UNISONIC TECHNOLOGIES CO., LTD 93334

UNISONIC TECHNOLOGIES CO., LTD
93334
LINEAR INTEGRATED CIRCUIT
HIGH ENERGY IGNITION
CIRCUIT

DESCRIPTION
This device is designed to use the signal from a reluctor type
ignition pickup to produce a well controlled output from a power
darlington output transistor.
SOP-8
FEATURES

* Very Low Peripheral Component Count
* No Critical System Resistors
* Wide Supply Voltage Operating Range (4.0V ~ 24V)
* Overvoltage Shutdown (30V)
* Dwell Automatically Adjusts to Produce Optimum Stored Energy
without Waste
* Externally Adjustable Peak Current
* Transient Protected Inputs and Outputs

ORDERING INFORMATION
Note:

Ordering Number
93334G-S08-R
Pin Assignment: G: Gate
D: Drain
Package
SOP-8
Packing
Tape Reel
S: Source
MARKING
www.unisonic.com.tw
Copyright © 2014 Unisonic Technologies Co., Ltd
1 of 4
QW-R121-006.C
93334
LINEAR INTEGRATED CIRCUIT

PIN CONFIGURATION

BLOCK DIAGRAM AND TYPICAL APPLICATION
Component Values
Pickup
Coil
RL
R1, R2
C1, C2
RBAT
CFilter
CDWELL
RGAIN
RD2
RS
RDRIVE
RD1
Series resistance = 800Ω±10% @ 25℃, inductance= 1.35H @ 1.0kHz @ 15Vrms
Leakage L=0.6mH, primary R=0.43Ω±5% @ 25℃, primary L=7.5mH ~ 8.5mH @ 5.0A
Load resistor for pickup=12KΩ±20%
Input buffer resistors provide additional transient protection to the already clamped
inputs=20k±20%
For reduction of high frequency noise and spark transients induced in pick-up and leads;
optional and non-critical
Provides load dump protection (but small enough to allow operation at VBAT =4.0V) =300Ω±20%
Transient filter on VCC, non-critical
Stores reference, circuit designed for 0.1μF±20%
RGAIN/RD1 sets the DC gain of the current regulator =5.0k±20%
RD2/RD1 set up voltage feedback from RS
Sense resistor (PDAG in thick film techniques) =0.075Ω±30%
Low enough to supply drive to the output Darlington, high enough to keep VCE(SAT) of the IC
below Darlington turn-on during load dump = 100Ω±20%, 5.0W
Starting with 35Ω assures less than 5.5A, increasing as required to set 5.5A
RD1=(IO(PEAK) RS – VREF)/((VREF/RD2)-(1.4/RGAIN))-(≈100Ω)
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2 of 4
QW-R121-006.C
93334

LINEAR INTEGRATED CIRCUIT
ABSOLUTE MAXIMUM RATINGS
PARAMETER
RATINGS
UNIT
24
Power Supply Voltage-Steady State Transient 300ms or less
VCC
V
90
300
mA
Output Sink Current-Steady State Transient 300ms of less
IOUT(SINK)
1.0
A
1.05
W
Power Dissipation
PD
Derate above 25C
12
mW/C
Junction Temperature
TJ
+125
C
Operating Temperature
TOPR
-40~+125
C
Storage Temperature
TSTG
-40 ~ 150
C
Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.

SYMBOL
ELECTRICAL CHARACTERISTICS (VCC = 13.2VDC, circuit of Figure 3, unless otherwise specified)
PARAMETER
Internal Supply Voltage, Pin 6
Ignition Coil Current Peak,
Cranking RPM 2.0Hz ~ 27Hz
Ignition Coil Current Peak, Normal RPM
Ignition Coil On-Time, Normal RPM Range
Shutdown Voltage
Input Threshold (Static Test)
Input Threshold Hysteresis
Input Threshold (Active Operation)
SYMBOL TEST CONDITIONS
VBAT =4.0VDC
VBAT =8.0VDC
VCC
VBAT =12.0VDC
VBAT =14.0VDC
VBAT =4.0VDC
VBAT =6.0VDC
IPEAK
VBAT =8.0VDC
VBAT =10.0VDC
F=33Hz
F=133Hz
IPEAK F=200Hz
F=267Hz
F=333Hz
F=33Hz
F=133Hz
TON
F=200Hz
F=267Hz
F=333Hz
VBAT
Turn-on
VTHR
Turn-off
VHYS
Turn-on
VTHR
Turn-off
MIN
3.0
4.0
4.6
5.1
5.1
5.1
4.2
3.4
2.7
25
Current Limit Reference, Pin 8
VREF
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
VBAT =10VDC
VBAT =30VDC
VBAT =50VDC
120
UNIT
VDC
APEAK
APEAK
14.0
5.9
4.6
3.6
2.8
35
ms
VDC
mVDC
mVDC
1.8
1.5
60
VCE(SAT)
MAX
75
Total Circuit Lag from ts (Figure 1) until Ignition
Coil Current Falls to 10%
Ignition Coil Current Fall Time (90% ~ 10%)
Saturation Voltage IC Output (Pin 7)
(RDRIVE = 100Ω)
TYP
3.5
7.2
10.4
11.8
3.4
5.2
5.3
5.4
5.5
5.5
5.4
4.4
3.4
7.5
5.0
4.0
3.0
2.3
30
360
90
4.0
120
280
540
160
VDC
120
s
s
mVDC
190
mVDC
3 of 4
QW-R121-006.C
93334

LINEAR INTEGRATED CIRCUIT
IGNITION COIL CURRENT VS. FREQUENCY / PERIOD
IOUT (A)
6.0
5.5
5.0
VBAT =13.2VDC
VBAT -1.5V
Slope=
8.0mH
4.0
3.0
2.0
1.0
333
200
133
5
100
70
10
50
15
20
33
25
30
ms
Frequency, f (Hz)
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
4 of 4
QW-R121-006.C