VX-805 Voltage Controlled Crystal Oscillator VX-805 Description The VX-805 is a Voltage Control Crystal Oscillator that operates at the fundamental frequency of the internal crystal. The crystal is a high-Q quartz device that enables the circuit to achieve low phase noise jitter performance over a wide operating temperature range. The VX-805 is housed in an industry standard hermetically sealed LCC package and is available in tape and reel. Features Applications • LVPECL output VCXO • LTE • Output Frequencies from 100 MHz to 204.8 MHz • SONET/SDH/DWDM • 3.3 V Operation • Ethernet, SyncE, GE • Fundamental Crystal Design with Low Jitter Performance • xDSL, PCMIA • Output Disable Feature • Digital Video • Excellent ±20 ppm Temperature Stability, • Broadband Access • 0/70°C, -40/85°C or -40/105°C Operating Temperature • Base Stations, Picocells • Small Industry Standard 5.0 x 3.2mm Package • Test and Measurement • Product is free of lead and compliant to EC RoHS Directive Block Diagram VDD OUT OUT E/D Gnd XTAL Vc Figure 1. Block Diagram Vectron International • 267 Lowell Road, Suite 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page1 Rev: 05/28/2015 VN Performance Specifications Table 1. Electrical Performance - 3.3V LVPECL Parameter Symbol Min Typical Max Units 3.3 3.465 V 50 90 mA 204.8 MHz Supply Voltage1 VDD Current IDD Nominal Frequency fN 2 3.135 Frequency 100 Absolute Pull Range , ordering option APR Linearity Lin 5 % Gain Transfer2 KV +80 ppm/V fSTAB ±20 ppm 2,6 2 Temperature Stability3 ±50 ppm Outputs Output Logic Levels2 Output Logic High Output Logic Low VOH VOL VDD-1.025 VDD-1.810 VDD-0.950 VDD-1.700 VDD-0.880 VDD-1.620 V V Rise Time2,4 tR 0.5 1 ns Fall Time tF 0.5 1 ns 50 50 55 60 % % 0.2 0.5 ps 2,4 Symmetry Symmetry2 (-40 °C to 105 °C) 2 Jitter, RMS 5,7 (12kHz to 20 MHz) SYM 45 40 фJ Phase Noise , 122.88MHz 10Hz 100Hz 1kHz 10kHz 100kHz 1MHz 10MHz dBc/Hz 7 -68 -98 -125 -148 -157 -157 -157 Control Voltage Control Voltage Range for Pull Range VC 0.3 Control Voltage Input Impedance ZIN 10 MΩ Control Voltage Modulation BW BW 20 kHz Output Enable/Disable8 Output Enabled, Option A Output Disabled, Option A VIH VIL 0.9*VDD Start-Up Time TS Operating Temp, Ordering Option TOP Package Size 1] 2] 3] 4] 5] 6] 7] 8] 3.0 V V 0.1*VDD 10 ms 0/70 or -40/85 or -40/105 °C 5.0 x 3.2 x 1.2 mm The power supply should have by-pass capacitors as close to the supply and to ground as possible, for examples 0.1 and 0.01uF Parameters are tested with production test circuit below as shown in Figure 2. ±20ppm temperature stability is not available for -40 °C to 105 °C temperature range Measured from 20% to 80% of a full output swing as shown in Figure 4. Not tested in production, guaranteed by design, verified at qualification. Tested with Vc = 0V to 3.3V unless otherwise stated in part description Phase Noise is measured with an Agilent E5052A Signal Source Analyzer. The Output is Enabled if the Enable/Disable is left open. Vectron International • 267 Lowell Road, Suite 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page2 Rev: 05/28/2015 VN Test Circuit Figure 2. LVPECL Test Circuit Waveform tR tF 0.8*VDD 50% 0.2*VDD On Time Period Figure 3. Output Waveform Table 2. Absolute Maximum Ratings Parameter Symbol Ratings Unit Power Supply VDD 0 to 6 V Voltage Control Range VC 0 to VDD V Storage Temperature TS -55 to 125 °C Soldering Temp/Time TLS 260 / 20 °C / sec Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this datasheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Permanent damage is also possible if OD or Vc is applied before VDD. Vectron International • 267 Lowell Road, Suite 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page3 Rev: 05/28/2015 VN Reliability VI qualification includes aging at various extreme temperatures, shock and vibration, temperature cycling, and IR reflow simulation. The VX-805 family is capable of meeting the following qualification tests: Table 3. Environmental Compliance Parameter Conditions Mechanical Shock MIL-STD-883, Method 2002 Mechanical Vibration MIL-STD-883, Method 2007 Solderability MIL-STD-883, Method 2003 Gross and Fine Leak MIL-STD-883, Method 1014 Resistance to Solvents MIL-STD-883, Method 2015 Moisture Sensitivity Level MSL 1 Contact Pads Gold over Nickel Handling Precautions Although ESD protection circuitry has been designed into the VX-805 proper precautions should be taken when handling and mounting. VI employs a human body model (HBM) and a charged device model (CDM) for ESD susceptibility testing and design protection evaluation. Table 4. ESD Ratings Model Minimum Conditions Human Body Model 500V MIL-STD-883, Method 3015 Charged Device Model 500V JESD22-C101 Parameter Symbol Value PreHeat Time Ts-min Ts-max tS 60 sec Min, 180 sec Max 150°C 200°C Ramp Up RUP 3 °C/sec Max Time Above 217 °C tL 60 sec Min, 150 sec Max Time To Peak Temperature TAMB-P 480 sec Max Table 5. Reflow Profile The device is qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements. The VX-805 device is hermetically sealed so an aqueous wash is not an issue. Termination Plating: Electroless Gold Plate over Nickel Plate Figure 4. Recommended Reflow Profile Vectron International • 267 Lowell Road, Suite 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page4 Rev: 05/28/2015 VN Outline Drawing & Pad Layout 6 5 4 VX-805 XXXMXX .126±.005 (3.2±0.13) * YYWW J1 1 2 3 1.2 Max .197±.005 (5±0.13) .035 (0.89) .025 (0.64) .079 (2.0) .039±.006 (1.0±.15) .074 (1.87) .055 (1.41) .050 (1.27) Dimensions in inches (mm) .100±.004 (2.54±.1) .015 (0.38) .050 (1.27) Figure 5. Outline Drawing and Pad Layout Table 5. Pin Out Pin Symbol Function 1 VC VCXO Control Voltage 2 E/D Enable Disable **See Ordering Options** 3 GND Case and Electrical Ground 4 Output Output 5 COutput Complementary Output 6 VDD Power Supply Voltage Tape & Reel (EIA-481-2-A) Figure 6. Tape and Reel Drawing Table 6. Tape and Reel Information Tape Dimensions (mm) Reel Dimensions (mm) Dimension W F Do Po P1 A B C D N W1 W2 Tolerance Typ Typ Typ Typ Typ Typ Min Typ Min Min Typ Max # Per Reel VX-805 16 5.5 1.5 4 8 178 1.78 13 20.6 55 12.4 22.4 500 Vectron International • 267 Lowell Road, Suite 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page5 Rev: 05/28/2015 VN Ordering Information VX-805- E C T - K X A N- 122M880000 Frequency in MHz Product VCXO, 5032 Package Other (Future Use) N: Standard Voltage Options E: +3.3 Vdc Enable / Disable A: Enable High, Pin 2 C: Enable Low, Pin 2 X: No Enable Disable Feature, Pin 2 (No Connect Internally) Stability X: Standard E: ±20 ppm Temperature Stability Output C: LVPECL Temp Range T: 0/70°C E: -40/85°C F: -40/105°C Absolute Pull Range K: ±50 ppm Example: VX-805-ECT-KXAN-122M880000 *Note: not all combination of options are available. Other specifications may be available upon request. Please consult with factory. USA: Vectron International 267 Lowell Road, Unit 102 Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 For Additional Information, Please Contact Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 7268.8010 Fax: +49 (0) 7268.801281 Asia: Vectron International 68 Yin Cheng Road (C), 22nd Floor One LuJiaZui Pudong, Shanghai 200120, China Tel: 86.21.6194.6886 Fax: 86.21.6194.6699 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Vectron International • 267 Lowell Road, Suite 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page6 Rev: 05/28/2015 VN Revision History Revision Date Approved January 21, 2015 VN Description Included Extended temperature Range of -40/105°C. Added revision history table. May 28, 2015 VN Changed maximum nominal output frequency from 250MHz to 204.8MHz Vectron International • 267 Lowell Road, Suite 102, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page7 Rev: 05/28/2015 VN