E M C C o m p o n e n t s July 2014 Common Mode Filters For automotive power line ACM-V series ACM4520V ACM70V ACM90V ACM12V (2/13) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-02 / 20140717 / e9713_acm_v.fm (3/13) E M C C o m p o n e n t s Common Mode Filters Product compatible with RoHS directive Halogen-free Compatible with lead-free solders AEC-Q200 For automotive power line Overview of the ACM-V Series FEATURES Exclusive square type closed magnetic core designed as an exclusive core is used, so it can be small while maintaining the same features. Low profile design makes it optimal for surface mounting. Excellent impedance characteristics, making it great for suppressing common mode noise. Series includes large current products up to 8A, making them compatible with various DC power lines. Covers a wide operating temperature range from –40 to +125°C. APPLICATION Common mode noise countermeasure for electronic controller DC power lines and power supply lines for car multi-media equipment and various electronic devices. PART NUMBER CONSTRUCTION ACM Series name 90V - L×W×H Dimensions (mm) 4520V 4.7×4.5×2.0 70V 7.0×6.0×3.5 90V 9.0×7.0×4.5 12V 12.0×11.0×6.0 701 - Impedance (:) at 100MHz 701 700 2PL - TL Number of lines 2P 2PL 2 lines 2 lines - □□□ Packaging style T TL Internal code ø180mm reel ø330mm reel OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type ACM4520V Temperature range Operating Storage temperature temperature （°C） （°C） –40 to +125 –40 to +125 ACM70V –40 to +125 –40 to +125 ACM90V –40 to +125 –40 to +125 ACM12V –40 to +125 –40 to +125 The Storage temperature range is for after the circuit board is mounted. Reel diameter Package quantity Individual weight （mm） ø180 ø330 ø330 ø330 ø330 （pieces/reel） 800 2,500 1,500 800 500 （g） 0.15 0.35 0.82 2.3 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (4/13) E M C C o m p o n e n t s Overview of the ACM-V Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 10 to 30s Peak Temp. T4 245°C Time t3 5s • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (5/13) E M C C o m p o n e n t s ACM-V series ACM4520V Type SHAPE & DIMENSIONS 4.7±0.2 4.5 4 2 3 4.5±0.2 1 Ferrite 0.65 2.0max. 0.65 Wire 0.75 0.75 2.0 Dimensions in mm RECOMMENDED LAND PATTERN 3.5 1.25 2.0 0.95 1.05 0.95 1.25 CIRCUIT DIAGRAM 1 4 2 3 • No polarity Dimensions in mm • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (6/13) E M C C o m p o n e n t s ACM-V series ACM4520V Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [at 100MHz] min. typ. 180 230 300 420 650 900 1000 1400 Rated current (A)max. 125°C 1.5 1.4 1.2 1.0 DC resistance (: )max. [1 line] 0.05 0.055 0.06 0.08 ○ Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A ＊ Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 10 10 10 Rated voltage (V)max. 50 50 50 50 Part No. ACM4520V-231-2P-TL□□□ ACM4520V-421-2P-TL□□□ ACM4520V-901-2P-TL□□□ ACM4520V-142-2P-TL□□□ Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 142 Common mode 1000 Impedance (Ω) 901 Common mode 421 Common mode 421 Differential mode 100 231 Differential mode 901 Differential mode 1 142 Differential mode 231 Common mode 10 1 10 100 1000 Frequency (MHz) ○ Measurement equipment Product No. Manufacturer 4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (7/13) E M C C o m p o n e n t s ACM-V series ACM70V Type SHAPE & DIMENSIONS 7.0±0.2 4 2 3 6.0±0.2 1 4.0typ. 1.5±0.2 3.5max. 1.5±0.2 1.5±0.2 1.5±0.2 1.5±0.2 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 9.0 1.5 4.0 2 3 1 4 3.0 • No polarity Dimensions in mm • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (8/13) E M C C o m p o n e n t s ACM-V series ACM70V Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [at 100MHz] min. typ. 500 700 DC resistance (m: )max. Rated current (A)max. Rated voltage (V)max. 15 4.0 80 ○ Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A ＊ Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 Part No. ACM70V-701-2PL-TL00 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 1000 Impedance (Ω) 701 Common mode 701 Differential mode 100 10 1 1 10 100 1000 Frequency (MHz) ○ Measurement equipment Product No. Manufacturer 4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (9/13) E M C C o m p o n e n t s ACM-V series ACM90V Type SHAPE & DIMENSIONS 9.0±0.2 4 2 3 7.0±0.2 1 6.0typ. 1.5±0.2 4.5max. 1.5±0.2 1.5±0.2 1.5±0.2 2.0±0.2 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 11.0 1.5 6.0 2 3 1 4 3.5 • No polarity Dimensions in mm • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (10/13) E M C C o m p o n e n t s ACM-V series ACM90V Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [at 100MHz] min. typ. 500 700 DC resistance (m: )max. Rated current (A)max. Rated voltage (V)max. 10 5.0 80 ○ Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A ＊ Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 Part No. ACM90V-701-2PL-TL00 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 1000 Impedance (Ω) 701 Common mode 701 Differential mode 100 10 1 1 10 100 1000 Frequency (MHz) ○ Measurement equipment Product No. Manufacturer 4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (11/13) E M C C o m p o n e n t s ACM-V series ACM12V Type SHAPE & DIMENSIONS 12.0±0.3 4 2 3 11.0±0.3 1 7.4typ. 2.3±0.2 6.0max. 2.3±0.2 2.7±0.2 2.7±0.2 2.5±0.2 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 14.0 2.7 7.6typ. 2 3 1 4 5.2 • No polarity Dimensions in mm • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (12/13) E M C C o m p o n e n t s ACM-V series ACM12V Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance (: ) [at 100MHz] min. typ. 500 700 DC resistance (m: )max. Rated current (A)max. Rated voltage (V)max. 6 8.0 80 ○ Measurement equipment Measurement item Product No. Common mode impedance 4991A DC resistance 4338A Insulation resistance 4339A ＊ Equivalent measurement equipment may be used. Insulation resistance (M: )min. 10 Part No. ACM12V-701-2PL-TL00 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 Impedance (Ω) 1000 701 Common mode 701 Differential mode 100 10 1 1 10 100 1000 Frequency (MHz) ○ Measurement equipment Product No. Manufacturer 4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm (13/13) E M C C o m p o n e n t s ACM-V series Packaging style REEL DIMENSIONS 2.0±0.5 E Type ACM4520V N 100±1 60+1/–0 100±1 100±1 100±1 E 2 typ. 2 typ. 2 typ. 2 typ. 2 typ. N ACM70V ACM90V ACM12V A W1 W2 ø330±2 13.5±0.5 17.5±1 ø180±3 13±0.3 17±1.4 ø330±2 16.4+2/–0 20.4 typ. ø330±2 16.4+2/–0 20.4 typ. ø330±2 24.4+2/–0 28.4 typ. 1.0 ø13.0±0.2 W1 ø21.0±0.8 W2 A Dimensions in mm TAPE DIMENSIONS P0 t B W F P2 E øD0 A K P1 Dimensions in mm Type ACM4520V ACM70V ACM90V ACM12V A 4.75±0.1 6.6±0.1 8.6±0.1 13.2±0.1 B 5.05±0.1 7.6±0.1 9.6±0.1 13.5±0.1 øD0 1.55+0.1/0 1.5+0.1/0 1.5+0.1/0 1.5+0.1/0 E 1.75±0.1 1.75±0.1 1.75±0.1 1.75±0.1 F 5.5±0.05 7.5±0.1 7.5±0.1 11.5±0.1 P0 4.0±0.1 4.0±0.1 4.0±0.1 4.0±0.1 P1 8.0±0.1 8.0±0.1 12.0±0.1 16.0±0.1 P2 2.0±0.05 2.0±0.1 2.0±0.1 2.0±0.1 W 12.0±0.2 16.0±0.3 16.0±0.3 24.0±0.3 K 2.05±0.05 3.6±0.1 4.6±0.1 6.4±0.1 t 0.3±0.1 0.4±0.05 0.4±0.05 0.5±0.05 500 to 560min. 160min. Taping L Drawing direction Type ACM4520V ACM70V ACM90V ACM12V L 100 to 200 440min. 440min. 440min. Dimensions in mm • All specifications are subject to change without notice. 001-02 / 20140717 / e9713_acm_v.fm