OX-175 Ultra Low Noise Oven Controlled Crystal Oscillator OX-175 The OX-175 is a low phase noise, high-frequency ovenized crystal oscillator in a 28 x 38 mm package. The oscillator has a noise floor of -176dBc/Hz, and typical ADEV below 5E-12 for t=0.1 to 10 s. The OX-175 is a member of the OX-17 oscillator series. Other oscillators in the series include the OX-170 standard oscillator, OX-171 high stability oscillator, OX-172 optimized for 1588 solutions, and the OX-174 low phase noise oscillator. The Vectron design team will also help develop custom solutions where performance optimization is required for specific applications. Please contact the factory for customization options. Features Applications • Reflow Process Compatible • Temperature Stability to 50 ppb • Frequency Range 50 to 130 MHz • Standard Frequencies: 50, 60, 80, 100,120 MHz • Military Radar • Instrumentation and Test Equipment • Synthesizers • Military Communication Equipment • DRO references • Satellite Communications Performance Specifications Phase Noise Ordering Codes at 100 MHz Frequency Offset (Hz) A B C Unit Condition 10 -100 -102 -105 dBc/Hz Maximum values All EFC settings 100 -130 -132 -135 dBc/Hz 1000 -150 -156 -159 dBc/Hz 10,000 -165 -168 -170 dBc/Hz 100,000 -175 -175 -176 dBc/Hz Parameter Min Typical Max Units 2.3 3.3 4 7 3.25 5 10 10 50 10 E-12 E-12 E-12 E-12 E-11 Allan Deviation Condition 0.1 s tau 1 s tau 10 s tau 100 s tau 1000 s tau For oscillators with TDEV and MTIE requirements please review the OX-172 datasheet. Page 1 of 6 Vectron International • 267 Lowell Road, Unit 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com @ 100MHz Performance Specifications Frequency Stabilities1 (Stabilities listed for 100 MHz, for stabilities above 100 MHz values may degrade, please contact factory) Parameter Min Typical Max Units Condition vs. Operating Temperature Range (referenced to +25°C) -50 -100 +50 +100 ppb ppb -20 to +70°C -40 to +85°C vs. Supply Voltage Change vs. Load Change vs. Aging / Day vs. Aging / 1st Year vs. Aging / 10 Years -10 -10 -5 -200 -1.5 +10 +10 +5 +200 +1.5 ppb ppb ppb ppb ppm VS ±5% Load ±5% after 7 days operation after 7days operation after 7days operation Retrace2 -100 +100 ppb 5 minutes Warm-up Time to ±100ppb of final frequency ( 1 hour reading) @ +25°C Supply Voltage (Vs) Parameter Min Typical Max Units 11.4 12.0 12.6 VDC 4.5 Watts during warm-up, all temperatures 1.8 Watts steady state @ +25°C 3.3 Watts steady state @ -40°C 0.5 Watts steady state @ +85°C s time required to achieve 90% of amplitude Power Consumption Condition RF Output Start Time 1 Signal Sine Wave Load 50 Output Power +7 Ω +10 +13 dBm Harmonics -30 dBc Spurious -80 dBc Frequency Tuning (EFC) Parameter Tuning range Min Typical ±1.5 Linearity Max Units Condition ±3.0 ppm Note - each oscillator is guaranteed to have sufficient pull range for 10 years of operation 20 Tuning Slope % Positive Input Impedance Bandwidth Modulation 20 kΩ 150 Hz 0.0 10 VDC Reference Voltage Output (Vref ) 9.8 10 10.2 VDC The OX-175 series can be configured without a voltage reference. Please contact the factory for ordering information. Page 2 of 6 Vectron International • 267 Lowell Road, Unit 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Additional Parameters Parameter Min Typical g-sensitivity Max Units 1 ppb/g Condition g-sensitivity of 0.5 ppb/g available in this package size. Please contact factory for ordering information. For g-sensitivity <0.5 ppb/g please review the OX-046 series. Weight 25 g Absolute Maximum Ratings Supply Voltage (Vs) Output Load 25 Operable Temperature Range -55 15.0 VDC open Ω +95 °C Operable temperature range implies the device will continue to operate with no longterm damage to unit; however, it will not be specification compliant outside the operating temperature range Environmental and Product Classification Shock (Endurance) MIL-STD-202, Method 213, Condition J, 30g 11 ms Sine Vibration (Endurance) MIL-STD-202, Method 201 and 204, Condition A, except 5g to 500 Hz, 1 sweep each axis Random Vibration (Endurance) MIL-STD-202, Method 214, Condition I-D Humidity MIL-STD-202, Method 103, Condition B, 100% rh Seal MIL-STD-202, Method 112, Condition D, hermetic, washable Altitude MIL-STD-202, Method 105, sea level to space Resistance to Soldering Heat MIL-STD-202, Method 210, Condition A,B,C Terminal Strength MIL-STD-202, Method 211, Condition C (5 bends at 45o, 2 lbs) Moisture Sensitive Level 1 RoHS 6 (fully compliant) Storage Temperature Range -55 +125 °C Page 3 of 6 Vectron International • 267 Lowell Road, Unit 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page 4 of 6 Vectron International • 267 Lowell Road, Unit 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Outline Drawing / Enclosure Through hole Package configuration A 0 Height “H” Pin Length “L” 18.2 max 4.5 mm min Additional height options available - contact factory . Note - lower height reduces stability Pin Connections 1 Electronic Frequency Control Input (EFC) No Connect for Fixed Frequency Oscillators 2 Reference Voltage (Vref ) 3 Supply Voltage Input (Vs) 4 RF Output 5 Ground (Case) Dimensions in mm Surface mount Package configuration B 1 Height “H” Pin Length “L” 20.3 max n/a Additional height options available - contact factory . Note - lower height reduces stability Pin Connections 4,5,6,7, 11,12,13 No Connect 1 Electronic Frequency Control Input (EFC) No Connect for Fixed Frequency Oscillators 2 Reference Voltage (Vref ) 3 Supply Voltage Input (Vs) 8 RF Output 9,10 Ground (Case) Page 5 of 6 Vectron International • 267 Lowell Road, Unit 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Ordering Information3 OX - 175 0 - B E E - 107 1 - 100M000000 Product Family OX: OCXO Frequency 50M0000000 60M0000000 80M0000000 100M000000 120M000000 (others available on request) Model 175 Height and Package 0: 18.2 mm, package A - THT 1: 20 mm, package B - SMD Frequency Control 0:No Tuning, phase noise code A 1:No Tuning, phase noise code B 2:No Tuning, phase noise code C 3:Frequency Tuning, phase noise code A 4:Frequency Tuning, phase noise code B 5:Frequency Tuning, phase noise code C Supply Voltage B: 12V RF Output Code E: Sinewave Stability Code 508: ± 50 ppb 107 ± 100 ppb Temperature Range E: -40°C to +85°C J: -20°C to +70°C T: 0°C to +70°C Additional Ordering Options Additional ordering options available include custom aging rates, custom temperature ranges, custom temperature stabilities, custom phase noise requirements, improved g-sensitivity, and oscillators with no voltage reference output on pin 2. These modifications require a custom dash number - please contact the factory for additional information. Design Tools Vectron stocks the following items for small orders and prototype development: OX-1750-BEE-1075-100M00000000 Vectron stocks the following evaluation board for this product: OCXO Evaluation Board Application Notes: None Notes: 1. Unless otherwise stated, all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, and temperature (25°C). 2. Retrace is defined as the frequency difference between the end of two 24 hour on power periods with a 24 hour off period in between while at a constant temperature. 3. Not all options and codes available at all frequencies. For Additional Information, Please Contact USA: Vectron International 267 Lowell Road, Unit 102 Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 Asia: Vectron International 68 Yin Cheng Road(C), 22nd Floor One LuJiaZui Pudong, Shanghai 200120, China Tel: +86 21 6194 6886 Fax: +86 21 6194 6699 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 11-24-14 jar Page 6 of 6 Vectron International • 267 Lowell Road, Unit 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com