High Voltage 3-Phase Motor Driver ICs

SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
Features and Benefits
▪
▪
▪
▪
▪
▪
▪
▪
▪
▪
▪
▪
Description
Built-in pre-drive IC
MOSFET or IGBT power element
Alleviate noise generation by adjusting an internal resistor
CMOS compatible input (3.3 V and 5 V)
High-side gate driver using bootstrap circuit or floating
power supply
Built-in protection circuit for controlling power supply
voltage drop (UVLO on VBB and VCC)
Overcurrent protection (OCP), overcurrent limiting (OCL),
and thermal shutdown (TSD)
Output of fault signal during operation of protection circuit
Output current 2.0 A, 2.5 A, 3.0 A, or 5 A
Small DIP (SIM 40-pin)
Isolation rating of 1500 Vrms/min.
UL recognized component, File No.: E118037
The SIM6800M Series inverter power module (IPM) provides
a robust, highly-integrated solution for optimally controlling
3-phase motor power inverter systems and variable speed control
systems used in energy-conserving designs to drive motors of
residential and commercial appliances. This IC takes up to 5 A
(continuous) output current. It can withstand voltages of up to
600 V (IGBT breakdown voltage).
The SIM6800M Series series power package includes an IC
with all of the necessary power elements (six MOSFETs or
IGBTs and six freewheeling diodes), pre-driver ICs (two), and
bootstrap diodes (three), needed to configure the main circuit
of an inverter. This enables the main circuit of the inverter to
be configured with fewer external components than traditional
designs.
Applications include residential white goods (home
applications) and commercial appliance motor control:
• Air conditioner fan
• Small ventilation fan
• Dishwasher pump
Package: 40-pin DIP
Leadform 2971
Not to scale
Functional Block Diagram
VB1A
VB1B
VB2
VB3
SIM6800M
VCC1
VBB
UVLO
HIN1
HIN2
HIN3
UVLO
Input
Logic
UVLO
UVLO
High Side
Level Shift Driver
A
A
A
HO
W1
W2
V
V1
V2
U
COM1
SD
VCC2
UVLO
LIN 1
LIN 2
LIN 3
COM2
A
Input Logic
(OCP Reset)
Thermal
Shutdown
A
Low Side
LO
Driver
LS1
LS2
LS3A
OCP
OCP and OCL
FO
OCL
OCP
A IGBTs for SIM6822M and SIM6827M
Figure 1. Driver block diagram.
SIM6800M-DS
February 21, 2013
A
SANKEN ELECTRIC CO., LTD.
http://www.sanken-ele.co.jp/en/
LS3B
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
Selection Guide
Power Device Rating
Part
Number
Type
Breakdown
(V)
RDS(on) (Ω)
(Max)
Boot
Resistance
(Ω)
Input
Voltage
(VAC)
VCE(sat) (V)
Output
(A)
(Typ)
(Max)
(Typ)
SIM6811M
MOSFET
500
2.0
3.22
4.0
–
–
60
200
SIM6812M
MOSFET
500
2.5
2.0
2.4
–
–
60
200
SIM6813M
MOSFET
500
3.0
1.4
1.7
–
–
60
200
IGBT
600
5.0
–
–
1.75
2.2
60
200
SIM6822M
SIM6827M
Note
Low switching loss
Low noise
Recommended Operating Conditions
Characteristic
Main Supply Voltage
Symbol
VBB
Remarks
SIM6811M
SIM6812M
SIM6813M
Min.
Typ.
Max.
Units
–
–
400
V
–
–
400
V
13.5
15
16.5
V
Between VBB and LS
SIM6822M
SIM6827M
Logic Supply Voltage
VCC
Dead Time
tdead
1.5
–
–
μs
CBOOT
1
–
–
μF
¯¯O
¯ Pin
Pull-up Resistor ¯F
RFO
3.3
–
10
kΩ
¯¯O
¯ Pin
Capacitor ¯F
CFO
0.001
–
0.01
μF
Switching Frequency
fPWM
–
–
20
kHz
Bootstrap Capacitor
SIM6800M-DS
Between VCC and COM
SIM6822M
SIM6827M
SANKEN ELECTRIC CO., LTD.
2
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
SIM6811M, SIM6812M, and SM6813M Absolute Maximum Ratings, valid at TA = 25°C
Characteristic
Symbol
Remarks
Rating
Unit
MOSFET Breakdown Voltage
VDSS
ID = 100 μA
500
V
Logic Supply Voltage
VCC
Between VCC and COM
20
V
Bootstrap Voltage
VBS
Between VB and HS (U,V, and W phases)
20
V
SIM6811M
TC = 25°C
2.0
A
SIM6812M
TC = 25°C
2.5
A
SIM6813M
TC = 25°C
3.0
A
SIM6811M
TC = 25°C
3.0
A
SIM6812M
PW ≤ 100 μs, duty cycle = 1%
3.75
A
SIM6813M
PW ≤ 100 μs, duty cycle = 1%
4.5
A
Output Current, Continuous
Output Current, Pulsed
Input Voltage
IO
IOP
VIN
HINx, LINx, and OCP pins
Thermal Resistance (Junction to Case)
RθJC(IGBT)
All elements operating
Thermal Resistance (Junction to Ambient)
RθJA(IGBT)
All elements operating
Case Operating Temperature
TCOP
Storage Temperature
Tstg
Isolation Voltage
Viso
Between marked side of device and each pin, 1 minute, AC
–0.5 to 7
V
3.6
°C/W
25
°C/W
–20 to 100
°C
–40 to 150
°C
1500
Vrms
Rating
Unit
SIM6822M and SIM6827M Absolute Maximum Ratings, valid at TA = 25°C
Characteristic
Supply Voltage
Supply Voltage (Surge)
Symbol
Remarks
VDC
Between VBB and LS1, LS2, and LS3
450
V
VDC(Surge)
Between VBB and LS1, LS2, and LS3
500
V
IGBT Breakdown Voltage
VCES
IC = 1 mA
600
V
Logic Supply Voltage
VCC
Between VCC and COM
20
V
Bootstrap Voltage
VBS
Between VB and HS (U,V, and W phases)
20
V
5.0
A
7.5
A
Output Current, Continuous
IO
Output Current, Pulsed
IOP
PW ≤ 100 μs, duty cycle = 1%
VIN
HINx, LINx, and OCP pins
Input Voltage
Thermal Resistance (Junction to Case)
Thermal Resistance (Junction to Ambient)
Case Operating Temperature
–0.5 to 7
V
RθJC(IGBT)
IGBT, all elements operating
3.6
°C/W
RθJC(FRG)
FRG, all elements operating
4.2
°C/W
RθJA(IGBT)
IGBT, all elements operating
25
°C/W
RθJA(FRG)
FRG, all elements operating
29
°C/W
–20 to 100
°C
TCOP
Storage Temperature
Tstg
Isolation Voltage
Viso
SIM6800M-DS
Between marked side of device and each pin, 1 minute, AC
SANKEN ELECTRIC CO., LTD.
–40 to 150
°C
1500
Vrms
3
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
Typical Application Diagram
VB1A
VB1B
VB2
VB3
DC-link
15V
VBB
VCC1
UVLO
UVLO
UVLO
UVLO
A
HIN1
HIN2
HIN3
Input
Logic
A
A
High Side
Level Shift Driver
Cboot3
Cboot2
W1
W2
V
V1
V2
U
COM1
SD
VCC2
W
Controller
5V
A
Input Logic
(OCP reset)
COM2
RFO
FO
Thermal
Shutdown
A
U
A
Low Side
Driver
OCP
OCPand OCL
LS1
LS2
LS3A
LS3B
OCL
CFO
COM
Brushless
V DC motor
UVLO
LIN1
LIN2
LIN3
Cboot1
Ro
OCP
Co
RS
A MOSFETs for SIM6811M, SIM6812M and SIM6813M
NOTE:
▪ W1 and W2, as well as V1 and V2, must be externally connected to each other.
▪ If not using the Current Limiter (OCL) function, leave the OCL and SD pins open, but the SD pin should be connected to
GND if significant external noise is observed.
▪ Place a pull-up resistor, RFO , between the 3.3 V or 5 V supply and the IC, selected according to anti-noise characteristics,
even though a 1 MΩ pull-up resistor is built-in at the ¯F¯O¯ pin. Note that connecting to the 3.3 V or 5 V supply without a pull-up
resistor disables the TSD function (however, low-side UVLO protection and OCP function remain active).
▪ To avoid malfunctions resulting from noise interference, place a 0.001 to 0.01 μF ceramic capacitor (CFO) between the ¯F¯O¯
and COM2 pins.
▪ To avoid malfunctions resulting from noise interference, the traces must be as short as possible between the IC and the
bootstrap capacitors, Cbootx (approximately 1 μF).
▪ To avoid malfunctions resulting from noise interference, place a 0.01 to 0.1 μF ceramic capacitor between the VCC1 and
COM1 pins, as well as between the VCC2 and COM2 pins. Also, the traces between them must be as short as possible.
▪ To avoid malfunctions resulting from noise interference, the traces between the current sense resistor RS, which is placed
between the LS and COM2 pins, and the IC must be as short and wide as possible.
▪ To avoid malfunction, the wiring between the LS and COM2 pins should be as short as possible. When wiring cannot be
shortened sufficiently, insert a fast diode between LS and COM2.
▪ When the low pass filter (RC filter, RO, CO in the typical application circuit) is connected to the shunt resistor for current
detection, the time constant should be set to be 0.2 μs or shorter. Care should be taken because destruction of the IPM may
be caused due to detection delay when the time constant of filter is set to be 0.2 μs or longer, because a filter (1.5 μs(min)) is
incorporated in the OCP circuit of the IPM.
SIM6800M-DS
SANKEN ELECTRIC CO., LTD.
4
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
ELECTRICAL CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics
Symbol
Conditions
Min
Typ
Max
Units
Logic Supply Current
ICC
VCC = 15 V
–
3.2
4.5
mA
Bootstrap Supply Current
IBX
VBX = 15 V, VHIN = 5 V per phase
–
140
400
μA
VIH
VCC = 15 V, output on
–
2
2.5
V
VIL
VCC = 15 V, output off
1
1.5
–
V
VFOIH
VCC = 15 V, output on
–
2
2.5
V
VFOIL
VCC = 15 V, output off
1
1.5
–
V
IIH
VCC = 15 V, VIN = 5 V
–
230
500
μA
IIL
VIN = 0 V
–
–
2
μA
9.0
10.0
11.0
V
9.5
10.5
11.5
V
10.0
11.0
12.0
V
10.5
11.5
12.5
V
0
–
0.5
V
Input Voltage
¯F
¯¯O
¯ Pin Input Threshold Voltage
Input Current
VUVHL
Undervoltage Lock Out
VUVHH
VUVLL
VUVLH
¯F
¯¯O
¯ Pin Output Voltage
OCL Pin Output Voltage
VFO(L)
VFO(H)
VOCL(L)
High side, between VBx and U, V, or W
Low side, between VCC and COM
VCC = 15 V, VFO = 5 V, RFO = 10 kΩ
VCC = 15 V
4.8
–
–
V
0
–
0.5
V
4.5
–
5.5
V
Overcurrent Limit Reference Voltage
VLIM
VCC = 15 V
0.6175
0.65
0.6825
V
Overcurrent Protection Trip Voltage
VTRIP
VCC = 15 V
0.9
1.0
1.1
V
tp
VCC = 15 V
20
25
–
μs
OCP Blanking Time
tbk(OCP)
VCC = 15 V
–
2
–
μs
OCL Blanking Time
tbk(OCL)
VCC = 15 V
–
2
–
μs
135
150
165
°C
105
120
135
°C
Overcurrent Protection Hold Time
Overtemperature Detection Threshold
Temperature (Activation and
Deactivation)
VOCL(H)
TDH
TDL
VCC = 15 V, no heatsink
Bootstrap Diode Leakage Current
ILBD
VR = 500 V
–
–
10
μA
Bootstrap Diode Forward Voltage
VFBD
IF = 0.15 A
–
1.0
1.3
V
Bootstrap Diode Series Resistor
RBD
45
60
75
Ω
μA
SIM6812M and SIM6813M Switching Characteristics
MOSFET Leakage Current
MOSFET On-State Resistance
Diode Forward Voltage
IDSS
RDS(ON)
VSD
VDS = 500 V
–
–
100
SIM6811M
VCC = 15 V, ID = 1.0 A, VIN = 5 V
–
3.22
4
Ω
SIM6812M
VCC = 15 V, ID = 1.25 A, VIN = 5 V
–
2
2.4
Ω
SIM6813M
VCC = 15 V, ID = 1.5 A, VIN = 5 V
–
1.4
1.7
Ω
SIM6812M
VCC = 15 V, ID = 1.25 A, VIN = 0 V
–
1.0
1.5
V
SIM6813M
VCC = 15 V, ID = 1.5 A, VIN = 0 V
–
1.0
1.5
V
SIM6822M and SIM6827M Switching Characteristics
IGBT Leakage Current
ICES
VCC = 15 V, VCE = 600 V, VIN = 0 V
–
–
1
mA
IGBT Saturation Voltage
VCE(sat)
VCC = 15 V, IC = 5 A, VIN = 5 V
–
1.75
2.2
V
Diode Forward Voltage
VF
VCC = 15 V, ISD = 5 A, VIN = 0 V
–
2.0
2.4
V
SIM6800M-DS
SANKEN ELECTRIC CO., LTD.
5
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
SIM6811M SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics
Switching Time, High Side
Symbol
Min
Typ
Max
Units
tdH(on)
–
770
–
ns
trH
–
70
–
ns
–
150
–
ns
–
690
–
ns
trrH
Conditions
VBB = 300 V, VCC = 15 V, ID = 1.0 A, 0 V ≤ VHIN ≤ 5 V
tdH(off)
tfH
–
30
–
ns
tdL(on)
–
690
–
ns
trL
Switching Time, Low Side
–
90
–
ns
–
150
–
ns
tdL(off)
–
650
–
ns
tfL
–
50
–
ns
Min
Typ
Max
Units
tdH(on)
–
910
–
ns
trH
–
100
–
ns
–
140
–
ns
–
700
–
ns
trrL
VBB = 300 V, VCC = 15 V, ID = 1.0 A, 0 V ≤ VLIN ≤ 5 V
SIM6812M SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics
Switching Time, High Side
Symbol
trrH
Conditions
VBB = 300 V, VCC = 15 V, ID = 1.25 A, 0 V ≤ VHIN ≤ 5 V
tdH(off)
Switching Time, Low Side
tfH
–
40
–
ns
tdL(on)
–
875
–
ns
trL
–
110
–
ns
trrL
–
155
–
ns
tdL(off)
VBB = 300 V, VCC = 15 V, ID = 1.25 A, 0 V ≤ VLIN ≤ 5 V
–
775
–
ns
tfL
–
35
–
ns
Min
Typ
Max
Units
–
820
–
ns
–
100
–
ns
–
170
–
ns
–
810
–
ns
SIM6813M SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics
Symbol
Conditions
tdH(on)
trH
Switching Time, High Side
trrH
VBB = 300 V, VCC = 15 V, ID = 1.5 A, 0 V ≤ VHIN ≤ 5 V
tdH(off)
tfH
–
50
–
ns
tdL(on)
–
760
–
ns
–
130
–
ns
–
180
–
ns
tdL(off)
–
750
–
ns
tfL
–
50
–
ns
trL
Switching Time, Low Side
SIM6800M-DS
trrL
VBB = 300 V, VCC = 15 V, ID = 1.5 A, 0 V ≤ VLIN ≤ 5 V
SANKEN ELECTRIC CO., LTD.
6
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
SIM6822M SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics
Symbol
Min
Typ
Max
Units
tdH(on)
–
735
–
ns
trH
–
70
–
ns
Switching Time, High Side
trrH
Conditions
VBB = 300 V, VCC = 15 V, IC = 5 A, 0 V ≤ VHIN ≤ 5 V, inductive
load
tdH(off)
–
80
–
ns
–
570
–
ns
tfH
–
95
–
ns
tdL(on)
–
685
–
ns
–
95
–
ns
–
80
–
ns
tdL(off)
–
540
–
ns
tfL
–
95
–
ns
Min
Typ
Max
Units
–
1030
–
ns
–
180
–
ns
–
100
–
ns
–
590
–
ns
trL
Switching Time, Low Side
trrL
VBB = 300 V, VCC = 15 V, IC = 5 A, 0 V ≤ VLIN ≤ 5 V, inductive
load
SIM6827M SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics
Symbol
Conditions
tdH(on)
trH
Switching Time, High Side
trrH
VBB = 300 V, VCC = 15 V, IC = 5 A, 0 V ≤ VHIN ≤ 5 V, inductive load
tdH(off)
tfH
–
150
–
ns
tdL(on)
–
1030
–
ns
–
240
–
ns
–
100
–
ns
tdL(off)
–
540
–
ns
tfL
–
150
–
ns
trL
Switching Time, Low Side
trrL
VBB = 300 V, VCC = 15 V, IC = 5 A, 0 V ≤ VLIN ≤ 5 V, inductive load
IN
trr
t on
t d (o n )
t d (o ff)
tr
90%
VCE
IC
t o ff
10%
tf
90%
10%
Switching Time Definition
SIM6800M-DS
SANKEN ELECTRIC CO., LTD.
7
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
Truth Table
Mode
Normal
TSD
OCP
OCL1
Shown = L for
SIM682xM
(= H for SIM681xM)
UVLO ( VCC )2
UVLO ( VB )3
¯F
¯¯O
¯ ( = L)
Hin
Lin
H-side MOSFET
L-side MOSFET
L
L
Off
Off
H
L
On
Off
L
H
Off
On
H
H
On
On
L
L
Off
Off
H
L
On
Off
L
H
Off
Off
H
H
On
Off
L
L
Off
Off
H
L
On
Off
L
H
Off
Off
H
H
On
Off
Off
L (H)
L (H)
Off
H (L)
L (H)
Off
Off
L (H)
H (L)
Off
On
H (L)
H (L)
Off
On
L
L
Off
Off
H
L
Off
Off
L
H
Off
Off
H
H
Off
Off
L
L
Off
Off
H
L
Off
Off
L
H
Off
On
H
H
Off
On
L
L
Off
Off
H
L
On
Off
L
H
Off
Off
H
H
On
Off
1The
OCL feature is enabled when the OCL and SD pins are tied together externally. If these pins are not tied when an OCL
condition occurs, device operation continues in Normal mode.
2Returning to the Normal mode of operation from a V
CC UVLO condition, a high-side MOSFET resumes switching
on the rising edge of an HINx input. On the other hand, a low-side MOSFET resumes switching on the first logic high
of a LINx input after release of the UVLO condition.
3Returning to the Normal mode of operation from a V UVLO condition, a high-side MOSFET resumes switching on the rising
B
edge of an HINx input.
Note: To prevent a shoot-through condition, the external microcontroller should not drive HINx = LINx = H at the same time.
SIM6800M-DS
SANKEN ELECTRIC CO., LTD.
8
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
5V
5V
HIN
LIN
1MΩ
shut
down
2 kΩ
FO
50 Ω
20 kΩ
COM
COM
Internal equivalent circuit diagram (HIN, LIN)
SIM6800M-DS
¯¯O
¯)
Internal equivalent circuit diagram (¯F
SANKEN ELECTRIC CO., LTD.
9
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
OCP Timing Diagram
LIN
LO
(Low-side
VGATE)
OCP
VT R IP
(1V)
< 2 μs
2μs
25 μs (typ.)
FO
Low-Side TSD Timing Diagram
LO
(Low-side
VGATE)
FO
SIM6800M-DS
Open-collector output transistor
turned on in low state
SANKEN ELECTRIC CO., LTD.
10
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
High-Side UVLO Timing Diagram
(High-side
VGATE)
Low-Side UVLO Timing Diagram
LIN
VCC2
UVLH
UVLL
UVLH
LO
(Low-side
VGATE)
FO
SIM6800M-DS
Open-collector output transistor
turned on in low state
SANKEN ELECTRIC CO., LTD.
11
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
OCL Timing Diagram
(OCL and SD pins connected externally)
HIN
LIN
High-side shutdown
HO
(High-side
VGATE)
3.3 μs
3.3 μs
LO
Low-side shutdown
(Low-side
VGATE)
VTRIP (1V)
LS
VLIM
2 μs
2 μs
2 μs
OCL,
SD
20 μs(min)
FO
SIM6800M-DS
SANKEN ELECTRIC CO., LTD.
12
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
Pin-out Diagram
40
21
1
20
Pin List Table
Number
1
Name
LS3A
Function
Source pin (W phase)
2
LS2
Source pin (V phase) (optionally use pin 33)
3
OCP
Input for Overcurrent Protection
Number
Name
Function
18,22,25,
27,29,32,
34,36,
38,39
NC
Low-side logic supply voltage
19
V
High side boot-strap negative pin (V phase)
No connection (pin deleted)
4
¯F
¯¯O
¯
5
VCC2
6
COM2
Low-side logic GND pin
20
VB2
High side boot-strap positive pin (V phase)
7
LIN1
Low side input pin (U phase)
21
VB1A
High side boot-strap positive pin (U phase)
8
LIN2
Low side input pin (V phase)
22
VB3
High side boot-strap positive pin (W phase)
9
LIN3
Low side input pin (W phase)
24
W1
Output of W phase; connect to W2 externally
10
OCL
Current limiter output signal pin
26
V1
Output of V phase; connect to V2 externally
11
LS1
Source pin (U phase)
28
VBB
Main supply voltage
12
SD
Hide-side shutdown pin
30
VB1B
High side boot-strap positive pin (U phase)
13
HIN1
High-side input pin (U phase)
31
U
14
HIN2
High-side input pin (V phase)
33
LS2
Source pin (V phase); pin trimmed
15
HIN3
High-side input pin (W phase)
35
V2
Output of V-phase; connect to V1 externally
16
COM1
High-side logic GND pin
37
W2
Output of W-phase; connect to W1 externally
17
VCC1
High-side logic supply voltage
40
LS3B
SIM6800M-DS
Error signal output pin
SANKEN ELECTRIC CO., LTD.
Output of U phase
Source pin (W phase)
13
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
Package Diagram
SIM package
40
2XR1.5
21
7.6±0.4
+0.1
0.42 –0.05
1.15 MAX
Leadform 2971
20
(0.04)
33.7±0.2
17.4
(4°)
Ø3.2±0.2
1
7.4±0.15
b
8.35±0.3
Pin 1 Index
14.8±0.3
a
8.35±0.3
4X Gate area
1.8±0.1
36±0.3
0.1 S
4±0.2
+0.1
0.52 –0.05
Pin bend
exaggerated
for clarity
16.7
S
19 x P 1.778±0.25 = 33.782±0.3
1.7MIN
Unit： mm
Leadframe Material： Cu
Pin treatment: Solder Plating
：
Pb-free. Device composition compliant
with the RoHS directive.
SIM6800M-DS
a: Part #: SIM68xxM
b: Lot number 5 digits
st
1 letter: Last digit of year
nd
2 letter: Month
Jan to September: Numeric
October: O
November: N
December: D
rd
3 and 4th letter: Day
01 to 31
5th letter: Reference number
SANKEN ELECTRIC CO., LTD.
14
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
Because reliability can be affected adversely by improper storage
environments and handling methods, please observe the following
cautions.
Cautions for Storage
•
Ensure that storage conditions comply with the standard
temperature (5°C to 35°C) and the standard relative humidity
(around 40% to 75%); avoid storage locations that experience
extreme changes in temperature or humidity.
•
Avoid locations where dust or harmful gases are present and
avoid direct sunlight.
•
Reinspect for rust on leads and solderability of products that have
been stored for a long time.
Cautions for Testing and Handling
When tests are carried out during inspection testing and other
standard test periods, protect the products from power surges
from the testing device, shorts between the product pins, and
wrong connections.
Remarks About Using Silicone Grease with a Heatsink
• The screw torque for mounting a heatsink must be 58.8 to
78.4 N●cm (6.0 to 8.0 Kgf●cm). When mounting, there must
be no foreign substance between the product and the heatsink,
except for silicone grease.
• When silicone grease is used in mounting this product on a
heatsink, it shall be applied evenly and thinly. If more silicone
grease than required is applied, it may produce excess stress.
• Volatile-type silicone greases may crack after long periods of
time, resulting in reduced heat radiation effect. Silicone grease
with low consistency (hard grease) may cause cracks in the mold
resin when screwing the product to a heatsink.
SIM6800M-DS
•
Our recommended silicone greases for heat radiation purposes,
which will not cause any adverse effect on the product life, are
indicated below:
Type
Suppliers
G746
Shin-Etsu Chemical Co., Ltd.
YG6260
MOMENTIVE Performance Materials, Inc
SC102
Dow Corning Toray Co., Ltd.
Soldering
•
When soldering the products, please be sure to minimize the
working time, within the following limits:
260±5°C 10±1 s
(Flow, 2 times)
380±10°C 3.5±0.5 s (Solder iron, 1 time)
• Soldering iron should be at a distance of at least 1.5 mm from the
body of the products
Electrostatic Discharge
•
When handling the products, the operator must be grounded.
Grounded wrist straps worn should have at least 1 MΩ of
resistance from the operator to ground to prevent shock hazard,
and it should be placed near the operator.
•
Workbenches where the products are handled should be
grounded and be provided with conductive table and floor mats.
•
When using measuring equipment such as a curve tracer, the
equipment should be grounded.
•
When soldering the products, the head of soldering irons or the
solder bath must be grounded in order to prevent leak voltages
generated by them from being applied to the products.
•
The products should always be stored and transported in Sanken
shipping containers or conductive containers, or be wrapped in
aluminum foil.
SANKEN ELECTRIC CO., LTD.
15
SIM6800M Series
High Voltage 3-Phase Motor Driver ICs
Sanken reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in
the performance, reliability, or manufacturability of its products. Therefore, the user is cautioned to verify that the information in this publication is
current before placing any order.
When using the products described herein, the applicability and suitability of such products for the intended purpose shall be reviewed at the users
responsibility.
Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products
at a certain rate is inevitable.
Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems
against any possible injury, death, fires or damages to society due to device failure or malfunction.
Sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equipment or apparatus
(home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Their use in any application requiring radiation
hardness assurance (e.g., aerospace equipment) is not supported.
When considering the use of Sanken products in applications where higher reliability is required (transportation equipment and its control systems
or equipment, fire- or burglar-alarm systems, various safety devices, etc.), contact a company sales representative to discuss and obtain written
confirmation of your specifications.
The use of Sanken products without the written consent of Sanken in applications where extremely high reliability is required (aerospace equipment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited.
The information included herein is believed to be accurate and reliable. Application and operation examples described in this publication are
given for reference only and Sanken assumes no responsibility for any infringement of industrial property rights, intellectual property rights, or
any other rights of Sanken or any third party that may result from its use. The contents in this document must not be transcribed or copied without
Sanken’s written consent.
SIM6800M-DS
SANKEN ELECTRIC CO., LTD.
16