DC/DC Converter TDN 5WI Series, 5 Watt ◆ Ultra compact DIP package 0.52 x 0.36 x 0.40 inch ◆ I/O-isolation 1‘500 VDC ◆ Fully regulated outputs ◆ Operating temperature range –40°C to +75°C ◆ Short circuit protection ◆ Remote On/Off ◆ 3-year product warranty ◆ Built-in EN55022 class A filter The TDN 5WI series with 4:1 input voltage range is a selection of 5 Watt regulated dc/dc-converters. They come in a very compact DIP package (0.52 x 0.36 x 040 inch). Models Order code Input voltage Output voltage Output current max. Efficiency typ. TDN 5-2410WI 3.3 VDC 1000 mA 76 % TDN 5-2411WI 5.0 VDC 1000 mA 80 % TDN 5-2412WI TDN 5-2413WI 9 – 36 VDC TDN 5-2415WI 12 VDC 420 mA 83 % 15 VDC 333 mA 83 % 210 mA 83 % 24 VDC TDN 5-2421WI ±5.0 VDC ±500 mA 80 % TDN 5-2422WI ±12 VDC ±210 mA 83 % TDN 5-2423WI ±15 VDC ±168 mA 84 % TDN 5-4810WI 3.3 VDC 1000 mA 76 % TDN 5-4811WI 5.0 VDC 1000 mA 81 % TDN 5-4812WI Models TDN 5-4813WI 18 – 75 VDC 12 VDC 420 mA 83 % 15 VDC 333 mA 83 % TDN 5-4815WI 24 VDC 210 mA 83 % TDN 5-4821WI ±5.0 VDC ±500 mA 80 % TDN 5-4822WI ±12 VDC ±210 mA 83 % TDN 5-4823WI ±15 VDC ±168 mA 84 % http://www.tracopower.com Page 1 of 3 TDN 5WI Series, 5 Watt Input Specifications Input current no load 24 Vin models: 30 mA typ. 48 Vin models: 15 mA typ. Surge voltage (1 sec. max.) 24 Vin models: 50 V max. 48 Vin models: 100 V max. Reflected ripple current 24 Vin models: 20 mAp-p typ. 48 Vin models: 15 mAp-p typ. Input filter internal capacitor Conducted noise EN 55022 class A internal filter ESD (electrostatic discharge) EN 61000-4-2, air ±8 kV, contact ±6 kV, perf. criteria A Radiated immunity EN 61000-4-3, 10 V/m, perf. criteria A Fast transient / surge (with external input capacitor) EN 61000-4-4, ±2 kV, perf. criteria A EN 61000-4-5, ±1 kV perf. criteria A –external input capacitor all models: Nippon chemi-con KY 220µF/100V Conducted immunity EN 61000-4-6, 10 Vrms, perf. criteria A Output Specifications Voltage set accuracy ±1 % max. Voltage balance (dual output models) 1 % max. Regulation – Input variation – Load variation 0 – 100 % single output: dual output: cross regulation - dual output: 0.2 % max. 1 % max. 1 % max. (balanced load) 5 % max. (asymmetrical load 25 % / 100 %) Ripple and noise (20 MHz Bandwidth) 75 mVp-p typ. Start up time (constant resistive load) – Power ON – Remote ON 10 ms max. 10 ms max. Transient response (25% load step change) 500 μs typ. Short circuit protection continuous, automatic recovery Capacitive load –Single output –Dual output 3.3 VDC models: 4400 µF max. 5.0 VDC models: 2200 µF max. 12 VDC models: 1220 µF max. 15 VDC models: 1000 µF max. 24 VDC models: 470 µF max. ±5.0 VDC models: 1000 µF max. (each output) ±12 VDC models: 680 µF max. (each output) +15 VDC models:440 µF max. (each output) General Specifications Temperature ranges – Operating (convection cooling 20LFM, 0,1m/s) –40°C to +75°C – Case temperature +95°C max. – Storage temperature –55°C to +125°C Derating 1.8%/K above 50°C Humidity (non condensing) 95 % rel H max. Isolation voltage – I/O isolation voltage (60 sec.) 1’500 VDC Isolation capacitance (input/output) 50 pF typ. Isolation resistance (input/output) >1 Gohm Altitude during operation tbd Temperature coefficient ±0.02 %/K typ. Reliability, calculated MTBF (MIL-HDBK-217F at +25°C, ground benign) 2‘281‘000 h All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 TDN 5WI Series, 5 Watt Switching frequency 100 kHz min. Thermal shock & vibration MIL-STD-810F Remote On/Off –On: open circuit or high impedance –Off: 2 – 4 mA current applied via 1kOhm resistor –Off idle current: 2.5 mA max. Safety standards UL 60950-1 IEC/EN 60950-1 – Certification documents (pending) www.tracopower.com/overview/tdn5wi Environmental compliance – Reach www.tracopower.com/overview/tdn5wi – RoHS RoHS directive 2011/65/EU Physical Specifications Casing material non-conducting FR4 (UL 94V-0 rated) Potting material Silicone (UL 94V-0 rated) Pin material tinned copper Package weight 2.7g (0.10oz) Soldering temperature max. 260°C / 10 sec Outline Dimensions 13.2 (0.52) 9.9 (0.39) 5.07 (0.2) (3 x 0.08) 0.6 (0.024) 10.2 (0.40) 1 5 2 6 7 9.1 (0.52) 3 x 2.0 DIP package: 4 4.5 (0.18) bottom viev SMD package (on demand): (3 x 0.08) Single Dual 1 +Vin (Vcc) +Vin (Vcc) 2 –Vin (GND) –Vin (GND) 4 On/Off On/Off 5 no con. –Vout 6 –Vout Common 7 +Vout +Vout 0.6 (0.024) 13.2 (0.52) 4.8 (0.19) 1 5 2 6 7 9.1 (0.52) 3 x 2.0 Pin 14.2 (0.56) 10.2 (0.40) 9.9 (0.39) Pin-Out 4 0.25 (0.01) bottom viev Dimensions in [mm], () = Inch Tolerances: x.xx ±0.5 (±0.02) x.xxx ±0.25(±0.01) Pin pitch tolerances ±0.25 (±0.01) pin dimension tolerance ±0.1 (±0.004) Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com Rev. September 15. 2015 www.tracopower.com Page 3 of 3