opto isolators for the data isolation. An overall system isolation
of 2.5kV is achieved.
EMC Considerations: When used for isolating a local power supply and incorporating the appropriate filter circuits as illustrated in Fig. 17), DC-DC
converters can present simple elegant solutions to many EMC power supply problems. The range of fixed frequency DC-DC converters is
particularly suitable for use in EMC problem situations, as the stable fixed switching frequency gives easily characterised and easily filtered output.
The following notes give suggestions to avoid common EMC problems in power supply circuits.
5V
4K7
Data
Opto Isolators
RH-0505
1K2
5V
5V Logic Circuit
Data
CS
4K7
5V
CS
1K2
4K7
Status
VCC
+5V
1K2
ZN509
CLK
+5V
CLK
Vref
Status
47µH
+5V
AIN
1K2
DC
DC
+5V
1µF
470vF
GND
4K7
1K2
SFH610
Figure 17: Isolated Serial ADC System
Power Supply Considerations
VCC
PSU
CCT1
● Eliminate loops in supply lines (see figure 18).
● Decouple supply lines at local boundaries (use LC filters with low Q,
8
CCT2
see figure 19).
● Place high speed sections close to the power line input, slow
speed sections furthest away (reduces power plane transients, see
figure 20).
● Isolate individual systems where possible (especially analogue
and digital systems) on both power supply and signal lines (see figure 21).
An isolated DC-DC converter can provide a significant benefit to help
reduce susceptibility and conducted emission due to the isolation of
both power rail and ground from the system supply. Recom primarily
uses toroidal transformers in our DC-DC converters and as such they
have negligible radiated EMI, but all DC-DC converters are switching
devices and as such will have a characteristic switching frequency,
which may need some additional filtering.
GND
VCC
PSU
CCT1
3
CCT2
GND
Interpretation of DC-DC Converter EMC Data
Figure 18: Eliminate Loops in Supply Line
Electromagnetic compatibility (EMC) of electrical and electronic products
is a measure of electrical pollution. Throughout the world there are
increasing statutory and regulatory requirements to demonstrate the
EMC of end products. In Europe the EC directive 89/336/EEC requires
that any product sold after 1 January 1996 complies with a series of
EMC limits, otherwise the product will be prohibited from sale within
the EEC and the seller could be prosecuted and fined.
Although DC-DC converters are generally exempt from EMC restrictions
on the grounds that they are components, it is the belief of Recom that
information on the EMC of these components can help designers plan
ahead so that their end products can meet the relevant statutory EMC
requirements. It must be remembered however, that a DC-DC converter
is unlikely to be the only com-ponent in the power supply chain, hence
the information quoted needs interpretation by the circuit designer to
determine its impact on the final EMC performance of their system.
VCC
CCT1
CCT2
GND
Figure 19: Decouple Supply Lines at Local Boundaries
A-12
2014
www.recom-international.com
DC-DC Converter Applications
Hence, the EC directive covers the frequency
spectrum 150kHz to 1GHz, but as two
separate and distinct modes of transmission.
Local
P
S
U
Power Input
High Speed
Circuit
DC Circuit
The Recom range of DC-DC converters feature
toroidal transformers. These have been tested
and proved to have negligible radiated noise.
The low radiated noise is primarily due to
toroidal shaped transformers maintaining the
magnetic flux within the core, hence no
magnetic flux is radiated by design. Due to the
exceptionally low value of radiated emission,
only conducted emissions are quoted.
CCT2
Conducted emissions are measured on the
input DC supply line. Unfortunately no
standards exist for DC supplies, as most
standards cover mains connected equipment.
This poses two problems for a DC supplied
device, firstly no standard limits can be directly
applied, since the DC supplied device does
not directly connect to the mains, also all
reference material uses the earth-ground as
a reference point. In a DC system often the OV
is the reference, however, for EMC purposes, it
is probably more effective to maintain the earth
as the reference, since this is likely to be the
reference that the shielding is connected to.
Consequently all measurements quoted are
referenced to the mains borne earth.
Low Speed
Circuit
Medium Speed
Circuit
Filter
Figure 20: Place High Spead Circuit Close to PSU
VCC
DC
DC
CCT1
DC
DC
GND
Figure 21 : Isolate Individual Systems
Line Impedance Stabilisation
Network (LISN)
Power Supply
50Ω
Termination
–
LISN
DC
Load
DC
+
LISN
To Spectrum Analyser
Figure 22: Filtered Supply to DC-DC Converter
The notes given here are aimed at helping
the designer interpret the effect the DC-DC
converter will have on the EMC of their end
product, by describing the methods and rationale for the measurements made. Where
possible CISPR and EN standards have been
used to determine the noise spectra of the
components, however, all of the standards
reference to mains powered equipment and
interpretation of these specifications is
necessary to examine DC supplied devices.
www.recom-international.com
Conducted and
Radiated Emissions
There are basically two types of emissions
covered by the EC directive on EMC: radiated
and conducted. Conducted emissions are
those transmitted over wire connecting circuits
together and covers the frequency spectrum
150kHz to 30MHz. Radiated are those emissions
transmitted via electromagnetic waves in air
and cover the frequency spectrum 30MHz to
1GHz.
2014
It is necessary to ensure that any
measure-ment of noise is from the device
under test (DUT) and not from the supply to this
device. In mains connected circuits this is
important and the mains has to be filtered prior
to supply to the DUT. The same approach has
been used in the testing of DC-DC converters
and the DC supply to the converter was filtered,
to ensure that no noise from the PSU as
present at the measuring instrument.
A line impedance stabilisation network (LISN)
conforming to CISPR 16 specification is
connected to both positive and negative supply
rails and referenced to mains earth (see figure
22). The measurements are all taken from the
positive supply rail, with the negative rail
measurement point terminated with 50 Ohm to
impedance match the measurement channels.
A-13
DC-DC Converter Applications
2
100
Conducted Emission (dBuV)
these arise from the fundamental switching
frequency and its harmonics (odd line spectra)
and the full rectified spectra, at twice the
fundamental switching frequency (even line
spectra). Quasi-resonant converters, such as
the Recom range, have square wave switching
waveforms, this produces lower ripple and a
higher efficiency than soft switching devices,
but has the drawback of having a relatively
large spectrum of harmonics.
4
1
80
8
6
12
10
3
60
5
7
9
11
13
40
20
0
0
100
300
200
400
500
Frequency (kHz)
Figure 23: Individual Line Spectra
50
40
Frequency (kHz)
30
20
10
0
0
2
4
6
8
10
12
14
Input Voltage (V)
Figure 24: Frequency Voltage Dependency
The EC regulations for conducted interference
covers the bandwidth 150kHz to 30MHz.
Considering a converter with a 100kHz nominal
switching frequency, this would exhibit 299
individual line spectra. There will also be a
variation of absolute switching frequency with
production variation, hence a part with a 90kHz
nominal frequency would have an additional
33 lines over the entire 30MHz bandwidth.
Absolute input voltage also produces slight
variation of switching frequency (see figure
24). Hence, to give a general level of
conducted noise, we have used a 100kHz
resolution bandwidth (RBW) to examine the
spectra in the data sheets. This wide RBW
gives a maximum level over all the peaks,
rather than the individual line spectra. This is
easier to read as well as automatically
compensating for variances in switching
frequency due to production variation or
differences in absolute input voltage (see
figure 25).
Conducted Emission (dBuV)
100
The conducted emissions are measured under
full load conditions in all cases. Under lower
loads the emission levels do fall, hence full load
is the worst case condition for conducted line
noise.
80
60
40
20
0
100kHz
1MHz
10MHz
100MHz
Frequency
Econoline converters will meet the
requirements for FCC / EN55022 Class A and
Class B limits for conducted and radiated
emissions with the addition of an external filter.
Figure 25 : V Spectrum
Shielding
At all times the DUT, LlSN’s and all cables
connecting any measurement equipment,
loads and supply lines are shielded. The
shielding is to prevent possible pick-up on
cables and DUT from external EMC sources
(e.g. other equipment close by). The shielding
is referenced to mains earth (see figure 22).
Line Spectra of DC-DC Converters
All DC-DC converters are switching devices,
A-14
Econoline Filters for Conducted
and Radiated Emissions
hence, will have a frequency spectra.
Fixed input DC-DC converters have fixed
switching frequency, for example the RC/RD
range of converters has a typical switching
frequency of 50kHz. This gives a stable and
predictable noise spectrum regardless of load
conditions.
The following filter circuit suggestions are
based on EMC tests carried out in an EMC test
facility on single converters. Different
component values or filter configurations may
be required if several converters share a
common supply, if different types of converter
are used together or if the supply voltage or
load is not placed close to the converters.
If we examine the noise spectrum closely (see
figure 23) we can see several distinct peaks,
2014
www.recom-international.com
DC-DC Converter Applications
Econoline EMC Filter Suggestions: Low Power Regulated and Unregulated Converters
For R1S, R2S: see Datasheet
EN55022 Class A
(Omit C1, L1 and C3)
RM, RSS, RSD, RNM,ROM,
RO, RBM,RB,RE.RK, RH, RN,
RTS, RTD, RI, RD, RKZ,RJZ,
RZ, RSZ, RY
C2=3.3µF
L1
Input
+
+
C1
C2
Output
RP, RxxPxx, RU, RxxP2xx,
RUZ, RV
C2=10µF
C3
EN55022 Class B
EN55022 Class A
EN55022 Class B
RM, RSS, RSD, RNM,ROM, RO,
RBM,RB,RE.RK, RH, RN, RTS, RTD,
RI, RD, RKZ,RJZ, RZ, RSZ, RY
C1=10µF, L1 = 470µH, C2=4.7µF,
C3 = 2.2nF
(omit C3)
RS0, RS, RW2
RS3, RW-S, RW-D, REC3-R
C1=10µF, L1 = 1mH, C2=20µF,
C3 = 2.2nF
RS0, RS, RW2
RS3, RW-S, RW-D, REC3-R
C1=10µF, L1 = 1mH, C2=10µF
All capacitors are MLCC
RP, RxxPxx, RU, RxxP2xx, RUZ, RV
C1=10µF, L1 = 470µH, C2=10µF,
C3 = 2.2nF
Recommended Inductors:
WE 7447471471 470µH
WE 7447471102 1000µH or
WE 7687709102 1000µH
Econoline EMC Filter Suggestion: 3W - 15W Regulated Converters
EN55022 Class B
2:1 and 4:1 REC3-REC08
Converters:
CMC= 7448640395 820µH
Input
+
+
C1
C2
CMC
2:1 and 4:1 REC10-REC15
Converters:
CMC= 7446723001 1200µH
C3=C4=3.3nF
2:1 and 4:1 REC3-REC7.5
C1=10µF, C2=15µF,
C3=2.2nF
REC08-05xx:
C1= C2 = 22µF
REC08/10/15-12xx:
C1=C2=10µF
REC08/10/15-24xx:
C1=C2=4.7µF
REC08/10/15-48xx:
C1=C2 =2.2µF
C3
Input
+
+
C1
C2
www.recom-international.com
Dual
Output
CMC
C3
"A" Pinning
Single Output
C1
For details of common mode
chokes refer to Powerline
application notes section
Single
Output
C3
4
3
1
2
C2
Ground
Plane
Bottom View
CMC
2014
A-15
DC-DC Converter Applications
Figure 26: Typical Switching Frequency vs. Temperature
Temperature Performance
Surface Mount DC-DC Converters
The temperature performance of the DC-DC
converters detailed in this book is always better
than the quoted operating temperature range.
The main reason for being conservative on the
operating temperature range is the difficulty of
accurately specifying parametric performance
outside this temperature range.
Production Guideline Application Note
The introduction by Recom of a new and
innovative method of encapsulating hybrid DCDC converters in a transfer moulded (TM)
epoxy molding compound plastic has enabled
a new range of surface mount (SMD) DC-DC
converters to be brought to market, which
addresses the component placement with
SOIC style handling.
There are some limiting factors which provide
physical barriers to performance, such as the
Curie temperature of the core material used in
the DC-DC converter (the lowest Curie
temperature material in use at Recom is
125°C). Ceramic capacitors are used almost
exclusively in the DC-DC converters because
of their high reliability and extended life
properties, however, the absolute capacity of
these can fall when the temperature rises
above 85°C (i.e. the ripple will increase). Other
considerations are the power dissipation within
the active switching components, although
these have a very high temperature rating.
Their current carrying capacity derates as
temperature exceeds 100°C.
Therefore this allows the DC-DC converters
to be used above their specified operating
temperature, providing the derating of power
delivery given in the specification is adhered
to. Components operating outside the quoted
operating temperature range cannot be
expected to exhibit the same parametric
performance that is quoted in the specification.
An indication of the stability of a device can be
obtained from the change in its operating
frequency, as the temperature is varied (see
figure 26). A typical value for the frequency
variation with temperature is 0.5% per °C, a
very low value compared to other commercial
parts. This illustrates the ease of filtering of
Recom DC-DC converters, since the frequency
is so stable across load and temperature ranges.
A-16
With any new component there are of course
new lessons to be learned with the mounting
technology. With the Recom SMD DC-DC
converters, the lessons are not new as such,
but may require different production
techniques in certain applications.
Component Materials
Recom SMD converters are manufactured in a
slightly different way than the through-hole
converters. Instead of potting the PCB board
inside a plastic case with conventional epoxy
the whole package is molded around the PCB
board with epoxy molding compound plastic.
Open frame SMD parts have no moulding
compound and the case (when fitted) is
provided purely to allow the pick-amd-place
machine to be able to grip the part and to
provide a surface for the part number and
datecode. As the parts are nor encapsulated,
they have more freedom to expand and
contract which makes them ideal for vapour
phase reflow processes and allows greater
flexibility in the termperature profile.
All materials used in RECOM lead-free products
are ROHS compliant, thus the total amount
of the restricted materials (lead, mercury,
cadmium, hexavalent chromium, PBBs and
PBDEs) are below the prescribed limits.
Detailed chemical analysis reports are available.
2014
Component Placement
Recom SMD DC-DC converters are designed
to be handled by placement machines in a
similar way to standard SOIC packages. The
parts are available either in tubes (sticks) or in
reels. The parts can therefore be placed using
machines with either vibrational shuttle, gravity
feeders, or reel feeders.The vacuum nozzle for
picking and placing the components can be the
same as used for a standard 14 pin or 18 pin
SOIC (typically a 5 mm diameter nozzle). An
increase in vacuum pressure may be
beneficial, due to the heavier weight of the
hybrid compared to a standard SOIC part (a
typical 14 pin SOIC weighs 0.1g, the Recom
12.00
8
5
1 2
4
1.20
Top View
1.80
SMD DC-DC converter weighs 1.5 ~ 2,7g).
It is advisable to consult your machine supplier
on the best choice of vacuum nozzle if in doubt.
If placing these components by hand, handle
the components only by the central body area
where there are no component pins.
Component Alignment
The components can be aligned by either
optical recognition or manual alignment. If
using manual alignment it should be ensured
that the tweezers press on the component
body and not on the pins. The components
themselves are symmetrical along their axis,
hence relatively easy to align using either
method.
Solder Pad Design
The Recom SMD DC-DC converters are
designed on a pin pitch of 2,54mm (0.1") with
1,20 mm pad widths and 1,80 mm pad
lengths.
This allows pads from one part to be used
within a PCB CAD package for forming the pad
layouts for other SMD converters. These pads
are wider than many standard SOIC pad sizes
(0.64mm) and CAD packages may not
accommodate these pins with a standard SOIC
pad pattern. It should be remembered that
these components are power supply devices
and as such need broader pads and thicker
component leads to minimise resistive losses
within the interconnects.
www.recom-international.com
DC-DC Converter Applications
The adhesive prevents the SMD parts being
”washed off“ in a wave solder, and being
”vibrated off“ due to handling on a double
sided SMD board.
Lead-free Recommended Soldering Profile (SMD parts)
300
10-30s
min. 300s
Temperature (°C)
250
(245°C)
200
150
Pre - Heat
100
50
50
100
200
150
250
300
350
400
450
500
Time (seconds)
Lead-free Recommended Soldering Profile (Through hole parts)
Double Wave
340
320
300
3 - 5 seconds
Temperature (°C)
280
260
240
220
Forced Cooling
60°C/s Min.
100°C ~ 150°C Max.
200
180
160
140
120
100
80
60
40
20
0
Natural Cooling
Enter Wave
Pre - Heat
0
10
20
30
40
50
60
70
80
Time (seconds)
90
100
110
120
Notes: 1. The wave solder profile is measured on lead temperature.
2. Need to keep the solder parts internal temperature less than about 210°C
Solder Reflow Profile
RECOM’s SMD converters are designed to
withstand a maximum reflow temperature of
245°C (for max. 30seconds) in accordance
with JEDEC STD-020C. If multiple reflow
profiles are to be used (i.e. the part is to
passthrough several reflow ovens), it is
recommended that lower ramp rates be used
than the maximum specified in JEDEC STD020C. Continual thermal cycling to this
profile could cause material fatigue, if more
than 3 maximum ramp cycles are used.
In general these parts will exceed the re-flow
capability of most IC and passive components
on a PCB and should prove the most thermally
insensitive component to the reflow conditions
www.recom-international.com
Recommended Solder Reflow Profile:
The following 2 graphs show the typical
recommended solder reflow profiles for SMD
and through-hole ROHS compliant converters.
The exact values of the profile’s peak and its
maximum allowed duration is also given in the
datasheet of each converter.
Adhesive Requirements
If SM surface mount components are going to
be wave soldered (i.e. in a mixed through hole
and SMD PCB) or are to be mounted on both
sides of a PCB, then it is necessary to use an
adhesive to fix them to the board prior to
reflow.
2014
As mentioned previously, the Recom range of
SMD DC-DC converters are heavier than
standard SOIC devices. The heavier weight is a
due to their size (volume) and internal hybrid
construction. Consequently the parts place a
larger than usual stress on their solder joints
and leads if these are the only method of
attachment. Using an adhesive between
component body and PCB can reduce this
stress considerably. If the final system is to be
subjected to shock and vibration testing, then
using adhesive attachment is essential to
ensure the parts pass these environmental
tests.
The Recom SMD DC-DC converters all have a
stand-off beneath the component for the
application of adhesive to be placed, without
interfering with the siting of the component.
The method of adhesive dispensing and curing,
plus requirements for environmental test and
in-service replacement will determine suitability
of adhesives rather than the component itself.
However, having a thermoset plastic body,
thermoset epoxy adhesive bonding between
board and component is the recommended
adhesive chemistry.
If the reflow stage is also to be used as a cure
for a heat cure adhesive, then the component
is likely to undergo high horizontal acceleration
and deceleration during the pick and place
operation. The adhesive must be sufficiently
strong in its uncured (green) state, in order to
keep the component accurately placed.
Adhesive Placement
The parts are fully compatible with the 3 main
methods of adhesive dispensing; pin transfer,
printing and dispensing. The method of placing
adhesive will depend on the available processes
in the production line and the reason for using
adhesive attachment. For example, if the part
is on a mixed though-hole and SMD board,
adhesive will have to be placed and cured prior
to reflow. If using a SMD only board and heat
cure adhesive, the reflow may be used as the
cure stage. If requiring adhesive for shock
and vibration, but using a conformal coat, then
it may be possible to avoid a separate
adhesive alltogether, and the coating alone
provides the mechanical restraint on the
component body.
A-17
DC-DC Converter Applications
Patterns for dispensing or printing adhesive are
given for automatic lines. If dispensing
manually after placement the patterns for UV
cure are easily repeated using a manual
syringe (even if using heat cure adhesive).If
dispensing manually, dot height and size are not
as important, and the ad-hesive should be
applied after the components have been
reflowed. When dispensing after reflow, a chip
underfill formulation adhesive would be the
preferred choice. These types 'wick' under the
component body and offer a good all round
adhesion from a single dispensed dot.
The patterns allow for the process spread of
the stand-off on the component, but do not
account for the thickness of the PCB tracks.
If thick PCB tracks are to be used, a grounded
copper strip should be laid beneath the centre
of the component (care should be exercised to
maintain isolation barrier limits). The adhesive
should not retard the pins reaching their solder
pads during placement of the part, hence low
viscosity adhesive is recommended.
The height of the adhesive dot, its viscosity and
slumping properties are critical. The dot must
be high enough to bridge the gap between
board surface and component, but low enough
not to slump and spread, or be squeezed by
the component, and so contaminate the solder
pads.
If wishing to use a greater number of dots of
smaller diameter (common for pin transfer
methods), the dot pattern can be changed, by
following a few simple guidelines. As the
number of dots is doubled their diameter
should be halved and centres should be at
least twice the printed diameter from each
other, but the dot height should remain at
0.4mm. The printed dot should always be
positioned by at least its diameter from the
nearest edge of the body to the edge of the dot.
The number of dots is not important, provided good contact between adhesive and body
can be guaranteed, but a minimum of two dots
is recommended.
Cleaning
The thermoset plastic encapsulating material
used for the Recom range of surface mount
DC-DC converters is not fully hermetically
sealed. As with all plastic encapsulated active
devices, strongly reactive agents in hostile
environments can attack the material and the
internal parts, hence cleaning is recommended
in inert solutions (e.g. alcohol or water based
A-18
solvents) and at room temperature in an inert
atmospheres (e.g. air or nitrogen).
A batch or linear aqueous cleaning process
would be the preferred method of cleaning
using a deionised water solution.
Vapour Phase Reflow Soldering
Vapour phase soldering is a still upcoming
soldering practice; therefore there are no
standard temperature profiles available.
Principally, the Lead-free Soldering Profile
recommended by RECOM can be used for
vapour phase soldering. RECOM has tested
large quantities of 8-pin and 10-pin SMD
converters and recommends as an absolute
maximum condition 240°C for 90s dwell time.
In standard applications with small sized
components on a pcb, 230°C and shorter
dwell times will still deliver good results.
After discussions with various contract
manufacturers, we recommended that the
temperature gradients used during preheat and
cooling phases are between 0.5°K/s up to
3°K/s.
Other form factors than 8-pin or 10-pin SMDpackages have not been fully tested under
vapour phase conditions. Please contact
RECOM in this case.
Custom DC-DC Converters
In addition to the standard ranges shown in this
data book, Recom have the capability to
produce custom DC-DC converters designed
to your specific requirements. In general, the
parts can be rapidly designed using computer
based CAD tools to meet any input or output
voltage requirements within the ranges of
Recom standard products (i.e. up to 48V at
either input or output). Prototype samples can
also be produced in short timescales.
Custom parts can be designed to your
specification, or where the part fits within a
standard series, the generic series specification can be used. All custom parts receive the
same stringent testing, inspection and quality
procedures, as standard products. However
there is a minimum order quantity as the
additional documentation and administrative
tasks must be covered in terms of costs.
A general figure for this MOQ can be around
3000pcs of low wattage converters
(0,25W ~ 2W), 1000pcs medium sized
wattage (2W~15W) and 500pcs for higher
wattages (> 20W).
2014
Recom custom parts are used in many
applications, which are very specific to the
individual customer, however, some typical
examples are:
●
●
●
●
●
●
●
ECL Logic driver
Multiple cell battery configurations
Telecommunications line equipment
Marine apparatus
Automotive electronics
LCD display power circuitry
Board level instrumentation systems
To discuss your custom DC-DC converter
requirements, please contact Recom technical
support desk or your local distributor.
Tin Whisker Mitigation
The use of pure tin coating has caused
considerable customer concern about the
possibility of tin whisker formation. Although it
is the opinion of Recom that the risks of
converter failure due to tin whisker formation
are vanishingly small (the only actual recorded
failures due to tin whiskers were in exceptional
environments such as deep space or as a
contributary factor to corona discharge
flashover in a UHV transformer), we have
undertaken tin whisker mitigation procedures
as recommended by Jedec in their JP002
guidelines.
Through Hole Devices:
The pins used in all of our through-hole
converters are made of hard silver-copper
alloy. The pins are then nickel underplated to
0.5µm before being pure tin electroplated to
6µm thickness. This thickness of overplating is
a compromise between reasonable
manufacturing costs and having a thick
enough coating to impair tin whisker formation.
The surface is not ‘brightened’, also to
mitigate tin whisker formation.
Finally the pins are annealed according to JIS
C3101. This reduces any residual forming
stresses, which is one of the other potential
causes of tin whisker formation
Surface Mount Devices:
The carrier frames used in our SMD converters are made from DF42N nickel alloy which
is pure tin plated. The pins are hot dipped in
Sn-Ag-Cu solder just before injection molding.
Hot dipping with SnAg4 or SnAgCu is generally
an effective mitigation practice and considered
whisker free.
www.recom-international.com
Innoline Application Notes
Contents
Innoline Application Notes
●
Positive-to-Negative Converters
●
EMC Considerations
R-78xx-0.5 Series
R-78Cxx-xx Series
●
Soft Start Circuit
R-78Axx-0.5SMD Series
R-78HBxx-xx Series
R-78xx-1.0 Series
R-62xxP_D Series
R-78Axx-1.0SMD Series
Pos-to-Neg Circuit Ideas
R-78Bxx-1.0 Series
EMC Considerations
Although all Innoline converters are switching regulators, and contain internal high frequency oscillators, they have been designed to minimise
radiated and conducted emissions.
If the end-application is particularly sensitive to conducted interference, the following input filter can be used for all R-78, R-5xxx, R-6xxx and
R-7xxx converters.
R-78xx EMC Filter
Class B: C1=10µF MLCC, C2=10µF MLCC, L1=56µH
Vin
L1
R-78Cxx EMC Filter
Class A: C1=C2=10µF MLCC, L1=10µH
Input
Class B: C1=22µF MLCC, C2=10µF MLCC,
L1=56µH
C1
C2
Vout
GND
Output
R-78Exx EMC Filter
Class A: C1=C2=10µF MLCC, L1=10µH
Class B: C1=C2=10µF MLCC, L1=33µH
Output Soft Start
Innoline converters with Vadj pins (R-78AAxx-xxSMD, R-5xxx, R-6xxx and R-7xxx families) can be fitted with an external circuit to create an
output soft start. Any general purpose PNP transistor and diode can be used for TR1 and D1 and typical values for R1 = 100K and C1 = 10µF.
+Vin
Vcc
+Vout
Ctrl GND Vadj
On/Off
R1
D1
TR1
C1
GND
www.recom-international.com
2014
A-19
Innoline Application Notes
Positive to Negative Converters
Features
●
Innoline
Switching
Regulators
●
●
●
Innoline Switching Regulators can also be used
to convert a positive voltage into a negative
voltage
The standard parts can be used - only two extra
capacitors are required
Fixed and variable output voltages are available.
Input voltage range can be lower than the output
voltage for higher output voltages
Positive-to-Negative Switching Regulators Selection Guide
Series
R-78xx-0.5
R-78AAxx-0.5SMD
R-78xx-1.0
R-78AAxx-1.0SMD
R-78Bxx-1.0
R-78Bxx-1.5
R-78HBxx-0.5
Maximum
Output
Current
-0.4A
-0.2A
-0.4A
-0.2A
Input Voltages
(VDC)
min.
max.
4.75 – 28,
5.0 – 26, 8.0 – 18
4.75 – 28,
5.0 – 26, 8.0 – 18
Output Voltages
(VDC)
No. of
Outputs
Case
Adjustable
Vout?
-1.5, -1.8, -2.5, -3.3, -5.0,
-6.5, -9.0, -12, -15
-1.5, -1.8, -2.5, -3.3, -5.0,
-6.5, -9.0, -12, -15
S
SIP3
No
Max
Cap.
Load
220µF
S
SMD
Yes
220µF
No
220µF
No
100µF
-1A/-0.8A/-0.6A
9 - 28, 9-26
-1.8, -2.5, -3.3, -5, -9, -12
S
SIP12
Yes
Not recommended to be used in this mode due to the reduced efficiency and higher Ripple & Noise figures.
470µF
Not recommended to be used in this mode due to the reduced input and output voltage range
Not recommended to be used in this mode due to the reduced input and output voltage range
-0.6A
4.75 – 28,
-1.5, -1.8, -2.5, -3.3, -5.0,
S
SIP3
-0.4A
8.0 – 28, 8.0 – 26
-6.5, -9.0,
-0.3A
8.0 – 18
-12, -15
Not recommended to be used in this mode due to the reduced input and output voltage range
-0.4A/-0.35A
15 – 65,
-3.3, -5.0,-6.5
S
SIP3
-0.3A/-0.25A/-0.2A
15 – 62, 15 – 59, 15 – 56,
-9.0, -12, -15
-0.2A
20 – 48
-24
R-5xxxP/DA
Not recommended to be used in this mode due to the reduced input and output voltage range
R-61xxP/D
Not recommended to be used in this mode as R-78B series offer a lower cost alternative
R-62xxP/D
R-7xxxP/D
Circuit Ideas
A-20
2014
www.recom-international.com
INNOLINE
Positive to Negative Converter
DC/DC-Converter
0V
0V
+Vin
C1 and C2 are required
and should be fitted close
to the converter pins.
3
1
R-78Bxx-1.0
Maximum capacitive load
including C2 is 220µF
2
C1
C2
-Vout
Pin Connections
Pin #
Negative
Output
1
+Vin
2
-Vout
3
GND
RECOM
R-785.0-05
****
Positive
Output
+Vin
GND
+Vout
R-78xx-0.5
Series
Positive to
Negative
Converter
1 2 3
Selection Guide
Part
Number
SIP3
Input
Range (1)
(V)
Output
Voltage
(V)
Output
Current
(A)
Efficiency
Min. Vin
Max. Vin
(%)
(%)
External Capacitors
C1
C2*
R-781.5-0.5
4.75 – 28
-1.5
-0.4
68
67
10µF/35V
22µF/6.3V
R-781.8-0.5
4.75 – 28
-1.8
-0.4
71
70
10µF/50V
22µF/6.3V
R-782.5-0.5
4.75 – 28
-2.5
-0.4
75
76
10µF/50V
22µF/6.3V
R-783.3-0.5
4.75 – 28
-3.3
-0.4
77
80
10µF/50V
22µF/6.3V
R-785.0-0.5
4.75 – 28
-5.0
-0.4
79
84
10µF/50V
22µF/10V
R-786.5-0.5
5.0 – 26
-6.5
-0.3
81
86
10µF/50V
10µF/10V
R-789.0-0.5
8.0 – 18
-9.0
-0.2
87
89
10µF/50V
10µF/16V
R-7812-0.5
8.0 – 18
-12
-0.2
87
90
10µF/50V
10µF/25V
R-7815-0.5
8.0 – 18
-15
-0.2
87
91
10µF/50V
10µF/25V
* Maximum capacitive load including C2 is 220µF
Application Example (see also Circuit Ideas at end of section)
+Vin
1
R-78xx-0.5
3
+Vout
Derating-Graph
(Ambient Temperature)
2
120
100
1
R-78xx-0.5
3
Maximum capacitive
load ±220µF
2
C1
C2
-Vout
www.recom-international.com
2014
Output Power (%)
0V
0V
80
60
40
20
0
Safe Operating Area
-40
0
25
50
Operating Temperature (°C)
85
75
100
71
A-21
INNOLINE
Positive to Negative Converter
DC/DC-Converter
0V
0V
+Vin
C1
10
On/Off
4,5
R-78AAxx0.5SMD
1,2
(Referenced to
-Vout)
R1
6
3,7
8,9
C1 and C2 are required
and should be fitted close
to the converter pins.
C2
Maximum capacitive load
including C2 is 220µF
R2
-Vout
Pin Connections
Pin #
Negative
Output
1,2
+Vin
3,7,8,9
-Vout
4,5
GND
6
-Vout Adj.
10
On/Off
10 9 8 7 6
Positive
Output
+Vin
GND
+Vout
+Vout Adj.
On/Off
R-78AA
xx-0.5 SMD
Positive to
Negative
Converter
RECOM
R-78Axx-0.5SMD
xxxx
1 2 3 4 5
Selection Guide
Part
Number
SIP3
Input
Range (1)
(V)
Output
Voltage
(V)
Output
Current
(A)
Efficiency
Min. Vin
Max. Vin
(%)
(%)
External Capacitors
C1
C2
R-78AA1.5-0.5SMD
4.75 – 28
-1.5
-0.4
68
67
10µF/35V
22µF/6.3V
R-78AA1.8-0.5SMD
4.75 – 28
-1.8
-0.4
71
70
10µF/50V
22µF/6.3V
R-78AA2.5-0.5SMD
4.75 – 28
-2.5
-0.4
75
76
10µF/50V
22µF/6.3V
R-78AA3.3-0.5SMD
4.75 – 28
-3.3
-0.4
77
80
10µF/50V
22µF/6.3V
R-78AA5.0-0.5SMD
4.75 – 28
-5.0
-0.4
79
84
10µF/50V
22µF/10V
R-78AA6.5-0.5SMD
5.0 – 26
-6.5
-0.3
81
86
10µF/50V
10µF/10V
R-78AA9.0-0.5SMD
8.0 – 18
-9.0
-0.2
87
89
10µF/50V
10µF/16V
R-78AA12-0.5SMD
8.0 – 18
-12
-0.2
87
90
10µF/50V
10µF/25V
R-78AA15-0.5SMD
8.0 – 18
-15
-0.2
87
91
10µF/50V
10µF/25V
* Maximum capacitive load including C2 is 220µF
Application Example (see also Circuit Ideas at end of section)
+Vin
1,2
On/Off
10
R-78A(A)xx0.5SMD
3,7
8,9
+Vout
4,5
R1
6
Maximum capacitive
load ±220µF
(Ambient Temperature)
R2
0V
120
100
0V
1,2
C1
Optocoupler
10
R-78A(A)xx0.5SMD
3,7
8,9
6
Output Power (%)
Optocoupler
A-22
Derating-Graph
4,5
R1
C2
R2
-Vout
2014
80
60
40
20
0
Safe Operating Area
-40
0
25
50
Operating Temperature (°C)
85
75
100
71
www.recom-international.com
INNOLINE
R-78AAxx-0.5 SMD
Positive to Negative
DC/DC-Converter
Table 1: Adjustment Resistor Values
0.5Adc
Vout (nom.)
R-78AA1.8
-0.5SMD
1.8Vdc
Vout (adj)
R1
-1.5 (V)
3KΩ
R2
R-78AA2.5
-0.5SMD
2.5Vdc
R1
R-78AA3.3
-0.5SMD
3.3Vdc
R2
R1
R-78AA5.0
-0.5SMD
5.0Vdc
R2
R1
R2
R-78AA6.5
-0.5SMD
6.5Vdc
R1
R-78AA9.0
-0.5SMD
9.0Vdc
R2
R1
R-78AA12
-0.5SMD
12.0Vdc
R2
R1
R2
200Ω
-1.8 (V)
12KΩ
-2.5 (V)
11.8KΩ
-3.0 (V)
4.64KΩ
44.2KΩ 88.4KΩ
17KΩ
-3.3 (V)
27KΩ
6.7KΩ
-3.6 (V)
60.4KΩ
42KΩ
14KΩ
-3.9 (V)
28KΩ
58KΩ
23KΩ
-4.5 (V)
11.3kΩ
180KΩ
49KΩ
26KΩ
17KΩ
-4.9 (V)
7.15kΩ
850KΩ
77kΩ
36KΩ
24KΩ
-5.0 (V)
6.34kΩ
86kΩ
39KΩ
26KΩ
-5.1 (V)
5.9kΩ
231kΩ
97KΩ
42KΩ
28KΩ
-5.5 (V)
3.9kΩ
56.2kΩ
160KΩ
56KΩ
36KΩ
112KΩ
63KΩ
24.6KΩ 400KΩ
125KΩ
-6.5 (V)
14kΩ
-8.0 (V)
2.32kΩ
-9.0 (V)
10.7KΩ
200KΩ
-10 (V)
4.75KΩ
54.9KΩ 345KΩ
-11 (V)
1.65KΩ
16.5KΩ 740KΩ
-12 (V)
3.6KΩ
-12.6 (V)
0Ω
180KΩ
Typical Application
1,2
+
10
Vin=15VDC
R-78A(A)120.5SMD
3,7
8,9
+Vout
4,5
26k
6
+5V
100k
+7.5V
200k
+9V
+12V
-
0V
1,2
10µF
10
R-78A(A)120.5SMD
3,7
8,9
4,5
6
22µF
26k
-5V
100k
-7.5V
200k
-9V
-12V
Dual Rail Selectable Output Voltage Power Supply
www.recom-international.com
2014
-Vout
A-23
INNOLINE
Positive to Negative Converter
DC/DC-Converter
0V
0V
+Vin
1
R-78Bxx1.0 Series
Positive to
Negative
Converter
C1 and C2 are required
and should be fitted close
to the converter pins.
3
R-78Bxx-1.0
Maximum capacitive load
including C2 is 220µF
2
C1
C2
-Vout
Pin Connections
Pin #
Negative
Output
1
+Vin
2
-Vout
3
GND
Positive
Output
+Vin
GND
+Vout
RECOM
R-78B5.0-1.0
****
Pb
1 2 3
Selection Guide
Part
Number
SIP3
Input
Range (1)
(V)
Output
Voltage
(V)
Output
Current
(A)
Efficiency
Min. Vin
Max. Vin
(%)
(%)
External Capacitors
C1
C2*
R-78B1.5-1.0
4.75 – 28
-1.5
-0.6
70
68
10µF/50V
22µF/6.3V
R-78B1.8-1.0
4.75 – 28
-1.8
-0.6
72
72
10µF/50V
22µF/6.3V
R-78B2.5-1.0
4.75 – 28
-2.5
-0.6
75
77
10µF/50V
22µF/6.3V
R-78B3.3-1.0
4.75 – 28
-3.3
-0.6
77
80
10µF/50V
22µF/6.3V
R-78B5.0-1.0
6.5 – 28
-5.0
-0.6
83
85
10µF/50V
22µF/10V
R-78B6.5-1.0
8.0 – 26
-6.5
-0.4
84
87
10µF/50V
10µF/10V
R-78B9.0-1.0
8.0 – 18
-9.0
-0.4
88
89
10µF/25V
10µF/25V
R-78B12-1.0
8.0 – 18
-12
-0.3
89
90
10µF/25V
10µF/25V
R-78B15-1.0
8.0 – 18
-15
-0.3
89
91
10µF/25V
10µF/25V
* Maximum capacitive load including C2 is 220µF
Application Example (see also Circuit Ideas at end of section)
+Vin
1
R-78Bxx-1.0
3
2
+Vout
Derating-Graph
Maximum capacitive
(Ambient Temperature)
load ±220µF
1
R-78Bxx-1.0
Output Power (%)
0V
0V
3
2
C1
C2
-Vout
A-24
120
100
2014
80
60
40
20
0
Safe Operating Area
-40
0
25
50
Operating Temperature (°C)
85
75
100
71
www.recom-international.com
INNOLINE
Positive to Negative Converter
DC/DC-Converter
*2
RECOM
R-78Cxx-1.0
XXXX Pb
1
+Vin
C1
10µ/50V
2
*1
C2
10µ/50V
GND
Pin Connections
Pin #
Negative
Output
1
+Vin
2
-Vout
3
GND
3
GND
-Vout
RECOM
R-78C5.0-1.0
****
Positive
Output
+Vin
GND
+Vout
R-78Cxx1.0 Series
Positive to
Negative
Converter
1 2 3
Selection Guide
Part
Number
SIP3
Input
Range (1)
(V)
Output
Voltage
(V)
Output
Current
(A)
Efficiency
Min. Vin
Max. Vin
(%)
(%)
R-78C1.8-1.0
5 – 38
-1.8
-0.8
69
70
R-78C3.3-1.0
7 – 37
-3.3
-0.8
77
80
R-78C5.0-1.0
8 – 35
-5.0
-0.7
79
83
R-78C9.0-1.0
12 – 31
-9.0
-0.6
85
87
R-78C12-1.0
15 – 28
-12
-0.5
87
89
R-78C15-1.0
18 – 25
-15
-0.5
89
90
Application Example (see also Circuit Ideas at end of section)
1
+Vin
C1
RECOM
R-78Cxx-1.0
XXXX Pb
10µF/50V
3
+Vout
Derating-Graph
(Ambient Temperature)
2
GND (Com)
GND
*1
1
C2
10µF/50V
RECOM
R-78Cxx-1.0
XXXX Pb
Output Power (%)
*2
3
2
When: Vin ¹ | ±Vout |
120
100
-Vout
80
60
40
20
0
Safe Operating Area
-40
0
25
50
Operating Temperature (°C)
85
75
100
68
Dual Outputs (two converters)
www.recom-international.com
2014
A-25
INNOLINE
Positive to Negative Converter
0V
0V
+Vin
C1 and C2 are required
and should be fitted close
to the converter pins.
3
1
R-78HBxx-0.5
Maximum capacitive load
including C2 is 100µF
2
C1
C2
-Vout
Pin Connections
Pin #
Negative
Output
1
+Vin
2
-Vout
3
GND
Positive
Output
+Vin
GND
+Vout
RECOM
DC/DC-Converter
R-78HBxx0.5 Series
Positive to
Negative
Converter
R-78HB5.0-0.5
****
Pb
1 2 3
Selection Guide
Part
Number
SIP3
Input
Range (1)
(V)
Output
Voltage
(V)
Output
Current
(A)
Efficiency
Min. Vin
Max. Vin
(%)
(%)
External Capacitors
C1
C2*
R-78HB3.3-0.5
15 – 65
-3.3
-0.4
78
75
1µF/100V
22µF/6.3V
R-78HB5.0-0.5
15 – 65
-5.0
-0.4
82
80
1µF/100V
22µF/10V
R-78HB6.5-0.5
15 – 65
-6.5
-0.35
84
82
1µF/100V
22µF/10V
R-78HB9.0-0.5
15 – 62
-9.0
-0.3
87
85
1µF/100V
10µF/16V
R-78HB12-0.5
15 – 59
-12
-0.25
88
86
1µF/100V
10µF/25V
R-78HB15-0.5
15 – 56
-15
-0.2
89
87
1µF/100V
10µF/25V
R-78HB24-0.5
15 – 48
-24
-0.2
89
87
1µF/100V
10µF/35V
* Maximum capacitive load including C2 is 100µF
Application Example (see also Circuit Ideas)
+Vin
1
3
R-78HBxx-0.5
2
+Vout
Maximum capacitive
(Ambient Temperature)
load ±100µF
120
100
1
Output Power (%)
0V
0V
3
R-78HBxx-0.5
2
C1
C2
-Vout
A-26
Derating-Graph
2014
80
60
40
20
0
Safe Operating Area
-40
0
25
50
Operating Temperature (°C)
85
75
100
71
www.recom-international.com
INNOLINE
Positive to Negative Converter
DC/DC-Converter
0V
+Vin
On/Off
(Referenced to
-Vout)
R-62xxP/D
SIP12
Positive to
Negative
Converter
0V
2,3,4
C1
R-62xxP/D
1
5,6
7,8
C1 and C2 are required
and should be fitted close
to the converter pins.
9,10,
11
R1
12
C2
R2
Maximum capacitive load
including C2 is 220µF
-Vout
Pin Connections
Pin #
Negative
Output
2,3,4
+Vin
5,6,7,8
-Vout
9,10,11
GND
12
-Vout Adj.
1
On/Off
Positive
Output
+Vin
GND
+Vout
+Vout Adj.
On/Off
RECOM
R-6212P
1 2 3 4 5 6 7 8 9 10 11 12
Selection Guide
Part
Number
SIP3
Input
Range (1)
(V)
Output
Voltage
(V)
Output
Current
(A)
Efficiency
Min. Vin
Max. Vin
(%)
(%)
External Capacitors
C1
C2*
R-621.8P/D
9 – 28
-1.8 (-1.5~-3.6)
-1.0
72
65
10µF/50V
100µF/6.3V
R-622.5P/D
9 – 28
-2.5 (-1.5~-4.5)
-1.0
76
72
10µF/50V
100µF/6.3V
R-623.3P/D
9 – 28
-3.3 (-1.8~-6V)
-1.0
79
76
10µF/50V
100µF/10V
R-625.0P/D
9 – 28
-5.0 (-1.8~-9V)
-1.0
81
80
10µF/50V
100µF/10V
R-629.0P/D
9 – 26
-9.0 (-3.3~-15V)
-0.8
84
85
10µF/50V
100µF/25V
R-6212P/D
9 – 26
-12 (-3.3~-15V)
-0.6
86
88
10µF/50V
100µF/25V
* Maximum capacitive load including C2 is 220µF
Max output current calculation:
Internal power dissipation
(1W) = Io x Vo x (1-Efficiency)
Io = 1(W) / Vo x (1-Efficiency)
Example : R-625.0P
at Vin = +9VDC, Vout=-5.0V
Efficiency = 80% (see ”Selection Guide” table)
Io = 1W / 5V x (1-0.8) = -1000mA
at Vin = +9VDC, Vout=-8.0V (with trim)
Efficiency = 80% (see ”Selection Guide” table)
Io = 1W / 8V x (1-0.8) = -625mA
Ambient Temperature (°C)
Derating
90
85
80
60
40
20
0
0.5 0.7
1
1.5
Internal Power Dissipation (W)
www.recom-international.com
2014
A-27
R-62xxP_D
Positive to Negative
INNOLINE
DC/DC-Converter
Remote On/Off Control Application Example
+Vin
2,3,4
On/Off
1
R-6xxxP
R1
12
5,6
7,8
+Vout
9,10,11
100µF
R2
0V
0V
Optocoupler
2,3,4
C1
1
R-62xxP
9,10,
11
R1
12
5,6
7,8
Maximum capacitive
load ±220µF
C2
R2
Optocoupler
-Vout
Table 1: Adjustment Resistor Values
-1Adc
Vout (nominal)
R-621.8P/D
R-622.5P/D
R-623.3P/D
1.8VDC
2.5VDC
3.3VDC
Vout (adj)
R1
1.5
13.6KΩ
R2
R2
R1
R2
5VDC
R1
R2
3.3KΩ
1.8
A-28
R1
R-625.0P/D
8.2KΩ
3.1KΩ
820Ω
15KΩ
5.1KΩ
1.5KΩ
13KΩ
3.6KΩ
51KΩ
7.0KΩ
2.0
10KΩ
2.5
5.1KΩ
3.0
2.5KΩ
10KΩ
3.3
1.7KΩ
5.9KΩ
3.6
1.2KΩ
3.9KΩ
18KΩ
14KΩ
3.9
2.8KΩ
9.1KΩ
20KΩ
4.5
1.6KΩ
3.9KΩ
60KΩ
9.7KΩ
5.0
2.4KΩ
5.1
2.2KΩ
60KΩ
5.5
1.6KΩ
15KΩ
6.0
1.1KΩ
7.2KΩ
7.0
2.8KΩ
8.0
1.5KΩ
2014
www.recom-international.com
Positive to Negative
Circuit Ideas
INNOLINE
DC/DC-Converter
Application Examples
Negative Voltage Doubler
0V
0V
-12V
1
R-78B12-1.0
3
2
10µF/
25V
10µF/
25V
-24V @ 300mA
12V Battery Stabilisor
Vbatt =
8~18V
-Ve
12V
1
+Ve
3
R-7812-0.5
2
10µF/
25V
10µF/
25V
0V
Negative Rail Generator for Asymmetric Rails
L
N
0.1µF
RAC1012SB
C1
1
R-7805-0.5
47µF/
16V
C2
+12V @ 655mA
0V
3
2
10µF/
25V
C3
C1
RAC10 AC/DC Converter
C3
C4
R-78
27.2mm
C2
C4
22µF/
10V
-5V @ -400mA
Ultra-compact low noise
regulated and protected
AC/DC dual output supply.
60mm
www.recom-international.com
2014
A-29
Powerline Application Notes
Contents
Powerline DC/DC Application
Notes
Switching Frequency
●
Undervoltage Lockout Tables
Output Ripple and Noise
●
Output Voltage Trim Tables
●
Powerline Heat Sinks
●
Common Mode Chokes for EMC
Transient Recovery Time
●
Powerline Definitions and Testing
Current Limiting
Introduction
Fold Back Current Limiting
Input Voltage Range
Isolation
Pi Filter
Break Down Voltage
Output Voltage Accuracy
Temperature Coefficient
Input Fuse
Voltage Balance
Ambient Temperature
Earthing
Line Regulation
Operating Temperature Range
Combining Converters
Load Regulation
Storage Temperature Range
DC Inputs
Heat Sink Dimensions
Powerline AC/DC Application
Notes
Efficiency
Common Mode Chokes for EMC
Recom offers a range of Common Mode Chokes useful for EMI Filtering to meet the requirements of EN-55022, Class B.
The component values given are suggested values and may need to be optimised to suit the application. The effectiveness of any filter
network is heavily dependent on using quality capacitors, the layout of the board and having a low impedance path to ground.
See section on filtering elsewhere in the Application Notes for more details.
Class B EMC Filter Suggestion
Standard EMC Filter
C4
Input
+
+
C1
C2
Output
100nF
(fit close
to pins)
CMC
C3
A-30
2014
www.recom-international.com
Powerline DC-DC Application Notes
RP15-SO_DO and RP15-SOW_DOW Series Only
470pF/ 3kV
Vout+
L1
Input
+
+ +
C1
C2
RP15-SO_DO
Output
C3
Vout-
CMC
470pF/ 3kV
RP30-SF_DF and RP30-SF W_DFW Series Only
C4
Vout+
RP30-SF_DF
RP30-SFW_DFW
Input
+
+
+
C1
C2
C3
Trim or
Common
VoutCMC-1
CMC-2
C5
C6
www.recom-international.com
2014
A-31
Powerline DC-DC Application Notes
Component Values
All capacitors MLCC (Multi Layer Ceramic Capacitor).
RP08-A
Vin = 12VDC nom., C1=4.7µF/50V, C2=Not Required, C3,C4=1nF/3kV, WE 7448229004 350µH
Vin = 24VDC nom., C1=6.8µF/50V, C2=Not Required, C3,C4=1nF/3kV, WE 7448229004 350µH
Vin = 48VDC nom., C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=1nF/3kV, WE 7448229004 350µH
RP08-AW
Vin = 9~36VDC, C1=4.7µF/50V, C2=Not Required, C3,C4=1nF/3kV, WE 7448229004 350µH
Vin = 18~75VDC, C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=1nF/3kV, WE 7448229004 350µH
RP10-E
RP12-A
Vin = 12VDC nom., C1=3.3µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448229004 350µH
Vin = 24VDC nom., C1=4.7µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448229004 350µH
Vin = 48VDC nom., C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=1nF/2kV, WE 7448229004 350µH
RP10-EW
RP12-AW
Vin = 9~36VDC, C1=3.3µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448229004 350µH
Vin = 18~75VDC, C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=1nF/2kV, WE 74482210002 175µH
RP15-A
Vin = 12VDC nom., C1=10µF/25V, C2=10µF/25V, C3,C4=470pF/2kV, WE 74482210002 175µH
Vin = 24VDC nom., C1=6.8µF/50V, C2=6.8µF/50V, C3,C4=470pF/2kV, WE 7448229004 350µH
Vin = 48VDC nom., C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=470pF/2kV, WE 74466240007 700µH
RP15-AW
Vin = 9~36VDC, C1=6.8µF/50V, C2=6.8µF/50V, C3,C4=470pF/2kV, WE 7448227005 450µH
Vin = 18~75VDC, C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=470pF/2kV, WE 7448229004 350µH
RP15-O
Vin = 12VDC nom., C1=10µF/25V, C2=10µF/25V, L1 = 10µH, WE 744822100002 175µH
Vin = 24VDC nom., C1=6.8µF/50V, C2=6.8µF/50V, L1 = 10µH, WE 744822100002 175µH
Vin = 48VDC nom., C1=2.2µF/100V, C2=2.2µF/100V, L1 = 18µH, WE 744822100002 175µH
RP15-OW
Vin = 9~36VDC, C1, C2, C3 =6.8µF/50V, WE 744822100002 175µH
Vin = 18~75VDC, C1=2 x 2.2µF/100V in parallel, C2,C3 =2.2µF/100V, L1 = 33µH, WE 7448229004 350µH
RP15-F
Vin = 12VDC nom., C1=4.7µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448229004 350µH
Vin = 24VDC nom., C1=3.3µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448229004 350µH
Vin = 48VDC nom., C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=1nF/2kV, WE 7448229004 350µH
RP15-FW
Vin = 9~36VDC, C1=2.2µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 18~75VDC, C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=1nF/2kV, WE 7448229004 350µH
RP20-F
Vin = 12VDC nom., C1=4.7µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 24VDC nom., C1=4.7µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 48VDC nom., C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=1nF/2kV, WE 7448227005 450µH
RP20-FW
Vin = 9~36VDC, C1=4.7µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 18~75VDC, C1=2.2µF/100V, C2=2.2µF/100V, C3,C4=1nF/2kV, WE 7448229004 350µH
RP30-E
Vin = 12VDC nom., C1=4.7µF/25V, C2=Not Required, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 24VDC nom., C1=6.8µF/50V, C2=6.8µF/50V, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 48VDC nom., C1=2.2µFII2.2µF/100V, C2=2.2µFII2.2µF/100V, C3,C4=1nF/2kV, WE 7448227005 450µH
RP30-EW
Vin = 9~36VDC, C1=6.8µF/50V, C2=6.8µF/50V, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 18~75VDC, C1=2.2µF II 2.2µF/100V, C2=2.2µF II 2.2µF/100V, C3,C4=1nF/2kV, WE 7448227005 450µH
Continued on next page
A-32
2014
www.recom-international.com
Powerline DC-DC Application Notes
RP30-F
Vin = 12VDC nom., C1, C2, C3 =10µF/25V, C4, C5, C6=1nF/2kV, CMC1 = WE 744841330 30µH, CMC2 =
WE 744842565 65µH
Vin = 24VDC nom., C1, C2, C3 =4.7µF/50V, C4, C5, C6=1nF/2kV, CMC1 = WE 744841330 30µH, CMC2 =
WE 744842565 65µH
Vin = 48VDC nom., C1, C2, C3 =2.2µF/100V, C4, C5, C6=1nF/2kV, CMC1 = WE 744841330 30µH, CMC2 =
WE 744842565 65µH
RP30-FW
Vin = 9~36VDC, C1, C2, C3 =4.7µF/50V, C4, C5, C6=1nF/2kV, CMC1 = WE 744841330 30µH, CMC2 =
WE 744842565 65µH
Vin = 18~75VDC, C1, C2, C3 =4.7µF/50V, C4, C5, C6=1nF/2kV, CMC1 = WE 744841330 30µH, CMC2 =
WE 744842565 65µH
RP40-G
Vin = 12VDC nom., C1=4.7µF/50V, C2=Not Required, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 24VDC nom., C1=6.8µF/50V, C2=6.8µF/50V, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 48VDC nom., C1=2.2µF II 2.2µF/100V, C2=2.2µF II 2.2µF/100V, C3,C4=1nF/2kV, WE 7448640395 820µH
RP40-GW
Vin = 9~36VDC, C1=4.7µF/50V, C2=4.7µF/50V, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 18~75VDC, C1=2.2µF II 2.2µF/100V, C2=2.2µF II 2.2µF/100V, C3,C4=1nF/2kV, WE 7448640395 820µH
RP60-G
Vin = 24VDC nom., C1=4.7µF/50V, C2=4.7µF/50V, C3,C4=1nF/2kV, WE 7448227005 450µH
Vin = 48VDC nom., C1=2.2µF II 2.2µF/100V, C2=2.2µF II 2.2µF/100V, C3,C4=1nF/2kV,WE 7448640395 820µH
Recommended PCB Layouts
C3
C1
4
3
1
2
C2
100
nF
Standard EMC Filter
CMC
C4
470
pF
C1
RP15-O Open Frame
Converters
4
3
1
2
CMC
C2 C3
L1
470
pF
www.recom-international.com
2014
A-33
Powerline DC-DC Application Notes
Recommended PCB Layouts
C6
C5
RP30-S_DF
RP30-S_DFW
C1
4
3
1
2
CMC-1
C2
3
4
C3
2
1
CMC-2
C4
General Information about Recom Common Mode Chokes
Recom common mode chokes are all RoHS conform. Maximum Rated Voltage = 500VDC
Operating Temperature = -40°C ~ +105°C
A-34
2014
www.recom-international.com
Powerline DC-DC Application Notes
Definitions and Testing
General Test Set-Up
DC Power
Source
A
+V
A
DC/DC
Converter
under Test
V
V ( VDC or VRMS )
Adjustable
load
-V
Figure 1-3: General DC/DC converter test set-up
Note: If the converter is under test with
remote sense pins, connect these pins
to their respective output pins. All tests
are made in ”Local sensing“ mode.
Input Voltage Range
The minimum and maximum input voltage limits within which a converter
will operate to specifications.
PI Filter
An input filter, consisting of two capacitors,
connected before and after a series
inductor to reduce input reflected ripple
current. The effective filter is C1/L
+ L/C2, so the inductor filter element is
doubly effective.
Output Voltage Accuracy
With nominal input voltage and rated
output load from the test set-up, the DC
output voltage is measured with an
accurate, calibrated DC voltmeter.
Output voltage accuracy is the difference
between the measured output voltage
and specified nominal value as a
percentage. Output accuracy (as a %) is
then derived by the formula:
L
Input
C1
C2
Output
Figure 2: PI Filter
Vout – Vnom
Vnom N
X100
Vnom is the nominal output specified in
the converter data sheet.
Voltage Balance
For a multiple output power converter,
the percentage difference in the voltage
level of two outputs with opposite polarrities and equal nominal values.
Line Regulations
Make and record the following measurements with rated output load at +25°C:
● Output voltage at nominal line
(input) voltage.
Vout N
● Output voltage at high line (input)
voltage.
Vout H
● Output voltage at low line (input)
voltage.
Vout L
The line regulation is Vout M (the maximum of the two deviations of output) for
the value at nominal input in percentage.
www.recom-international.com
2014
Vout M – Vout N
Vout N
X100
A-35
Powerline DC-DC Application Notes
Definitions and Testing
Make and record the following measurements with rated output load at +25°C:
● Output voltage with rated load
connected to the output. (Vout FL)
● Output voltage with no load or the
minimum specified load for the
DC-DC converter. (Vout ML)
Load regulation is the difference between
the two measured output voltages as a
percentage of output voltage at rated
load.
Efficiency
The ratio of output load power consumption
to input power consumption expressed
as a percentage. Normally measured at
full rated output power and nominal line
conditions.
Switching Frequency
The rate at which the DC voltage is switched in a DC-DC converter or switching
power supply. The ripple frequency is
double the switching frequency in pushpull designs.
Output Ripple and Noise
Because of the high frequency content
of the ripple, special measurement techniques must be employed so that correct
measurements are obtained. A 20MHz
bandwidth oscilloscope is used, so that
all significant harmonics of the ripple
spike are included.
This noise pickup is eliminated as shown
in Figure 3, by using a scope probe with
an external connection ground or ring
and pressing this directly against the
output common terminal of the power
converter, while the tip contacts the voltage output terminal. This provides the
shortest possible connection across the
output terminals.
Load Regulation
Vout ML – Vout FL
Vout FL
X100
Figure 3:
A-36
2014
www.recom-international.com
Powerline DC-DC Application Notes
Definitions and Testing
Output Ripple and Noise (continued)
Transient Recovery Time
Figure 4 shows a complex ripple voltage
waveform that may be present on the
output of a switching power supply.
There are three components in the waveform, first is a charging component that
originates from the output rectifier and
filter, then there is the discharging component due to the load discharging the
output capacitor between cycles, and
finally there are small high frequency
switching spikes imposed on the low
frequency ripple.
Peak-Peak
Amplitude
Time
Figure 4: Amplitude
The time required for the power supply
output voltage to return to within a specified percentage of rated value, following a step change in load current.
Transient
Recovery Time
Overshoot
Output
Voltage
5V + U
5V
Undershoot
5V - L
V out
U: upper limit
L: lower limit
Load
I out
Time
Figure: 5 Transient Recovery Time
Current Limiting
output current is limited to prevent
damage of the converter at overload
situations. If the output is shorted, the
Fold Back Current Limiting
A method of protecting a power supply
from damage in an overload condition,
reducing the output current as the load
approaches short circuit.
output voltage is regulated down so the
current from the outputs cannot be
excessive.
V out
Rated Io
I out
Figure 6: Fold Back Current LimitingTime
www.recom-international.com
2014
A-37
Powerline DC-DC Application Notes
Definitions and Testing
Isolation
The electrical separation between the
input and output of a converter, (consisting of resistive and capacitive isola-
Break-Down Voltage
The maximum continuous DC voltage,
which may be applied between the input
and output terminal of a power supply
without causing damage.
Typical break-down voltage for DC-DC
converters is 1600VDC because the
equivalent DC isolation for 230VAC
continuous rated working voltage is
1500VDC.
tion) normally determined by transformer characteristics and circuit spacing.
R
Resistive and
Capacitive Isolation
C
Input
Rectifier
and
Regulator
Output
Breakdown Voltage
Figure 7:
Temperature Coefficient
With the power converter in a temperature test chamber at full rated output
load, make the following measurements:
● Output voltage at +25°C ambient
temperature.
● Set the chamber for maximum
operating ambient temperature
and allow the power converter to
stabilize for 15 to 30 minutes.
Measure the output voltage.
● Set the chamber to minimum
operating ambient temperature and
allow the power converter to
stabilize for 15 to 30 minutes.
●
Ambient Temperature
The temperature of the still-air immediately surrouding an operating
power supply. Care should be taken
when comparing manufacturer’s da-
tasheets that still-air ambient temperature and not case temperature is
quoted.
Operating Temperature Range
The range of ambient or case temperature within a power supply at which
it operates safely and meets its
specifications.
Storage Temperature Range
The range of ambient temperatures
within a power supply at non-opera-
ting condition, with no degradation in
its subsequent operation.
A-38
2014
Divide each percentage voltage
deviation from the +25°C ambient
value by the corresponding temperature change from +25°C
ambient.
The temperature coefficient is the higher
one of the two values calculated above,
expressed as percent per change centigrade.
www.recom-international.com
Powerline DC-DC Application Notes
Trim Tables
Some converters from our Powerline offer
the feature of trimming the output voltage in
a certain range around the nominal value
by using external trim resistors.
Because different series use different circuits for trimming, no general equation can
be given for calculating the trim resistors.
Output Voltage Trimming:
The following trimtables give values for
chosing these trimming resistors.
If voltages between the given trim points
are required, extrapolate between the two
nearest given values to work out the resistor required or use a variable resistor to
set the voltage.
Single Output Voltage Trim Tables
RP15-, RP20-, RP30-, RP40-, RP60- xx3.3S
(For RP15-SA/SAW and RP15-SO/SOW see next page)
Trim up
Vout =
RU =
1
3,333
57.93
2
3,366
26.16
3
3,399
15.58
4
3,432
10.28
5
3,465
7.11
6
3,498
4.99
7
3,531
3.48
8
3,564
2.34
9
3,597
1.46
10
3,63
0.75
%
Volts
KOhms
Trim down
Vout =
RD =
1
3,267
69.47
2
3,234
31.23
3
3,201
18.49
4
3,168
12.12
5
3,135
8.29
6
3,102
5.74
7
3,069
3.92
8
3,036
2.56
9
3,003
1.50
10
2,97
0.65
%
Volts
KOhms
RP15-, RP20-, RP30-, RP40-, RP60- xx05S
(For RP15-SA/SAW and RP15-SO/SOW see next page)
Trim up
Vout =
RU =
1
5,05
36.57
2
5,1
16.58
3
5,15
9.92
4
5,2
6.58
5
5,25
4.59
6
5,3
3.25
7
5,35
2.30
8
5,4
1.59
9
5,45
1.03
10
5,5
0.59
%
Volts
KOhms
Trim down
Vout =
RD =
1
4,95
45.53
2
4,9
20.61
3
4,85
12.31
4
4,8
8.15
5
4,75
5.66
6
4,7
4.00
7
4,65
2.81
8
4,6
1.92
9
4,55
1.23
10
4,5
0.68
%
Volts
KOhms
RP15-, RP20-, RP30-, RP40- ,RP60-xx12S
(For RP15-SA/SAW and RP15-SO/SOW see next page)
Trim up
Vout =
RU =
1
12,12
367.91
2
12,24
165.95
3
12,36
98.64
4
12,48
64.98
5
12,6
44.78
6
12,72
31.32
7
12,84
21.70
8
12,96
14.49
9
13,08
8.88
10
13,2
4.39
%
Volts
KOhms
Trim down
Vout =
RD =
1
11,88
460.99
2
11,76
207.95
3
11,64
123.60
4
11,52
81.42
5
11,4
56.12
6
11,28
39.25
7
11,16
27.20
8
11,04
18.16
9
10,92
11.13
10
10,8
5.51
%
Volts
KOhms
RP15-, RP20-, RP30-, RP40-, RP60- xx15S
(For RP15-SA/SAW and RP15-SO/SOW see next page)
Trim up
Vout =
RU =
1
15,15
404.18
2
15,3
180.59
3
15,45
106.06
4
15,6
68.80
5
15,75
46.44
6
15,9
31.53
7
16,05
20.88
8
16,2
12.90
9
16,35
6.69
10
16,5
1.72
%
Volts
KOhms
Trim down
Vout =
RD =
1
14,85
499.82
2
14,7
223.41
3
14,55
131.27
4
14,4
85.20
5
14,25
57.56
6
14,1
39.14
7
13,95
25.97
8
13,8
16.10
9
13,65
8.42
10
13,5
2.282
%
Volts
KOhms
www.recom-international.com
2014
A-39
Powerline DC-DC Application Notes
Trim Tables
RP15-S_DA, RP15 S:DAW Output Voltage Trim Tables
RP15-xx3.3SA, RP15-xx3.3SAW, RP15-xx3.3SO, RP15-xx3.3SOW
Trim up
Vout =
RU =
1
3,333
385.07
2
3,366
191.51
3
3,399
126.99
4
3,432
94.73
5
3,465
75.37
6
3,498
62.47
7
3,531
53.25
8
3,564
46.34
9
3,597
40.96
10
3,63
36.66
%
Volts
KOhms
Trim down
Vout =
RD =
1
3,267
116.72
2
3,234
54.78
3
3,201
34.13
4
3,168
23.81
5
3,135
17.62
6
3,102
13.49
7
3,069
10.54
8
3,036
8.32
9
3,003
6.60
10
2,97
5.23
%
Volts
KOhms
RP15-xx05SA, RP15-xx05SAW, RP15-xx05SO, RP15-xx05SOW
Trim up
Vout =
RU =
1
5,05
253.45
2
5,1
125.70
3
5,15
83.12
4
5,2
61.82
5
5,25
49.05
6
5,3
40.53
7
5,35
34.45
8
5,4
29.89
9
5,45
26.34
10
5,5
23.50
%
Volts
KOhms
Trim down
Vout =
RD =
1
4,95
248.34
2
4,9
120.59
3
4,85
78.01
4
4,8
56.71
5
4,75
43.94
6
4,7
35.42
7
4,65
29.34
8
4,6
24.78
9
4,55
21.23
10
4,5
18.39
%
Volts
KOhms
RP15-xx12SA, RP15-xx12SAW, RP15-xx12SO, RP15-xx12SOW
Trim up
Vout =
RU =
1
12,12
203.22
2
12,24
99.06
3
12,36
64.33
4
12,48
46.97
5
12,6
36.56
6
12,72
29.61
7
12,84
24.65
8
12,96
20.93
9
13,08
18.04
10
13,2
15.72
%
Volts
KOhms
Trim down
Vout =
RD =
1
11,88
776.56
2
11,76
380.72
3
11,64
248.78
4
11,52
182.81
5
11,4
143.22
6
11,28
116.83
7
11,16
97.98
8
11,04
83.85
9
10,92
72.85
10
10,8
64.06
%
Volts
KOhms
RP15-xx15SA, RP15-xx15SAW, RP15-xx15SO, RP15-xx15SOW
Trim up
Vout =
RU =
1
15,15
161.56
2
15,3
78.22
3
15,45
50.45
4
15,6
36.56
5
15,75
28.22
6
15,9
22.67
7
16,05
18.70
8
16,2
15.72
9
16,35
13.41
10
16,5
11.56
%
Volts
KOhms
Trim down
Vout =
RD =
1
14,85
818.22
2
14,7
401.56
3
14,55
262.67
4
14,4
193.22
5
14,25
151.56
6
14,1
123.78
7
13,95
103.94
8
13,8
89.06
9
13,65
77.48
10
13,5
68.22
%
Volts
KOhms
A-40
2014
www.recom-international.com
Powerline DC-DC Application Notes
Trim Tables
Dual Output Voltage Trim Tables
RP15-, RP20, RP30-, RP40- xx12D
Trim up
Vout =
RU =
1
24,24
218.21
2
24,48
98.10
3
24,72
58.07
4
24,96
38.05
5
25,2
26.04
6
25,44
18.03
7
25,68
12.32
8
25,92
8.03
9
26,16
4.69
10
26,4
2.02
%
Volts
KOhms
Trim down
Vout =
RD =
1
23,76
273.44
2
23,52
123.02
3
23,28
72.87
4
23,04
47.80
5
22,8
32.76
6
22,56
22.73
7
22,32
15.57
8
22,08
10.20
9
21,84
6.02
10
21,6
2.67
%
Volts
KOhms
RP15-, RP20-, RP30-, RP40- xx15D
Trim up
Vout =
RU =
1
30,3
268.29
2
30,6
120.64
3
30,9
71.43
4
31,2
46.82
5
31,5
32.06
6
31,8
22.21
7
32,1
15.1
8
32,4
9.91
9
32,7
5.81
10
33
2.53
%
Volts
KOhms
Trim down
Vout =
RD =
1
29,7
337.71
2
29,4
152.02
3
29,1
90.13
4
28,8
59.18
5
28,5
40.61
6
28,2
28.23
7
27,9
19.39
8
27,6
12.76
9
27,3
7.60
10
27
3.47
%
Volts
KOhms
www.recom-international.com
2014
A-41
Powerline DC-DC Application Notes
Undervoltage Lockout
Undervoltage Lockout
At low input voltages, the input currents
can exceed the rating of the converter.
Therefore, converters featuring under-
voltage lockout will automitically shut
down if the input voltage is too low. As
the input voltage rises, they will restart.
Undervoltage Lockout Tables
Converter Series
Nominal Input Voltage
Switch ON
input voltage
Switch OFF
input voltage
RP08-S_DAW
24V (9~36VDC)
48V (18~75VDC)
9VDC
18VDC
8VDC
16VDC
RP12-S_DA
12V (9~18VDC)
24V (18~36VDC)
48V (36~75VDC)
9VDC
18VDC
36VDC
8VDC
16VDC
33VDC
RP12-S_DAW
24V (9~36VDC)
48V (18~75VDC)
9VDC
18VDC
8VDC
16VDC
RP15-S_DA, RP15-S_DO
12V (9~18VDC)
24V (18~36VDC)
48V (36~75VDC)
9VDC
17VDC
33VDC
8VDC
14.5VDC
30.5VDC
RP15-S_DAW, RP15-S_DOW
24V (9~36VDC)
48V (18~75VDC)
9VDC
18VDC
8VDC
16VDC
RP15-S_DFW
24V (9~36VDC)
48V (18~75VDC)
9VDC
18VDC
7.5VDC
15VDC
RP20-S_DFW
24V (9~36VDC)
48V (18~75VDC)
9VDC
18VDC
7.5VDC
15VDC
RP30-S_DE
12V (9~18VDC)
24V (18~36VDC)
48V (36~75VDC)
9VDC
17.8VDC
36VDC
8VDC
16VDC
33VDC
RP30-S_DEW
24V (10~40VDC)
48V (18~75VDC)
10VDC
18VDC
8VDC
16VDC
RP40-S_D_TG
12V (9~18VDC)
24V (18~36VDC)
48V (36~75VDC)
9VDC
17.8VDC
36VDC
8VDC
16VDC
34VDC
RP30-S_DGW
24V (9~36VDC)
48V (18~75VDC)
9VDC
18VDC
8VDC
16VDC
RP60-SG
24V (18~36VDC)
48V (36~75VDC)
17VDC
34VDC
15VDC
32VDC
A-42
2014
www.recom-international.com
DC-DC Converter Applications
Thermal ManagementThe Laws of Thermodynamics
Thermal ManagementThermal Impedance
Smaller, more powerful, better performance
…are the buzzwords in the area of DC/DC
module power supplies. Good thermal
management of the heat generated has
become an important part of the designprocess. But what needs to be done?
The Thermal Impedance is a measure of how
effectively heat can flow from inside the converter to its surroundings. It is measured in
°C/Watt. It is possible to further lower the
thermal resistance to ambient by fitting an
external heat sink as this increases the surface
area from which heat can be transferred to the
surrounding air. The thermal impedance can
also be lowered by blowing air across the
converter as moving air can transfer more heat
away from the converter as stationary air.
An indisputable fact is that the efficiency of any
energy conversion process is always less than
100%. This means that a part of the energy
being converted goes astray as heat and that
ultimately this waste heat must be removed.
The laws of thermodynamics state that heat
energy can only flow from a warmer to a
colder environment. So, for DC/DC converters,
this means that if the internal heat is to be
dissipated out of the module, that the ambient
temperature must always be lower than the
maximum allowable internal temperature. The
larger this difference, the more effectively
waste heat can flow out of the converter.
But which temperature specifications in the
datasheets are to be consulted for the thermal
calculations? RECOM declares two values in
its datasheets, Operating Temperature Range
(with or without derating) and the Maximum
Case Temperature. Some manufacturers even
claim that these two values are the same.
The case (surface) temperature of DC/DC
modules are typically given as around +100°C.
This value appears at first to be very high;
however this figure includes not only the selfwarming through internal losses but also the
ambient temperature itself.
Remember: The smaller the difference
between case surface and ambient, so the
smaller the amount of heat that can be lost to
the surroundings. If a converter has high
internal dissipation, then it will be more
affected by a small temperature difference
than a converter with low internal dissipation.
The internal losses occur mainly through
switching losses in the transistors, rectification
losses, core losses in the transformer and
resistive losses in the windings and tracks. The
maximum allowable internal temperature is
determined by either the curie temperature of
the transformer core material, the maximum
junction temperature of the switching
transistors or rectification diodes or the
maximum operating temperature of the
capacitors: whichever is the lowest.
www.recom-international.com
Recom datasheets always show the thermal
impedance without a heatsink and with
natural convection (still air).
The datasheets also state the minimum and
maximum ambient operating temperature
rather than just the maximum case
temperature because this is easiest for the end
user to measure and to monitor. The advantage
is that true ambient temperature can be measured in the actual application and it need not
be calculated theoretically, plus the results are
valid for both sealed and vented constructions
with a through-flow of cooling air.
Nevertheless, the maximum case temperature
is useful to decide on a suitably dimensioned
heat sink so that the maximum case
temperature is not exceeded at the maximum
ambient temperature.
The internal losses and thermal resistances
can also be derived mathematically.
For the calculations, Ohm’s Law of R=V/I can
be modified so that R becomes thermal resistance, V becomes temperature and I becomes
power dissipation. The following equations can
thus be derived:
where
R THcase-ambient = Thermal impedance
(from the case to the ambient surroundings)
T case =Case temperature
T ambient=Environment temperature
P dissipation =Internal losses
P in =Input power
P out =Output power
η(oper) =efficiency under the given operating
conditions
2014
With help of the above formulae, the maximum
allowable ambient temperature for a given set
of operating conditions can be calculated - but
it is important to remember that efficiency is
dependent on both the output load and the
input voltage.
The formulae also demonstrate that case
temperature is not the same as operating
temperature, as is so often falsely claimed.
A practical example:
Take the RP30-4805SE with 80% load:
What is the maximum operating temp?
From the datasheet text and graphs, the
following information can be found:
R THcase-ambient = 10°C/W
T case = 100°C maximum
T ambient=unknown
P dissipation must be calculated from:
P out = 30 x 80% = 24W
η(oper) = 90% (from Eff vs Load Graph)
P diss. = 24/0.9 -24 = 2.66 Watts.
Thus
10W/°C = (100 - T amb) / 2.66W
and T amb max. = 73.4°C
At 100% load, this figure reduces to 64.4°C
At 100% load and over the full input voltage
range, this figure reduces further to 59.1°C
If the thermal dissipation calculations reveal
that the DC/DC Module will overheat at the
desired ambient operating temperature, then
there are still a number of options available to
reach a solution.
One option is to derate the converter, i.e, use a
higher power converter running at less than full
load. The derating diagrams in the datasheets
essentially define the maximum load at any
given temperature within the operating
temperature range. The derating curves are in
reality not so linear as they are declared in
most datasheets. However, reliable
manufacturers will always err on the safe side
so that the values given can be safely relied on
in practice.
If the converter has a plastic case, then the
next largest case size with the same power
rating could be chosen to increase the
available surface area. However, care must be
taken not to compromise on efficiency
otherwise no net gain will be made.
A-43
DC-DC Converter Applications
If the converter has a metal case, then adding
a heat sink is can be very effective, particularly
in conjunction with a forced-air cooling system.
If a heat sink is used with fan cooling, then the
thermal resistance equation becomes:
RTHcase-ambient = RTHcase-heatsink + RTHheatsink-ambient
where
RTHcase-ambient =Thermal impedance
(from the case to the ambient surroundings)
RTHcase-heatsink =Thermal impedance
(from the case to the heat sink)
RTHheatsink-ambient =Thermal impedance
(from the heat sink to ambient)
The value of RTH heatsink-ambient includes
the thermal resistance of the heat sink as well
as the thermal resistance of any thermally
conductive paste or silicon pads used for a
better thermal contact to the case. If these heat
transfer aids are not applied, then a value of
approximately 0.2 K/W must be added to the
thermal resistance of the heat sink alone.
When establishing of the value of RTH
heatsink-ambient it is also necessary to know
how much air is being blown across the heat
sink fins. These values are most often given in
lfm (linear feet per minute) and declared by the
fan manufacturer. The conversion to m/s is
100lfm = 0.5 m/s.
Heatsink mounted on case
without thermal conductivity paste
RTH case-heatsink = ca. 1…2 °C/W
Heatsink mounted on case
with thermal conductivity paste
RTH case-heatsink = ca. 0,5…1 °C/W
Heatsink mounted on case
with thermal conductivity paste
and electrical isolation film
RTH case-heatsink = ca. 1…1,5 °C/W
Therefore, If a heatsink is mounted on the
converter, it’s thermal resistance has to be at
least:
RTHcase-ambient = RTHcase-heatsink + RTHheatsink-ambient =
6.1°C/W - 1°C/W = 5.1°C/W
If however, the results of your calculations or
measurements are border-line, then the issue
must be examined in more depth. So, for
example, there is a difference in thermal
performance between vertically and
horizontally mounted modules, between static
air and freely convecting air and with air at low
atmospheric pressures.
1.0
NATURAL CONVECTION
EFFECTIVENESS
Thermal ManagementHeat Sinking
0.8
0.6
0.4
0.2
0.0
0
2000
4000
8000
20000
40000
80000
ALTITUDE (FT)
Calculation of heatsinks size:
Example: RP30-2405SEW starts derating
without heatsink at +65°C but the desired
operation is 30W at +75°C so the size of
the heatsink has to be calculated.
Pout = 30W
Efficiency = 88% max.
Pd =
Pout - Pout
Efficiency
= 30W - 30W = 4.1W
88%
Tcase = 100°C (max. allowed case temperature)
Tambient = 75°C
RTHcase-ambient = Tcase-Tambient = 100°C-75°C
PD
4.1W
=6.1°C/W
So it has to be ensured that the thermal
resistance between case and ambient is
6,1°C/W max.
When mounting a heatsink on a case there is
a thermal resistance RTH case-heatsink between
case and heatsink which can be reduced by
using thermal conductivity paste but cannot be
eliminated totally.
A-44
2014
www.recom-international.com
Powerline DC-DC Application Notes
Heat Sinks available from Recom
7G-0047C (12°C/W)- includes double-sided adhesive pad and clips
7G-0020C (9.5°C/W) - includes double-sided adhesive pad and clips
A : A ( 5 : 1mm)
3.2 ±0.1
49.80 ±0.2
1.30
R 0.65
24.20±0.2
12.00 ±0.2
A :A
R2
1.30
1.40
1.2 ±0.1
1.30
1.40
2.00
12.00 ±0.2
5.60 ±0.1
1.70 ±0.1
www.recom-international.com
2014
A-45
Powerline DC-DC Application Notes
Heat Sinks available from Recom
7G-0011C (8.24°C/W)- includes double-sided adhesive pad and clips
A : A ( 5 : 1mm)
50.00 ±0.2
R 0.65
37.40±0.2
15.00 ±0.2
1.30
A :A
1.40
1.30
3.00 ±0.1
1.00
2.00
27.00 ±0.2
5.60 ±0.1
1.70 ±0.1
7G-0026C (7.8°C/W)- includes double-sided adhesive pad and clips
3.2 ±0.1
49.80 ±0.2
A : A ( 5 : 1mm)
1.30
49.80 ±0.2
12.00 ±0.2
1.30
1.40
A :A
1.30
1.2 ±0.1
12.00 ±0.2
1.40
1.30
R 0.65
5.60 ±0.1
1.70 ±0.1
A-46
2014
www.recom-international.com
AC/DC Application Notes
Input Fuse
+Vout
L
Live
Time Delay
Fuse
Neutral
AC/DC
Converter
N
- Vout
L
+Vout
Time Delay
Fuses
AC
INPUT
AC/DC
Converter
Adjustable
load
Adjustable
load
- Vout
N
Note: An input fuse is recommended for
safety and protection.
A time-delay or slo-blo fuse should be
fitted.
If the AC connector is not-polarised, then
fuses can be fitted to both inputs
Recommended Fuse Ratings
<40W 1.5Amp
40W
2 Amp
60W
3 Amp
Earthing
+Vout
L
Live
Time Delay
Fuse
Neutral
Earth
AC/DC
N Converter
Adjustable
load
- Vout
FG
Optional Link
Note: If the converter has a ground pin
(FG), then it must be earthed to a safety
ground point.
Use thicker,shorter cables to ensure a
good connection as this will also reduce
the EMC interference.
-Vout can be also connected to FG to reference the output to Ground.
External Filter
L
Live
Neutral
Time Delay
Fuse
Line
Filter
Earth
www.recom-international.com
AC/DC
N Converter
FG
Note: The RECOM RAC series contain a
built-in line filter to meet EN 55022 Class
B Conducted Emissions.
2014
+Vout
Adjustable
load
- Vout
If additional filtering is required, then an
external line filter module can be fitted.
The cabling between the external filter
and the converter should be kept as
short as possible and a central star-earth
wiring should be used.
A-47
AC/DC Application Notes
Combining Converters
L
DC
-in Parallel
AC
DC
Note: AC/DC converters can be
paralleled to increase the output voltage
or to make a hot-swap circuit.
The inputs of two AC/DC converters cannot be wired in series to increase the
input voltage range.
However, single phase AC/DC converters
can be used with three phase supplies if
the input is connected via diodes.
AC
N
L
DC
AC
DC
AC
N
+Vo
0V
+Vo
2Vo
0V
+Vo
0V
+Vo
Vo
0V
Combining Converters
-in Series
Neutral
Note: A DC/DC converter or switching
regulator can be powered from the
output of an AC/DC converter to add an
auxilliary output or negative rail.
+Vout
L
Live
Time Delay
Fuse
Earth
Live
Neutral
Time Delay
Fuse
Earth
AC/DC
N Converter
FG
0V
L
+Vout
AC/DC
N Converter
FG
Aux.
load
R-78xx
DC
Main
load
+Vo
Main
load
DC
0V
-Vout
DC Inputs
Note: All AC/DC converters will also work
with DC inputs.
Check the individual datasheets for the
DC input voltage ranges.
L
200VDC
Time Delay
Fuse
AC/DC
Converter
N
A-48
2014
+Vout
Adjustable
load
- Vout
www.recom-international.com
POWERLINE PLUS - CONTENTS
The POWERLINE PLUS uses ICE Technology. A combination of techniques
to minimise internal heat dissipation and maximise the heat transfer to
ambient to create a new converter series which offers high end performance
at a price which is significantly lower than conventional specialist converters.
RECOM - Green high-efficiency power solutions. SAVE ENERGY. NOW.
Introduction
The RPP series 2:1 and 4:1 input range DC/DC converters are ideal for high end industrial applications and COTS (Commercial Off-The-Shelf) Military applications, where a high ambient operating temperature converter is required.
The RPR series are specifically tailored to the requirements of Railway applications. These converters work under extreme operating conditions and are designed for input voltages up to 160VDC.
Both converters series feature ICE Technology, a revolutionary method of extending the temperature range without increasing
the converter dimensions over standard converters. The built-in aluminium heat sink ensures optimum heat transfer to ambient.
Although the case size is compact, the RPP series contain a built-in EN55022 Class B / FCC Level B filter and the RPR series
contains a built-in EN50121-3-2 Class A filter without the need for any external components.
All converters are fully protected with undervoltage lockout protection, overload, overcurrent and overvoltage protection, short circuit current limiting and overtemperature shutdown.
In addition, the converters have a quiescent current that is an order of magnitude lower than equivalent power converters.
DC/DC Converters with ICE Technology
Series
Power
[W]
Isolation
[kVDC]
RPP20
20
9-18, 18-36, 36-75
RPP20 (W)
20
9-36, 18-75
RPR20
20
12-36, 25-75, 40-160
RPP30
30
9-18, 18-36, 36-75
RPP30 (W)
30
10-40, 18-75
RPR30
30
RPP40
40
10-40, 18-75
RPP40 (W)
40
10-40, 18-75
RPR40
40
12-36, 25-75, 40-160
RPP50
50
18-36, 36-75
3.3, 5, 12, 15, 24
Single
RPR50
50
12-36, 25-75, 40-160
3.3, 5, (+/-)12, (+/-)15, (+/-)24
Single & Dual
2
Input Voltages
[VDC]
Output Voltages
[VDC]
3.3
5
(+/-)12
(+/-)15
(+/-) 24
12-36, 25-75, 40-160
Case Options
Ribbed
Flat
Baseplate
Outputs
Single
Dual
RPR-Series for Railway Applications
www.recom-international.com
2014
A-49
POWERLINE+ Application Notes
DC/DC-Converter
ICE
Technology
ICE Technology
I.C.E Technology
ICE (Innovation in Converter Excellence)
Technology uses a combination of techniques
to minimise internal heat dissipation and
maximise the heat transfer to ambient to
create a new converter series which offers high
end performance at a price which is significantly lower than conventional specialist converters.
The exact details of this technology must
remain secret, but the following brief resume
describes the main features of this
technological breakthrough:
Minimising internal heat dissipation
The difference between the input power and
the output power is the internal power
dissipation which generates heat within the
converter.
If the converter is inefficient at converting
power, then adding external heat sinks, baseplates or fans are remedies that cure the
symptoms rather than address the illness.
First and foremost, the converter must have the
highest possible efficiency over the entire input
voltage range and load conditions. Most power
converters are designed to be most efficient at
25°C, full load and nominal input voltage and
thus offer a compromise performance when
lightly loaded or operated at the maximum
ambient temperature.
ICE Technology uses state-of-the-art
techniques to improve power convertion
efficiency by approximately 2% compared to
standard converters. A two per cent improvement may not sound much, but the difference
between a converter with 88% efficiency and
one with 90% efficiency is a 17% reduction in
the dissipated power. In addition, when lightly
loaded, the converters enter a power saving
mode and draw only a few milliamps from the
supply.
Maximising heat transfer
The rate of heat transfer between a hot body
and its cooler surroundings is given by
Fourier’s Law: q=-k.ΔT
where q = rate of heat transfer
k = thermal conductivity
and ΔT = temperature difference
If k can be made larger, then the rate of heat
transfer can still match or exceed the rate of
heat generation at lower temperature
differences ΔT and the converter will have an
extended operating temperature range.
A-50
Techniques to improve thermal
conductivity
ICE Technology splits the thermal conductivity
problem into two areas and attacks each area
seperately using different techniques.
Electromagnetic Compatibility
Firstly, the internal heat transfer to the case is
maximised by a combination of novel
converter construction and clever thermal
design.
Although high temperature performance is a
significant feature of ICE Technology design, it
does not end there.
ICE converters use a construction where the
hottest components (the switching FET, the
transformer and the synchronous rectification
FETs) are placed closest to the case wall. This
method of construction makes the
manufacture of the converter more difficult, but
this lack of compromise reduces greatly the
internal thermal impedance.
ICE Technology also addresses the need for
electromagnetic compatibility by incorporating
a built-in EN55022 Class B grade filter inside
the converter. The converter has been designed from the ground up to meet EMC requirements rather than a conventional design
process where first the converter is optimised
for performance and then an external filter is
added to combat the conducted interference.
Secondly, the rate of transfer of heat to the
surroundings is improved by a novel case
construction which incorporates a built-in heat
sink. The case is also made from thick aircraft
grade aluminium rather than thin nickel-plated
copper to provide a better thermal junction
between the case and the high thermal
conductivity silicone potting material used
inside the converter.
By including the filter on the main PCB of the
converter, the track path lengths and
impedances between the filter and the noisegenerating components are reduced to the
minimum and consequently smaller value
filter components can be used that fit into the
compact case dimensions of the Powerline+
converters without compromising on filter
performance.
Maximising high
performance
Safety and Protection
temperature
The final technique used in the construction of
ICE Technology converters is to use high
temperature internal components. The
maximum operating temperature of a
converter is dependent on the lowest
maximum permissible operating temperature
of any the components used. If the capacitors
are rated up to +85°C and the FETs are rated
at +160°C, then the limiting factor is the capacitor temperature of +85°C.
The temperature of the ferrite core used in the
transformer is also an important limiting
factor. If the transformer core temperature
exceeds the Curie temperature of the ferrite,
then the transformer rapidly loses
performance.
ICE Technology converter uses high
temperature grade components to permit a
case temperature of +120°C maximum. This
allows operation at up to +85°C ambient
without the need for fans to blow air over the
converter.
2014
ICE Technology converters are fully protected
from output short circuits, overload, output
over-voltage and over-temperature. In addition,
they feature under-voltage lockout that will
automatically disable the converter if the input
voltage falls below the minimum level.
The output is current limited which means that
temporary overloads can occur without the
converter shutting down. When overloaded, the
output voltage will decrease to keep the
maximum power constant. For the 40W and
50W converters, if the overload is too high, the
converter will go into hiccup short circuit
protection mode. In this mode, the converter
will attempt to reconnect power every 10-20
milliseconds.
Output overvoltage protection is monitored by
a separate and independent feedback circuit
and an internal thermistor sensor is used to
protect the converter against overheating.
www.recom-international.com
POWERLINE+ Application Notes
Trim Tables
DC/DC-Converter
Powerline Plus Output Trim Tables
Single output Powerline Plus converters
offer the feature of trimming the output
voltage over a certain range around the
nominal value by using external trim
resistors.
No general equation can be given for
calculating the trim resistors, but the
Output Voltage Trimming:
following trimtables give typical values for
chosing these trimming resistors.
If voltages between the given trim points
are required, extrapolate between the two
nearest given values to work out the
resistor required or use a variable resistor
to set the output voltage.
RPP/RPRxx-xx3.3S (all types)
Trim up
Vout =
RU =
1
3,333
72.8
2
3,366
34.4
3
3,399
21.2
4
3,432
14.4
5
3,465
9.9
6
3,498
7.2
7
3,531
5.3
8
3,564
3.88
9
3,597
2.74
10
3,63
1.84
%
Volts
KOhms
Trim down
Vout =
RD =
1
3,267
101.3
2
3,234
36.2
3
3,201
21.0
4
3,168
13.65
5
3,135
9.2
6
3,102
6.0
7
3,069
4.12
8
3,036
2.56
9
3,003
1.34
10
2,97
0.87
%
Volts
KOhms
RPP/RPRxx-xx05S (all types)
Trim up
Vout =
RU =
1
5,05
109.7
2
5,1
51
3
5,15
31.2
4
5,2
20.3
5
5,25
14.2
6
5,3
9.87
7
5,35
7.1
8
5,4
5.0
9
5,45
3.38
10
5,5
2.08
%
Volts
KOhms
Trim down
Vout =
RD =
1
4,95
127.6
2
4,9
55.8
3
4,85
33.0
4
4,8
20.2
5
4,75
14.2
6
4,7
9.46
7
4,65
5.97
8
4,6
3.6
9
4,55
1.77
10
4,5
0.28
%
Volts
KOhms
RPP/RPRxx-xx12S (all types)
Trim up
Vout =
RU =
1
12,12
270
2
12,24
120
3
12,36
70
4
12,48
45.2
5
12,6
30.1
6
12,72
19.8
7
12,84
12.8
8
12,96
7.52
9
13,08
3.31
10
13,2
0
%
Volts
KOhms
Trim down
Vout =
RD =
1
11,88
270
2
11,76
120
3
11,64
70
4
11,52
45.2
5
11,4
30.1
6
11,28
19.8
7
11,16
12.8
8
11,04
7.52
9
10,92
3.31
10
10,8
0
%
Volts
KOhms
RPP/RPRxx-xx15S (all types)
Trim up
Vout =
RU =
1
15,15
337
2
15,3
150
3
15,45
87
4
15,6
56.2
5
15,75
37.5
6
15,9
24.7
7
16,05
16
8
16,2
9.4
9
16,35
4.16
10
16,5
0
%
Volts
KOhms
Trim down
Vout =
RD =
1
14,85
337
2
14,7
150
3
14,55
87
4
14,4
56.2
5
14,25
37.5
6
14,1
24.7
7
13,95
16
8
13,8
9.4
9
13,65
4.16
10
13,5
0
%
Volts
KOhms
www.recom-international.com
2014
A-51
Block
Diagrams
POWERLINE+ Application Notes
DC/DC-Converter
Powerline Plus Output Trim Tables
RPP/RPRxx-xx24S (all types)
Trim up
Vout =
RU =
1
24,24
270
2
24,48
120
3
24,72
70
4
24,96
45.2
5
25,20
30.1
6
25,44
19.8
7
24,68
12.8
8
25,92
7.52
9
26,16
3.31
10
26,4
0
%
Volts
KOhms
Trim down
Vout =
RD =
1
23,76
270
2
23,52
120
3
23,28
70
4
23,04
45.2
5
22,80
30.1
6
22,56
19.8
7
22,32
12.8
8
22,08
7.52
9
21,84
3.31
10
21,6
0
%
Volts
KOhms
Block Diagrams
Single Output - 3.3V and 5V Outputs
+Vin
+Vout
Switch
Control
Com
-Vin
ON/OFF
Control
Overtemp.
Sensor
PWM
Controller
Isolation
Overvoltage
Sensor
Isolation
Reference
& Error AMP
Trim
Single Output - 12V, 15V and 24V Outputs
+Vin
+Vout
Com
-Vin
ON/OFF
Control
A-52
Overtemp.
Sensor
PWM
Controller
Isolation
Overvoltage
Sensor
Isolation
Reference
& Error AMP
2014
Trim
www.recom-international.com
Block
Diagrams
POWERLINE+ Application Notes
DC/DC-Converter
Block Diagrams
Dual Output
+Vout
Com
+Vin
-Vout
-Vin
ON/OFF
Control
Overtemp.
Sensor
www.recom-international.com
PWM
Controller
Isolation
Overvoltage
Sensor
Isolation
Reference
& Error AMP
2014
A-53
Application Notes
DC/DC Block Diagrams
Unregulated Single Output
RM, RL , RNM, RN, RO, RE, ROM,
R1S, RB-xxxxS, RA-xxxxS, RBMxxxxS, RK, RP-xxxxS, RxxPxxS,
RxxP2xxS, R2S, RI, REZ, RKZxxxxS, RV-xxxxS, RGZ, R0.25S
+Vin
+Vout
Oscillator
-Vout
-Vin
Unregulated Dual Output
RQD, R1D, RB-xxxxD, RA-xxxxD,
RBM-xxxxD, RH, RP-xxxxD,
RxxPxxD, RxxP2xxD, R2D, RCxxxxD, RD-xxxxD, RKZ-xxxxD, RVxxxxD, RJZ, R0.25S
+Vin
+Vout
Oscillator
Com
-Vout
-Vin
Unregulated Dual Isolated Output
RU, RUZ, R1DA
+Vin
+Vout1
-Vout1
Oscillator
+Vout2
-Vout2
-Vin
Post-Regulated Single Output
R1Z, R0.5Z, RY-xxxxS, RY-xxxxSCP, REC3-xxxxSR/H1
+Vin
Reg
+Vout
Oscillator
-Vout
-Vin
Post-Regulated Dual Output
RY-xxxxD, REC3-xxxxDR/H1
+Vin
Reg
Oscillator
Com
Reg
-Vin
A-54
+Vout
2014
-Vout
www.recom-international.com
Application Notes
DC/DC Block Diagrams
Regulated Single Output
RSO, RS, RS3, RW-xxxxS, REC3-xxxxSRW(Z)/H*, REC5-xxxxSRW(Z)/H*, REC7.5-xxxxSRW/AM/H*, REC08-xxxxSRW, REC10-xxxxSRW, REC15-xxxxSRW,
RP08-xxxxSA, RP08-xxxxSAW, RP10-xxxxSE, RP10-xxxxSEW, RP12-xxxxSA, RP12-xxxxSAW, RP15-xxxxSO, RP15-xxxxSOW, RP15-xxxxSA, RP15-xxxxSAW,
RP15-xxxxSF, RP15-xxxxSFW, RP20-xxxxSA, RP20-xxxxSAW, RP20-xxxxSF, RP20-xxxxSFW
+Vin
Noise
Filter
+Vout
-Vout
-Vin
Oscillator &
Controller
Isolation
Reference
& Error AMP
Regulated Dual Output
RSO-xxxxD, RS-xxxxD, RW-xxxxD, REC3-xxxxDRW(Z)/H*, REC5-xxxxDRW(Z)/H*, REC7.5-xxxxDRW/AM/H*, REC08-xxxxDRW, REC10-xxxxDRW, REC15xxxxDRW, RP08-xxxxDA, RP08-xxxxDAW, RP10-xxxxDE, RP10-xxxxDEW, RP12-xxxxDA, RP12-xxxxDAW, RP15-xxxxDF, RP15-xxxxDFW, RP15-xxxxDA, RP15xxxxDAW, RP20-xxxxDA, RP20-xxxxDAW, RP20-xxxxDF, RP20-xxxxDFW, RP30-xxxxDE, RP30-xxxxDEW, RP40-xxxxDG, RP40-xxxxDGW
+Vin
Noise
Filter
+Vout
Com
-Vout
-Vin
Oscillator &
Controller
www.recom-international.com
Isolation
2014
Reference
& Error AMP
A-55
Application Notes
DC/DC Block Diagrams
Regulated Triple Output
RP40-05xxTG
+Vaux
Com
+Vin
Noise
Filter
-Vaux
+Vout1
-Vout1
-Vin
Oscillator &
Controller
Isolation
Reference
& Error AMP
Regulated Single Output, Synchronous Rectification
RP20-xxxxSF, RP20-xxxxSA, RP20-xxxxSAW, RP30-xxxxSE, RP30-xxxxSEW, RP40-xxxxSG, RP40-xxxxSGW, RP60-xxxxSG
+Vin
+Vout
Switch
Control
Com
-Vin
PWM
Controller
Isolation
Reference
& Error AMP
Trim
ON/OFF
Control
A-56
2014
www.recom-international.com
Application Notes
AC/DC Block Diagrams
RAC05-xxSA, RAC10-xxSA, RAC15-xxSA, RAC20-xxSA, RAC30-xxSA, RAC60-xxSB
+Vout
L
Line Filter
N
Rectifier
-Vout
FG
PWM
Controller
Isolation
Reference
& Error AMP
RAC01-xxSC, RAC02-xxSC, RAC03-xxSC, RAC03-xxSA, RAC04-xxSA, RAC05-xxSB, RAC06-xxSC, RAC10-xxSB, RAC15-xxSB, RAC30-xxSA,
RAC40-xxSA, RAC40-xxSB
L
+Vout
Rectifier
-Vout
N
PWM
Controller
www.recom-international.com
Isolation
2014
Reference
& Error AMP
A-57
Application Notes
AC/DC Block Diagrams
RAC05-xxDA, RAC10-xxDA, RAC15-xxDA, RAC20-xxDA, RAC30-xxDA
L
+Vout
Filter
Rectifier
Com
-Vout
N
FG
Overcurrent
Protection
PWM
Controller
Isolation
Reference
& Error AMP
RAC06-xxDC, RAC15-xxDB, RAC30-xxDA, RAC40-xxDA, RAC40-xxDB
L
+Vout
Filter
Rectifier
-Vout
N
Overcurrent
Protection
A-58
PWM
Controller
Isolation
2014
Reference
& Error AMP
www.recom-international.com
Application Notes
AC/DC Block Diagrams
RAC15-05xxTA, RAC20-05xxTA
+5Vout
+5V Rtn
+Vout
L
N
Line Filter
Com
Rectifier
-Vout
FG
Overcurrent
Protection
PWM
Controller
Isolation
Reference
& Error AMP
RAC15-05xxTB, RAC30-05xxTA, RAC40-05xxTA
+5Vout
+5V Rtn
+Vout
L
Line Filter
Com
Rectifier
-Vout
N
Overcurrent
Protection
www.recom-international.com
PWM
Controller
Isolation
2014
Reference
& Error AMP
A-59
Transport Tubes
No.
Types
1.
RO, RM, RN, RNM, RE, ROM, RB, RBM, RK, RH, RP, RU, RI, RD, RKZ, RUZ, RY,
R-78xx-0.5, R-78xx-1.0, R-78Cxx-1.0, R-78Exx-0.5, R-78Exx-1.0
2.
RS, RSO, RS3
3.
RJZ, RGZ, RW2(B)
4.
RSS, RSD, RZ, R1S, R1D, R1Z, R0.5Z
5.
RTD, RTS, RSZ, R-78Axx-xx SMD, R2S, R2D, R-78AAxx-xx SMD
6.
RV, RW-S, RxxPxx, RxxP2xx, RW2(A)-SMD
7.
R-5xxxPA, R-6xxxP, R-7xxxP, RW-D,
REC3-, REC3.5, REC5-, REC6-, REC7.58.
RP08, RP12, REC8, REC10, RCD-24-xxx
9.
RP15-O, RP15-OW, RP15-A, RP15-AW, REC15
10.
RAC01, RAC02
11.
RP10, RP15, RP20, RP30, RP40
12.
RP08-SMD, REC3-SMD, REC5-SMD, REC7.5-SMD
13.
R-78Bxx-xx, R-78HBxx-xx
14.
R-78Bxx-xxL, R-78HBxx-xxL
15.
R-5xxxDA, R-6xxxD, R-7xxxD
all dimensions in mm
1.
2.
TUBE LENGTH = 520±2.0
A-60
3.
TUBE LENGTH = 520±1.5
2014
TUBE LENGTH = 520±1.0
www.recom-international.com
Transport Tubes
4.
5.
TUBE LENGTH = 530±2.0
6.
TUBE LENGTH = 530±2.0
7.
TUBE LENGTH =530±2.0
8.
TUBE LENGTH = 530±2.0
TUBE LENGTH = 530±2.0
10.
9.
36.8±0.5
18.5±0.5
27.4±0.5
21.7±0.5
TUBE LENGTH = 530±2.0
www.recom-international.com
TUBE LENGTH = 520±1.0
2014
A-61
Transport Tubes
11.
54.0 ± 0.5
50.0 ± 0.5
22.0 ± 0.5
20.0 ± 0.5
7.0 ± 0.5
1.2 ± 0.2
6.0 ± 0.5
10.0 ± 0.5
15.0 ± 0.5
12.
TUBE LENGTH = 254mm ± 2.0
13.
9.3 ± 0.25
0.63 ± 0.15
23.8 ± 0.25
18.5 ± 0.25
4.3 ± 0.25
TUBE LENGTH = 520mm ± 2.0
15.
14.
6.5±0.25
0.7±0.2
17.15±0.25
17.8±0.25
7.62± 0.25
9.2±0.25
0.5± 0.127
5±0.25
11.1±0.25
10.2±0.25
3.3±0.25
18.42±0.25
11.68±0.25
12.32±0.25
TUBE LENGTH = 520mm ± 2.0
A-62
2.41±0.25
TUBE LENGTH = 520mm ± 2.0
2014
www.recom-international.com
Tape and Reel (Suffix -R)
RSS(8)-xxxx & R1S(8)-xxxx tape outline dimensions
13.2
Spocket hole Ø1.50+0.1/-0
Spocket hole tolerance over any 10 pitches ±0.2
0.40 ±0.05
16.00
2.00
4.00
11.4
1.75
7.6
11.5
24.0 ±0.2
RECOM
R1S-0505
xxxx
All dimensions in mm xx.xx ±0.1
1. 10 sprocket hole pitch cumulative tolerance ±0.20
2. All dimensions meet EIA-481-2 requirements
3. Component load per 13" reel : 500 pcs
RECOM
R1S-0505
xxxx
4. The diameter of disc center hole is 13.0mm
www.recom-international.com
RECOM
R1S-0505
xxxx
2014
A-63
Tape and Reel (Suffix -R)
RSD(10)-xxxx, RSS12-xxxx, RSD12-xxxx, R1D(10)-xxxx, R1S12-xxxx, R1D12-xxxx,
& RZ-xxxx tape outline dimensions
17.75
Spocket hole Ø1.50+0.1/-0
Spocket hole tolerance over any 10 pitches ±0.2
0.35 ±0.05
16.00
2.00
4.00
11.4
1.75
7.6
11.5
24.0 ±0.2
RECOM
RSD-0505
xxxx
All dimensions in mm xx.xx ±0.1
RECOM
RSD-0505
xxxx
1. 10 sprocket hole pitch cumulative tolerance ±0.20
2. All dimensions meet EIA-481-2 requirements
3. Component load per 13" reel : 500 pcs
RECOM
RSD-0505
xxxx
4. The diameter of disc center hole is 13.0mm
A-64
2014
www.recom-international.com
Tape and Reel (Suffix -R)
RSZ-xxxx, RTS-xxxx, R2S-xxxx, RTD-xxxx, R2D-xxxx
R-78Axx-xxSMD & R-78AAxx-xxSMD tape outline dimensions
15.5
Spocket hole Ø1.50+0.1/-0
Spocket hole tolerance over any 10 pitches ±0.2
0.5 ±0.05
20.00
2.00
4.00
12.5
1.75
9.9
11.5
24.0 ±0.3
RECOM
RSZ-0505
xxxx
All dimensions in mm xx.xx ±0.1
1. 10 sprocket hole pitch cumulative tolerance ±0.20
2. All dimensions meet EIA-481-2 requirements
3. Component load per 13" reel : 500 pcs
RECOM
RSZ-0505
xxxx
4. The diameter of disc center hole is 13.0mm
www.recom-international.com
RECOM
RSZ-0505
xxxx
2014
A-65