® RT8086B 3.5A, 1.2MHz, Synchronous Step-Down Converter General Description Features The RT8086B is a high efficiency, synchronous step-down DC/DC converter. The available input voltage range is from 2.8V to 5.5V and the regulated output voltage is adjustable from 0.6V to 3.3V while delivering up to 3.5A of output current. The internal synchronous low on-resistance power switches increase efficiency and eliminate the need for an external Schottky diode. The current mode constant on-time operation with internal compensation allows the transient response to be optimized over a wide range of loads and output capacitors. TheRT8086B is available in the UQFN-12L 2x2 (FC) package. Ordering Information High Efficiency Up to 95% Ω/40mΩ Ω Low RDS(ON) Switches : 50mΩ 0.6V Reference Allows for Low Output Voltage Internal Compensation Input Voltage Range : 2.8V to 5.5V Adjustable Output Voltage from 0.6V to 3.3V 1.2MHz Switching Frequency Start-Up into Pre-Biased Load Built in Soft-Start Power Good Indication Cycle-by-Cycle Current Limit Input Under Voltage Lockout Output Under Voltage Protection (Hiccup) Thermal Shutdown Protection RoHS Compliant and Halogen Free Applications RT8086B Package Type QUF : UQFN-12L 2x2 (FC) (U-Type) Lead Plating System G : Green (Halogen Free and Pb Free) Smart Handheld devices Portable Instruments Battery-Powered Equipment Distributed Power Systems Note : Richtek products are : RoHS compliant and compatible with the current require- Marking Information 0Y : Product Code ments of IPC/JEDEC J-STD-020. 0YW Suitable for use in SnPb or Pb-free soldering processes. W : Date Code Simplified Application Circuit RT8086B LX PVIN VIN CIN PGOOD L VOUT VIN PGOOD COUT VOUT R1 Enable EN PGND Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS8086B-01 June 2014 FB AGND R2 is a registered trademark of Richtek Technology Corporation. www.richtek.com 1 RT8086B Pin Configurations (TOP VIEW) VIN PVIN LX PGND AGND 10 1 2 3 4 LX 9 11 8 12 7 PGND 5 6 PGOOD EN FB VOUT NC UQFN-12L 2x2 (FC) Functional Pin Description Pin No. Pin Name Pin Function PVIN Power Input. The available input voltage range is from 2.8V to 5.5V. A 10F or larger input capacitor is needed to reduce voltage spikes at the input. 2, 11 LX Switch Node. Output of the internal high side and low side MOSFETs. 3, 12 PGND Power Ground. 4 AGND Analog Ground. 5 NC No Internal Connection. 6 VOUT Sense Input Pin for Output Voltage. 7 FB Feedback Input. This pin used to set the output voltage of the converter to regulate to the desired value via an external resistive divider. The feedback reference voltage is 0.6V typically. 8 EN Enable Control Input. A logic-high (1.2V < EN < 5.5V) enables the converter; a logic-low forces the IC into shutdown mode. 9 PGOOD Power Good Indicator. The output of this pin is an open drain with internal pull-up resister to VIN. The output of this pin is pulled to high when the FB voltage is within 10%; otherwise it is Low. 10 VIN Supply Voltage for Internal Control Circuit. It is connected to PVIN inside the chip. 1 Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 2 is a registered trademark of Richtek Technology Corporation. DS8086B-01 June 2014 RT8086B Function Block Diagram EN VIN UVLO Shut Down Control OTP Error + Amplifier FB VREF - RC + - VOUT Ton Comparator + VIN LX PVIN Logic Control Driver - CC Current Limit Detector LX PGND + Current Sense - LX PGND AGND PGOOD Operation The RT8086B is a synchronous low voltage step-down converter that can support the input voltage range from 2.8V to 5.5V and the output current can be up to 3.5A. The RT8086B uses a constant on-time, current mode architecture. In normal operation, the high side P-MOSFET is turned on when the switch controller is set by the comparator and is turned off when the Ton comparator resets the switch controller. Low side MOSFET peak current is measured by internal RSENSE. The error amplifier EA adjusts COMP voltage by comparing the feedback signal (VFB) from the output voltage with the internal 0.6V reference. When the load current increases, it causes a drop in the feedback voltage relative to the reference, then the COMP voltage rises to allow higher inductor current to match the load current. UV Comparator If the feedback voltage (VFB) is lower than threshold voltage 0.2V, the UV comparator's output will go high and the switch controller will turn off the high side MOSFET. The output under voltage protection is designed to operate in Hiccup mode. PGOOD Comparator When the feedback voltage (VFB) is higher than threshold voltage 0.54V and under 0.66V, the PGOOD open drain output will be high impedance. Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS8086B-01 June 2014 Enable Comparator A logic-high enables the converter; a logic-low forces the IC into shutdown mode. There is an internal pull down 1MΩ resistor at EN pin. Soft-Start (SS) An internal current source charges an internal capacitor to build the soft-start ramp voltage. The VFB voltage will track the internal ramp voltage during soft-start interval. The typical soft-start time is 2ms. Over Current Protection (OCP) The RT8086B provides over current protection by detecting low side MOSFET valley inductor current. If the sensed valley inductor current is over the current limit threshold (4.5A typ.), the OCP will be triggered. When OCP is tripped, the RT8086B will keep the over current threshold level until the over current condition is removed. Thermal Shutdown (OTP) The device implements an internal thermal shutdown function when the junction temperature exceeds 140°C. The thermal shutdown forces the device to stop switching when the junction temperature exceeds the thermal shutdown threshold. Once the die temperature decreases below the hysteresis of 20°C, the device reinstates the power up sequence. is a registered trademark of Richtek Technology Corporation. www.richtek.com 3 RT8086B Absolute Maximum Ratings (Note 1) Supply Input Voltage, PVIN, VIN ------------------------------------------------------------------------------ −0.3V to 6.5V Switch Node Voltage, LX ---------------------------------------------------------------------------------------- −0.3V to (PVIN + 0.3V) Other Pins Voltage ----------------------------------------------------------------------------------------------- −0.3V to 6V Power Dissipation, PD @ TA = 25°C UQFN-12L 2x2 (FC) ---------------------------------------------------------------------------------------------- 1.25W Package Thermal Resistance (Note 2) UQFN-12L 2x2 (FC), θJA ---------------------------------------------------------------------------------------- 80°C/W UQFN-12L 2x2 (FC), θJC ---------------------------------------------------------------------------------------- 7°C/W Lead Temperature (Soldering, 10 sec.) ---------------------------------------------------------------------- 260°C Junction Temperature -------------------------------------------------------------------------------------------- 150°C Storage Temperature Range ----------------------------------------------------------------------------------- −65°C to 150°C ESD Susceptibility (Note 3) HBM (Human Body Model) ------------------------------------------------------------------------------------- 2kV Recommended Operating Conditions (Note 4) Supply Input Voltage --------------------------------------------------------------------------------------------- 2.8V to 5.5V Junction Temperature Range ----------------------------------------------------------------------------------- −40°C to 125°C Ambient Temperature Range ----------------------------------------------------------------------------------- −40°C to 85°C Electrical Characteristics (VIN = 3.3V, TA = 25°C, unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit Input Voltage PVIN 2.8 -- 5.5 V Feedback Reference Voltage VREF 0.588 0.6 0.612 V Feedback Leakage Current I FB VFB = 3.3V -- -- 1 A Quiescent Current Close loop, no load current -- 60 -- Shutdown Current Shutdown -- -- 1 Output Voltage Line Regulation VIN = 2.8V to 5.5V VIN = 5V, VOUT = 3.3V, IOUT = 0A to 3.5A VIN = 5V, VOUT = 1.2V -- 0.1 -- %/V -- 0.4 -- % -- 1.2 -- MHz Output Voltage Load Regulation Switching Frequency A High-Side RPMOS ILX = 0.3A, VIN = 5V -- 50 -- Low-Side RNMOS ILX = 0.3A, VIN = 5V -- 40 -- Current Limit I LIM Valley current 4.5 -- -- A Min. Off-Time t OFF -- 100 -- ns VIN Rising -- 2.5 -- VIN Falling -- 2.2 -- -- 140 -- Logic-High 1.2 -- 5.5 Logic-Low -- -- 0.4 Switch On-Resistance Under Voltage Lockout Threshold Thermal Shutdown Enable Voltage Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 4 m V °C V is a registered trademark of Richtek Technology Corporation. DS8086B-01 June 2014 RT8086B Parameter Symbol EN Input Current Test Conditions Min Typ Max VEN = 2V -- 2 -- VEN = 0V -- 0 -- -- 90 -- s FB with respect to the Regulation -- ±10 -- % PGOOD = PVIN -- 500 -- k PGOOD = Low -- -- 100 -- 2 -- ms VIN = 5V, VOUT = 1.2V -- 200 -- VIN = 3.6V, VOUT = 1.2V -- 277 -- PGOOD Pin Trigger Delay PGOOD Pin Threshold (Relative to VOUT) PGOOD Open Drain Impedance RPGOOD PGOOD On-Resistance Impedance Soft-Start Time TSS On-Time TON Unit A ns Note 1. Stresses beyond those listed “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Note 2. θJA is measured at TA = 25°C on a high effective thermal conductivity four-layer test board per JEDEC 51-7. Note 3. Devices are ESD sensitive. Handling precaution is recommended. Note 4. The device is not guaranteed to function outside its operating conditions. Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS8086B-01 June 2014 is a registered trademark of Richtek Technology Corporation. www.richtek.com 5 RT8086B Typical Application Circuit RT8086B 1 VIN CIN 10µF 10 9 PGOOD 8 Enable PVIN LX 2, 11 L 1µH VIN PGOOD EN VOUT FB 6 7 R1 200k *CFF COUT 20µF VOUT 1.2V R2 200k PGND AGND 3, 12 4 * : Optional Table 1. Suggested Component Values VOUT (V) R1 (k) R2 (k) L (H) COUT (F) 1.2V 200 200 1 20 1.8V 200 100 1 20 2.5V 200 63.4 1 20 3.3V 200 44.2 1 20 Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 6 is a registered trademark of Richtek Technology Corporation. DS8086B-01 June 2014 RT8086B Typical Operating Characteristics Output Voltage vs. Input Voltage Efficiency vs. Output Current 100 1.40 VIN = 3.3V 90 1.35 VIN = 5V 1.30 Output Voltage (V) Efficiency (%) 80 70 60 50 40 30 1.25 1.20 1.15 1.10 20 1.05 10 VOUT = 1.2V 0 0.001 VIN = 2.8V to 5.5V, VOUT = 1.2V 1.00 0.01 0.1 1 10 2.5 3 3.5 Output Voltage vs. Temperature 5 5.5 Output Voltage vs. Output Current 1.85 1.30 1.84 1.28 VIN = 3.3V 1.26 Output Voltage (V) 1.83 Output Voltage (V) 4.5 Input Voltage (V) Output Current (A) VIN = 5V 1.82 1.81 1.80 1.79 1.78 1.77 1.24 1.22 VIN = 5V 1.20 VIN = 3.3V 1.18 1.16 1.14 1.76 VOUT = 1.8V, IOUT = 0.6A 1.75 1.12 VOUT = 1.2V 1.10 -50 -25 0 25 50 75 100 125 0 0.5 1 Temperature (°C) 1.5 2 2.5 3 3.5 Output Current (A) Switching Frequency vs. Input Voltage Switching Frequency vs. Temperature 1.50 1.5 1.45 1.4 Switching Frequency (MHz)1 Switching Frequency (MHz)1 4 1.40 1.35 1.30 1.25 1.20 1.15 VIN = 3.3V 1.3 VIN = 5V 1.2 1.1 1.0 0.9 VOUT = 1.8V, IOUT = 0.6A VOUT = 1.2V, IOUT = 0.6A 1.10 0.8 2.5 3 3.5 4 4.5 5 Input Voltage (V) Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS8086B-01 June 2014 5.5 -50 -25 0 25 50 75 100 125 Temperature (°C) is a registered trademark of Richtek Technology Corporation. www.richtek.com 7 RT8086B Current Limit vs. Input Voltage Load Transient Response 7.0 Current Limit (A) 6.5 VOUT (50mV/Div) 6.0 5.5 5.0 IOUT (1A/Div) 4.5 VIN = 3.3V, VOUT = 1.2V, IOUT = 0.2A to 2A, COUT = 20μF VOUT = 1.2V 4.0 2.5 3 3.5 4 4.5 5 Time (50μs/Div) 5.5 Input Voltage (V) Load Transient Response Output Ripple Voltage VOUT (50mV/Div) VOUT (20mV/Div) IOUT (1A/Div) VIN = 3.3V, VOUT = 1.2V, IOUT = 1A to 2A, COUT = 20μF Time (50μs/Div) Time (10ms/Div) Output Ripple Voltage Power On from VIN VOUT (5mV/Div) VIN (2V/Div) PGOOD (5V/Div) VLX (2V/Div) VIN = 3.3V, VOUT = 1.2V, IOUT = 3.5A Time (500ns/Div) Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 8 VIN = 3.3V, VOUT = 1.2V, IOUT = 0A VOUT (1V/Div) ILX (2A/Div) VIN = 5V, VOUT = 1.2V, IOUT = 3.5A Time (2.5ms/Div) is a registered trademark of Richtek Technology Corporation. DS8086B-01 June 2014 RT8086B Power Off from VIN VIN (5V/Div) Power On from EN VEN (2V/Div) PGOOD (5V/Div) VLX (5V/Div) VOUT (1V/Div) VOUT (1V/Div) ILX (5A/Div) VIN = 5V, VOUT = 1.2V, IOUT = 3.5A Time (2.5ms/Div) ILX (2A/Div) VIN = 5V, VOUT = 1.2V, IOUT = 3.5A Time (1ms/Div) Power Off from EN VEN (2V/Div) VOUT (2V/Div) ILX (2A/Div) VIN = 5V, VOUT = 1.2V, IOUT = 0A Time (25ms/Div) Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS8086B-01 June 2014 is a registered trademark of Richtek Technology Corporation. www.richtek.com 9 RT8086B Application Information The RT8086B is a single-phase step-down converter. It provides single feedback loop, current mode control with fast transient response. An internal 0.6V reference allows the output voltage to be precisely regulated for low output voltage applications. A fixed switching frequency (1.2MHz) oscillator and internal compensation are integrated to minimize external component count. Protection features include over current protection, under voltage protection and over temperature protection. Output Voltage Setting Connect a resistive voltage divider at the FB between VOUT and GND to adjust the output voltage. The output voltage is set according to the following equation : VOUT = VREF 1 R1 R2 where VREF is the feedback reference voltage 0.6V (typ.). VOUT R1 FB R2 GND Figure 1. Setting VOUT with a Voltage Divider Chip Enable and Disable The EN pin allows for power sequencing between the controller bias voltage and another voltage rail. The RT8086B remains in shutdown if the EN pin is lower than 400mV. When the EN pin rises above the VEN trip point, the RT8086B begins a new initialization and soft-start cycle. capacitor. This voltage clamps the voltage at the FB pin, causing PWM pulse width to increase slowly and in turn reduce the input surge current. The internal 0.6V reference takes over the loop control once the internal ramping-up voltage becomes higher than 0.6V. UVLO Protection The RT8086B has input Under Voltage Lockout protection (UVLO). If the input voltage exceeds the UVLO rising threshold voltage (2.5V typ.), the converter resets and prepares the PWM for operation. If the input voltage falls below the UVLO falling threshold voltage during normal operation, the device will stop switching. The UVLO rising and falling threshold voltage has a hysteresis to prevent noise-caused reset. Inductor Selection The switching frequency (on-time) and operating point (% ripple or LIR) determine the inductor value as shown below: VOUT VIN VOUT L= fSW LIR ILOAD(MAX) VIN where LIR is the ratio of the peak-to-peak ripple current to the average inductor current. Find a low loss inductor having the lowest possible DC resistance that fits in the allotted dimensions. The core must be large enough not to saturate at the peak inductor current (IPEAK) : IPEAK = ILOAD(MAX) + LIR ILOAD(MAX) 2 The calculation above serves as a general reference. To further improve transient response, the output inductor can be further reduced. This relation should be considered along with the selection of the output capacitor. Internal Soft-Start Input Capacitor Selection The RT8086B provides an internal soft-start function to prevent large inrush current and output voltage overshoot when the converter starts up. The soft-start (SS) automatically begins once the chip is enabled. During softstart, the internal soft-start capacitor becomes charged and generates a linear ramping up voltage across the High quality ceramic input decoupling capacitor, such as X5R or X7R, with values greater than 10μF are recommended for the input capacitor. The X5R and X7R ceramic capacitors are usually selected for power regulator capacitors because the dielectric material has less capacitance variation and more temperature stability. Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 10 is a registered trademark of Richtek Technology Corporation. DS8086B-01 June 2014 RT8086B The input capacitor is used to supply the input RMS current, which can be approximately calculated using the following equation : IIN_RMS = ILOAD VOUT VOUT 1 VIN VIN The next step is selecting a proper capacitor for RMS current rating. One good design uses more than one capacitor with low equivalent series resistance (ESR) in parallel to form a capacitor bank. The input capacitance value determines the input ripple voltage of the regulator. The input voltage ripple can be approximately calculated using the following equation : VIN = IOUT(MAX) VOUT VOUT 1 CIN fSW VIN VIN Output Capacitor Selection The output capacitor and the inductor form a low pass filter in the Buck topology. In steady state condition, the ripple current flowing into/out of the capacitor results in ripple voltage. The output voltage ripple (VP-P) can be calculated by the following equation : 1 VP_P = LIR ILOAD(MAX) ESR + 8 COUT fSW When load transient occurs, the output capacitor supplies the load current before the controller can respond. Therefore, the ESR will dominate the output voltage sag during load transient. The output voltage undershoot (VSAG) can be calculated by the following equation : VSAG = ILOAD ESR For a given output voltage sag specification, the ESR value can be determined. Another parameter that has influence on the output voltage sag is the equivalent series inductance (ESL). The rapid change in load current results in di/dt during transient. Therefore, the ESL contributes to part of the voltage sag. Using a capacitor with low ESL can obtain better transient performance. Generally, using several capacitors connected in parallel can have better transient performance than using a single capacitor for the same total ESR. Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS8086B-01 June 2014 Thermal Considerations For continuous operation, do not exceed absolute maximum junction temperature. The maximum power dissipation depends on the thermal resistance of the IC package, PCB layout, rate of surrounding airflow, and difference between junction and ambient temperature. The maximum power dissipation can be calculated by the following formula : PD(MAX) = (TJ(MAX) − TA) / θJA where TJ(MAX) is the maximum junction temperature, TA is the ambient temperature, and θJA is the junction to ambient thermal resistance. For recommended operating condition specifications, the maximum junction temperature is 125°C. The junction to ambient thermal resistance, θJA, is layout dependent. For UQFN-12L 2x2(FC) package, the thermal resistance, θJA, is 80°C/W on a standard JEDEC 51-7 four-layer thermal test board. The maximum power dissipation at TA = 25°C can be calculated by the following formula : P D(MAX) = (125°C − 25°C) / (80°C/W) = 1.25W for UQFN-12L 2x2 (FC) package The maximum power dissipation depends on the operating ambient temperature for fixed T J(MAX) and thermal resistance, θJA. The derating curve in Figure 2 allows the designer to see the effect of rising ambient temperature on the maximum power dissipation. 1.6 Maximum Power Dissipation (W)1 Voltage rating and current rating are the key parameters when selecting an input capacitor. Generally, selecting an input capacitor with voltage rating 1.5 times greater than the maximum input voltage is a conservatively safe design. Four-Layer PCB 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 25 50 75 100 125 Ambient Temperature (°C) Figure 2. Derating Curve of Maximum Power Dissipation is a registered trademark of Richtek Technology Corporation. www.richtek.com 11 RT8086B Layout Considerations Layout is very important in high frequency switching converter design. The PCB can radiate excessive noise and contribute to converter instability with improper layout. Certain points must be considered before starting a layout using the RT8086B. Make the traces of the main current paths as short and wide as possible. Put the input capacitor as close as possible to the device pins (VIN and GND). LX node encounters high frequency voltage swings so it should be kept in a small area. Keep sensitive components away from the LX node to prevent stray capacitive noise pick-up. L COUT The output capacitor must be place near the IC. PVIN LX PGND AGND Ensure all feedback network connections are short and direct. Place the feedback network as close to the chip as possible. The GND pin and Exposed Pad should be connected to a strong ground plane for heat sinking and noise protection. An example of PCB layout guide is shown in Figure 3 for reference. Input capacitor must be placed as close to the IC as possible. LX should be connected to inductor by wide and short GND trace. Keep sensitive CIN1 components away from VIN this trace. VOUT CIN2 VIN 10 1 2 3 4 LX 9 11 8 12 7 PGND 5 NC 6 PGOOD EN FB VOUT R3 VIN R1 R2 VOUT AGND The voltage divider must be connected as close to the device as possible. Figure 3. PCB Layout Guide Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 12 is a registered trademark of Richtek Technology Corporation. DS8086B-01 June 2014 RT8086B Outline Dimension Symbol Dimensions In Millimeters Dimensions In Inches Min. Max. Min. Max. A 0.500 0.600 0.020 0.024 A1 0.000 0.050 0.000 0.002 A3 0.100 0.152 0.004 0.006 b 0.200 0.300 0.008 0.012 D 1.900 2.100 0.075 0.083 E 1.900 2.100 0.075 0.083 0.500 e 0.020 L 0.350 0.450 0.014 0.018 L1 0.450 0.550 0.018 0.022 U-Type 12L QFN 2x2 (FC) Package Richtek Technology Corporation 14F, No. 8, Tai Yuen 1st Street, Chupei City Hsinchu, Taiwan, R.O.C. Tel: (8863)5526789 Richtek products are sold by description only. Richtek reserves the right to change the circuitry and/or specifications without notice at any time. Customers should obtain the latest relevant information and data sheets before placing orders and should verify that such information is current and complete. Richtek cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Richtek product. Information furnished by Richtek is believed to be accurate and reliable. However, no responsibility is assumed by Richtek or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Richtek or its subsidiaries. DS8086B-01 June 2014 www.richtek.com 13