Inductors for Standard Circuits

I
N
D
U
C
T
O
R
S
October 2014
Inductors for Standard Circuits
Multilayer Ferrite
MLFseries
MLF1005
MLF1608
MLF2012
1005 [0402 inch]*
1608 [0603 inch]
2012 [0805 inch]
* Dimensions Code JIS[EIA]
(For automobiles)
(2/21)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20141024 / inductor_automotive_standard_mlf_en.fm
(3/21)
I
N
D
U
C
T
O
R
S
Inductors for Standard Circuits
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
AEC-Q200
Multilayer Ferrite
Overview of the MLF Series (For automobiles)
FEATURES
The lineup includes a wide inductance range.
Highly reliable monolithic structure with multilayer integration.
APPLICATION
Automotive equipment, smart phones, tablet terminals, tuners, LCD-TVs, PDP-TVs, audio equipment, computers, signal processing for
modules etc.
PART NUMBER CONSTRUCTION
MLF
Series name
1608
L×W×H Dimensions
(mm)
1005
1.0×0.5×0.5
1608
1.6×0.8×0.8
2.0×1.25×0.85
2012
2.0×1.25×1.25
A
characteristics
A
C
D
E
G
K
V
47N
△
Inductance
(μH)
0.010
10N
(10nH)
R10
0.1
1R0
1
100
10
Inductance
tolerance
J
±5%
K
±10%
M
±20%
T
D25
Packaging style
Internal code
T
Taping
D25
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Type
Temperature range
Operating
Storage
temperature
temperature
(°C)
(°C)
–55 to +125
–55 to +125
–55 to +125
–55 to +125
Package quantity
Individual weight
(pieces/reel)
(mg)
MLF1005
10,000
1.2
MLF1608
4,000
4
t=0.85
4,000
10
MLF2012
–55 to +125
–55 to +125
t=1.25
2,000
14
In case the product's inductance is 15μH or higher, both Operating and Storage temperature ranges are –40 to +85°C.
The Storage temperature range is for after the circuit board is mounted.
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(4/21)
I
N
D
U
C
T
O
R
S
Overview of the MLF Series (For automobiles)
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
30 to 60s
Peak
Temp.
Time
T4
t3
250 to 260°C 10s max.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(5/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles)
MLF1005 Type
0.50±0.05
SHAPE & DIMENSIONS
0.10min.
0.10min.
0.50±0.05
1.00±0.05
Dimensions in mm
0.5
RECOMMENDED LAND PATTERN
0.5
0.4
0.5
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(6/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF1005 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
Q
(μH)
Tolerance
min. typ.
0.10
0.12
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.39
0.47
0.56
0.68
0.82
1.0
1.2
1.5
1.8
2.2
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
10
10
15
15
15
15
15
15
15
15
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
50
55
55
55
60
60
60
60
60
60
L, Q measuring
conditions
Frequency Current
(MHz)
(mA)
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
Self-resonant
frequency(MHz)
DC resistance
(ȍ )
Rated current
(mA)
min.
typ.
max.
typ.
max.
450
400
350
320
290
260
230
210
190
170
210
190
170
150
130
120
110
100
90
80
880
800
650
600
450
450
380
330
300
250
600
460
450
360
320
290
230
200
180
150
0.51
0.59
0.63
0.72
0.79
0.91
1.05
1.35
1.50
1.95
0.41
0.42
0.47
0.55
0.59
0.64
0.79
0.95
1.05
1.30
0.33
0.33
0.39
0.40
0.47
0.65
0.80
0.89
0.95
1.35
0.24
0.25
0.34
0.43
0.43
0.45
0.55
0.68
0.75
0.99
180
180
180
160
160
150
140
130
120
120
50
50
45
45
40
40
35
35
30
30
Part No.
MLF1005VR10 △ TD25
MLF1005VR12 △ TD25
MLF1005VR15 △ TD25
MLF1005VR18 △ TD25
MLF1005VR22 △ TD25
MLF1005VR27 △ TD25
MLF1005VR33 △ TD25
MLF1005VR39 △ TD25
MLF1005VR47 △ TD25
MLF1005VR56 △ TD25
MLF1005GR39 △ TD25
MLF1005GR47 △ TD25
MLF1005GR56 △ TD25
MLF1005GR68 △ TD25
MLF1005GR82 △ TD25
MLF1005G1R0 △ TD25
MLF1005G1R2 △ TD25
MLF1005G1R5 △ TD25
MLF1005G1R8 △ TD25
MLF1005G2R2 △ TD25
The " △ " of the Part Number contains the inductance tolerance code, J (±5%), K (±10%), or M (±20%).
○ Measurement equipment
Measurement item
Product No.
L, Q
4294A+16034G
Self-resonant frequency
E4991A
DC resistance
Type-7561
* Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(7/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF1005 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
10
G1R8
G1R2
Inductance(μH)
1
GR39
GR82
GR56
VR33
VR22
0.1
VR15
VR10
VR47
0.01
1
10
100
1000
Frequency(MHz)
10
G2R2
G1R5
Inductance(μH)
GR47
G1R0
1
GR68
VR39
VR27
VR18
VR12
0.1
VR56
0.01
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(8/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF1005 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
70
60
GR39
G1R2
VR10
50
VR22
GR56
G1R8
GR82
VR47
40
Q
VR33
VR15
30
20
10
0
1
10
100
1000
Frequency(MHz)
70
G1R0
60
VR27
50
VR56
GR68
GR47
VR12
Q
40
VR18
G1R5
30
VR39
G2R2
20
10
0
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(9/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles)
MLF1608 Type
0.80±0.15
SHAPE & DIMENSIONS
0.30±0.20
0.30±0.20
0.80±0.15
1.60±0.15
Dimensions in mm
0.8
RECOMMENDED LAND PATTERN
0.6
0.8
0.6
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(10/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF1608 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
Q
(μH)
Tolerance
min. typ.
0.047
0.068
0.082
0.10
0.12
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.68
0.82
1.0
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
12
15
18
22
27
33
±20%
±20%
±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
10
10
10
15
15
15
15
15
15
15
15
15
15
15
15
35
35
35
35
35
35
35
35
35
35
35
35
30
30
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
30
30
30
30
50
50
55
55
55
55
60
60
60
60
60
60
55
55
40
40
40
40
40
L, Q measuring
conditions
Frequency Current
(MHz)
(mA)
50
1.0
50
1.0
50
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
25
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
10
1.0
4
0.1
4
0.1
4
0.1
2
0.1
2
0.1
1
0.1
1
0.1
1
0.1
1
0.1
1
0.1
Self-resonant
frequency(MHz)
DC resistance
(ȍ )
Rated current
(mA)
min.
typ.
max.
typ.
max.
600
550
500
450
400
350
320
290
260
230
210
190
170
150
130
120
110
100
90
80
70
65
60
55
45
40
35
30
25
22
20
18
15
10
900
700
650
600
550
500
450
400
350
320
290
260
230
210
190
170
150
140
130
120
110
100
90
80
70
60
55
50
45
42
40
38
35
30
0.20
0.30
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.75
0.85
0.95
1.05
1.25
1.40
0.50
0.65
0.70
0.85
1.00
1.15
1.30
1.45
1.60
1.10
1.30
1.50
1.70
1.80
1.50
1.60
1.70
1.80
2.20
0.10
0.15
0.15
0.20
0.20
0.25
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.65
0.75
0.25
0.25
0.30
0.35
0.45
0.50
0.55
0.65
0.75
0.55
0.65
0.80
1.00
1.20
0.80
0.85
0.90
1.20
1.40
200
200
200
200
200
200
150
150
150
100
100
100
100
70
70
50
50
50
50
30
30
30
30
30
15
15
10
10
10
2
2
2
2
2
Part No.
MLF1608D47N △ TD25
MLF1608D68N △ TD25
MLF1608D82N △ TD25
MLF1608DR10 △ TD25
MLF1608DR12 △ TD25
MLF1608DR15 △ TD25
MLF1608DR18 △ TD25
MLF1608DR22 △ TD25
MLF1608DR27 △ TD25
MLF1608DR33 △ TD25
MLF1608DR39 △ TD25
MLF1608DR47 △ TD25
MLF1608DR56 △ TD25
MLF1608DR68 △ TD25
MLF1608DR82 △ TD25
MLF1608A1R0 △ TD25
MLF1608A1R2 △ TD25
MLF1608A1R5 △ TD25
MLF1608A1R8 △ TD25
MLF1608A2R2 △ TD25
MLF1608A2R7 △ TD25
MLF1608A3R3 △ TD25
MLF1608A3R9 △ TD25
MLF1608A4R7 △ TD25
MLF1608E5R6 △ TD25
MLF1608E6R8 △ TD25
MLF1608E8R2 △ TD25
MLF1608E100 △ TD25
MLF1608E120 △ TD25
MLF1608C150 △ TD25
MLF1608C180 △ TD25
MLF1608C220 △ TD25
MLF1608C270 △ TD25
MLF1608C330 △ TD25
The " △ " of the Part Number contains the inductance tolerance code, J (±5%), K (±10%), or M (±20%).
○ Measurement equipment
Measurement item
Product No.
L, Q
4294A+16034G
Self-resonant frequency
E4991A
DC resistance
Type-7561
* Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(11/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF1608 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
100
E6R8
10
E100
Inductance(μH)
A4R7
A3R3
A1R0
1
A2R2
A1R5
DR68
DR47
DR33
DR22
DR15
0.1
DR10
0.01
1
10
100
1000
Frequency(MHz)
100
E120
10
E5R6
E8R2
Inductance(μH)
A3R9
A2R7
A1R2
1
A1R8
DR82
DR56
DR39
DR27
DR18
0.1
DR12
0.01
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(12/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF1608 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
100
C330
C270
Inductance(μH)
10
C220
C180
C150
1
0.1
0.1
1
10
100
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(13/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF1608 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
70
A3R3
60
A1R0
A1R5
A2R2
50
DR47
40
DR15
Q
DR22
DR33
E6R8
E100
30
DR10
20
DR68
10
0
1
10
100
1000
Frequency(MHz)
70
60
A3R9
A1R2
E8R2
50
E5R6
Q
40
E120
30
A1R8
A2R7
DR12
DR82
DR56 DR18
20
DR39
10
0
DR27
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(14/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF1608 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
70
60
50
C150
C330
40
Q
C270
30
C180
C220
20
10
0
0.1
1
10
100
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(15/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles)
MLF2012 Type
1.25±0.20
SHAPE & DIMENSIONS
0.50±0.30
0.50±0.30
T
2.00±0.20
T
0.85±0.20
1.25±0.20
Dimensions in mm
1.2
RECOMMENDED LAND PATTERN
0.8
1.0
0.8
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(16/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF2012 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
L, Q measuring
conditions
Q
(μH)
Tolerance
min. typ.
0.047
0.068
0.082
0.10
0.12
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.68
0.82
1.0
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
12
15
18
22
27
33
39
47
56
68
82
100
±20%
±20%
±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±5%±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
±10%±20%
15
15
15
20
20
20
20
20
20
20
25
25
25
25
25
45
45
45
45
45
45
45
45
45
50
50
50
50
50
30
30
30
30
30
35
35
35
25
25
25
25
25
25
30
30
30
30
30
30
30
35
35
35
35
35
55
55
60
60
60
70
70
70
70
75
75
75
75
75
45
45
45
45
45
55
55
55
45
45
45
Frequency
(MHz)
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
10
10
10
10
10
10
10
10
10
4
4
4
2
2
1
1
1
1
0.4
2
2
2
1
1
1
Current
(mA)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
Self-resonant
frequency
(MHz)
Rated
DC resistance
current
(ȍ )
(mA)
min.
typ.
max.
typ.
max.
550
500
450
400
360
320
280
250
220
200
180
160
150
140
130
120
110
100
90
80
70
60
55
50
45
40
35
30
25
22
20
18
17
15
13
11
10
9
8
7
700
600
550
500
450
410
370
330
300
270
250
230
210
190
170
160
150
140
130
120
100
90
80
70
65
60
55
50
45
40
38
35
33
28
23
20
18
16
14
12
0.10
0.15
0.15
0.10
0.12
0.13
0.15
0.16
0.18
0.23
0.25
0.25
0.30
0.35
0.40
0.15
0.15
0.18
0.20
0.22
0.25
0.28
0.30
0.35
0.60
0.65
0.70
0.80
0.90
0.70
0.80
0.90
1.00
1.10
2.40
2.70
2.80
2.90
3.00
3.10
0.05
0.08
0.08
0.10
0.20
0.20
0.20
0.30
0.30
0.40
0.40
0.50
0.50
0.60
0.60
0.30
0.30
0.40
0.40
0.50
0.50
0.60
0.60
0.70
0.30
0.32
0.35
0.40
0.50
0.35
0.38
0.45
0.50
0.55
1.30
1.60
1.80
2.00
2.40
2.50
300
300
300
300
300
300
300
250
250
250
200
200
150
150
150
80
80
80
80
50
50
50
30
30
15
15
15
15
15
5
5
5
5
5
4
4
4
2
2
2
Thickness
T
Part No.
(mm)
0.85
0.85
0.85
0.85
0.85
0.85
0.85
0.85
0.85
0.85
0.85
1.25
1.25
1.25
1.25
0.85
0.85
0.85
0.85
0.85
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
MLF2012D47N △ TD25
MLF2012D68N △ TD25
MLF2012D82N △ TD25
MLF2012DR10 △ TD25
MLF2012DR12 △ TD25
MLF2012DR15 △ TD25
MLF2012DR18 △ TD25
MLF2012DR22 △ TD25
MLF2012DR27 △ TD25
MLF2012DR33 △ TD25
MLF2012DR39 △ TD25
MLF2012DR47 △ TD25
MLF2012DR56 △ TD25
MLF2012DR68 △ TD25
MLF2012DR82 △ TD25
MLF2012A1R0 △ TD25
MLF2012A1R2 △ TD25
MLF2012A1R5 △ TD25
MLF2012A1R8 △ TD25
MLF2012A2R2 △ TD25
MLF2012A2R7 △ TD25
MLF2012A3R3 △ TD25
MLF2012A3R9 △ TD25
MLF2012A4R7 △ TD25
MLF2012E5R6 △ TD25
MLF2012E6R8 △ TD25
MLF2012E8R2 △ TD25
MLF2012E100 △ TD25
MLF2012E120 △ TD25
MLF2012C150 △ TD25
MLF2012C180 △ TD25
MLF2012C220 △ TD25
MLF2012C270 △ TD25
MLF2012C330 △ TD25
MLF2012K390 △ TD25
MLF2012K470 △ TD25
MLF2012K560 △ TD25
MLF2012C680 △ TD25
MLF2012C820 △ TD25
MLF2012C101 △ TD25
The " △ " of the Part Number contains the inductance tolerance code, J (±5%), K (±10%), or M (±20%).
○ Measurement equipment
Measurement item
Product No.
L, Q
4294A+16034G
Self-resonant frequency
E4991A
DC resistance
Type-7561
* Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(17/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
100
E100
10
A4R7
Inductance(μH)
E6R8
A1R0
1
A3R3
A2R2
A1R5
DR68
DR47
DR33
DR22
DR15
0.1
DR10
0.01
1
10
100
1000
Frequency(MHz)
100
E120
10
E8R2
A3R9
Inductance(μH)
E5R6
DR82
A2R7
A1R8
DR56
A1R2
1
DR39
DR27
DR18
0.1
DR12
0.01
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(18/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
100
C680
C101
C820
K470
K390
10
Inductance(μH)
K560
C270
C220
C330
C150
1
C180
0.1
0.1
1
10
100
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(19/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF2012 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
90
A4R7
80
A3R3
70
A2R2
A1R5
E100
60
DR22
DR15
E6R8
DR33
Q
50
A1R0
40
DR47
DR10
30
DR68
20
10
0
1
10
100
1000
Frequency(MHz)
90
80
E5R6
E8R2
A3R9
A2R7
70
E120
60
Q
DR18
DR39
A1R8
50
A1R2
DR12
40
DR82
30
DR56
20
DR27
10
0
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(20/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles) MLF2012 Type
Q FREQUENCY CHARACTERISTICS GRAPH
90
80
70
K470
60
C330
50
C270
Q
C180
K390
40
K560
C101
C220
30
C680
C820
20
C150
10
0
0.1
1
10
100
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm
(21/21)
I
N
D
U
C
T
O
R
S
MLF series (For automobiles)
Packaging Style
REEL DIMENSIONS
ø60min.
1.0
2.0±0.5
8.4 +2.0
–0.0
ø13±0.2
14.4max.
ø21±0.8
ø180±2.0
Dimensions in mm
3.5±0.05
Cavity
Type
MLF1005
MLF1608
t=0.85
MLF2012
t=1.25
A
1.15±0.1
1.9±0.2
2.3±0.2
2.3±0.2
B
0.65±0.1
1.1±0.2
1.5±0.2
1.5±0.2
K
0.8 max.
1.1 max.
1.1 max.
1.5 max.
A
8.0±0.3
Sprocket hole
1.5 +0.1
–0.0
1.75±0.1
TAPE DIMENSIONS
K
B
4.0±0.1
2.0±0.05
160min.
Drawing direction
Taping
2.0±0.05
200min.
300min.
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20141024 / inductor_automotive_standard_mlf_en.fm