W25N01GVxxIG/IT

W25N01GVxxIG/IT
3V 1G-BIT
SERIAL SLC NAND FLASH MEMORY WITH
DUAL/QUAD SPI
BUFFER READ & CONTINUOUS READ
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
Table of Contents
1.
GENERAL DESCRIPTIONS............................................................................................................. 6
2.
FEATURES ....................................................................................................................................... 6
3.
PACKAGE TYPES AND PIN CONFIGURATIONS .......................................................................... 7
4.
3.1
Pad Configuration WSON 8x6-mm ...................................................................................... 7
3.2
Pad Description WSON 8x6-mm .......................................................................................... 7
3.3
Ball Configuration TFBGA 8x6-mm (5x5 or 6x4 Ball Array) ................................................. 8
3.4
Ball Description TFBGA 8x6-mm ......................................................................................... 8
PIN DESCRIPTIONS ........................................................................................................................ 9
4.1
Chip Select (/CS) .................................................................................................................. 9
4.2
Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3) .................................... 9
4.3
Write Protect (/WP)............................................................................................................... 9
4.4
HOLD (/HOLD) ..................................................................................................................... 9
4.5
Serial Clock (CLK) ................................................................................................................ 9
5.
BLOCK DIAGRAM .......................................................................................................................... 10
6.
FUNCTIONAL DESCRIPTIONS ..................................................................................................... 11
6.1
6.2
7.
Device Operation Flow ....................................................................................................... 11
6.1.1
Standard SPI Instructions ..................................................................................................... 11
6.1.2
Dual SPI Instructions ............................................................................................................ 12
6.1.3
Quad SPI Instructions ........................................................................................................... 12
6.1.4
Hold Function........................................................................................................................ 12
Write Protection .................................................................................................................. 13
PROTECTION, CONFIGURATION AND STATUS REGISTERS .................................................. 14
7.1
7.2
7.3
Protection Register / Status Register-1 (Volatile Writable, OTP lockable) ........................ 14
7.1.1
Block Protect Bits (BP3, BP2, BP1, BP0, TB) – Volatile Writable, OTP lockable.................. 14
7.1.2
Write Protection Enable Bit (WP-E) – Volatile Writable, OTP lockable ................................. 15
7.1.3
Status Register Protect Bits (SRP1, SRP0) – Volatile Writable, OTP lockable ..................... 15
Configuration Register / Status Register-2 (Volatile Writable) ........................................... 16
7.2.1
One Time Program Lock Bit (OTP-L) – OTP lockable .......................................................... 16
7.2.2
Enter OTP Access Mode Bit (OTP-E) – Volatile Writable ..................................................... 16
7.2.3
Status Register-1 Lock Bit (SR1-L) – OTP lockable ............................................................. 16
7.2.4
ECC Enable Bit (ECC-E) – Volatile Writable ......................................................................... 17
7.2.5
Buffer Read / Continuous Read Mode Bit (BUF) – Volatile Writable ..................................... 17
Status Register-3 (Status Only).......................................................................................... 18
7.3.1
Look-Up Table Full (LUT-F) – Status Only............................................................................ 18
7.3.2
Cumulative ECC Status (ECC-1, ECC-0) – Status Only ....................................................... 18
7.3.3
Program/Erase Failure (P-FAIL, E-FAIL) – Status Only ........................................................ 19
-1-
W25N01GVxxIG/IT
7.4
8.
Write Enable Latch (WEL) – Status Only .............................................................................. 19
7.3.5
Erase/Program In Progress (BUSY) – Status Only ............................................................... 19
7.3.6
Reserved Bits – Non Functional ........................................................................................... 19
W25N01GV Status Register Memory Protection ............................................................... 20
INSTRUCTIONS ............................................................................................................................. 21
8.1
8.2
9.
7.3.4
Device ID and Instruction Set Tables ................................................................................. 21
8.1.1
Manufacturer and Device Identification ................................................................................. 21
8.1.2
Instruction Set Table 1 (Continuous Read, BUF = 0, xxIT Default Power Up Mode) ............ 22
8.1.3
Instruction Set Table 2 (Buffer Read, BUF = 1, xxIG Default Power Up Mode) .................... 23
Instruction Descriptions ...................................................................................................... 25
8.2.1
Device Reset (FFh) ............................................................................................................... 25
8.2.2
Read JEDEC ID (9Fh) .......................................................................................................... 26
8.2.3
Read Status Register (0Fh / 05h) ......................................................................................... 27
8.2.4
Write Status Register (1Fh / 01h) ......................................................................................... 28
8.2.5
Write Enable (06h) ................................................................................................................ 29
8.2.6
Write Disable (04h) ............................................................................................................... 29
8.2.7
Bad Block Management (A1h) .............................................................................................. 30
8.2.8
Read BBM Look Up Table (A5h) .......................................................................................... 31
8.2.9
Last ECC Failure Page Address (A9h) ................................................................................. 32
8.2.10
128KB Block Erase (D8h) ................................................................................................... 33
8.2.11
Load Program Data (02h) / Random Load Program Data (84h) ......................................... 34
8.2.12
Quad Load Program Data (32h) / Quad Random Load Program Data (34h) ...................... 35
8.2.13
Program Execute (10h) ....................................................................................................... 36
8.2.14
Page Data Read (13h) ........................................................................................................ 37
8.2.15
Read Data (03h) ................................................................................................................. 38
8.2.16
Fast Read (0Bh) ................................................................................................................. 39
8.2.17
Fast Read with 4-Byte Address (0Ch)................................................................................. 40
8.2.18
Fast Read Dual Output (3Bh) ............................................................................................. 41
8.2.19
Fast Read Dual Output with 4-Byte Address (3Ch)............................................................. 42
8.2.20
Fast Read Quad Output (6Bh) ............................................................................................ 43
8.2.21
Fast Read Quad Output with 4-Byte Address (6Ch) ........................................................... 44
8.2.22
Fast Read Dual I/O (BBh) ................................................................................................... 45
8.2.23
Fast Read Dual I/O with 4-Byte Address (BCh) .................................................................. 46
8.2.24
Fast Read Quad I/O (EBh) ................................................................................................. 47
8.2.25
Fast Read Quad I/O with 4-Byte Address (ECh) ................................................................. 49
8.2.26
Accessing Unique ID / Parameter / OTP Pages (OTP-E=1) ............................................... 51
8.2.27
Parameter Page Data Definitions ....................................................................................... 53
ELECTRICAL CHARACTERISTICS .............................................................................................. 54
9.1
Absolute Maximum Ratings................................................................................................ 54
9.2
Operating Ranges .............................................................................................................. 54
-2-
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
10.
11.
9.3
Power-up Power-down Timing Requirements ................................................................... 55
9.4
DC Electrical Characteristics .............................................................................................. 56
9.5
AC Measurement Conditions ............................................................................................. 57
9.6
AC Electrical Characteristics .............................................................................................. 58
9.7
Serial Output Timing ........................................................................................................... 60
9.8
Serial Input Timing.............................................................................................................. 60
9.9
/HOLD Timing ..................................................................................................................... 60
9.10
/WP Timing ......................................................................................................................... 60
PACKAGE SPECIFICATIONS ....................................................................................................... 61
10.1
8-Pad WSON 8x6-mm (Package Code ZE) ....................................................................... 61
10.2
24-Ball TFBGA 8x6-mm (Package Code TB, 5x5-1 Ball Array)......................................... 62
10.3
24-Ball TFBGA 8x6-mm (Package Code TC, 6x4 Ball Array)............................................ 63
ORDERING INFORMATION .......................................................................................................... 64
11.1
12.
Valid Part Numbers and Top Side Marking ........................................................................ 65
REVISION HISTORY ...................................................................................................................... 66
-3-
W25N01GVxxIG/IT
Table of Figures
Figure 1a. W25N01GV Pad Assignments, 8-pad WSON 8x6-mm (Package Code ZE) .............................. 7
Figure 1b. W25N01GV Ball Assignments, 24-ball TFBGA 8x6-mm (Package Code TB & TC)................... 8
Figure 2. W25N01GV Flash Memory Architecture and Addressing ........................................................... 10
Figure 3. W25N01GV Flash Memory Operation Diagram .......................................................................... 11
Figure 4a. Protection Register / Status Register-1 (Address Axh) ............................................................. 14
Figure 4b. Configuration Register / Status Register-2 (Address Bxh) ........................................................ 16
Figure 4c. Status Register-3 (Address Cxh) ............................................................................................... 18
Figure 5. Device Reset Instruction .............................................................................................................. 25
Figure 6. Read JEDEC ID Instruction ......................................................................................................... 26
Figure 7. Read Status Register Instruction ................................................................................................. 27
Figure 8. Write Status Register-1/2/3 Instruction ........................................................................................ 28
Figure 9. Write Enable Instruction............................................................................................................... 29
Figure 10. Write Disable Instruction ............................................................................................................ 29
Figure 11. Bad Block Management Instruction ........................................................................................... 30
Figure 12. Read BBM Look Up Table Instruction ....................................................................................... 31
Figure 13. Last ECC Failure Page Address Instruction .............................................................................. 32
Figure 14. 128KB Block Erase Instruction .................................................................................................. 33
Figure 15. Load / Random Load Program Data Instruction ........................................................................ 34
Figure 16. Quad Load / Quad Random Load Program Data Instruction .................................................... 35
Figure 17. Program Execute Instruction ..................................................................................................... 36
Figure 18. Page Data Read Instruction ...................................................................................................... 37
Figure 19a. Read Data Instruction (Buffer Read Mode, BUF=1) ................................................................ 38
Figure 19b. Read Data Instruction (Continuous Read Mode, BUF=0) ....................................................... 38
Figure 20a. Fast Read Instruction (Buffer Read Mode, BUF=1) ................................................................ 39
Figure 20b. Fast Read Instruction (Continuous Read Mode, BUF=0)........................................................ 39
Figure 21a. Fast Read with 4-Byte Address Instruction (Buffer Read Mode, BUF=1) ............................... 40
Figure 21b. Fast Read with 4-Byte Address Instruction (Continuous Read Mode, BUF=0) ...................... 40
Figure 22a. Fast Read Dual Output Instruction (Buffer Read Mode, BUF=1) ............................................ 41
Figure 22b. Fast Read Dual Output Instruction (Continuous Read Mode, BUF=0) ................................... 41
Figure 23a. Fast Read Dual Output with 4-Byte Address Instruction (Buffer Read Mode, BUF=1)........... 42
Figure 23b. Fast Read Dual Output with 4-Byte Address Instruction (Continuous Read Mode, BUF=0) .. 42
Figure 24a. Fast Read Quad Output Instruction (Buffer Read Mode, BUF=1) .......................................... 43
Figure 24b. Fast Read Quad Output Instruction (Continuous Read Mode, BUF=0) .................................. 43
Figure 25a. Fast Read Quad Output with 4-Byte Address Instruction (Buffer Read Mode, BUF=1) ......... 44
-4-
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
Figure 25b. Fast Read Quad Output with 4-Byte Address Instruction (Continuous Read Mode, BUF=0) 44
Figure 26a. Fast Read Dual I/O Instruction (Buffer Read Mode, BUF=1) .................................................. 45
Figure 26b. Fast Read Dual I/O Instruction (Continuous Read Mode, BUF=0) ......................................... 45
Figure 27a. Fast Read Dual I/O with 4-Byte Address Instruction (Buffer Read Mode, BUF=1) ................. 46
Figure 27b. Fast Read Dual I/O with 4-Byte Address Instruction (Continuous Read Mode, BUF=0) ........ 46
Figure 28a. Fast Read Quad I/O Instruction (Buffer Read Mode, BUF=1)................................................. 47
Figure 28b. Fast Read Quad I/O Instruction (Continuous Read Mode, BUF=0) ........................................ 48
Figure 29a. Fast Read Quad I/O with 4-Byte Address Instruction (Buffer Read Mode, BUF=1) ............... 49
Figure 29b. Fast Read Quad I/O with 4-Byte Address Instruction (Continuous Read Mode, BUF=0)....... 50
Figure 30a. Power-up Timing and Voltage Levels ...................................................................................... 55
Figure 30b. Power-up, Power-Down Requirement ..................................................................................... 55
Figure 31. AC Measurement I/O Waveform ............................................................................................... 57
-5-
W25N01GVxxIG/IT
1. GENERAL DESCRIPTIONS
The W25N01GV (1G-bit) Serial SLC NAND Flash Memory provides a storage solution for systems with
limited space, pins and power. The W25N SpiFlash family incorporates the popular SPI interface and the
traditional large NAND non-volatile memory space. They are ideal for code shadowing to RAM, executing
code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The device operates on a single
2.7V to 3.6V power supply with current consumption as low as 25mA active and 10µA for standby. All
W25N SpiFlash family devices are offered in space-saving packages which were impossible to use in the
past for the typical NAND flash memory.
The W25N01GV 1G-bit memory array is organized into 65,536 programmable pages of 2,048-bytes
each. The entire page can be programmed at one time using the data from the 2,048-Byte internal buffer.
Pages can be erased in groups of 64 (128KB block erase). The W25N01GV has 1,024 erasable blocks.
The W25N01GV supports the standard Serial Peripheral Interface (SPI), Dual/Quad I/O SPI: Serial Clock,
Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up
to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and
416MHz (104MHz x 4) for Quad I/O when using the Fast Read Dual/Quad I/O instructions.
The W25N01GV provides a new Continuous Read Mode that allows for efficient access to the entire
memory array with a single Read command. This feature is ideal for code shadowing applications.
A Hold pin, Write Protect pin and programmable write protection, provide further control flexibility.
Additionally, the device supports JEDEC standard manufacturer and device ID, one 2,048-Byte Unique ID
page, one 2,048-Byte parameter page and ten 2,048-Byte OTP pages. To provide better NAND flash
memory manageability, user configurable internal ECC, bad block management are also available in
W25N01GV.
2. FEATURES
 New W25N Family of SpiFlash Memories
– W25N01GV: 1G-bit / 128M-byte
– Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
– Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
– Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
– Compatible SPI serial flash commands
 Highest Performance Serial NAND Flash
– 104MHz Standard/Dual/Quad SPI clocks
– 208/416MHz equivalent Dual/Quad SPI
– 50MB/S continuous data transfer rate
– Fast Program/Erase performance
– More than 100,000 erase/program cycles
– More than 10-year data retention
 Efficient “Continuous Read Mode”(1)
– Alternative method to the Buffer Read Mode
– No need to issue “Page Data Read”
between Read commands
– Allows direct read access to the entire array
 Low Power, Wide Temperature Range
– Single 2.7 to 3.6V supply
– 25mA active, 10µA standby current
– -40°C to +85°C operating range
 Flexible Architecture with 128KB blocks
– Uniform 128K-Byte Block Erase
– Flexible page data load methods
 Advanced Features
– On chip 1-Bit ECC for memory array
– ECC status bits indicate ECC results
– bad block management and LUT(2) access
– Software and Hardware Write-Protect
– Power Supply Lock-Down and OTP protection
– 2KB Unique ID and 2KB parameter pages
– Ten 2KB OTP pages(3)
 Space Efficient Packaging
– 8-pad WSON 8x6-mm
– 24-ball TFBGA 8x6-mm
– Contact Winbond for other package options
Notes:
1.
2.
3.
-6-
Only the Read command structures are different between
the “Continuous Read Mode (BUF=0)” and the “Buffer
Read Mode (BUF=1)”, all other commands are identical.
W25N01GVxxIG: Default BUF=1 after power up
W25N01GVxxIT: Default BUF=0 after power up
LUT stands for Look-Up Table.
OTP pages can only be programmed.
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
3. PACKAGE TYPES AND PIN CONFIGURATIONS
W25N01GV is offered in an 8-pad WSON 8x6-mm (package code ZE), and two 24-ball 8x6-mm TFBGA
(package code TB & TC) packages as shown in Figure 1a-b respectively. Package diagrams and
dimensions are illustrated at the end of this datasheet.
3.1 Pad Configuration WSON 8x6-mm
Top View
/CS
1
8
VCC
DO (IO1)
2
7
/HOLD (IO3)
/WP (IO2)
3
6
CLK
GND
4
5
DI (IO0)
Figure 1a. W25N01GV Pad Assignments, 8-pad WSON 8x6-mm (Package Code ZE)
3.2
Pad Description WSON 8x6-mm
PAD NO.
PAD NAME
I/O
1
/CS
I
2
DO (IO1)
I/O
Data Output (Data Input Output 1)(1)
3
/WP (IO2)
I/O
Write Protect Input ( Data Input Output 2)(2)
4
GND
5
DI (IO0)
I/O
6
CLK
I
7
/HOLD (IO3)
I/O
8
VCC
FUNCTION
Chip Select Input
Ground
Data Input (Data Input Output 0)(1)
Serial Clock Input
Hold Input (Data Input Output 3)(2)
Power Supply
Notes:
1. IO0 and IO1 are used for Standard and Dual SPI instructions
2. IO0 – IO3 are used for Quad SPI instructions, /WP & /HOLD functions are only available for Standard/Dual SPI.
-7-
W25N01GVxxIG/IT
3.3
Ball Configuration TFBGA 8x6-mm (5x5 or 6x4 Ball Array)
Top View
Top View
A2
A3
A4
A5
A1
A2
A3
A4
NC
NC
NC
NC
NC
NC
NC
NC
B1
B2
B3
B4
B1
B2
B3
B4
B5
NC
CLK
GND
VCC
NC
CLK
GND
VCC
NC
C1
C2
C3
C4
C1
C2
C3
C4
C5
NC
/CS
NC
/WP (IO2)
D3
D4
NC
/CS
NC
/WP (IO2)
NC
D1
D2
D1
D2
D3
D4
D5
NC
DO(IO1)
NC
DO(IO1)
NC
E1
E2
E3
E4
E1
E2
E3
E4
E5
NC
NC
NC
NC
NC
NC
NC
NC
NC
DI(IO0) /HOLD(IO3)
Package Code TB
DI(IO0) /HOLD(IO3)
F1
F2
F3
F4
NC
NC
NC
NC
Package Code TC
Figure 1b. W25N01GV Ball Assignments, 24-ball TFBGA 8x6-mm (Package Code TB & TC)
3.4
Ball Description TFBGA 8x6-mm
BALL NO.
PIN NAME
I/O
FUNCTION
B2
CLK
I
B3
GND
Ground
B4
VCC
Power Supply
C2
/CS
I
C4
/WP (IO2)
I/O
Write Protect Input (Data Input Output 2)(2)
D2
DO (IO1)
I/O
Data Output (Data Input Output 1)(1)
D3
DI (IO0)
I/O
Data Input (Data Input Output 0)(1)
D4
/HOLD (IO3)
I/O
Hold Input (Data Input Output 3)(2)
Multiple
NC
Serial Clock Input
Chip Select Input
No Connect
Notes:
1. IO0 and IO1 are used for Standard and Dual SPI instructions
2. IO0 – IO3 are used for Quad SPI instructions, /WP & /HOLD functions are only available for Standard/Dual SPI.
-8-
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
4. PIN DESCRIPTIONS
4.1 Chip Select (/CS)
The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is
deselected and the Serial Data Output (DO, or IO0, IO1, IO2, IO3) pins are at high impedance. When
deselected, the devices power consumption will be at standby levels unless an internal erase, program or
write status register cycle is in progress. When /CS is brought low the device will be selected, power
consumption will increase to active levels and instructions can be written to and data read from the
device. After power-up, /CS must transition from high to low before a new instruction will be accepted.
The /CS input must track the VCC supply level at power-up and power-down (see “Write Protection” and
Figure 30b). If needed, a pull-up resistor on the /CS pin can be used to accomplish this.
4.2 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3)
The W25N01GV supports standard SPI, Dual SPI and Quad SPI operation. Standard SPI instructions
use the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the
rising edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to
read data or status from the device on the falling edge of CLK.
Dual and Quad SPI instructions use the bidirectional IO pins to serially write instructions, addresses or
data to the device on the rising edge of CLK and read data or status from the device on the falling edge of
CLK.
4.3 Write Protect (/WP)
The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in
conjunction with the Status Register’s Block Protect bits BP[3:0] and Status Register Protect SRP bits
SRP[1:0], a portion as small as 256K-Byte (2x128KB blocks) or up to the entire memory array can be
hardware protected. The WP-E bit in the Protection Register (SR-1) controls the functions of the /WP pin.
When WP-E=0, the device is in the Software Protection mode that only SR-1 can be protected. The /WP
pin functions as a data I/O pin for the Quad SPI operations, as well as an active low input pin for the Write
Protection function for SR-1. Refer to section 7.1.3 for detail information.
When WP-E=1, the device is in the Hardware Protection mode that /WP becomes a dedicated active low
input pin for the Write Protection of the entire device. If /WP is tied to GND, all “Write/Program/Erase”
functions are disabled. The entire device (including all registers, memory array, OTP pages) will become
read-only. Quad SPI read operations are also disabled when WP-E is set to 1.
4.4 HOLD (/HOLD)
During Standard and Dual SPI operations, the /HOLD pin allows the device to be paused while it is
actively selected. When /HOLD is brought low, while /CS is low, the DO pin will be at high impedance and
signals on the DI and CLK pins will be ignored (don’t care). When /HOLD is brought high, device
operation can resume. The /HOLD function can be useful when multiple devices are sharing the same
SPI signals. The /HOLD pin is active low.
When a Quad SPI Read/Buffer Load command is issued, /HOLD pin will become a data I/O pin for the
Quad operations and no HOLD function is available until the current Quad operation finishes.
4.5 Serial Clock (CLK)
The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI
Operations")
-9-
W25N01GVxxIG/IT
5. BLOCK DIAGRAM
2,112 Bytes
Column Address CA[11:0]
64
Byte
Data Buffer (2,048 Byte)
1,024 Blocks X 64 Pages
(65,536 Pages)
Page Address PA[15:0]
Main Array
64 X
64B
Block (64 Pages, 64 X 2KB)
Address Bits
SpiFlash (up to 128M-Bit)
SpiFlash (up to 32G-Bit)
Serial NAND (1G-Bit)
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Page Address (256 Pages)
Byte Address (0-255 Byte)
X X X X X X X X 64KB Block Addr (256 Blocks)
64KB Block Address
Page Address (256 Pages)
Byte Address (0-255 Byte)
Page Address (PA) [15:0]
Column Address (CA) [11:0]
X X X X
X X X X
128KB Block Addr (1024 Blocks)
Page Addr (64 Pages) Ext
Byte Address (0-2047 Byte)
Main Memory Array (2,048-Byte)
ECC Protected
Page
Structure
(2,112-Byte)
Sector 0
512-Byte
Sector 1
512-Byte
Sector 2
512-Byte
Column
Address
000h -- 1FFh
200h -- 3FFh
400h -- 5FFh
Sector 3
512-Byte
Byte
Bad Block User Data
Definition Marker
II
Byte
Address
0
1
2
3
Spare Area (64-Byte)
Spare 0
16-Byte
Spare 1
16-Byte
Spare 3
16-Byte
600h -- 7FFh 800h -- 80Fh 810h -- 81Fh 820h -- 82Fh 830h -- 83Fh
User Data
I
4
Spare 2
16-Byte
5
No ECC
Protection
6
ECC for
Sector 0
7
8
9
A
B
ECC for
Spare
C
D
E
F
ECC for
Byte 4 to Byte D
ECC
Protected
Figure 2. W25N01GV Flash Memory Architecture and Addressing
- 10 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
6.
FUNCTIONAL DESCRIPTIONS
6.1 Device Operation Flow
Power Up
(default BUF=1, ECC-E=1)
Power Up
(default BUF=0, ECC-E=1)
Initialization &
Default Page Load (00) ~500us
Initialization &
Default Page Load (00) ~500us
Read
page 00?
Read
page 00?
N
Load Page xx
tRD ~50us
Y
Y
N
Load Page xx
tRD ~50us
Start “Buffer Read” with column address
(Page 00 or Page xx)
Start “Continuous Read” from column 0
(Page 00 or Page xx)
Set BUF=0
Set BUF=1
Load Page yy
tRD ~50us
Load Page yy
tRD ~50us
Start “Continuous Read” from column 0
(Page yy)
Start “Buffer Read” with column address
(Page yy)
W25N01GVxxIG
W25N01GVxxIT
Figure 3. W25N01GV Flash Memory Operation Diagram
6.1.1 Standard SPI Instructions
The W25N01GV is accessed through an SPI compatible bus consisting of four signals: Serial Clock
(CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions
use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of
CLK. The DO output pin is used to read data or status from the device on the falling edge of CLK.
SPI bus operation Mode 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and
Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is
not being transferred to the Serial Flash. For Mode 0, the CLK signal is normally low on the falling and
rising edges of /CS. For Mode 3, the CLK signal is normally high on the falling and rising edges of /CS.
- 11 -
W25N01GVxxIG/IT
6.1.2 Dual SPI Instructions
The W25N01GV supports Dual SPI operation when using instructions such as “Fast Read Dual Output
(3Bh)” and “Fast Read Dual I/O (BBh)”. These instructions allow data to be transferred to or from the
device at two to three times the rate of ordinary Serial Flash devices. The Dual SPI Read instructions are
ideal for quickly downloading code to RAM upon power-up (code-shadowing) or for executing non-speedcritical code directly from the SPI bus (XIP). When using Dual SPI instructions, the DI and DO pins
become bidirectional I/O pins: IO0 and IO1.
6.1.3 Quad SPI Instructions
The W25N01GV supports Quad SPI operation when using instructions such as “Fast Read Quad Output
(6Bh)”, “Fast Read Quad I/O (EBh)” and “Quad Program Data Load (32h/34h)”. These instructions allow
data to be transferred to or from the device four to six times the rate of ordinary Serial Flash. The Quad
Read instructions offer a significant improvement in continuous and random access transfer rates
allowing fast code-shadowing to RAM or execution directly from the SPI bus (XIP). When using Quad SPI
instructions the DI and DO pins become bidirectional IO0 and IO1, and the /WP and /HOLD pins become
IO2 and IO3 respectively.
6.1.4
Hold Function
For Standard SPI and Dual SPI operations, the /HOLD signal allows the W25N01GV operation to be
paused while it is actively selected (when /CS is low). The /HOLD function may be useful in cases where
the SPI data and clock signals are shared with other devices. For example, consider if the page buffer
was only partially written when a priority interrupt requires use of the SPI bus. In this case the /HOLD
function can save the state of the instruction and the data in the buffer so programming can resume
where it left off once the bus is available again. The /HOLD function is only available for standard SPI and
Dual SPI operation, not during Quad SPI. When a Quad SPI command is issued, /HOLD pin will act as a
dedicated IO pin (IO3).
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on the
rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD
condition will terminate after the next falling edge of CLK. During a /HOLD condition, the Serial Data
Output (DO) is high impedance, and Serial Data Input (DI) and Serial Clock (CLK) are ignored. The Chip
Select (/CS) signal should be kept active (low) for the full duration of the /HOLD operation to avoid
resetting the internal logic state of the device.
- 12 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
6.2
Write Protection
Applications that use non-volatile memory must take into consideration the possibility of noise and other
adverse system conditions that may compromise data integrity. To address this concern, the W25N01GV
provides several means to protect the data from inadvertent writes.






Device resets when VCC is below threshold
Write enable/disable instructions and automatic write disable after erase or program
Software and Hardware (/WP pin) write protection using Protection Register (SR-1)
Lock Down write protection for Protection Register (SR-1) until the next power-up
One Time Program (OTP) write protection for memory array using Protection Register (SR-1)
Hardware write protection using /WP pin when WP-E is set to 1
Upon power-up or at power-down, the W25N01GV will maintain a reset condition while VCC is below the
threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 30a). While reset, all
operations are disabled and no instructions are recognized. During power-up and after the VCC voltage
exceeds VWI, all program and erase related instructions are further disabled for a time delay of tPUW. This
includes the Write Enable, Program Execute, Block Erase and the Write Status Register instructions.
Note that the chip select pin (/CS) must track the VCC supply level at power-up until the VCC-min level
and tVSL time delay is reached, and it must also track the VCC supply level at power-down to prevent
adverse command sequence. If needed a pull-up resister on /CS can be used to accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register Write
Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Program Execute or
Block Erase instruction will be accepted. After completing a program or erase instruction the Write Enable
Latch (WEL) is automatically cleared to a write-disabled state of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting
the Status Register Protect (SRP0, SRP1) and Block Protect (TB, BP[3:0]) bits. These settings allow a
portion or the entire memory array to be configured as read only. Used in conjunction with the Write
Protect (/WP) pin, changes to the Status Register can be enabled or disabled under hardware control.
See Protection Register section for further information.
The WP-E bit in Protection Register (SR-1) is used to enable the hardware protection. When WP-E is set
to 1, bringing /WP low in the system will block any Write/Program/Erase command to the W25N01GV, the
device will become read-only. The Quad SPI operations are also disabled when WP-E is set to 1.
- 13 -
W25N01GVxxIG/IT
7.
PROTECTION, CONFIGURATION AND STATUS REGISTERS
Three Status Registers are provided for W25N01GV: Protection Register (SR-1), Configuration Register
(SR-2) & Status Register (SR-3). Each register is accessed by Read Status Register and Write Status
Register commands combined with 1-Byte Register Address respectively.
The Read Status Register instruction (05h / 0Fh) can be used to provide status on the availability of the
flash memory array, whether the device is write enabled or disabled, the state of write protection, Read
modes, Protection Register/OTP area lock status, Erase/Program results, ECC usage/status. The Write
Status Register instruction can be used to configure the device write protection features, Software/Hardware
write protection, Read modes, enable/disable ECC, Protection Register/OTP area lock. Write access to the
Status Register is controlled by the state of the non-volatile Status Register Protect bits (SRP0, SRP1), the
Write Enable instruction, and when WP-E is set to 1, the /WP pin.
7.1
Protection Register / Status Register-1 (Volatile Writable, OTP lockable)
S7
S6
S5
S4
S3
S2
S1
S0
SRP0
BP3
BP2
BP1
BP0
TB
WP-E
SRP1
Status Register Protect-0
(Volatile Writable, OTP Lock)
Block Protect Bits
(Volatile Writable, OTP Lock)
Top/Bottom Protect Bit
(Volatile Writable, OTP Lock)
/WP Enable Bit
(Volatile Writable, OTP Lock)
Status Register Protect-1
(Volatile Writable, OTP Lock)
Figure 4a. Protection Register / Status Register-1 (Address Axh)
7.1.1 Block Protect Bits (BP3, BP2, BP1, BP0, TB) – Volatile Writable, OTP lockable
The Block Protect bits (BP3, BP2, BP1, BP0 & TB) are volatile read/write bits in the status register-1 (S6,
S5, S4, S3 & S2) that provide Write Protection control and status. Block Protect bits can be set using the
Write Status Register Instruction. All, none or a portion of the memory array can be protected from
Program and Erase instructions (see Status Register Memory Protection table). The default values for the
Block Protection bits are 1 after power up to protect the entire array. If the SR1-L bit in the Configuration
Register (SR-2) is set to 1, the default values will the values that are OTP locked.
- 14 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
7.1.2 Write Protection Enable Bit (WP-E) – Volatile Writable, OTP lockable
The Write Protection Enable bit (WP-E) is a volatile read/write bits in the status register-1 (S1). The WP-E
bit, in conjunction with SRP1 & SRP0, controls the method of write protection: software protection,
hardware protection, power supply lock-down or one time programmable (OTP) protection, /WP pin
functionality, and Quad SPI operation enable/disable. When WP-E = 0 (default value), the device is in
Software Protection mode, /WP & /HOLD pins are multiplexed as IO pins, and Quad program/read
functions are enabled all the time. When WP-E is set to 1, the device is in Hardware Protection mode, all
Quad functions are disabled and /WP & /HOLD pins become dedicated control input pins.
7.1.3 Status Register Protect Bits (SRP1, SRP0) – Volatile Writable, OTP lockable
The Status Register Protect bits (SRP1 and SRP0) are volatile read/write bits in the status register (S0
and S7). The SRP bits control the method of write protection: software protection, hardware protection,
power supply lock-down or one time programmable (OTP) protection.
Software Protection (Driven by Controller, Quad Program/Read is enabled)
SRP1
SRP0
WP-E
/WP / IO2
Descriptions
0
0
0
X
No /WP functionality
/WP pin will always function as IO2
0
1
0
0
SR-1 cannot be changed (/WP = 0 during Write Status)
/WP pin will function as IO2 for Quad operations
0
1
0
1
SR-1 can be changed (/WP = 1 during Write Status)
/WP pin will function as IO2 for Quad operations
1
0
0
X
Power Lock Down(1) SR-1
/WP pin will always function as IO2
1
1
0
X
Enter OTP mode to protect SR-1 (allow SR1-L=1)
/WP pin will always function as IO2
Hardware Protection (System Circuit / PCB layout, Quad Program/Read is disabled)
SRP1
SRP0
WP-E
/WP only
Descriptions
0
X
1
VCC
SR-1 can be changed
1
0
1
VCC
Power Lock-Down(1) SR-1
1
1
1
VCC
Enter OTP mode to protect SR-1 (allow SR1-L=1)
X
X
1
GND
All "Write/Program/Erase" commands are blocked
Entire device (SRs, Array, OTP area) is read-only
Notes:
1. When SRP1, SRP0 = (1, 0), a power-down, power-up cycle will change SRP1, SRP0 to (0, 0) state.
- 15 -
W25N01GVxxIG/IT
7.2
Configuration Register / Status Register-2 (Volatile Writable)
S7
S6
S5
S4
S3
S2
S1
S0
OTP-L
OTP-E
SR1-L
ECC-E
BUF
(R)
(R)
(R)
OTP Data Pages Lock
(OTP Lock)
Enter OTP Mode
(Volatile Writable)
Status Register-1 Lock
(OTP Lock)
Enable ECC
(Volatile Writable)
Buffer Mode
(Volatile Writable)
Reserved
Figure 4b. Configuration Register / Status Register-2 (Address Bxh)
7.2.1
One Time Program Lock Bit (OTP-L) – OTP lockable
In addition to the main memory array, W25N01GV also provides an OTP area for the system to store
critical data that cannot be changed once it’s locked. The OTP area consists of 10 pages of 2,112-Byte
each. The default data in the OTP area are FFh. Only Program command can be issued to the OTP area
to change the data from “1” to “0”, and data is not reversible (“0” to “1”) by the Erase command. Once the
correct data is programmed in and verified, the system developer can set OTP-L bit to 1, so that the
entire OTP area will be locked to prevent further alteration to the data.
7.2.2 Enter OTP Access Mode Bit (OTP-E) – Volatile Writable
The OTP-E bit must be set to 1 in order to use the standard Program/Read commands to access the
OTP area as well as to read the Unique ID / Parameter Page information. The default value after power
up or a RESET command is 0.
7.2.3 Status Register-1 Lock Bit (SR1-L) – OTP lockable
The SR1-L lock bit is used to OTP lock the values in the Protection Register (SR-1). Depending on the
settings in the SR-1, the device can be configured to have a portion of or up to the entire array to be
write-protected, and the setting can be OTP locked by setting SR1-L bit to 1. SR1-L bit can only be set to
1 permanently when SRP1 & SRP0 are set to (1,1), and OTP Access Mode must be entered (OTP-E=1)
to execute the programming. Please refer to 8.2.26 for detailed information.
- 16 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
7.2.4
ECC Enable Bit (ECC-E) – Volatile Writable
W25N01GV has a built-in ECC algorithm that can be used to preserve the data integrity. Internal ECC
calculation is done during page programming, and the result is stored in the extra 64-Byte area for each
page. During the data read operation, ECC engine will verify the data values according to the previously
stored ECC information and to make necessary corrections if needed. The verification and correction
status is indicated by the ECC Status Bits. ECC function is enabled by default when power on (ECC-E=1),
and it will not be reset to 0 by the Device Reset command.
7.2.5 Buffer Read / Continuous Read Mode Bit (BUF) – Volatile Writable
W25N01GV provides two different modes for read operations, Buffer Read Mode (BUF=1) and
Continuous Read Mode (BUF=0). Prior to any Read operation, a Page Data Read command is needed to
initiate the data transfer from a specified page in the memory array to the Data Buffer. By default, after
power up, the data in page 0 will be automatically loaded into the Data Buffer and the device is ready to
accept any read commands.
The Buffer Read Mode (BUF=1) requires a Column Address to start outputting the existing data inside the
Data Buffer, and once it reaches the end of the data buffer (Byte 2,111), DO (IO1) pin will become high-Z
state.
The Continuous Read Mode (BUF=0) doesn’t require the starting Column Address. The device will
always start output the data from the first column (Byte 0) of the Data buffer, and once the end of the data
buffer (Byte 2,048) is reached, the data output will continue through the next memory page. With
Continuous Read Mode, it is possible to read out the entire memory array using a single read command.
Please refer to respective command descriptions for the dummy cycle requirements for each read
commands under different read modes.
For W25N01GVxxIG part number, the default value of BUF bit after power up is 1. BUF bit can be written
to 0 in the Status Register-2 to perform the Continuous Read operation.
For W25N01GVxxIT part number, the default value of BUF bit after power up is 0. BUF bit can be written
to 1 in the Status Register-2 to perform the Buffer Read operation.
BUF
ECC-E
Read Mode
(Starting from Buffer)
ECC Status
Data Output Structure
1
0
Buffer Read
N/A
2,048 + 64
1
1
Buffer Read
Page based
2,048 + 64
0
0
Continuous Read
N/A
2,048
0
1
Continuous Read
Operation based
2,048
- 17 -
W25N01GVxxIG/IT
7.3
Status Register-3 (Status Only)
S7
S6
S5
S4
S3
S2
S1
S0
(R)
LUT-F
ECC-1
ECC-0
P-FAIL
E-FAIL
WEL
BUSY
Reserved
BBM LUT Full
(Status Only)
ECC Status Bit[1:0]
(Status-Only)
Program Failure
(Status-Only)
Erase Failure
(Status-Only)
Write Enable Latch
(Status-Only)
Operation In Progress
(Status-Only)
Figure 4c. Status Register-3 (Address Cxh)
7.3.1 Look-Up Table Full (LUT-F) – Status Only
To facilitate the NAND flash memory bad block management, the W25N01GV is equipped with an
internal Bad Block Management Look-Up-Table (BBM LUT). Up to 20 bad memory blocks may be
replaced by a good memory block respectively. The addresses of the blocks are stored in the internal
Look-Up Table as Logical Block Address (LBA, the bad block) & Physical Block Address (PBA, the good
block). The LUT-F bit indicates whether the 20 memory block links have been fully utilized or not. The
default value of LUT-F is 0, once all 20 links are used, LUT-F will become 1, and no more memory block
links may be established.
7.3.2 Cumulative ECC Status (ECC-1, ECC-0) – Status Only
ECC function is used in NAND flash memory to correct limited memory errors during read operations.
The ECC Status Bits (ECC-1, ECC-0) should be checked after the completion of a Read operation to
verify the data integrity. The ECC Status bits values are don’t care if ECC-E=0. These bits will be cleared
to 0 after a power cycle or a RESET command.
- 18 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
ECC Status
Descriptions
ECC-1
ECC-0
0
0
Entire data output is successful, without any ECC correction.
0
1
Entire data output is successful, with 1~4 bit/page ECC corrections in either a
single page or multiple pages.
0
Entire data output contains more than 4 bits errors only in a single page
which cannot be repaired by ECC.
In the Continuous Read Mode, an additional command can be used to read out
the Page Address (PA) which had the errors.
1
Entire data output contains more than 4 bits errors/page in multiple pages.
In the Continuous Read Mode, the additional command can only provide the
last Page Address (PA) that had failures, the user cannot obtain the PAs for
other failure pages. Data is not suitable to use.
1
1
Notes:
1. ECC-1,ECC-0 = (1,1) is only applicable during Continuous Read operation (BUF=0).
7.3.3
Program/Erase Failure (P-FAIL, E-FAIL) – Status Only
The Program/Erase Failure Bits are used to indicate whether the internally-controlled Program/Erase
operation was executed successfully or not. These bits will also be set respectively when the Program or
Erase command is issued to a locked or protected memory array or OTP area. Both bits will be cleared at
the beginning of the Program Execute or Block Erase instructions as well as the device RESET
instruction.
7.3.4 Write Enable Latch (WEL) – Status Only
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to 1 after executing a
Write Enable Instruction. The WEL status bit is cleared to 0 when the device is write disabled. A write
disable state occurs upon power-up or after any of the following instructions: Write Disable, Program
Execute, Block Erase, Page Data Read and Program Execute for OTP pages.
7.3.5 Erase/Program In Progress (BUSY) – Status Only
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is powering up
or executing a Page Data Read, BBM Management, Program Execute, Block Erase, Program Execute for
OTP area, OTP Locking or after a Continuous Read instruction. During this time the device will ignore
further instructions except for the Read Status Register and Read JEDEC ID instructions. When the
program, erase or write status register instruction has completed, the BUSY bit will be cleared to a 0 state
indicating the device is ready for further instructions.
7.3.6
Reserved Bits – Non Functional
There are a few reserved Status Register bits that may be read out as a “0” or “1”. It is recommended to
ignore the values of those bits. During a “Write Status Register” instruction, the Reserved Bits can be
written as “0”, but there will not be any effects.
- 19 -
W25N01GVxxIG/IT
7.4
W25N01GV Status Register Memory Protection
STATUS REGISTER(1)
W25N01GV (1G-BIT / 128M-BYTE) MEMORY PROTECTION(2)
TB
BP3
BP2
BP1
BP0
PROTECTED
BLOCK(S)
PROTECTED
PAGE ADDRESS
PA[15:0]
PROTECTED
DENSITY
PROTECTED
PORTION
X
0
0
0
0
NONE
NONE
NONE
NONE
0
0
0
0
1
1022 & 1023
FF80h - FFFFh
256KB
Upper 1/512
0
0
0
1
0
1020 thru 1023
FF00h - FFFFh
512KB
Upper 1/256
0
0
0
1
1
1016 thru 1023
FE00h - FFFFh
1MB
Upper 1/128
0
0
1
0
0
1008 thru 1023
FC00h - FFFFh
2MB
Upper 1/64
0
0
1
0
1
992 thru 1023
F800h - FFFFh
4MB
Upper 1/32
0
0
1
1
0
960 thru 1023
F000h - FFFFh
8MB
Upper 1/16
0
0
1
1
1
896 thru 1023
E000h - FFFFh
16MB
Upper 1/8
0
1
0
0
0
768 thru 1023
C000h - FFFFh
32MB
Upper 1/4
0
1
0
0
1
512 thru 1023
8000h - FFFFh
64MB
Upper 1/2
1
0
0
0
1
0&1
0000h – 007Fh
256KB
Lower 1/512
1
0
0
1
0
0 thru 3
0000h - 00FFh
512KB
Lower 1/256
1
0
0
1
1
0 thru 7
0000h - 01FFh
1MB
Lower 1/128
1
0
1
0
0
0 thru 15
0000h - 03FFh
2MB
Lower 1/64
1
0
1
0
1
0 thru 31
0000h - 07FFh
4MB
Lower 1/32
1
0
1
1
0
0 thru 63
0000h - 0FFFh
8MB
Lower 1/16
1
0
1
1
1
0 thru 127
0000h - 1FFFh
16MB
Lower 1/8
1
1
0
0
0
0 thru 255
0000h - 3FFFh
32MB
Lower 1/4
1
1
0
0
1
0 thru 511
0000h - 7FFFh
64MB
Lower 1/2
X
1
0
1
X
0 thru 1023
0000h - FFFFh
128MB
ALL
X
1
1
X
X
0 thru 1023
0000h - FFFFh
128MB
ALL
Notes:
1. X = don’t care
2. If any Erase or Program command specifies a memory region that contains protected data portion, this command will be
ignored.
- 20 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8. INSTRUCTIONS
The Standard/Dual/Quad SPI instruction set of the W25N01GV consists of 27 basic instructions that are
fully controlled through the SPI bus (see Instruction Set Table1, 2). Instructions are initiated with the
falling edge of Chip Select (/CS). The first byte of data clocked into the DI input provides the instruction
code. Data on the DI input is sampled on the rising edge of clock with most significant bit (MSB) first.
Instructions vary in length from a single byte to several bytes and may be followed by address bytes, data
bytes, dummy bytes (don’t care), and in some cases, a combination. Instructions are completed with the
rising edge of edge /CS. Clock relative timing diagrams for each instruction are included in Figures 5
through 29. All read instructions can be completed after any clocked bit. However, all instructions that
Write, Program or Erase must complete on a byte boundary (/CS driven high after a full 8-bits have been
clocked) otherwise the instruction will be ignored. This feature further protects the device from inadvertent
writes. Additionally, while the device is performing Program or Erase operation, BBM management, Page
Data Read or OTP locking operations, BUSY bit will be high, and all instructions except for Read Status
Register or Read JEDEC ID will be ignored until the current operation cycle has completed.
8.1
8.1.1
Device ID and Instruction Set Tables
Manufacturer and Device Identification
MANUFACTURER ID
(MF7 - MF0)
Winbond Serial Flash
EFh
Device ID
(ID15 - ID0)
W25N01GV
AA21h
- 21 -
W25N01GVxxIG/IT
8.1.2
Instruction Set Table 1 (Continuous Read, BUF = 0, xxIT Default Power Up Mode)(11)
Commands
OpCode
Byte2
Byte3
Byte4
Byte5
Device RESET
FFh
JEDEC ID
9Fh
Dummy
EFh
AAh
21h
Read Status Register
0Fh / 05h
SR Addr
S7-0
S7-0
S7-0
Write Status Register
1Fh / 01h
SR Addr
S7-0
Write Enable
06h
Byte6
Byte7
Byte8
Byte9
S7-0
S7-0
S7-0
S7-0
Write Disable
04h
BB Management
(Swap Blocks)
A1h
LBA
LBA
PBA
PBA
Read BBM LUT
A5h
Dummy
LBA0
LBA0
PBA0
PBA0
LBA1
LBA1
PBA1
Last ECC failure
Page Address
A9h
Dummy
PA15-8
PA7-0
Block Erase
D8h
Dummy
PA15-8
PA7-0
02h
CA15-8
CA7-0
Data-0
Data-1
Data-2
Data-3
Data-4
Data-5
84h
CA15-8
CA7-0
Data-0
Data-1
Data-2
Data-3
Data-4
Data-5
32h
CA15-8
CA7-0
Data-0 / 4
Data-1 / 4
Data-2 / 4
Data-3 / 4
Data-4 / 4
Data-5 / 4
34h
CA15-8
CA7-0
Data-0 / 4
Data-1 / 4
Data-2 / 4
Data-3 / 4
Data-4 / 4
Data-5 / 4
Program Execute
10h
Dummy
PA15-8
PA7-0
Page Data Read
13h
Dummy
PA15-8
PA7-0
Read
03h
Dummy
Dummy
Dummy
D7-0
D7-0
D7-0
D7-0
D7-0
Fast Read
0Bh
Dummy
Dummy
Dummy
Dummy
D7-0
D7-0
D7-0
D7-0
Fast Read
with 4-Byte Address
0Ch
Dummy
Dummy
Dummy
Dummy
Dummy
D7-0
D7-0
D7-0
Fast Read Dual Output
3Bh
Dummy
Dummy
Dummy
Dummy
D7-0 / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
Fast Read Dual Output
with 4-Byte Address
3Ch
Dummy
Dummy
Dummy
Dummy
Dummy
D7-0 / 2
D7-0 / 2
D7-0 / 2
Fast Read Quad Output
6Bh
Dummy
Dummy
Dummy
Dummy
D7-0 / 4
D7-0 / 4
D7-0 / 4
D7-0 / 4
Fast Read Quad Output
with 4-Byte Address
6Ch
Dummy
Dummy
Dummy
Dummy
Dummy
D7-0 / 4
D7-0 / 4
D7-0 / 4
Fast Read Dual I/O
BBh
Dummy / 2
Dummy / 2
Dummy / 2
Dummy / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
Fast Read Dual I/O
with 4-Byte Address
BCh
Dummy / 2
Dummy / 2
Dummy / 2
Dummy / 2
Dummy / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
Fast Read Quad I/O
EBh
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
D7-0 / 4
D7-0 / 4
Fast Read Quad I/O
with 4-Byte Address
ECh
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
D7-0 / 4
Program Data Load
(Reset Buffer)
Random Program
Data Load
Quad Program
Data Load (Reset Buffer)
Random Quad Program
Data Load
- 22 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.1.3
Instruction Set Table 2 (Buffer Read, BUF = 1, xxIG Default Power Up Mode)(12)
Commands
OpCode
Byte2
Byte3
Byte4
Byte5
Device RESET
FFh
JEDEC ID
9Fh
Dummy
EFh
AAh
21h
Read Status Register
0Fh / 05h
SR Addr
S7-0
S7-0
S7-0
Write Status Register
1Fh / 01h
SR Addr
S7-0
Write Enable
06h
Byte6
Byte7
Byte8
Byte9
S7-0
S7-0
S7-0
S7-0
Write Disable
04h
BB Management
(Swap Blocks)
A1h
LBA
LBA
PBA
PBA
Read BBM LUT
A5h
Dummy
LBA0
LBA0
PBA0
PBA0
LBA1
LBA1
PBA1
Last ECC failure
Page Address
A9h
Dummy
PA15-8
PA7-0
Block Erase
D8h
Dummy
PA15-8
PA7-0
02h
CA15-8
CA7-0
Data-0
Data-1
Data-2
Data-3
Data-4
Data-5
84h
CA15-8
CA7-0
Data-0
Data-1
Data-2
Data-3
Data-4
Data-5
32h
CA15-8
CA7-0
Data-0 / 4
Data-1 / 4
Data-2 / 4
Data-3 / 4
Data-4 / 4
Data-5 / 4
34h
CA15-8
CA7-0
Data-0 / 4
Data-1 / 4
Data-2 / 4
Data-3 / 4
Data-4 / 4
Data-5 / 4
Program Execute
10h
Dummy
PA15-8
PA7-0
Page Data Read
13h
Dummy
PA15-8
PA7-0
Read
03h
CA15-8
CA7-0
Dummy
D7-0
D7-0
D7-0
D7-0
D7-0
Fast Read
0Bh
CA15-8
CA7-0
Dummy
D7-0
D7-0
D7-0
D7-0
D7-0
Fast Read
with 4-Byte Address
0Ch
CA15-8
CA7-0
Dummy
Dummy
Dummy
D7-0
D7-0
D7-0
Fast Read Dual Output
3Bh
CA15-8
CA7-0
Dummy
D7-0 / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
Fast Read Dual Output
with 4-Byte Address
3Ch
CA15-8
CA7-0
Dummy
Dummy
Dummy
D7-0 / 2
D7-0 / 2
D7-0 / 2
Fast Read Quad Output
6Bh
CA15-8
CA7-0
Dummy
D7-0 / 4
D7-0 / 4
D7-0 / 4
D7-0 / 4
D7-0 / 4
Fast Read Quad Output
with 4-Byte Address
6Ch
CA15-8
CA7-0
Dummy
Dummy
Dummy
D7-0 / 4
D7-0 / 4
D7-0 / 4
Fast Read Dual I/O
BBh
CA15-8 / 2
CA7-0 / 2
Dummy / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
Fast Read Dual I/O
with 4-Byte Address
BCh
CA15-8 / 2
CA7-0 / 2
Dummy / 2
Dummy / 2
Dummy / 2
D7-0 / 2
D7-0 / 2
D7-0 / 2
Fast Read Quad I/O
EBh
CA15-8 / 4
CA7-0 / 4
Dummy / 4
Dummy / 4
D7-0 / 4
D7-0 / 4
D7-0 / 4
D7-0 / 4
Fast Read Quad I/O
with 4-Byte Address
ECh
CA15-8 / 4
CA7-0 / 4
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
Dummy / 4
D7-0 / 4
Program Data Load
(Reset Buffer)
Random Program
Data Load
Quad Program
Data Load (Reset Buffer)
Random Quad Program
Data Load
- 23 -
W25N01GVxxIG/IT
Notes:
1.
Output designates data output from the device.
2.
Column Address (CA) only requires CA[11:0], CA[15:12] are considered as dummy bits.
3.
Page Address (PA) requires 16 bits. PA[15:6] is the address for 128KB blocks (total 1,024 blocks), PA[5:0] is
the address for 2KB pages (total 64 pages for each block).
4.
Logical and Physical Block Address (LBA & PBA) each consists of 16 bits. LBA[9:0] & PBA[9:0] are effective
Block Addresses. LBA[15:14] is used for additional information.
5.
Status Register Addresses:
Status Register 1 / Protection Register:
Status Register 2 / Configuration Register:
Status Register 3 / Status Register:
6.
Dual SPI Address Input (CA15-8 / 2 and CA7-0 / 2) format:
IO0 = x, x, CA10, CA8, CA6, CA4, CA2,
IO1 = x, x, CA11, CA9, CA7, CA5, CA3,
7.
Dual SPI Data Output (D7-0 / 2) format:
IO0 = D6, D4, D2, D0, ……
IO1 = D7, D5, D3, D1, ……
8.
Quad SPI Address Input (CA15-8 / 4 and CA7-0 / 4) format:
IO0 = x, CA8,
CA4, CA0
IO1 = x, CA9,
CA5, CA1
IO2 = x, CA10, CA6, CA2
IO3 = x, CA11, CA7,
CA3
9.
Quad SPI Data Input/Output (D7-0 / 4) format:
IO0 = D4, D0, ……
IO1 = D5, D1, ……
IO2 = D6, D2, ……
IO3 = D7, D3, ……
Addr = Axh
Addr = Bxh
Addr = Cxh
CA0
CA1
10. All Quad Program/Read commands are disabled when WP-E bit is set to 1 in the Protection Register.
11. For all Read operations in the Continuous Read Mode, once the /CS signal is brought to high to terminate
the read operation, the device will still remain busy for ~5us (BUSY=1), and all the data inside the Data
buffer will be lost and un-reliable to use. A new Page Data Read instruction must be issued to reload the
correct page data into the Data Buffer.
12. For all Read operations in the Buffer Read Mode, as soon as /CS signal is brought to high to terminate the
read operation, the device will be ready to accept new instructions and all the data inside the Data Buffer will
remain unchanged from the previous Page Data Read instruction.
- 24 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2
8.2.1
Instruction Descriptions
Device Reset (FFh)
Because of the small package and the limitation on the number of pins, the W25N01GV provide a
software Reset instruction instead of a dedicated RESET pin. Once the Reset instruction is accepted, any
on-going internal operations will be terminated and the device will return to its default power-on state and
lose all the current volatile settings, such as Volatile Status Register bits. Once the Reset command is
accepted by the device, the device will take approximately tRST to reset, depending on the current
operation the device is performing, tRST can be 5us~500us. During this period, no command will be
accepted.
Data corruption may happen if there is an on-going internal Erase or Program operation when Reset
command sequence is accepted by the device. It is recommended to check the BUSY bit in Status
Register before issuing the Reset command.
/CS
Mode 3
CLK
0
1
2
3
4
5
6
Mode 0
7
Mode 3
Mode 0
Instruction (FFh)
DI
(IO0)
DO
(IO1)
High Impedance
Figure 5. Device Reset Instruction
Default values of the Status Registers after power up and Device Reset
- 25 -
W25N01GVxxIG/IT
8.2.2 Read JEDEC ID (9Fh)
The Read JEDEC ID instruction is compatible with the JEDEC standard for SPI compatible serial
memories that was adopted in 2003. The instruction is initiated by driving the /CS pin low and shifting the
instruction code “9Fh” followed by 8 dummy clocks. The JEDEC assigned Manufacturer ID byte for
Winbond (EFh) and two Device ID bytes are then shifted out on the falling edge of CLK with most
significant bit (MSB) first as shown in Figure 6. For memory type and capacity values refer to
Manufacturer and Device Identification table.
/CS
Mode 3
CLK
0
7
15
16
23
24
31
38
Mode 3
8 Dummy
Clocks
9Fh
Mfr. ID
DO
(IO1)
32
Mode 0
Instruction
DI
(IO0)
8
Mode 0
High Impedance
Device ID
EFh
*
* = MSB
AAh
*
21h
*
Figure 6. Read JEDEC ID Instruction
- 26 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.3 Read Status Register (0Fh / 05h)
The Read Status Register instructions allow the 8-bit Status Registers to be read. The instruction is
entered by driving /CS low and shifting the instruction code “0Fh or 05h” into the DI pin on the rising edge
of CLK followed by an 8-bit Status Register Address. The status register bits are then shifted out on the
DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in Figure 7. Refer to
section 7.1-3 for Status Register descriptions.
The Read Status Register instruction may be used at any time, even while a Program or Erase cycle is in
progress. This allows the BUSY status bit to be checked to determine when the cycle is complete and if
the device can accept another instruction. The Status Register can be read continuously. The instruction
is completed by driving /CS high.
/CS
Mode 3
CLK
0
7
8
15
16
17
18
19
20
21
22
23
Mode 0
0Fh / 05h
SR Address
7
6
1
0
SR Value[7:0]
DO
(IO1)
Mode 3
Mode 0
Instruction
DI
(IO0)
9
High Impedance
7
6
5
Figure 7. Read Status Register Instruction
- 27 -
4
3
2
1
0
W25N01GVxxIG/IT
8.2.4
Write Status Register (1Fh / 01h)
The Write Status Register instruction allows the Status Registers to be written. The writable Status
Register bits include: SRP[1:0], TB, BP[3:0] and WP-E bit in Status Register-1; OTP-L, OTP-E, SR1-L,
ECC-E and BUF bit in Status Register-2. All other Status Register bit locations are read-only and will not
be affected by the Write Status Register instruction.
To write the Status Register bits, the instruction is entered by driving /CS low, sending the instruction
code “1Fh or 01h”, followed by an 8-bit Status Register Address, and then writing the status register data
byte as illustrated in Figure 8.
Refer to section 7.1-3 for Status Register descriptions. After power up, factory default for BP[3:0], TB,
ECC-E bits are 1, while other bits are 0.
/CS
Mode 3
CLK
0
7
8
DO
(IO1)
15
16
17
18
19
20
21
22
23
Mode 3
Mode 0
Instruction
DI
(IO0)
9
Mode 0
1Fh / 01h
SR Address
7
6
1
SR Value[7:0]
0
7
6
5
4
3
2
1
0
High Impedance
Figure 8. Write Status Register-1/2/3 Instruction
- 28 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.5 Write Enable (06h)
The Write Enable instruction (Figure 9) sets the Write Enable Latch (WEL) bit in the Status Register to a
1. The WEL bit must be set prior to every Page Program, Quad Page Program and Block Erase
instruction. The Write Enable instruction is entered by driving /CS low, shifting the instruction code “06h”
into the Data Input (DI) pin on the rising edge of CLK, and then driving /CS high.
/CS
Mode 3
CLK
0
1
2
3
4
5
6
7
Mode 0
Mode 3
Mode 0
Instruction (06h)
DI
(IO0)
High Impedance
DO
(IO1)
Figure 9. Write Enable Instruction
8.2.6 Write Disable (04h)
The Write Disable instruction (Figure 10) resets the Write Enable Latch (WEL) bit in the Status Register
to a 0. The Write Disable instruction is entered by driving /CS low, shifting the instruction code “04h” into
the DI pin and then driving /CS high. Note that the WEL bit is automatically reset after Power-up and upon
completion of the Page Program, Quad Page Program, Block Erase and Reset instructions.
/CS
Mode 3
CLK
0
1
2
3
4
5
6
Mode 0
Mode 3
Mode 0
Instruction (04h)
DI
(IO0)
DO
(IO1)
7
High Impedance
Figure 10. Write Disable Instruction
- 29 -
W25N01GVxxIG/IT
8.2.7 Bad Block Management (A1h)
Due to large NAND memory density size and the technology limitation, NAND memory devices are
allowed to be shipped to the end customers with certain amount of “Bad Blocks” found in the factory
testing. Up to 2% of the memory blocks can be marked as “Bad Blocks” upon shipment, which is a
maximum of 20 blocks for W25N01GV. In order to identify these bad blocks, it is recommended to scan
the entire memory array for bad block markers set in the factory. A “Bad Block Marker” is a non-FFh data
byte stored at Byte 0 of Page 0 for each bad block. An additional marker is also stored in the first byte of
the 64-Byte spare area.
W25N01GV offers a convenient method to manage the bad blocks typically found in NAND flash memory
after extensive use. The “Bad Block Management” command is initiated by shifting the instruction code
“A1h” into the DI pin and followed by the 16-bit “Logical Block Address” and 16-bit “Physical Block
Address” as illustrated in Figure 11. The logical block address is the address for the “bad” block that will
be replaced by the “good” block indicated by the physical block address.
Once a Bad Block Management command is successfully executed, the specified LBA-PBA link will be
added to the internal Look Up Table (LUT). Up to 20 links can be established in the non-volatile LUT. If all
20 links have been written, the LUT-F bit in the Status Register will become a 1, and no more LBA-PBA
links can be established. Therefore, prior to issuing the Bad Block Management command, the LUT-F bit
value can be checked or a “Read BBM Look Up Table” command can be issued to confirm if spare links
are still available in the LUT.
/CS
Mode 3
CLK
0
7
8
15
DO
(IO1)
23
24
31
32
39
Mode 3
Mode 0
Instruction
DI
(IO0)
16
Mode 0
A1h
LBA
[15:8]
PBA
[7:0]
[15:8]
[7:0]
High Impedance
Figure 11. Bad Block Management Instruction
- 30 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.8 Read BBM Look Up Table (A5h)
The internal Look Up Table (LUT) consists of 20 Logical-Physical memory block links (from LBA0/PBA0
to LBA19/PBA19). The “Read BBM Look Up Table” command can be used to check the existing address
links stored inside the LUT.
The “Read BBM Look Up Table” command is initiated by shifting the instruction code “A5h” into the DI pin
and followed by 8-bit dummy clocks, at the falling edge of the 16th clocks, the device will start to output
the 16-bit “Logical Block Address” and the 16-bit “Physical Block Address” as illustrated in Figure 12. All
block address links will be output sequentially starting from the first link (LBA0 & PBA0) in the LUT. If
there are available links that are unused, the output will contain all “00h” data.
The MSB bits LBA[15:14] of each link are used to indicate the status of the link.
LBA[15]
(Enable)
LBA[14]
(Invalid)
0
0
This link is available to use.
1
0
This link is enabled and it is a valid link.
1
1
This link was enabled, but it is not valid any more.
0
1
Not applicable.
Descriptions
/CS
Mode 3
CLK
0
7
Instruction
DI
(IO0)
8
15
16
23
24
31
32
40
47
48
8 Dummy
Clocks
A5h
LBA0
DO
(IO1)
39
Mode 0
High Impedance
[15:8]
*
PBA0
[7:0]
* = MSB
[15:8]
*
Figure 12. Read BBM Look Up Table Instruction
- 31 -
[7:0]
[15:8]
*
W25N01GVxxIG/IT
8.2.9 Last ECC Failure Page Address (A9h)
To better manage the data integrity, W25N01GV implements internal ECC correction for the entire
memory array. When the ECC-E bit in the Status/Configuration Register is set to 1 (also power up
default), the internal ECC algorithm is enabled for all Program and Read operations. During a “Program
Execute” command for a specific page, the ECC algorithm will calculate the ECC information based on
the data inside the 2K-Byte data buffer and write the ECC data into the extra 64-Byte ECC area in the
same physical memory page.
During the Read operations, ECC information will be used to verify the data read out from the physical
memory array and possible corrections can be made to limited amount of data bits that contain errors.
The ECC Status Bits (ECC-1 & ECC-0) will also be set indicating the result of ECC calculation.
For the “Continuous Read Mode (BUF=0)” operation, multiple pages of main array data can be read out
continuously by issuing a single read command. Upon finishing the read operation, the ECC status bits
should be check to verify if there’s any ECC correction or un-correctable errors existed in the read out
data. If ECC-1 & ECC-0 equal to (1, 0) or (1, 1), the previous read out data contain one or more pages
that contain ECC un-correctable errors. The failure page address (or the last page address if it’s multiple
pages) can be obtained by issuing the “Last ECC failure Page Address” command as illustrated in Figure
13. The 16-bit Page Address that contains un-correctable ECC errors will be presented on the DO pin
following the instruction code “A9h” and 8-bit dummy clocks on the DI pin.
/CS
Mode 3
CLK
0
7
8
15
16
17
29
30
31
Mode 3
Mode 0
8 Dummy
Clocks
Instruction
DI
(IO0)
9
Mode 0
A9h
Page Address[15:0]
DO
(IO1)
High Impedance
15
14
13
2
1
0
Figure 13. Last ECC Failure Page Address Instruction
- 32 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.10 128KB Block Erase (D8h)
The 128KB Block Erase instruction sets all memory within a specified block (64-Pages, 128K-Bytes) to
the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept
the Block Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving
the /CS pin low and shifting the instruction code “D8h” followed by 8-bit dummy clocks and the 16-bit
page address. The Block Erase instruction sequence is shown in Figure 14.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE (See AC Characteristics). While the Block Erase cycle
is in progress, the Read Status Register instruction may still be accessed for checking the status of the
BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished
and the device is ready to accept other instructions again. After the Block Erase cycle has finished the
Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase instruction will not be
executed if the addressed block is protected by the Block Protect (TB, BP2, BP1, and BP0) bits.
/CS
Mode 3
CLK
0
7
DO
(IO1)
9
15
16
17
29
30
31
Mode 3
Mode 0
Instruction
DI
(IO0)
8
Mode 0
D8h
8 Dummy
Clocks
Page Address[15:0]
15
14
13
High Impedance
Figure 14. 128KB Block Erase Instruction
- 33 -
2
1
0
W25N01GVxxIG/IT
8.2.11 Load Program Data (02h) / Random Load Program Data (84h)
The Program operation allows from one byte to 2,112 bytes (a page) of data to be programmed at
previously erased (FFh) memory locations. A Program operation involves two steps: 1. Load the program
data into the Data Buffer. 2. Issue “Program Execute” command to transfer the data from Data Buffer to
the specified memory page.
A Write Enable instruction must be executed before the device will accept the Load Program Data
Instructions (Status Register bit WEL= 1). The “Load Program Data” or “Random Load Program Data”
instruction is initiated by driving the /CS pin low then shifting the instruction code “02h” or “84h” followed
by a 16-bit column address (only CA[11:0] is effective) and at least one byte of data into the DI pin. The
/CS pin must be held low for the entire length of the instruction while data is being sent to the device. If
the number of data bytes sent to the device exceeds the number of data bytes in the Data Buffer, the
extra data will be ignored by the device. The Load Program Data instruction sequence is shown in Figure
15.
Both “Load Program Data” and “Random Load Program Data” instructions share the same command
sequence. The difference is that “Load Program Data” instruction will reset the unused the data bytes in
the Data Buffer to FFh value, while “Random Load Program Data” instruction will only update the data
bytes that are specified by the command input sequence, the rest of the Data Buffer will remain
unchanged.
If internal ECC algorithm is enabled, all 2,112 bytes of data will be accepted, but the bytes designated for
ECC parity bits in the extra 64 bytes section will be overwritten by the ECC calculation. If the ECC-E bit is
set to a 0 to disable the internal ECC, the extra 64 bytes section can be used for external ECC purpose or
other usage.
/CS
Mode 3
CLK
0
7
8
9
21
22
23
24
Mode 0
Instruction
DI
(IO0)
Column Address[15:0]
02h / 84h
15
14
13
2
1
0
7
High Impedance
DO
(IO1)
/CS
24
30
31
32
38
39
40
Mode 3
CLK
Mode 0
Data-0
DI
(IO0)
DO
(IO1)
7
6
1
Data-1
0
7
6
1
Data-2111
0
7
0
7
6
1
0
High Impedance
Figure 15. Load / Random Load Program Data Instruction
- 34 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.12 Quad Load Program Data (32h) / Quad Random Load Program Data (34h)
The “Quad Load Program Data” and “Quad Random Load Program Data” instructions are identical to the
“Load Program Data” and “Random Load Program Data” in terms of operation sequence and
functionality. The only difference is that “Quad Load” instructions will input the data bytes from all four IO
pins instead of the single DI pin. This method will significantly shorten the data input time when a large
amount of data needs to be loaded into the Data Buffer. The instruction sequence is illustrated in Figure
16.
Both “Quad Load Program Data” and “Quad Random Load Program Data” instructions share the same
command sequence. The difference is that “Quad Load Program Data” instruction will reset the unused
the data bytes in the Data Buffer to FFh value, while “Quad Random Load Program Data” instruction will
only update the data bytes that are specified by the command input sequence, the rest of the Data Buffer
will remain unchanged.
When WP-E bit in the Status Register is set to a 1, all Quad SPI instructions are disabled.
/CS
Mode 3
CLK
0
7
8
DO
(IO1)
IO2
IO3
24
25
26
27
Mode 3
Mode 0
Mode 0
Column
Addr[15:0]
Instruction
DI
(IO0)
23
32h / 34h
15
High Impedance
High Impedance
High Impedance
0
4
0
4
0
4
0
4
0
5
1
5
1
5
1
5
1
6
2
6
2
6
2
6
2
7
3
7
3
7
3
7
3
Data
0
Data
1
Figure 16. Quad Load / Quad Random Load Program Data Instruction
- 35 -
Data
2111
W25N01GVxxIG/IT
8.2.13 Program Execute (10h)
The Program Execute instruction is the second step of the Program operation. After the program data are
loaded into the 2,112-Byte Data Buffer (or 2,048 bytes when ECC is enabled), the Program Execute
instruction will program the Data Buffer content into the physical memory page that is specified in the
instruction. The instruction is initiated by driving the /CS pin low then shifting the instruction code “10h”
followed by 8-bit dummy clocks and the 16-bit Page Address into the DI pin as shown in Figure 17.
After /CS is driven high to complete the instruction cycle, the self-timed Program Execute instruction will
commence for a time duration of tpp (See AC Characteristics). While the Program Execute cycle is in
progress, the Read Status Register instruction may still be used for checking the status of the BUSY bit.
The BUSY bit is a 1 during the Program Execute cycle and becomes a 0 when the cycle is finished and
the device is ready to accept other instructions again. After the Program Execute cycle has finished, the
Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Program Execute instruction will
not be executed if the addressed page is protected by the Block Protect (TB, BP2, BP1, and BP0) bits.
/CS
Mode 3
CLK
0
7
DO
(IO1)
9
15
16
17
29
30
31
Mode 3
Mode 0
Instruction
DI
(IO0)
8
Mode 0
10h
8 Dummy
Clocks
Page Address[15:0]
15
14
13
2
1
0
High Impedance
Figure 17. Program Execute Instruction
- 36 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.14 Page Data Read (13h)
The Page Data Read instruction will transfer the data of the specified memory page into the 2,112-Byte
Data Buffer. The instruction is initiated by driving the /CS pin low then shifting the instruction code “13h”
followed by 8-bit dummy clocks and the 16-bit Page Address into the DI pin as shown in Figure 18.
After /CS is driven high to complete the instruction cycle, the self-timed Read Page Data instruction will
commence for a time duration of tRD (See AC Characteristics). While the Read Page Data cycle is in
progress, the Read Status Register instruction may still be used for checking the status of the BUSY bit.
The BUSY bit is a 1 during the Read Page Data cycle and becomes a 0 when the cycle is finished and
the device is ready to accept other instructions again.
After the 2,112 bytes of page data are loaded into the Data Buffer, several Read instructions can be
issued to access the Data Buffer and read out the data. Depending on the BUF bit setting in the Status
Register, either “Buffer Read Mode” or “Continuous Read Mode” may be used to accomplish the read
operations.
/CS
Mode 3
CLK
0
7
DO
(IO1)
9
15
16
17
29
30
31
Mode 3
Mode 0
Instruction
DI
(IO0)
8
Mode 0
13h
8 Dummy
Clocks
Page Address[15:0]
15
14
13
High Impedance
Figure 18. Page Data Read Instruction
- 37 -
2
1
0
W25N01GVxxIG/IT
8.2.15
Read Data (03h)
The Read Data instruction allows one or more data bytes to be sequentially read from the Data Buffer
after executing the Read Page Data instruction. The Read Data instruction is initiated by driving the /CS
pin low and then shifting the instruction code “03h” followed by the 16-bit Column Address and 8-bit
dummy clocks or a 24-bit dummy clocks into the DI pin. After the address is received, the data byte of the
addressed Data Buffer location will be shifted out on the DO pin at the falling edge of CLK with most
significant bit (MSB) first. The address is automatically incremented to the next higher address after each
byte of data is shifted out allowing for a continuous stream of data. The instruction is completed by driving
/CS high.
The Read Data instruction sequence is shown in Figure 19a & 19b. When BUF=1, the device is in the
Buffer Read Mode. The data output sequence will start from the Data Buffer location specified by the 16bit Column Address and continue to the end of the Data Buffer. Once the last byte of data is output, the
output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read Mode, the data
output sequence will start from the first byte of the Data Buffer and increment to the next higher address.
When the end of the Data Buffer is reached, the data of the first byte of next memory page will be
following and continues through the entire memory array. This allows using a single Read instruction to
read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash memory
command sequence.
/CS
Mode 3
CLK
0
7
8
9
21
22
23
31
32
38
39
40
46
47
Mode 0
Instruction
DI
(IO0)
8 Dummy
Clocks
Column Address[15:0]
03h
15
14
13
2
1
0
Data Out 1
High Impedance
DO
(IO1)
7
*
6
Data Out 2
1
0
7
6
1
0
7
*
* = MSB
*
Figure 19a. Read Data Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
30
31
32
38
39
40
47
03h
24 Dummy Clocks
23
22
21
2
1
0
Data Out 1
DO
(IO1)
46
Mode 0
Instruction
DI
(IO0)
29
High Impedance
7
*
6
1
* = MSB
Data Out 2
0
7
*
6
1
0
7
*
Figure 19b. Read Data Instruction (Continuous Read Mode, BUF=0)
- 38 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.16 Fast Read (0Bh)
The Fast Read instruction allows one or more data bytes to be sequentially read from the Data Buffer
after executing the Read Page Data instruction. The Fast Read instruction is initiated by driving the /CS
pin low and then shifting the instruction code “0Bh” followed by the 16-bit Column Address and 8-bit
dummy clocks or a 32-bit dummy clocks into the DI pin. After the address is received, the data byte of the
addressed Data Buffer location will be shifted out on the DO pin at the falling edge of CLK with most
significant bit (MSB) first. The address is automatically incremented to the next higher address after each
byte of data is shifted out allowing for a continuous stream of data. The instruction is completed by driving
/CS high.
The Fast Read instruction sequence is shown in Figure 20a & 20b. When BUF=1, the device is in the
Buffer Read Mode. The data output sequence will start from the Data Buffer location specified by the 16bit Column Address and continue to the end of the Data Buffer. Once the last byte of data is output, the
output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read Mode, the data
output sequence will start from the first byte of the Data Buffer and increment to the next higher address.
When the end of the Data Buffer is reached, the data of the first byte of next memory page will be
following and continues through the entire memory array. This allows using a single Read instruction to
read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash memory
command sequence.
/CS
Mode 3
CLK
0
7
8
9
21
22
23
31
32
38
39
40
46
47
Mode 0
Instruction
DI
(IO0)
8 Dummy
Clocks
Column Address[15:0]
0Bh
15
14
13
2
1
0
Data Out 1
High Impedance
DO
(IO1)
7
*
6
1
Data Out 2
0
7
6
1
0
*
* = MSB
7
*
Figure 20a. Fast Read Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
21
Instruction
DI
(IO0)
22
23
39
40
46
47
48
0Bh
55
32 Dummy Clocks
31
30
29
18
17
16
0
Data Out 1
DO
(IO1)
54
Mode 0
High Impedance
7
*
6
1
Data Out 2
0
* = MSB
Figure 20b. Fast Read Instruction (Continuous Read Mode, BUF=0)
- 39 -
7
*
6
1
0
7
*
W25N01GVxxIG/IT
8.2.17 Fast Read with 4-Byte Address (0Ch)
The Fast Read instruction allows one or more data bytes to be sequentially read from the Data Buffer
after executing the Read Page Data instruction. The Fast Read instruction is initiated by driving the /CS
pin low and then shifting the instruction code “0Ch” followed by the 16-bit Column Address and 24-bit
dummy clocks (when BUF=1) or a 40-bit dummy clocks (when BUF=0) into the DI pin. After the address
is received, the data byte of the addressed Data Buffer location will be shifted out on the DO pin at the
falling edge of CLK with most significant bit (MSB) first. The address is automatically incremented to the
next higher address after each byte of data is shifted out allowing for a continuous stream of data. The
instruction is completed by driving /CS high.
The Fast Read instruction sequence is shown in Figure 21a & 21b. When BUF=1, the device is in the
Buffer Read Mode. The data output sequence will start from the Data Buffer location specified by the 16bit Column Address and continue to the end of the Data Buffer. Once the last byte of data is output, the
output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read Mode, the data
output sequence will start from the first byte of the Data Buffer and increment to the next higher address.
When the end of the Data Buffer is reached, the data of the first byte of next memory page will be
following and continues through the entire memory array. This allows using a single Read instruction to
read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash memory
command sequence.
/CS
Mode 3
CLK
0
7
8
9
21
22
23
47
48
54
55
56
62
63
Mode 0
Instruction
DI
(IO0)
24 Dummy
Clocks
Column Address[15:0]
0Ch
15
14
13
2
1
0
Data Out 1
High Impedance
DO
(IO1)
7
6
*
1
Data Out 2
0
7
6
1
0
*
* = MSB
7
*
Figure 21a. Fast Read with 4-Byte Address Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
21
Instruction
DI
(IO0)
22
23
47
48
54
55
56
0Ch
63
40 Dummy Clocks
39
38
37
26
25
24
0
Data Out 1
DO
(IO1)
62
Mode 0
High Impedance
7
*
6
1
* = MSB
Data Out 2
0
7
6
*
1
0
7
*
Figure 21b. Fast Read with 4-Byte Address Instruction (Continuous Read Mode, BUF=0)
- 40 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.18 Fast Read Dual Output (3Bh)
The Fast Read Dual Output (3Bh) instruction is similar to the standard Fast Read (0Bh) instruction except
that data is output on two pins; IO0 and IO1. This allows data to be transferred at twice the rate of
standard SPI devices.
The Fast Read Dual Output instruction sequence is shown in Figure 22a & 22b. When BUF=1, the device
is in the Buffer Read Mode. The data output sequence will start from the Data Buffer location specified by
the 16-bit Column Address and continue to the end of the Data Buffer. Once the last byte of data is
output, the output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read Mode,
the data output sequence will start from the first byte of the Data Buffer and increment to the next higher
address. When the end of the Data Buffer is reached, the data of the first byte of next memory page will
be following and continues through the entire memory array. This allows using a single Read instruction
to read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash memory
command sequence.
/CS
Mode 3
CLK
0
7
8
9
21
22
23
31
32
33
34
35
36
37
38
39
40
Mode 0
Instruction
DI
(IO0)
8 Dummy
Clocks
Column Address[15:0]
3Bh
15
14
13
2
1
0
6
4
2
0
6
1
7
4
Data Out 1
High Impedance
DO
(IO1)
7
5
*
3
2
0
6
1
7
Data Out 2
5
3
*
* = MSB
*
Figure 22a. Fast Read Dual Output Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
21
Instruction
DI
(IO0)
22
23
39
40
41
42
43
44
46
47
48
3Bh
32 Dummy Clocks
31
30
29
18
17
16
0
6
4
2
0
6
Data Out 1
DO
(IO1)
45
Mode 0
High Impedance
7
*
5
3
* = MSB
4
0
6
1
7
Data Out 2
1
7
*
Figure 22b. Fast Read Dual Output Instruction (Continuous Read Mode, BUF=0)
- 41 -
2
5
3
*
W25N01GVxxIG/IT
8.2.19 Fast Read Dual Output with 4-Byte Address (3Ch)
The Fast Read Dual Output (3Ch) instruction is similar to the standard Fast Read (0Bh) instruction except
that data is output on two pins; IO0 and IO1. This allows data to be transferred at twice the rate of
standard SPI devices.
The Fast Read Dual Output instruction sequence is shown in Figure 23a & 23b. When BUF=1, the device
is in the Buffer Read Mode. The data output sequence will start from the Data Buffer location specified by
the 16-bit Column Address and continue to the end of the Data Buffer. Once the last byte of data is
output, the output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read Mode,
the data output sequence will start from the first byte of the Data Buffer and increment to the next higher
address. When the end of the Data Buffer is reached, the data of the first byte of next memory page will
be following and continues through the entire memory array. This allows using a single Read instruction
to read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash memory
command sequence.
/CS
Mode 3
CLK
0
7
8
9
21
22
23
47
48
49
50
51
52
53
54
55
56
Mode 0
Instruction
DI
(IO0)
24 Dummy
Clocks
Column Address[15:0]
3Ch
15
14
13
2
1
0
6
4
2
0
6
1
7
Data Out 1
High Impedance
DO
(IO1)
7
5
*
3
4
2
0
6
1
7
Data Out 2
5
3
*
* = MSB
*
Figure 23a. Fast Read Dual Output with 4-Byte Address Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
29
Instruction
DI
(IO0)
30
31
47
48
49
50
51
52
54
55
56
3Ch
40 Dummy Clocks
39
38
37
18
17
16
0
6
4
2
0
6
Data Out 1
DO
(IO1)
53
Mode 0
High Impedance
7
*
5
3
* = MSB
4
2
0
6
1
7
Data Out 2
1
7
5
3
*
*
Figure 23b. Fast Read Dual Output with 4-Byte Address Instruction (Continuous Read Mode, BUF=0)
- 42 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.20
Fast Read Quad Output (6Bh)
The Fast Read Quad Output (6Bh) instruction is similar to the Fast Read Dual Output (3Bh) instruction
except that data is output on four pins, IO0, IO1, IO2, and IO3. The Fast Read Quad Output Instruction
allows data to be transferred at four times the rate of standard SPI devices.
The Fast Read Quad Output instruction sequence is shown in Figure 24a & 24b. When BUF=1, the
device is in the Buffer Read Mode. The data output sequence will start from the Data Buffer location
specified by the 16-bit Column Address and continue to the end of the Data Buffer. Once the last byte of
data is output, the output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read
Mode, the data output sequence will start from the first byte of the Data Buffer and increment to the next
higher address. When the end of the Data Buffer is reached, the data of the first byte of next memory
page will be following and continues through the entire memory array. This allows using a single Read
instruction to read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash
memory command sequence.
When WP-E bit in the Status Register is set to a 1, this instruction is disabled.
/CS
Mode 3
CLK
0
7
8
9
21
22
23
31
32
33
34
35
36
37
38
39
40
Mode 0
Instruction
DI
(IO0)
8 Dummy
Clocks
Column Address[15:0]
6Bh
15
14
13
2
1
0
High Impedance
DO
(IO1)
High Impedance
IO2
High Impedance
IO3
* = MSB
4
0
4
0
4
0
4
0
4
5
1
5
1
5
1
5
1
5
6
2
6
2
6
2
6
2
6
7
3
7
3
7
3
7
3
7
*Data
*Data
*Data
*Data
*Data
Out 1
Out 2
Out 3
Out 4
Out 5
Figure 24a. Fast Read Quad Output Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
21
Instruction
DI
(IO0)
DO
(IO1)
IO2
IO3
22
23
39
40
41
42
43
44
45
46
47
48
Mode 0
6Bh
32 Dummy Clocks
31
30
29
18
17
16
0
High Impedance
High Impedance
High Impedance
* = MSB
4
0
4
0
4
0
4
0
4
5
1
5
1
5
1
5
1
5
6
2
6
2
6
2
6
2
6
7
3
7
3
7
3
7
3
7
*Data
*Data
*Data
*Data
*Data
Out 1
Out 2
Out 3
Out 4
Out 5
Figure 24b. Fast Read Quad Output Instruction (Continuous Read Mode, BUF=0)
- 43 -
W25N01GVxxIG/IT
8.2.21
Fast Read Quad Output with 4-Byte Address (6Ch)
The Fast Read Quad Output (6Ch) instruction is similar to the Fast Read Dual Output (3Bh) instruction
except that data is output on four pins, IO0, IO1, IO2, and IO3. The Fast Read Quad Output Instruction
allows data to be transferred at four times the rate of standard SPI devices.
The Fast Read Quad Output instruction sequence is shown in Figure 25a & 25b. When BUF=1, the
device is in the Buffer Read Mode. The data output sequence will start from the Data Buffer location
specified by the 16-bit Column Address and continue to the end of the Data Buffer. Once the last byte of
data is output, the output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read
Mode, the data output sequence will start from the first byte of the Data Buffer and increment to the next
higher address. When the end of the Data Buffer is reached, the data of the first byte of next memory
page will be following and continues through the entire memory array. This allows using a single Read
instruction to read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash
memory command sequence.
When WP-E bit in the Status Register is set to a 1, this instruction is disabled.
/CS
Mode 3
CLK
0
7
8
9
21
22
23
47
48
49
50
51
52
53
54
55
56
Mode 0
Instruction
DI
(IO0)
24 Dummy
Clocks
Column Address[15:0]
6Ch
15
14
13
2
1
0
High Impedance
DO
(IO1)
High Impedance
IO2
High Impedance
IO3
* = MSB
4
0
4
0
4
0
4
0
4
5
1
5
1
5
1
5
1
5
6
2
6
2
6
2
6
2
6
7
3
7
3
7
3
7
3
7
*Data
*Data
*Data
*Data
*Data
Out 1
Out 2
Out 3
Out 4
Out 5
Figure 25a. Fast Read Quad Output with 4-Byte Address Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
29
Instruction
DI
(IO0)
DO
(IO1)
IO2
IO3
30
31
47
48
49
50
51
52
53
54
55
56
Mode 0
6Ch
40 Dummy Clocks
39
38
37
18
17
16
0
High Impedance
High Impedance
High Impedance
* = MSB
4
0
4
0
4
0
4
0
4
5
1
5
1
5
1
5
1
5
6
2
6
2
6
2
6
2
6
7
3
7
3
7
3
7
3
7
*Data
*Data
*Data
*Data
*Data
Out 1
Out 2
Out 3
Out 4
Out 5
Figure 25b. Fast Read Quad Output with 4-Byte Address Instruction (Continuous Read Mode, BUF=0)
- 44 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.22 Fast Read Dual I/O (BBh)
The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO
pins, IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to
input the Column Address or the dummy clocks two bits per clock. This reduced instruction overhead may
allow for code execution (XIP) directly from the Dual SPI in some applications.
The Fast Read Quad Output instruction sequence is shown in Figure 26a & 26b. When BUF=1, the
device is in the Buffer Read Mode. The data output sequence will start from the Data Buffer location
specified by the 16-bit Column Address and continue to the end of the Data Buffer. Once the last byte of
data is output, the output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read
Mode, the data output sequence will start from the first byte of the Data Buffer and increment to the next
higher address. When the end of the Data Buffer is reached, the data of the first byte of next memory
page will be following and continues through the entire memory array. This allows using a single Read
instruction to read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash
memory command sequence.
/CS
Mode 3
CLK
0
7
8
9
13
14
15
19
20
21
22
23
24
Instruction
DI
(IO0)
26
27
28
4 Dummy
Clocks
Column Address[15:0]
BBh
14
12
10
4
2
0
6
4
2
0
6
Data Out 1
DO
(IO1)
25
Mode 0
High Impedance
15
13
11
5
3
1
7
5
*
3
4
2
0
6
Data Out 2
1
7
5
3
1
*
* = MSB
7
*
Figure 26a. Fast Read Dual I/O Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
15
Instruction
DI
(IO0)
16
17
23
24
25
26
27
28
30
31
32
BBh
16 Dummy Clocks
30
28
26
16
14
12
0
6
31
29
27
17
15
13
1
7
4
2
0
6
1
7
Data Out 1
DO
(IO1)
29
Mode 0
High Impedance
*
5
3
* = MSB
2
0
6
1
7
Data Out 2
*
Figure 26b. Fast Read Dual I/O Instruction (Continuous Read Mode, BUF=0)
- 45 -
4
5
3
*
W25N01GVxxIG/IT
8.2.23
Fast Read Dual I/O with 4-Byte Address (BCh)
The Fast Read Dual I/O (BCh) instruction allows for improved random access while maintaining two IO
pins, IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to
input the Column Address or the dummy clocks two bits per clock. This reduced instruction overhead may
allow for code execution (XIP) directly from the Dual SPI in some applications.
The Fast Read Quad Output instruction sequence is shown in Figure 27a & 27b. When BUF=1, the
device is in the Buffer Read Mode. The data output sequence will start from the Data Buffer location
specified by the 16-bit Column Address and continue to the end of the Data Buffer. Once the last byte of
data is output, the output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read
Mode, the data output sequence will start from the first byte of the Data Buffer and increment to the next
higher address. When the end of the Data Buffer is reached, the data of the first byte of next memory
page will be following and continues through the entire memory array. This allows using a single Read
instruction to read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash
memory command sequence.
/CS
Mode 3
CLK
0
7
8
9
13
14
15
27
28
29
30
31
32
Instruction
DI
(IO0)
34
35
36
12 Dummy
Clocks
Column Address[15:0]
BCh
14
12
10
4
2
0
6
15
13
11
5
3
1
7
4
2
0
6
1
7
Data Out 1
DO
(IO1)
33
Mode 0
High Impedance
5
*
3
4
2
0
6
1
7
Data Out 2
5
3
*
* = MSB
*
Figure 27a. Fast Read Dual I/O with 4-Byte Address Instruction (Buffer Read Mode, BUF=1)
/CS
Mode 3
CLK
0
7
8
9
19
Instruction
DI
(IO0)
20
21
27
28
29
30
31
32
BCh
34
35
36
20 Dummy Clocks
38
36
34
16
14
12
0
6
4
2
0
6
Data Out 1
DO
(IO1)
33
Mode 0
High Impedance
39
37
35
17
15
13
1
7
*
5
3
* = MSB
4
2
0
6
1
7
Data Out 2
1
7
5
3
*
*
Figure 27b. Fast Read Dual I/O with 4-Byte Address Instruction (Continuous Read Mode, BUF=0)
- 46 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.24 Fast Read Quad I/O (EBh)
The Fast Read Quad I/O (EBh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except
that address and data bits are input and output through four pins IO0, IO1, IO2 and IO3 prior to the data
output. The Quad I/O dramatically reduces instruction overhead allowing faster random access for code
execution (XIP) directly from the Quad SPI.
The Fast Read Quad Output instruction sequence is shown in Figure 28a & 28b. When BUF=1, the
device is in the Buffer Read Mode. The data output sequence will start from the Data Buffer location
specified by the 16-bit Column Address and continue to the end of the Data Buffer. Once the last byte of
data is output, the output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read
Mode, the data output sequence will start from the first byte of the Data Buffer and increment to the next
higher address. When the end of the Data Buffer is reached, the data of the first byte of next memory
page will be following and continues through the entire memory array. This allows using a single Read
instruction to read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash
memory command sequence.
When WP-E bit in the Status Register is set to a 1, this instruction is disabled.
/CS
Mode 3
CLK
0
7
8
DO
(IO1)
IO2
IO3
10
11
12
13
14
15
16
17
18
19
20
21
22
EBh
High Impedance
High Impedance
High Impedance
4 Dummy
Clocks
Column
Address[15:0]
Instruction
DI
(IO0)
9
Mode 0
12
8
4
0
X
X
X
X
4
0
4
0
4
0
4
13
9
5
1
X
X
X
X
5
1
5
1
5
1
5
14
10
6
2
X
X
X
X
6
2
6
2
6
2
6
15
11
7
3
X
X
X
X
7
3
7
3
7
3
7
*
= MSB
*Data
*Data
*Data
*Data
Out 1
Out 2
Out 3
Out 4
Figure 28a. Fast Read Quad I/O Instruction (Buffer Read Mode, BUF=1)
- 47 -
W25N01GVxxIG/IT
/CS
Mode 3
CLK
0
7
8
9
13
Instruction
DI
(IO0)
DO
(IO1)
IO2
IO3
14
15
19
20
21
22
23
24
25
26
27
28
Mode 0
EBh
High Impedance
High Impedance
High Impedance
12 Dummy Clocks
44
40
36
24
20
16
0
4
0
4
0
4
0
4
0
4
45
41
37
25
21
17
1
5
1
5
1
5
1
5
1
5
46
42
38
26
22
18
2
6
2
6
2
6
2
6
2
6
47
43
39
27
23
19
3
7
3
7
3
7
3
7
3
7
* = MSB
*Data
*Data
*Data
*Data
*Data
Out 1
Out 2
Out 3
Out 4
Out 5
Figure 28b. Fast Read Quad I/O Instruction (Continuous Read Mode, BUF=0)
- 48 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.25 Fast Read Quad I/O with 4-Byte Address (ECh)
The Fast Read Quad I/O (ECh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except
that address and data bits are input and output through four pins IO0, IO1, IO2 and IO3 prior to the data
output. The Quad I/O dramatically reduces instruction overhead allowing faster random access for code
execution (XIP) directly from the Quad SPI.
The Fast Read Quad Output instruction sequence is shown in Figure 29a & 29b. When BUF=1, the
device is in the Buffer Read Mode. The data output sequence will start from the Data Buffer location
specified by the 16-bit Column Address and continue to the end of the Data Buffer. Once the last byte of
data is output, the output pin will become Hi-Z state. When BUF=0, the device is in the Continuous Read
Mode, the data output sequence will start from the first byte of the Data Buffer and increment to the next
higher address. When the end of the Data Buffer is reached, the data of the first byte of next memory
page will be following and continues through the entire memory array. This allows using a single Read
instruction to read out the entire memory array and is also compatible to Winbond’s SpiFlash NOR flash
memory command sequence.
When WP-E bit in the Status Register is set to a 1, this instruction is disabled.
/CS
Mode 3
CLK
0
7
8
DO
(IO1)
IO2
IO3
10
11
12
21
22
23
24
25
25
27
28
ECh
High Impedance
High Impedance
High Impedance
10 Dummy
Clocks
Column
Address[15:0]
Instruction
DI
(IO0)
9
Mode 0
12
8
4
0
X
X
4
0
4
0
4
0
4
13
9
5
1
X
X
5
1
5
1
5
1
5
14
10
6
2
X
X
6
2
6
2
6
2
6
15
11
7
3
X
X
7
3
7
3
7
3
7
*
= MSB
*Data
*Data
*Data
*Data
Out 1
Out 2
Out 3
Out 4
Figure 29a. Fast Read Quad I/O with 4-Byte Address Instruction (Buffer Read Mode, BUF=1)
- 49 -
W25N01GVxxIG/IT
/CS
Mode 3
CLK
0
7
8
9
15
Instruction
DI
(IO0)
DO
(IO1)
IO2
IO3
16
17
21
22
23
24
25
26
27
28
29
30
Mode 0
ECh
High Impedance
High Impedance
High Impedance
14 Dummy Clocks
52
48
44
24
20
16
0
4
0
4
0
4
0
4
0
4
53
49
45
25
21
17
1
5
1
5
1
5
1
5
1
5
54
50
46
26
22
18
2
6
2
6
2
6
2
6
2
6
55
51
47
27
23
19
3
7
3
7
3
7
3
7
3
7
* = MSB
*Data
*Data
*Data
*Data
*Data
Out 1
Out 2
Out 3
Out 4
Out 5
Figure 29b. Fast Read Quad I/O with 4-Byte Address Instruction (Continuous Read Mode, BUF=0)
- 50 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.26 Accessing Unique ID / Parameter / OTP Pages (OTP-E=1)
In addition to the main memory array, the W25N01GV is also equipped with one Unique ID Page, one
Parameter Page, and ten OTP Pages.
Page Address
Page Name
Descriptions
Data Length
00h
01h
02h
…
0Bh
Unique ID Page
Parameter Page
OTP Page [0]
OTP Pages [1:8]
OTP Page [9]
Factory programmed, Read Only
Factory programmed, Read Only
Program Only, OTP lockable
Program Only, OTP lockable
Program Only, OTP lockable
32-Byte x 16
256-Byte x 3
2,112-Byte
2,112-Byte
2,112-Byte
To access these additional data pages, the OTP-E bit in Status Register-2 must be set to “1” first. Then,
Read operations can be performed on Unique ID and Parameter Pages, Read and Program operations
can be performed on the OTP pages if it’s not already locked. To return to the main memory array
operation, OTP-E bit needs to be to set to 0.
Read Operations
A “Page Data Read” command must be issued followed by a specific page address shown in the table
above to load the page data into the main Data Buffer. After the device finishes the data loading
(BUSY=0), all Read commands may be used to read the Data Buffer starting from any specified Column
Address. Please note all Read commands must now follow the “Buffer Read Mode” command structure
(CA[15:0], number of dummy clocks) regardless the previous BUF bit setting. ECC can also be enabled
for the OTP page read operations to ensure the data integrity.
Program and OTP Lock Operations
OTP pages provide the additional space (2K-Byte x 10) to store important data or security information
that can be locked to prevent further modification in the field. These OTP pages are in an erased state set
in the factory, and can only be programmed (change data from “1” to “0”) until being locked by OTP-L bit
in the Configuration/Status Register-2. OTP-E must be first set to “1” to enable the access to these OTP
pages, then the program data must be loaded into the main Data Buffer using any “Program Data Load”
commands. The “Program Execute” command followed by a specific OTP Page Address is used to
initiate the data transfer from the Data Buffer to the OTP page. When ECC is enabled, ECC calculation
will be performed during “Program Execute”, and the ECC information will be stored into the 64-Byte
spare area.
Once the OTP pages are correctly programmed, OTP-L bit can be used to permanently lock these pages
so that no further modification is possible. While still in the “OTP Access Mode” (OTP-E=1), user needs to
set OTP-L bit in the Configuration/Status Register-2 to “1”, and issue a “Program Execute” command
without any Page Address. After the device finishes the OTP lock setting (BUSY=0), the user can set
OTP-E to “0” to return to the main memory array operation.
SR1-L OTP Lock Operation
The Protection/Status Register-1 contains protection bits that can be set to protect either a portion or the
entire memory array from being Programmed/Erased or set the device to either Software Write Protection
(WP-E=0) or Hardware Write Protection (WP-E=1). Once the BP[3:0], TB, WP-E bits are set correctly,
SRP1 and SRP0 should also be set to “1”s as well to allow SR1-L bit being set to “1” to permanently lock
the protection settings in the Status Register-1 (SR1). Similar to the OTP-L setting procedure above, in
order to set SR1-L lock bit, the device must enter the “OTP Access Mode” (OTP-E=1) first, and SR1-L bit
- 51 -
W25N01GVxxIG/IT
should be set to “1” prior to the “Program Execute” command without any Page Address. Once SR1-L is
set to “1” (BUSY=0), the user can set OTP-E to “0” to return to the main memory array operation.
- 52 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
8.2.27
Parameter Page Data Definitions
The Parameter Page contains 3 identical copies of the 256-Byte Parameter Data. The table below lists all
the key data byte locations. All other unspecified byte locations have 00h data as default.
Byte
Number
Descriptions
0~3
4~5
6~7
8~9
10~31
32~43
Parameter page signature
Revision number
Feature supported
Optional command supported
Reserved
Device manufacturer
44~63
Device model
64
65~66
67~79
80~83
84~85
86~91
92~95
96~99
100
101
102
103~104
105~106
107
108~109
110
111
112
113
114
115~127
128
129~132
133~134
135~136
137~138
139~163
164~165
166~253
254~255
256~511
512~767
768+
JEDEC manufacturer ID
Date code
Reserved
Number of data bytes per page
Number of spare bytes per page
Reserved
Number of pages per block
Number of blocks per logical unit
Number of logical units
Number of address bytes
Number of bits per cell
Bad blocks maximum per unit
Block endurance
Guaranteed valid blocks at beginning of target
Block endurance for guaranteed valid blocks
Number of programs per page
Reserved
Number of ECC bits
Number of plane address bits
Multi-plane operation attributes
Reserved
I/O pin capacitance, maximum
Reserved
Maximum page program time (us)
Maximum block erase time (us)
Maximum page read time (us)
Reserved
Vendor specific revision number
Vendor specific
Integrity CRC
Value of bytes 0~255
Value of bytes 0~255
Reserved
Values
4Fh, 4Eh, 46h, 49h
00h, 00h
00h, 00h
02h, 00h
All 00h
57h, 49h, 4Eh, 42h, 4Fh, 4Eh, 44h, 20h, 20h, 20h, 20h, 20h
57h, 32h, 35h, 4Eh, 30h, 31h, 47h, 56h, 20h, 20h,
20h, 20h, 20h, 20h, 20h, 20h, 20h, 20h, 20h, 20h
EFh
00h, 00h
All 00h
00h, 08h, 00h, 00h
40h, 00h
All 00h
40h, 00h, 00h, 00h
00h, 04h, 00h, 00h
01h
00h
01h
14h, 00h
01h, 06h
01h
00h, 00h
04h
00h
00h
00h
00h
All 00h
08h
All 00h
BCh, 02h
10h, 27h
32h, 00h
All 00h
00h, 00h
All 00h
Set at test
- 53 -
W25N01GVxxIG/IT
9. ELECTRICAL CHARACTERISTICS
9.1 Absolute Maximum Ratings (1)
PARAMETERS
SYMBOL
Supply Voltage
CONDITIONS
VCC
RANGE
UNIT
–0.6 to +4.6
V
Voltage Applied to Any Pin
VIO
Relative to Ground
–0.6 to +4.6
V
Transient Voltage on any Pin
VIOT
<20nS Transient
Relative to Ground
–2.0V to VCC+2.0V
V
5
mA
Short Circuit Output Crrent, IOs
Storage Temperature
TSTG
Lead Temperature
TLEAD
Electrostatic Discharge Voltage
VESD
–65 to +150
°C
(2)
°C
See Note
Human Body Model(3)
–2000 to +2000
V
Notes:
1. This device has been designed and tested for the specified operation ranges. Proper operation outside
of these levels is not guaranteed. Exposure to absolute maximum ratings may affect device reliability.
Exposure beyond absolute maximum ratings may cause permanent damage.
2. Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and
the European directive on restrictions on hazardous substances (RoHS) 2002/95/EU.
3. JEDEC Standard JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms).
9.2 Operating Ranges
PARAMETER
Supply Voltage
Ambient Temperature,
Operating
SYMBOL
CONDITIONS
VCC
TA
Industrial
- 54 -
SPEC
UNIT
MIN
MAX
2.7
3.6
V
–40
+85
°C
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
9.3 Power-up Power-down Timing Requirements
PARAMETER
SYMBOL
VCC (min) to /CS Low
SPEC
MIN
MAX
tVSL(1)
50
500
Time Delay Before Write Instruction
tPUW
5
Write Inhibit Threshold Voltage
VWI
(1)
1.0
(1)
UNIT
µs
ms
2.0
V
Note:
1. These parameters are characterized only.
VCC
VCC(max)
0Fh/05h/9Fh/FFh are
the only commands allowed.
Device is fully accessible
(Page 0 with ECC is ready in Buffer)
/CS must track VCC
VCC(min)
tVSL
Reset State
VWI
tPUW
Time
Figure 30a. Power-up Timing and Voltage Levels
/CS must track VCC
during VCC Ramp Up/Down
VCC
/CS
Time
Figure 30b. Power-up, Power-Down Requirement
- 55 -
W25N01GVxxIG/IT
9.4 DC Electrical Characteristics
PARAMETER
SYMBOL
CONDITIONS
Input Capacitance
CIN(1)
VIN = 0V(1)
Output Capacitance
Cout(1)
Input Leakage
SPEC
MIN
TYP
MAX
UNIT
6
pF
8
pF
ILI
±2
µA
I/O Leakage
ILO
±2
µA
Standby Current
ICC1
/CS = VCC,
VIN = GND or VCC
10
50
µA
Read Current
ICC2
C = 0.1 VCC / 0.9 VCC
DO = Open
25
35
mA
Current Page Program
ICC3
/CS = VCC
25
35
mA
Current Block Erase
ICC4
/CS = VCC
25
35
mA
Input Low Voltage
VIL
VCC x 0.3
V
Input High Voltage
VIH
Output Low Voltage
VOL
IOL = 2.1mA
Output High Voltage
VOH
IOH = –400 µA
VOUT =
0V(1)
VCC x 0.7
V
0.4
2.4
V
V
Notes:
1. Tested on sample basis and specified through design and characterization data. TA = 25° C, VCC = 3.0V.
- 56 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
9.5
AC Measurement Conditions
PARAMETER
SYMBOL
Load Capacitance
Input Rise and Fall Times
Input Pulse Voltages
Input Timing Reference Voltages
Output Timing Reference Voltages
SPEC
MIN
MAX
UNIT
CL
30
pF
TR, TF
5
ns
VIN
0.1 VCC to 0.9 VCC
V
IN
0.3 VCC to 0.7 VCC
V
OUT
0.5 VCC
V
Input and Output
Timing Reference Levels
Input Levels
0.9 VCC
0.5 VCC
0.1 VCC
Figure 31. AC Measurement I/O Waveform
- 57 -
W25N01GVxxIG/IT
9.6 AC Electrical Characteristics(3)
SPEC
DESCRIPTION
SYMBOL
ALT
UNIT
MIN
FR
Clock frequency for all instructions
Clock High, Low Time
for all instructions
fC1
D.C.
TYP
MAX
104
MHz
tCLH,
tCLL(1)
4
ns
Clock Rise Time peak to peak
tCLCH(2)
0.1
V/ns
Clock Fall Time peak to peak
tCHCL(2)
0.1
V/ns
5
ns
5
ns
/CS Active Setup Time relative to CLK
tSLCH
/CS Not Active Hold Time relative to CLK
tCHSL
Data In Setup Time
tDVCH
tDSU
2
ns
Data In Hold Time
tCHDX
tDH
3
ns
/CS Active Hold Time relative to CLK
tCHSH
3
ns
/CS Not Active Setup Time relative to CLK
tSHCH
3
ns
/CS Deselect Time (for Array Read  Array Read)
tSHSL1
tCSH
10
ns
/CS Deselect Time (for Erase, Program or Read
Status Registers  Read Status Registers)
tSHSL2
tCSH
50
ns
tSHQZ(2)
tDIS
7
ns
Clock Low to Output Valid
tCLQV
tV
7
ns
Output Hold Time
tCLQX
tHO
/HOLD Active Setup Time relative to CLK
/HOLD Active Hold Time relative to CLK
Output Disable Time
tCSS
2
ns
tHLCH
5
ns
tCHHH
5
ns
Continued – next page
- 58 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
AC Electrical Characteristics (cont’d)
SPEC
DESCRIPTION
SYMBOL
ALT
UNIT
MIN
TYP
MAX
/HOLD Not Active Setup Time relative to CLK
tHHCH
5
ns
/HOLD Not Active Hold Time relative to CLK
tCHHL
5
ns
/HOLD to Output Low-Z
tHHQX(2)
tLZ
7
ns
/HOLD to Output High-Z
tHLQZ(2)
tHZ
12
ns
Write Protect Setup Time Before /CS Low
tWHSL
20
ns
Write Protect Hold Time After /CS High
tSHWL
100
ns
Status Register Write Time
tW
50
ns
tRST(2)
5/10/500
µs
Read Page Data Time (ECC disabled)
tRD1
25
µs
Read Page Data Time (ECC enabled)
tRD2
60
µs
/CS High to next Instruction after Reset during
Page Data Read / Program Execute / Block Erase
Page Program, OTP Lock, BBM Management Time
tPP
250
700
us
Block Erase Time
tBE
2
10
ms
4
times
Number of partial page programs
Notes:
1.
2.
3.
NoP
Clock high + Clock low must be less than or equal to 1/fC.
Value guaranteed by design and/or characterization, not 100% tested in production.
Tested on sample basis and specified through design and characterization data. TA = 25° C, VCC = 3.0V.
- 59 -
W25N01GVxxIG/IT
9.7
Serial Output Timing
/CS
tCLH
CLK
9.8
tCLQV
tCLQX
tCLQX
IO
output
tCLQV
tCLL
MSB OUT
tSHQZ
LSB OUT
Serial Input Timing
/CS
tSHSL
tCHSL
tSLCH
tCHSH
tSHCH
CLK
tDVCH
IO
input
9.9
tCHDX
tCLCH
MSB IN
tCHCL
LSB IN
/HOLD Timing
/CS
tHLCH
tCHHL
tHHCH
CLK
tCHHH
/HOLD
tHLQZ
tHHQX
IO
output
IO
input
9.10 /WP Timing
/CS
tWHSL
tSHWL
/WP
CLK
IO
input
Write Status Register is allowed
- 60 -
Write Status Register is not allowed
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
10. PACKAGE SPECIFICATIONS
10.1 8-Pad WSON 8x6-mm (Package Code ZE)
Min
Millimeters
Nom
Max
Min
Inches
Nom
Max
A
0.70
0.75
0.80
0.028
0.030
0.031
A1
0.00
0.02
0.05
0.000
0.001
0.002
0.019
Symbol
b
0.35
0.40
0.48
0.014
0.016
C
---
0.20 REF
---
---
0.008 REF
---
D
7.90
8.00
8.10
0.311
0.315
0.319
D2
3.35
3.40
3.45
0.132
0.134
0.136
E
5.90
6.00
6.10
0.232
0.236
0.240
E2
4.25
4.30
4.35
0.167
0.169
0.171
e
---
1.27
---
---
0.050
---
L
0.45
0.50
0.55
0.018
0.020
0.022
y
0.00
---
0.050
0.000
---
0.002
- 61 -
W25N01GVxxIG/IT
10.2 24-Ball TFBGA 8x6-mm (Package Code TB, 5x5-1 Ball Array)
Note:
Ball land: 0.45mm.
Ball Opening: 0.35mm
PCB ball land suggested <= 0.35mm
Min
Millimeters
Nom
Max
Min
Inches
Nom
Max
A
---
---
1.20
---
---
0.047
A1
0.25
0.30
0.35
0.010
0.012
0.014
A2
---
0.85
---
---
0.033
---
b
0.35
0.40
0.45
0.014
0.016
0.018
D
7.90
8.00
8.10
0.311
0.315
0.319
6.10
0.232
Symbol
D1
E
4.00 BSC
5.90
6.00
0.157 BSC
0.236
E1
4.00 BSC
0.157 BSC
0.039 TYP
SE
1.00 TYP
SD
1.00 TYP
0.039 TYP
e
1.00 BSC
0.039 BSC
- 62 -
0.240
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
10.3 24-Ball TFBGA 8x6-mm (Package Code TC, 6x4 Ball Array)
Note:
Ball land: 0.45mm.
Ball Opening: 0.35mm
PCB ball land suggested <= 0.35mm
Min
Millimeters
Nom
Max
Min
Inches
Nom
Max
A
---
---
1.20
---
---
0.047
A1
0.25
0.30
0.35
0.010
0.012
0.014
b
0.35
0.40
0.45
0.014
0.016
0.018
D
7.95
8.00
8.05
0.313
0.315
0.317
Symbol
D1
E
5.00 BSC
5.95
6.00
0.197 BSC
6.05
0.234
0.236
E1
3.00 BSC
0.118 BSC
e
1.00 BSC
0.039 BSC
- 63 -
0.238
W25N01GVxxIG/IT
11. ORDERING INFORMATION
W(1) 25N 01G V xx
W
=
Winbond
25N
=
Serial SLC NAND Memory
01G
=
1G-bit
V =
2.7V to 3.6V
ZE = 8-pad WSON 8x6mm
TB = 24-ball TFBGA 8x6-mm (5x5 ball array)
I
=
I(1)
TC = 24-ball TFBGA 8x6-mm (6x4 ball array)
Industrial (-40°C to +85°C)
(2)
G
=
Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3)
and BUF=1 is the default value after power up
T
=
Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3)
and BUF=0 is the default value after power up
Notes:
1.
The “W” prefix is not included on the part marking.
2.
Standard bulk shipments are in tray for WSON and TFBGA packages. For other packing options, please
specify when placing orders.
- 64 -
Publication Release Date: July 08, 2015
Revision F
W25N01GVxxIG/IT
11.1 Valid Part Numbers and Top Side Marking
The following table provides the valid part numbers for the W25N01GV SpiFlash Memory. Please contact
Winbond for specific availability by density and package type. Winbond SpiFlash memories use a 12-digit
Product Number for ordering. However, due to limited space, the Top Side Marking on all packages uses
an abbreviated 11-digit number.
Industrial Temperature:
PACKAGE TYPE
DENSITY
PRODUCT NUMBER
TOP SIDE MARKING
ZE
WSON-8 8x6mm
1G-bit
W25N01GVZEIG
W25N01GVZEIT
25N01GVZEIG
25N01GVZEIT
TB
TFBGA-24 8x6mm
(5x5-1 Ball Array)
1G-bit
W25N01GVTBIG
W25N01GVTBIT
25N01GVTBIG
25N01GVTBIT
TC
TFBGA-24 8x6mm
(6x4 Ball Array)
1G-bit
W25N01GVTCIG
W25N01GVTCIT
25N01GVTCIG
25N01GVTCIT
Note:
W25N01GVxxIG: BUF=1 (Buffer Read Mode) is the default value after power up. BUF bit can be written to 0.
W25N01GVxxIT: BUF=0 (Continuous Read Mode) is the default value after power up. BUF bit can be written to 1.
- 65 -
W25N01GVxxIG/IT
12. REVISION HISTORY
VERSION
DATE
PAGE
DESCRIPTION
A
06/13/2013
New Create Preliminary
B
11/26/2013
Overall updates
C
12/13/2014
63, 65, 66
11
17, 26
D
03/23/2015
6, 10-11, 25,
63-64
E
06/08/2015
25
58
60
Updated FFh Reset command description
Updated tRD2 in AC parameter table
Updated WSON 8x6mm dimensions
F
07/08/2015
34
All
Updated instruction description
Removed Preliminary designator
Removed SOIC-16 package, updated order information
Updated Figure.3 for device operation
Changed BUF bit default value to 1 after power up
Updated W25N01GVxxIG/IT part number definitions
Trademarks
Winbond and SpiFlash are trademarks of Winbond Electronics Corporation.
All other marks are the property of their respective owner.
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in systems
or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship
instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for
other applications intended to support or sustain life. Furthermore, Winbond products are not intended for
applications wherein failure of Winbond products could result or lead to a situation wherein personal
injury, death or severe property or environmental damage could occur. Winbond customers using or
selling these products for use in such applications do so at their own risk and agree to fully indemnify
Winbond for any damages resulting from such improper use or sales.
Information in this document is provided solely in connection with Winbond products. Winbond
reserves the right to make changes, corrections, modifications or improvements to this document
and the products and services described herein at any time, without notice.
- 66 -
Publication Release Date: July 08, 2015
Revision F