TS9008 300mA High PSRR Low Noise CMOS LDO SOT-25 Pin Definition: 1. Input 2. Ground 3. Enable 4. Bypass 5. Output SOT-23 Pin Definition: 1. Input 2. Output 3. Ground General Description The TS9008 is a low dropout, high PSRR, low noise linear regulator with very low quiescent. It can supply 300mA output current with low dropout about 250mV. The Device includes pass element, error amplifier, bandgap, current-limit and thermal shutdown circuitry. The characteristics of low dropout voltage and less quiescent current make it good for some critical current application, for example, some battery powered devices. The typical quiescent current is approximately 30µA. In the shutdown mode, the maximum supply current is less than 1uA. Built-in current-limit and thermal-shutdown functions prevent any fault condition from IC damage Features Ordering Information ● Input voltage range 2.8V~5.5V ● 250mV dropout at 300mA load ● 300mA output Current ● Low quiescent current 30µA (Typ.) ● Max. supply current <1µA at shutdown mode ● Fixed output voltage ● Current limit and thermal shutdown protection ● High PSRR 73db @ 1kHz Part No. Package Packing TS9008xCX RFG SOT-23 3kpcs / 7” Reel TS9008xCX5 RFG SOT-25 3kpcs / 7” Reel Note: “G” denote for Halogen Free Product Where x denotes voltage option, available are D= 1.8V, S= 3.3V Applications ● Palmtops, PDA and Notebook Computers ● DSC, Handset Camera Modules ● PCMCIA Cards, PC Cameras ● USB Based Portable Devices (MPS, PMP) ● GSM/GPRS/3G RF Transceiver Modules Block Diagram Typical Application Circuit VIN Current Limit EN TS9008 VOUT - + Error Amp Enable Bandgap Thermal Shutdown GND BP 1/9 Version: E14 TS9008 300mA High PSRR Low Noise CMOS LDO Absolute Maximum Ratings Parameter Symbol Limit Unit VIN Pin Voltage VIN GND - 0.3 to GND + 6 V Output Voltage VOUT GND - 0.3 to VIN + 0.3 V Enable Voltage VEN GND - 0.3 to GND + 6 V Power Dissipation PD 350 mW Storage Temperature Range TSTG -40 to +150 °C Operating Temperature Range TOP -40 to +85 °C TJ -40 to +125 °C RθJC 230 °C/W Thermal Resistance from Junction to ambient RθJA 280 2 Note: RθJA is measured with the PCB copper area of approximately 1 in (Multi-layer). °C/W Junction Temperature Thermal Resistance from Junction to case Electrical Characteristics (VIN=VOUT+1V or VIN=2.8V whichever is greater, CIN=COUT=1uF, TA=25°C, unless otherwise noted) Characteristics Input Voltage Output Voltage Accuracy Quiescent Current Dropout Voltage (Note2) Current Limit Symbol Min Typ Max Units (Note1) 2.8 -- 5.5 V ∆VOUT IOUT=1mA -2 -- +2 % IQ IOUT =0mA -- µA VIN VDROP ILIMIT Line Regulation ∆VLINE Load Regulation (Note3) ∆VLOAD Ripple Rejection PSRR Enable Input Threshold Conditions IOUT=300mA 30 60 1.5V＜VOUT≦2.0V -- 1000 -- 2.8V＜VOUT≦3.3V -- 250 -- RLOAD=1Ω 300 IOUT =1mA, VIN=VOUT+1V to 5V IOUT =0m~150mA -- -- mV mA -- 1 5 mV -- 6 20 mV COUT=1uF, F=1KHz -- 73 -- IOUT =1mA F=10K -- 60 -- VENH 1.4 -- -- VENL -- -- 0.4 dB V Enable Pin Current IEH VEN=VIN -- -- 0.1 µA Shutdown Current ISD VIN=3.6V, VEN=0V -- -- 1 µA Temperature Coefficient TC IOUT=1mA, VIN=5V -- 50 -- ppm/°C Temperature Shutdown TS -- 160 -- ºC TSH -25 -Shutdown Hysterisis Note: 1. Minimum VIN voltage is defined by output adds a dropout voltage. 2. The dropout voltage is defined as VIN-VOUT, which is measured when VOUT drop about 100mV. 3. Regulation is measured at constant junction temperature by using pulsed testing with a low ON time. ºC Temperature 2/9 Version: E14 TS9008 300mA High PSRR Low Noise CMOS LDO Function Description A minimum of 1uF capacitor must be connected from VOUT to ground to insure stability. Typically a large storage capacitor is connected from VIN to ground to ensure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be dropout voltage higher than VOUT in order for the device to regulate properly Application Information Like any low-dropout regulator, the TS9008 requires input and output decoupling capacitors. The device is specifically designed for portable applications requiring minimum board space and smallest components. These capacitors must be correctly selected for good performance. Please note that linear regulators with a low dropout voltage have high internal loop gains which require care in guarding against oscillation caused by insufficient decoupling capacitance. Capacitor Selection Normally, use a 1µF capacitor on the input and a 1µF capacitor on the output of the TS9008. Larger input capacitor values and lower ESR provide better supply-noise rejection and transient response. A large value output capacitor may be necessary if large, fast transients are anticipated and the device is located several inches from the power source. The capacitors is recommended to use 1uF X5R or X7R dielectric ceramic capacitors with 30mΩ to 50mΩ ESR range between device outputs to ground for transient stability. Input-Output (Dropout) Voltage A regulator's minimum input-to-output voltage differential (dropout voltage) determines the lowest usable supply voltage. In battery-powered systems, this determines the useful end-of-life battery voltage. Because the device uses a PMOS, its dropout voltage is a function of drain-to source on-resistance, RDS(ON), multiplied by the load current: VDROPOUT = VIN -VOUT = RDS (ON) x IOUT Current limit and Thermal Shutdown Protection In order to prevent overloading or thermal condition from damaging the device, TS9008 regulator has internal thermal and current limiting functions designed to protect the device. It will rapidly shut off PMOS pass element during overloading or over temperature condition. Thermal Considerations The TS9008 series can deliver a current of up to 300mA over the full operating junction temperature range. However, the maximum output current must be dated at higher ambient temperature to ensure the junction temperature does not exceed 125°C. With all possible conditions, the junction temperature must be within the range specified under operating conditions. Power dissipation can be calculated based on the output current and the voltage drop across regulator. PD = (VIN - VOUT) IOUT The final operating junction temperature for any set of conditions can be estimated by the following thermal equation: PD (MAX) = (TJ(MAX) - TA) / RθJA Where TJ(MAX) is the maximum junction temperature of the die (125°C) and TA is the maximum ambient temperature. The junction to ambient thermal resistance (RθJA) for SOT-25 package at recommended minimum footprint is 250°C/W. 3/9 Version: E14 TS9008 300mA High PSRR Low Noise CMOS LDO PCB Layout An input capacitance 1µF is required between the TS9008 input pin and ground (the amount of the capacitance may be increased without limit), this capacitor must be located a distance of not more than 1cm from the input and return to a clean analog ground. Input capacitor can filter out the input voltage spike caused by the surge current due to the inductive effect of the package pin and the printed circuit board’s routing wire. Otherwise, the actual voltage at the VIN pin may exceed the absolute maximum rating. The output capacitor also must be located a distance of not more than 1cm from output to a clean analog ground. Because it can filter out the output spike caused by the surge current due to the inductive effect of the package pin and the printed circuit board’s routing wire. 4/9 Version: E14 TS9008 300mA High PSRR Low Noise CMOS LDO Electrical Characteristics Curve Figure 1. Output Voltage vs. Input Voltage Figure 2. Threshold Voltage vs. Input Voltage Figure 3. Quiescent Current vs. Input Voltage Figure 4. Output Current vs. Output Voltage Figure 5. Output Voltage vs. Temperature Figure 6. Load Transient Response 5/9 Version: E14 TS9008 300mA High PSRR Low Noise CMOS LDO Electrical Characteristics Curve Figure 8. Enable ON Figure 7. Power ON 6/9 Version: E14 TS9008 300mA High PSRR Low Noise CMOS LDO SOT-23 Mechanical Drawing Unit: Millimeters Marking Diagram LL Y W x = Device Code BD=1.8V BH=3.3V = Year Code 4=2014, 5=2015, 6=2016…….. = Week Code 01~26 (A~Z) 27~52 (a~z) = Interal Code 7/9 Version: E14 TS9008 300mA High PSRR Low Noise CMOS LDO SOT-25 Mechanical Drawing Unit: Millimeters Marking Diagram LL Y W x = Device Code UD=1.8V UI=3.3V = Year Code 4=2014, 5=2015, 6=2016…….. = Week Code 01~26 (A~Z) 27~52 (a~z) = Interal Code 8/9 Version: E14 TS9008 300mA High PSRR Low Noise CMOS LDO Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 9/9 Version: E14