AZ6962 10 AMP SUBMINIATURE POWER RELAY FEATURES • • • • • • High sensitivity, 120 mW pickup Dielectric strength 5000 Vrms Isolation spacing greater than 10 mm Proof tracking index (PTI/CTI) 250 Epoxy sealed version available Reinforced insulation, EN 60730-1 (VDE 0631, part 1) EN 60335-1 (VDE 0700, part 1) • UL, CUR file E44211 • VDE certificate 40025524 GENERAL DATA CONTACTS Arrangement SPDT (1 Form C), SPST (1 Form A, 1 Form B) Ratings Resistive load: Max. switched power: 300 W or 2500 VA Max. switched current: 10 A Max. switched voltage: 240 VDC* or 440 VAC * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 8 A 250 VAC res. Operate Time (typical) 7 ms at nominal coil voltage Release Time (typical) 3 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH See chart for VDE contact ratings on page 3. Insulation (according to DIN VDE 0110, IEC 60664-1) C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Material Silver tin oxide [1], silver nickel [2], gold plating available Dropout Greater than 10% of nominal coil voltage Resistance < 100 milliohms initially Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 85°C (185°F) Vibration Break: 0.031" (0.8 mm) DA at 10–55 Hz Make: 0.059" (1.5 mm) DA at 10–55 Hz Shock Break Contact: 5 g Make Contact: 10 g Enclosure P.B.T. polyester, UL94 V-O Terminals Tinned copper alloy, P.C. Rated Load UL, CUR VDE See chart for UL contact ratings on page 3. COIL Power At Pickup Voltage (typical) 120 mW (up to 24 VDC coil) 140 mW (48 VDC and 60 VDC coil) Max. Continuous Dissipation 1.2 W at 20°C (68°F) ambient Temperature Rise 20°C (36°F) at nominal coil voltage Max. Solder Temp. 270°C (518°F) Max. 130°C (266°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds 2. Relay may pull in with less than “Must Operate” value. Weight 8 grams 3. Specifications subject to change without notice. Packing unit in pcs 20 per plastic tube / 1000 per carton box Temperature NOTES 1. All values at 20°C (68°F). ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2015-03-31 AZ6962 RELAY ORDERING DATA COIL SPECIFICATIONS ORDER NUMBER* Nominal Coil VDC 5 Must Operate VDC 3.5 Max. Continuous VDC 11.6 Coil Resistance Ohm 113 ± 10% 1 Form A (SPST-NO) AZ6962–1AE–5D 1 Form C (SPDT) AZ6962–1CE–5D 6 4.2 14.0 9 6.3 20.8 164 ± 10% AZ6962–1AE–6D AZ6962–1CE–6D 360 ± 10% AZ6962–1AE–9D 12 8.4 27.2 AZ6962–1CE–9D 620 ± 10% AZ6962–1AE–12D AZ6962–1CE–12D 15 10.5 31.0 970 ± 10% AZ6962–1AE–15D AZ6962–1CE–15D 18 12.6 39.4 1,295 ± 10% AZ6962–1AE–18D AZ6962–1CE–18D 24 16.8 53.1 2,350 ± 10% AZ6962–1AE–24D AZ6962–1CE–24D 48 33.6 98.0 8,000 ± 15% AZ6962–1AE–48D AZ6962–1CE–48D 60 42.0 122.4 12,500 ± 15% AZ6962–1AE–60D AZ6962–1CE–60D * “1AE” or “1CE” denote silver tin oxide contacts. Substitute “1BE” in place of “1AE” or “1CE for 1 Form B relay. Substitute “1AB” or “1BB” or “1CB” in place of “1AE” or “1BE” or “1CE” for silver nickel contacts. Add suffix “E” at the end of order number for sealed version. Add suffix “A” at the end of order number for gold plated contacts. Note: 15 VDC coil is not VDE approved! MECHANICAL DATA Coil Temperature Rise FORM C VERSION 1.122 [28.5] .398 [10.1] .398 [10.1] 1.122 [28.5] .492 [12.5] .012 [0.3] .492 [12.5] .012 [0.3] .142 [3.6] 2 x ø .020 [ø 0.5] 2 x ø .020 [ø 0.5] .142 [3.6] Coil Temperature Rise °C FORM A and FORM B VERSION 2 x .016 [0.4] 2 x .031 [0.8] 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 10A 0A 60% 80% 100% 120% 140% 160% 180% 200% 220% Percent of Nominal Coil Voltage at 20°C 3 x .031 [0.8] 3 x .016 [0.4] Maximum Switching Capacity (1 Form A, 1 Form B and 1 Form C) PC BOARD LAYOUT 1 1 FORM C 2 1 2 .3 3 .2 .198 [5.04] VIEWED TOWARD TERMINALS 1000 400 500 600 700 800 900 .1 4 300 1 FORM B 2 VIEWED TOWARD TERMINALS .4 4 1 .9 .8 .7 .6 .5 200 .050 [1.3] 1.0 100 1 FORM A 1 FORM B 1 FORM A 50 60 70 80 90 .298 [7.56] .116 [2.95] .744 [18.9] 3 40 4 x ø .051 [ø 1.3] AC Resistive Load 2.0 5 30 .126 [3.2] 3.0 3 20 .126 [3.2] DC Resistive Load 4.0 .050 [1.3] 1 FORM C 9.0 8.0 7.0 6.0 5.0 4 10 .298 [7.56] 10.0 .062 [1.57] .870 [22.1] CURRENT 5 x ø .051 [ø 1.3] CIRCUIT DIAGRAM VOLTAGE Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2015-03-31 AZ6962 UL/CUR FILE E44211 APPROVED CONTACT RATING Load Type Resistive General Use MotorLoad Cycles Voltage 1 Form A 1 Form B (N.O.) (N.C.) (N.O.) 1 Form C (N.C.) Contact Material Ambient Temperature 100k 250 VAC 10 A - 10 A - [1][2] 85°C 30k 250 VAC 10 A 10 A 10 A 10 A [1][2] 85°C 30k 30 VDC 10 A 10 A 10 A 10 A [1][2] 85°C 100k 250 VAC 4A - 4A - [2] 110°C 100k 30 VDC 4A - 4A - [2] 110°C 30k 250 VDC 10 A 10 A 10 A 10 A [2] 70°C 30k 240 VAC 1/2 HP - 1/3 HP - [1][2] 85°C 30k 120 VAC 1/3 HP - 1/3 HP - [1] 85°C 1A 1A 1A 1A [2] 85°C - B300 B300 B300 B300 [1][2] 85°C - R300 R300 R300 R300 [1][2] 85°C Contact Material Ambient Temperature Pilot Duty - 30 VDC Inductive - VDE CERTIFICATE 40025524 APPROVED CONTACT RATING Load Type Resistive Inductive VDE 0631 Part 1 Inductive AC-15 Cycles Voltage 1 Form A 1 Form B 100k 250 VAC 8A 100k 250 VAC 10 A * 100k 250 VAC 1 Form C (N.O.) (N.C.) (N.O.) (N.C.) 8A - - [1][2] 85°C - - - [1] 70°C - - 8A 8A [2] 85°C 10k 250 VAC - - 8A - [1] 85°C 100k 250 VAC - - - 8A [1] 85°C 100k 250 VAC - - 10 A - [2] 85°C 50k 250 VAC 10(4) A * - - - [1] 85°C 100k 250 VAC - - [2] 85°C 100k 250 VAC - - 2(2) A [1] 85°C 100k 250 VAC - - 8(4) A [1] 85°C 30k 250 VAC - - - [1] 85°C 100k 250 VAC On: 30 A cos phi 0.7 - On: 30 A cos phi 0.7 - [1] 85°C 100k 250 VAC Off: 3 A cos phi 0.4 - Off: 3 A cos phi 0.4 - [1] 85°C 2(2) A - 2(2) A 6(4) A * with open vent hole [1] Silver tin oxide [2] Silver nickel ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2015-03-31