SMD Series Gas Tube Arresters 1. Part Number Code UTC – 4532 – 4 0 1 M – A (1) (2) (3) (4) (5) (1) Band Name . (2) Series Code . (3) DC breakdown voltage (e.g.75V,90V,120V,150V, 200V, 230V, 300V,350V, 400V,420V, 470V,500V,600Vetc.) (4) Tolerance of DC breakdown voltage: M (±20%), N (±30%) (5) Surge Current : (waveform 8/20µS) A : 1KA , B : 2KA , C : 3KA 2. Drawing SMD Series Gas Tube Arresters 3. Electrical Specification Model 401 (M) DC Breakdown Voltage 100v/s 400V 320~480 Impulse Discharge Current 8/20 us A: 1KA 1500A B: 2KA C: 3KA Tolance : (M) = ±20% , (N) = ±30% Impulse Withstanding Voltage Capacity Impulse Spark-over Voltage 1kv/us 10/700 us 6kV = < 600v Insulation Resistance 1GΩ Min (DC 250V) Capacitance (1MHz 1V) 0.5 pF Max. SMD Series Gas Tube Arresters 4. Electrical Rating Item DC Breakdown Test Condition / Description Requirement The voltage measured at a rise time of 100v/s. Voltage The maximum current applying a waveform of 8/20us that can be applied Maximum Impulse across the terminals of the gas tube without causing the gas tube to Discharge Current change more than ±25% from its initial measured DC breakdown voltage. Dwell time between pulses is 3 minutes. Rated RMS value of AC current at 50Hz, 1 sec. 10 times. Intervals: 3min. Alternating DC breakdown voltage may not change more than ±25% from its initial Discharge Current measured DC breakdown voltage. IR > 108 ohms (-20%, +30% for 70 – 90V). Impulse Life The minimum number of impulses of a specified waveform and peak current which a gas tube will conduct without causing the gas tube to Impulse Withstanding change more than ±25% from its initial measured DC breakdown voltage. To meet the Dwell time between pulses is 1-2 minutes. specified value The minimum number of impulses of a specified waveform and peak current which a gas tube will conduct without causing the gas tube to Voltage change more than ±25% from its initial measured DC breakdown voltage. Capacity Dwell time between pulses is 1-2 minutes. The resistance of the gas tube shall be measured each terminal to each Insulation Resistance Capacitance other terminal. DC Breakdown Voltage Measuring Voltage 70-150V 50V 151-600V 100V The capacitance of a gas tube shall be measured each terminal to each other terminal. Test frequency: 1GHz In measurements involving 3-electrode gas tubes, the terminal not being tested shall be connected to a ground plane. SMD Series Gas Tube Arresters Chip GDT Taping unit :mm Item Spec A 3.7±0.20 B 4.7±0.20 D0 Φ1.50±0.10 E 1.75±0.10 F 5.50±0.10 P0 4.0±0.10 P1 8.0±0.10 P2 2.0±0.10 W 12.00±0.30 D P1 0 P2 W F B E P0 A OUTLINE REEL (PCS) PER CARTON (PCS) REEL DIAMETERS (mm) L W H TAPING 2,000 32,000 330 360 360 360 CARTON SIZE(mm) 5. Recommended Soldering Pad And Reflow Profile 5.45mm 240 220 TEMPERATURE( C) 3.5mm MAX260 C 260 200 3 .5 m m 160 175 C 25 C 65 SECONDS TIME ABOVE 217 C 65 SECONDS 120 100 80 60 40 PREHEAT REFLOW 20 0 20 40 60 80 100 120 140160 180 200 220 240 260 TIME (S) T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N P age :1 of9 *CE/2012/A4311A* T he follow ing s am ple(s )w as / w ere s u bm itted and identified by/ on behalfofthe client as : S am p l e D escrip tion S tyl e/Item N o. S am p l e R eceiving D ate Testing P eriod : : : : G A S TU B E 2R S ER IES , 3R S ER IES , S M D S ER IES , 321 6S ER IES , 4532 S ER IES 20 1 2/1 0 /22 20 1 2/1 0 /22 TO 20 1 2/1 0 /29 ============================================================================================ T es t R equ es ted ient, w ith reference to R oH S D irective 20 1 1 /65/EU A nnex II to : A s sp ecifiedby cl determ ine C adm iu m , L ead, M ercu ry, C r(V I), P B B s, P B D Es contents in the su bm itted sam p l e. T es t M ethod : W ith reference to IEC 62321 :20 0 8. T es t R es u lt(s ) ease refer to nextp age(s). : Pl This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 P age :2 of9 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N *CE/2012/A4311A* T es t R es u lt(s ) P A R T N A M EN o.1 P A R T N A M EN o.2 P A R T N A M EN o.3 T es t Item (s ) C adm iu m (C d) L ead(P b) M ercu ry (H g) H exaval entC hrom iu m C r(V I) ： B O DY ： P L A TIN G L A Y ER O F S IL V ER C O L O R ED M ETA L P IN ： B A S EM A TER IA L O F S IL V ER C O L O R ED M ETA L P IN m g/kg W ith reference to IEC 62321 : 20 0 8 andp erform edby IC P -A ES . 2 N o.1 n.d. R es u lt N o.2 --- m g/kg IEC 62321 :20 0 8 ap p l ication of m odifieddigestion by su rface etching andp erform edby IC P A ES . 2 --- n.d. --- m g/kg W ith reference to IEC 62321 : 20 0 8 andp erform edby IC P -A ES . 2 n.d. --- n.d. m g/kg IEC 62321 :20 0 8 ap p l ication of m odifieddigestion by su rface etching andp erform edby IC P A ES . 2 --- 39 --- m g/kg W ith reference to IEC 62321 : 20 0 8 andp erform edby IC P -A ES . 2 n.d. --- n.d. m g/kg IEC 62321 :20 0 8 ap p l ication of m odifieddigestion by su rface etching andp erform edby IC P A ES . 2 --- n.d. --- m g/kg W ith reference to IEC 62321 : 20 0 8 andp erform edby U V -V IS . 2 n.d. --- --- # --- U nit ** M ethod W ith reference to IEC 62321 : 20 0 8 andp erform edby B oil ing w ater extraction M ethod.# M DL N o.3 n.d. N egative N egative This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 P age :3 of9 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N T es t Item (s ) Su m ofPB B s M onobrom obip henyl D ibrom obip henyl Tribrom obip henyl Tetrabrom obip henyl P entabrom obip henyl H exabrom obip henyl H ep tabrom obip henyl O ctabrom obip henyl N onabrom obip henyl D ecabrom obip henyl Su m ofPB D E s M onobrom odip henylether D ibrom odip henylether Tribrom odip henylether Tetrabrom odip henylether P entabrom odip henylether H exabrom odip henylether H ep tabrom odip henylether O ctabrom odip henylether N onabrom odip henylether D ecabrom odip henylether U nit m g/kg M ethod W ith reference to IEC 62321 : 20 0 8 andp erform edby G C /M S . *CE/2012/A4311A* M DL 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 N o.1 n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. n.d. R es u lt N o.2 --------------------------------------------- N o.3 --------------------------------------------- N ote： 1 . m g/kg = p p m ；0 .1 w t% = 1 0 0 0 p p m 2. n.d.= N otD etected 3. M D L = M ethodD etection L im it 4. "-"= N otR egu l ated 5. "---"= N otC ondu cted 6. **= Q u al itative anal ysis (N o U nit) 7. # = a.P ositive m eans the p resence ofC rV I on the testedareas b.N egative m eans the absence ofC rV I on the testedareas The detectedconcentration in boil ing-w ater-extraction sol u tion is eq u alor greater than 0 .0 2 m g/kg w ith 50 cm ² testedareas. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 P age :4 of9 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N N o.1 , 3 *CE/2012/A4311A* 1 ) These sam p l es w ere dissol vedtotal l y by p re-conditioning m ethodaccordingto bel ow fl ow chart. 6+ （C r testm ethodexcl u ded） 2) N am e ofthe p erson w ho m ade m easu rem ent:C l im bgreatYang 3) N am e ofthe p erson in charge ofm easu rem ent:Troy C hang C u tting/ Prep aration C r6＋ S am p l e M easu rem ent Hg Pb、C d A ciddigestion by su itabl e acid dep endedon dif ferentsam p l e m aterial(as bel ow tabl e) (N ote**) M icrow ave digestion w ith H N O 3/H C l /H F A ddap p rop riate am ou nt ofdigestion reagent H eatto ap p rop riate tem p eratu re to extract Fil tration R esidu e S ol u tion 1) A l kal iFu sion 2) H C lto dissol ve IC P -A ES S am p l e M aterial A dddip henyl -carbazide for col or devel op m ent D igestion A cid Steel , cop p er, al u m inu m , sol der A q u a regia, H N O 3, H C l , H F, H 2O G l ass H N O 3/H F G ol d, p l atinu m , p al l adiu m , ceram ic A q u a regia S il ver HN O Pl astic H 2S O 4, H 2O 2, H N O 3, H C l A ddedap p rop riate reagentto total digestion O thers C ool , fil ter digestate throu gh fil ter 2 m easu re the absorbance at540 nm by U V-VIS 3 N ote**：(1 ) For non-m etal l icm aterial , addal kal ine digestion reagentandheatto 90 ~95 ℃. (2) For m etal l icm aterial , addp u re w ater andheatto boil ing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 P age :5 of9 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N N o.2 *CE/2012/A4311A* 1 ) The p l atingl ayer ofsam p l es w ere dissol vedtotal l y by p re-conditioning m ethodaccordingto bel ow fl ow chart.（C r 6+ testm ethodexcl u ded） 2) N am e ofthe p erson w ho m ade m easu rem ent:C l im bgreatYang 3) N am e ofthe p erson in charge ofm easu rem ent:Troy C hang Flow C hart ofStripping m ethod for m etalanalys is P rep aration S am p l e m easu rem ent Pb、C d、H g C r6 ＋ A ddap p rop riate am ou ntofdigestion reagent P rep are su itabl e acidsol u tion H eatto ap p rop riate tem p eratu re to extract P u tsam p l e into acidsol u tion C ool , fil ter digestate throu gh fil ter D issol ve p l ating l ayer A dddip henyl -carbazide for col or devel op m ent S ol u tion m easu re the absorbance at540 nm by U V-V IS IC P -A ES This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 P age :6of9 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N *CE/2012/A4311A* PB B / PB D E analyticalFL OW C H A RT N am e ofthe p erson w ho m ade m easu rem ent:R om an W ong N am e ofthe p erson in charge ofm easu rem ent:Troy C hang Firsttesting p rocess O p tionalscreen p rocess S am p l e C onfirm ation p rocess S am p l e p retreatm ent S creen anal ysis S am p l e extraction/ S oxhl etm ethod C oncentrate/D il u te Extractedsol u tion Fil ter A nal ysis by G C /M S Issu e R ep ort This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N P age :7 of9 *CE/2012/A4311A* *T he tes ted s am ple /part is m arked by an arrow ifit's s how n on the photo.* This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N P age :8 of9 *CE/2012/A4311A* This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group T es t R eport N o.:C E/20 1 2/A 431 1 A D ate :20 1 4/0 1 /1 4 U N IC TR O N TEC H N O L O G IES C O R P O R A TIO N N O .41 S H U EI-KEN G , G U A N -S I, H S IN -C H U 30 648, TA IW A N P age :9 of9 *CE/2012/A4311A* ** EndofR ep ort ** This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Termse-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. SGS Taiwan Ltd. 台灣檢驗科技股份有限公司 33, Wu Chuan Rd., New Taipei Industrial Park, New Taipei City, Taiwan / 新北市新北產業園區五權路33號 t+886 (02)2299 3279 f+886 (02)2299 3237 www.sgs.tw Member of the SGS Group