SP8910 (MP) 5GHZ ÷ 10 Fixed Modulus Divider Data Sheet January 2008 DS4360 The SP8910 is one of a range of very high speed low power prescalers for professional applications. The dividing elements are static D type flip flops and therefore allow operation down to DC if the drive signal is a pulse waveform with fast risetime. The output stage has internal100 ohm pull up resistors, giving a 0·5V p-p output. If required, an external 100 ohm can be connected in parallel to give a 50 ohm output. Ordering Information SP8910/KG/MP1S SP8910/KG/MP1T SP8910/KG/MP2P Tubes Tape & Reel Tubes, Bake & Drypack* Tape & Reel, SP8910/KG/MP2Q Bake & Drypack* *Pb Free Tin/Silver/Copper Features Absolute Maximum Ratings • Very High Operating Speed • Operation down to DC with Square Wave Input • Silicon Technology for Low Phase Noise (Typically better than 2140dBc/Hz at 1KHz) • 5V Single Supply Operation • Low Power Dissipation: 340mW (Typ.) • Surface Mount Plastic Package Supply voltage, VCC 6·5V Storage temperature 265°C to 1150°C Maximum junction temperature 1150°C Prescaler input voltage 2·5Vp-p Operating temperature KG240°C to 185°C TCASE VCC OUTPUT VCC 1 8 100 100 7 6 OUTPUT OUTPUT VREF 45 400 INPUT INPUT 42 400 2 5mA 3 4 4 GND Figure 1 - block diagram 1 Zarlink Semiconductor Inc. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 1999-2008, Zarlink Semiconductor Inc. All Rights Reserved. SP8910 Data Sheet VCC 1 8 OUTPUT VCC INPUT 2 7 OUTPUT INPUT 3 6 OUTPUT GND 4 5 GND SP8910 MP8 Figure 2 - Pin connections - top view Electrical Characteristics These characteristics are guaranteed by either production test or design over the following range of operating conditions unless otherwise stated: TAMB = 240°C to 185°C, VCC = 4·75V to 5·25V Value Characteristic Pin 1, 8 2, 3 2, 3 2, 3 2, 3 2, 3 2, 3 6, 7 6, 7 Supply current Input frequency Input frequency Input sensitivity Input sensitivity Input overload Input overload Output voltage Output power Min. Typ. Max. 1·0 1·0 440 700 218·0 68 - 92 5·0 5·5 180 570 24·0 0·25 29·0 Units Conditions mA GHz GHz mVrms mVrms mVrms mVrms Vp-p dBm RMS sinewave RMS sinewave, TCASE = 255°C to 185°C fIN = 1GHz and 4.2GHz fIN = 5GHz fIN = 1GHz and 3GHz fIN = 5.0GHz and 3.8GHz Into 100Ω pullup resistor fIN = 1GHz and 5GHz (see note 1 ) NOTE 1. Measured into 50Ω measuring instrument in parallel with 100Ω pullup resistor. See Figure 5. VIN INTO 50Ω (mV RMS) 800 600 TESTED AS PER TABLE OF ELECTRICAL CHARACTERISTICS 400 OPERATING WINDOW 200 1 2 3 4 5 FREQUENCY (GHz) Figure 3 - Typical input sensitiviy (sinewave drive) 2 6 7 SP8910 Data Sheet VCC 15V SIGNAL GENERATOR 2 100 8 1 1n SP8910 100 1n 7 3 6 4 5 50Ω MEASURING INSTRUMENT 1n 10n 1n 10n Figure 4 - Typical application and test circuit j1 j0.5 j2 3GHz j0.2 5GHz 0 0.2 0.5 1 2 j5 5 0·3GHz 1GHz 2j5 2j0.2 2j2 2j0.5 2j1 Figure 5 - Typical input impedance 3 4 Figure 6 - Typical phase noise, input frequency = 3GHz 10 2 170 2 160 2 150 2 140 2 130 2 120 2 110 2 100 2 90 2 80 2 70 2 60 2 50 2 40 2 30 2 20 2 10 0 100 1k FREQUENCY (Hz) 10k 100k SP8910 Data Sheet L(f) [dBc/Hz] For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL, the Zarlink Semiconductor logo and the Legerity logo and combinations thereof, VoiceEdge, VoicePort, SLAC, ISLIC, ISLAC and VoicePath are trademarks of Zarlink Semiconductor Inc. TECHNICAL DOCUMENTATION - NOT FOR RESALE