VECTRON FX-500-EAE-PNNN

FX-500
Low Jitter Frequency Translator
FX-500
Description
The FX-500 is a complete crystal-based frequency translator used in communications applications where low jitter is paramount.
Performance advantages include superior jitter performance, high output frequencies and small package size. Advanced custom
ASIC technology results in a highly robust, reliable and predictable device.
The device is packaged in a 6 pin J-Lead ceramic package with a hermetic seam welded lid.
Features
•
•
•
•
•
•
•
•
•
•
•
Applications
Complete Frequency Translator to 77.760 MHz
3.3 Volt or 5.0 Volt Supply
Capable of locking to an 8kHz pulse/ BITS clock
Tri-State Output allows board test
Lock Detect
J-lead Ceramic Package
Advanced Custom ASIC Technology
Absolute Pull Range Performance to ±100 ppm
CMOS output
Commercial or Industrial Temperature Range
EIA Compatible Tape and Reel Packaging
•
•
•
•
•
Frequency Translation, Clock Smoothing
Telecom - SONET/SDH/ATM
Datacom - DSLAM, DSLAR, Access Nodes
Cable Modem Head End
Base Station - GSM, CDMA
Block Diagram
LD
(5)
VCC
(6)
FIN
(1)
÷
Tri-State
(2)
Phase
Detector
& LD
Loop Filter
VCXO
FOUT
(4)
÷
GND
(3)
Figure 1. Functional block diagram
1 of 7
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Rev: 14Aug2009
Performance Specifications
Table 1. Electrical Performance
Parameter
Frequency
Input Frequency
Capture Range (Ordering Option)
Output Frequency
Supply 1
Voltage (Ordering Option)
Current (No Load)
Input Signal
Input Low Level Voltage
Input High Level Voltage
Pulse Width
Output 2
Output High Level Voltage
Ouput Low Level Voltage
Rise Time
Fall Time
Duty Cycle 3
≤ 60 MHz
> 60MHz
Leakage Current of Input
Loop Bandwidth (-3dB), 8kHz input
Jitter, 8kHz to 77.76MHz
rms
p-p
Symbol
Min
FIN
APR
FOUT
0.001
±50
1.0
VDD
VDD
IDD
3.0
4.5
VIL
VIH
VOH
VOL
tR
tF
D
Typical
3.3
5.0
IC
Units
77.76
±100
77.76
MHz
ppm
MHz
3.6
5.5
40
V
V
mA
0.3*VDD
V
V
ns
0.7*VDD
6
0.9*VDD
1.8
1.8
45
40
BW
Maximum
-1
0.1*VDD
3.0
3.0
V
V
ns
ns
55
60
%
%
1
μA
10
Hz
4.7
44
0.003
ps
ps
UI
1. A 0.1 μF low frequency tantalum bypass capacitor in parallel with a 0.01 μF high frequency ceramic capacitor is recommended.
2. Figure 2 defines the waveform parameters. Figure 3 illustrates the standard test conditions under which these parameters are specified and
tested.
3. Duty cycle is defined as (on time÷period), with VS = VDD/2, per figure 2. Duty cycle is measured with a 15pf load per figure 3.
4. Other frequencies may be available, please contact factory.
Figure 2. Output Waveform
2 of 7
Figure 3. Output Test Conditions (25 ± 50C )
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Rev: 14Aug2009
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at
these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to the
maximum ratings for the extended periods may adversely affect device reliability.
Table 2. Absolute Maximum Ratings
Parameter
Power Supply
Storage Temperature
Symbol
Ratings
Unit
VDD
TSTR
7
-55 to 125
V
0C
Reliability
The FX-500 is capable of meeting the following qualification tests
Table 3. Environmental Compliance
Parameter
Conditions
Mechanical Shock
Mechanical Vibration
Lead Solderability
Gross and Fine Leak
MIL-STD-883, M2002/TEST A
MIL-STD-883, M2007/TESTA
MIL-STD-883, M2003
MIL-STD-883, M1014
Handling Precautions
Although ESD protection circuitrry has been designed into the the FX-424, proper precautions should be taken when handling
and mounting. VI employs a human body model and a charged-device model (CDM) for ESD susceptibility testing and design
protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry
wide standard has been adopted for the CDM, a standard HBM of resistance=1.5Kohms and capacitance = 100pF is widely used
and therefore can be used for comparison purposes
Table 4. Predicted ESD R$atings
Model
Human Body Model
Charged Device Model
3 of 7
Minimum
1000 V
1000 V
Conditions
MIL-STD 883, Method 3015
JEDEC, JESD22-C101
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Rev: 14Aug2009
Table 5. Reflow Profile (IPC/JEDEC J-STD-020C)
Parameter
Symbol
Value
tS
60 sec Min, 180 sec Max
PreHeat Time
RUP
3 0C/sec Max
tL
60 sec Min, 150 sec Max
tAMB-P
480 sec Max
tP
20 sec Min, 40 sec Max
RDN
6 0C/sec Max
Ramp Up
Time Above 217 0C
Time To Peak Temperature
Time At 260 0C
Ramp Down
The device has been qualified to meet the JEDEC
standard for Pb-Free assembly. The temperatures
and time intervals listed are based on the PbFree small body requirements. The temperatures
refer to the topside of the package, measured on
the package body surface. The FX-500 device is
hermetically sealed so an aqueous wash is not an
issue.
Figure 4. Suggested IR Profile
Table 6. Tape and Reel Information
Tape Dimensions (mm)
Reel Dimensions (mm)
A
B
C
D
E
F
G
H
I
J
K
L
#/Reel
24
11.5
1.5
4
12
1.78
21
13
100
5
25
330
200
Figure 5. Tape and Reel
4 of 7
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Rev: 14Aug2009
FX500 YWW
CCC-CCCC
XX-XX
Y = Year
WW = Week
C = Option Codes
XX = FREQUENCY CODE
(SEE ORDERING INFO)
Inch
[mm]
Figure 6. Outline Drawing and Pad Layout
Table 7. Pin Functions
Pin #
Symbol
Function
1
fIN
Input Frequency
!
2
Tri-State
3
GND
Case and Electrical Ground
4
fo
Output Frequiency
2
5
LD
6
VDD
Logic Low = Output Disable
LOgic High = Output Enabled
Lock Detect
Power Supply Voltage
1.
Tristate is driven to logic high or logic low; there is no internal pull up or pull down resistor.
2.
LD is an open collector output requiring a 30k ohm pullup resistor to VDD. LD output is logic high under locked condition,
logic low for no input at fIN, and for “out-of-lock” condition LD transitions between logic low and logic high at the phase detector
5 of 7
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Rev: 14Aug2009
Ordering Information
Table 8. Standard Frequencies
0.0010
A1
1.0000
BB
9.2160
CH
19.6990
DK
32.7680
H3
49.1520
J7
0.0020
AR
1.0240
B2
9.7200
C8
19.7190
DH
33.0000
H7
49.4080
J2
0.0032
AG
1.2150
BU
9.7500
CE
19.9219
ED
33.3330
HC
50.0000
JD
0.0040
A2
1.2288
BK
9.8304
C1
20.0000
E2
34.3680
H6
50.0480
KD
0.0080
A3
1.2500
BG
10.0000
C4
20.1416
E3
34.5600
HB
51.2000
LL
0.0095
AU
1.3333
BF
10.2300
DP
20.4800
E4
36.8640
HG
51.8400
J4
0.0100
A6
1.5000
BE
10.2400
DM
20.5444
EF
37.0560
H4
52.0000
JP
0.0156
AL
1.5360
BV
10.4143
DV
20.7135
E1
37.1250
H9
53.3300
JU
0.0157
AD
1.5440
B3
10.4582
DU
20.8286
EB
37.5000
HK
54.7460
JL
0.0158
AC
1.9200
B1
10.4872
DN
20.8286
EG
38.8800
H5
55.0000
JX
0.0160
A4
2.0000
B8
10.9490
DG
20.9165
EH
39.0625
HH
60.0000
JR
0.0240
BX
2.0480
B4
10.9500
DJ
21.0051
EJ
39.3216
HD
61.3800
KY
0.0250
BR
2.3040
BD
11.1840
DF
22.0000
E9
39.8438
HJ
61.4400
J5
0.0320
BW
2.4576
BJ
12.2880
D8
22.1048
EK
40.0000
JF
62.2080
J8
0.0400
AP
2.5000
BM
12.3077
DY
22.2171
E5
40.2831
KK
62.5000
J9
0.0441
AA
2.5575
B9
12.3520
D1
22.5792
E8
40.9600
J1
62.9145
LE
0.0480
AB
3.0880
B6
12.8000
D2
24.0000
EC
41.0889
KM
63.3600
JJ
0.0481
AV
3.2400
BL
13.0000
D3
24.5760
E6
41.6571
KP
63.8976
JN
0.0500
BT
3.2500
BC
13.5000
DT
24.7040
E7
41.8329
KT
64.0000
JT
0.0640
A5
3.3750
BH
14.8352
DL
25.0000
F7
42.0000
JB
64.1520
JH
0.0800
A9
3.8400
B7
15.0000
D4
25.1658
F8
42.0102
KV
65.5360
J6
0.1000
AH
4.0000
BN
15.0336
DR
25.6000
F6
42.5000
JC
66.0000
JA
0.1280
AX
4.0960
B5
15.3600
DW
25.9200
F2
42.6600
JZ
70.0000
KB
0.2430
A8
5.0000
C6
16.0000
D9
26.0000
F3
44.2095
KX
70.6560
KC
0.2560
AM
5.1200
CD
16.3840
D5
27.0000
F4
44.4343
LF
71.6100
KF
0.3200
AW
6.1440
CG
17.1840
DE
27.6480
FB
44.6218
JW
73.7280
K8
0.3840
AY
6.2914
CC
18.4320
D7
28.7040
F1
44.7360
J3
74.1250
K1
0.4000
AF
6.2915
CF
18.5280
DC
29.4912
F5
44.9280
JE
74.1758
KA
0.4800
AK
6.3120
C7
18.7500
EE
29.5000
F9
45.1584
JG
74.2500
K7
0.5000
BP
6.4800
C2
19.2000
DD
30.0000
HE
45.8240
JM
75.0000
KH
0.5120
AJ
6.7500
CB
19.3927
DX
30.7200
H1
46.0379
LG
76.8000
K4
0.6555
AE
7.6800
C9
19.4400
D6
30.8800
HF
46.7200
JK
77.7600
K2
0.7720
AT
7.7760
C5
19.5313
DZ
31.2500
H8
46.8750
JY
0.9600
A7
8.1920
C3
19.6608
DB
32.0000
H2
48.0000
JV
Note 1: Other frequencies are available upon request, please contact VI for details
SS is code for non-standard frequencies, list the frequency after the part number.
Note 2: Not all combinations are possible.
Note 3: Output frequency must be equal to or greater than the input frequency. The ratio of
fo/fIN must be an integer. Also, the output frequency must be equal to greater than 100 kHz.
6 of 7
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Rev: 14Aug2009
Ordering Information
F X - 5 0 0 - E A E - K N N N - XX - XX
Output Frequency
(See Above)
Product Family
FX: Frequency Translator
Input Frequency
(See Above)
Package
500: 9.0 x 14 x 4.5 mm
Input
D: 5.0 Vdc ±10%
E: 3.3 Vdc ±10%
Performance Options
N: Standard
A: Improved Phase Noise
Output
A: CMOS
Loop Filter BW
N: Internal Loop Filter
Operating Temperature
E: -40 to 85 °C
T: 0 to 70 °C
Absolute Pull Range
K: ± 50 ppm
P: ± 80 ppm
S: ± 100 ppm
Factory Use
N: Standard
Note: Not all combinations will be availabe - check with the factory to determine the optimum configuration for your application
For Additional Information, Please Contact
USA:
Europe:
Asia:
Vectron International
267 Lowell Road
Hudson, NH 03051
Tel: 1.888.328.7661
Fax: 1.888.329.8328
Vectron International
Landstrasse, D-74924
Neckarbischofsheim, Germany
Tel: +49 (0) 3328.4784.17
Fax: +49 (0) 3328.4784.30
Vectron International
1F-2F, No 8 Workshop, No 308 Fenju Road
WaiGaoQiao Free Trade Zone
Pudong, Shanghai, China 200131
Tel: 86.21.5048.0777
Fax: 86.21.5048.1881
Disclaimer
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
7 of 7
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Rev: 14Aug2009