Datasheet

CENTIGRID®
ESTABLISHED RELIABILITY
RELAYS
SERIES
114
ESTABLISHED RELIABILITY
DPDT
SERIES
DESIGNATION
RELAY TYPE
114
DPDT basic relay
114D
DPDT relay with internal diode for coil transient suppression
DPDT relay with internal diodes for coil transient suppression and polarity
reversal protection
114DD
INTERNAL CONSTRUCTION
DESCRIPTION
UNI-FRAME
UPPER
STATIONARY
CONTACT
ARMATURE
LOWER
STATIONARY
CONTACT
MOVING
CONTACT
ENVIRONMENTAL AND
PHYSICAL SPECIFICATIONS
Temperature
(Ambient)
–65°C to +125°C
Vibration
(General Note 1)
30 g’s to 3000 Hz
Shock
(General Note 1)
75 g’s,
6 msec, half-sine
Acceleration
50 g’s
Enclosure
Hermetically sealed
Weight
0.09 oz. (2.55g) max.
114 Page 41
The Series 114 Centigrid® relay is an ultraminiature, hermetically sealed,
armature relay. Its low profile height (.275") and .100" grid spaced terminals,
which precludes the need for spreader pads, make it ideal for applications
where extreme packaging density and/or close PC board spacing are required.
The basic design and internal construction are similar to the standard
Teledyne DPDT TO-5 relay (e.g., Series 412). The following unique
construction features and manufacturing techniques provide overall high
reliability and excellent resistance to environmental extremes:
• All welded construction.
• Unique uni-frame design providing high magnetic efficiency and mechanical
rigidity.
• High force/mass ratios for resistance to shock and vibration.
• Advanced cleaning techniques provide maximum assurance of internal
cleanliness.
• Precious metal alloy contact material with gold plating assures excellent
high current and dry circuit switching capabilities.
The Series 114D and 114DD relays have internal discrete silicon diodes for
coil suppression and polarity reversal protection.
By virtue of its inherently low intercontact capacitance and contact circuit
losses, the 114 relay has proven to be an excellent ultraminiature RF switch
for frequency ranges well into the UHF spectrum. A typical RF application for
the 114 relay is in handheld radio transceivers, wherein the combined features
of good RF performance, small size, low coil power dissipation and high
reliability make it a preferred method of Transmit-Receive
switching (see Figure 1).
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
©2003 TELEDYNE RELAYS
114/1203/Q1
SERIES 114
GENERAL ELECTRICAL SPECIFICATIONS (–65°C to +125°C unless otherwise noted) (Notes 2 & 3)
Contact Arrangement
Rated Duty
Contact Resistance
2 Form C (DPDT)
Continuous
0.1 ohm max. before life; 0.2 ohm max. after life at 1A/28Vdc (measured 1/8" from header)
Contact Load Ratings (DC)
(See Fig. 2 for other DC
resistive voltage/current ratings)
Resistive:
Inductive:
Lamp:
Low Level:
1 Amp/28Vdc
200 mA/28Vdc (320 mH)
100 mA/28Vdc
10 to 50 µA/10 to 50mV
Resistive:
250 mA/115Vac, 60 and 400 Hz (Case not grounded)
100 mA/115Vac, 60 and 400 Hz (Case grounded)
Contact Life Ratings
10,000,000 cycles (typical) at low level
1,000,000 cycles (typical) at 0.5A/28Vdc resistive
100,000 cycles min. at all other loads specified above
Contact Overload Rating
Contact Carry Rating
Operate Time
Release Time
Contact Bounce
Intercontact Capacitance
Insulation Resistance
Dielectric Strength
Negative Coil Transient (Vdc)
Diode P.I.V. (Vdc)
2A/28Vdc Resistive (100 cycles min.)
Contact factory
2.0 msec max. at nominal rated coil voltage
114 Series: 1.5 msec max. 114D, 114DD Series: 4.0 msec max.
1.5 msec max.
0.4 pf typical
10,000 megohms min. between mutually isolated terminals
Atmospheric pressure: 500 Vrms/60Hz
70,000 ft.: 125 Vrms/60Hz
114D, 114DD
1.0 max
114D, 114DD
100 min.
DETAILED ELECTRICAL SPECIFICATIONS (–65°C to +125°C unless otherwise noted) (Note 3)
BASE PART
NUMBERS
(See Note 8 for full P/N example)
Nom.
Max.
114, 114D
114DD (Note 4)
Min.
Max.
114, 114D
114DD
Min.
114, 114D
Max.
Min.
114DD
Max.
Coil Voltage (Vdc)
Coil Resistance
(Ohms ±10% @25°C)
Coil Current (mAdc @25°C)
(114DD Series)
Pick-up Voltage (Vdc, Max.)
Drop-out Voltage (Vdc)
114-5
114D-5
114DD-5
114-6
114D-6
114DD-6
114-9
114D-9
114DD-9
114-12
114D-12
114DD-12
114-18
114D-18
114DD-18
114-26
114D-26
114DD-26
5.0
5.8
50
39
93.2
128.2
3.5
4.0
0.14
2.3
0.6
2.8
6.0
8.0
98
78
58.3
78.3
4.5
5.0
0.18
3.2
0.7
3.4
9.0
12.0
220
220
33.0
42.9
6.8
7.8
0.35
4.9
0.8
5.3
12.0
16.0
390
390
25.6
32.8
9.0
10.0
0.41
6.5
0.9
6.5
18.0
24.0
880
880
17.5
22.1
13.5
14.5
0.59
10.0
1.1
10.0
26.5
32.0
1560
1560
14.8
18.5
18.0
19.0
0.89
13.0
1.4
13.0
PERFORMANCE CURVES
(NOTE 2)
TYPICAL RF PERFORMANCE
0
TYPICAL DC CONTACT RATING (RESISTIVE)
INSE
.2
LOS
300
S
.3
.4
1.92
WR)
20
RN
RETU
30
40
(VS
LOSS
1.22
1.07
CTS
50
N
ATIO
ISOL
60
ISOL
OSS
ACR
N
ATIO
TA
CON
SS
ACRO
1.02
S
POLE
1.01
1.00
70
VSWR
10
LOAD VOLTAGE (VDC)
RTIO
N
.1
dB
ESTABLISHED RELIABILITY
Contact Load Ratings (AC)
250
200
150
100
50
1.00
.01
0.5
.1
.5
1.0
0
0.1
0.2
0.3
0.4
0.5
0.6
FREQUENCY (GHz)
LOAD CURRENT (AMPS DC)
FIGURE 1
FIGURE 2
©2003 TELEDYNE RELAYS
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
0.7
0.8
0.9
1.0
114 Page 42
114/1203/Q1
SERIES 114
OUTLINE DIMENSIONS
CASE DETAIL
.375 (9.53)
SQ. MAX.
TERMINAL LOCATIONS
(Viewed from Terminals; Numbers for Reference Only)
.031 ±.003
(.79 ±.08)
.035 ±.010
(.89 ±.25)
7
8
1
.100 ±.010
(2.54 ±.25)
TYP 8 PLACES
.275 (6.99) MAX.
6
+.002 (.05)
DIA.
–.001 (.03)
114
3
4
ESTABLISHED RELIABILITY
.017 (.43)
2
5
WIRE LEAD .750 (19.05) MIN.
PIN: .187 (1.75) .010 (.25)
(See Notes 5 and 8)
SCHEMATIC DIAGRAMS
DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)
114D
GENERAL NOTES
1. Relay contacts will exhibit no chatter in excess of 10 µsec or transfer in excess of 1 µsec.
2. “Typical” characteristics are based on available data and are best estimates. No on-going
verification tests are performed.
3. Unless otherwise specified, parameters are initial values.
4. For reference only. Coil resistance not directly measurable at relay terminals due to
internal series diode. 114DD only.
5. Unless otherwise specified, relays will be supplied with either gold-plated or solder-coated
leads.
6. The slash and characters appearing after the slash are not marked on the relay.
7. Screened HI-REL versions available. Contact factory.
8.
114DD
SCHEMATICS ARE VIEWED
FROM TERMINALS
Teledyne Part Numbering System for T2R® Established Reliability Relay
ER
114 Z M4 - 26
A / S Q
Established Reliability
Designator
Q= Solder Coated Leads
G= Gold Plated Leads
(Notes 5 and 6)
Relay Series
Ground Pin Option
(See Appendix)
S= 0.187" leads
(Note 6)
Screening and Reliability
Level
Pad Option
(See Appendix)
Coil Voltage
Teledyne Part Numbering System for Military Qualified (JAN) Relays
J
114 Z
M4 - 26
P
L
Military (JAN)
Designator
Screening and Reliability
Level
Relay Series
Ground Pin Option
(See Appendix)
Terminal Variant
P = 0.187"
Coil Voltage
Pad Option
(See Appendix)
114 Page 43
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
©2003 TELEDYNE RELAYS
114/1203/Q1