Through-hole resistors HID Lamp Type HID Lamp Resistors Metal Film Style [ HTM Series ] Carbon Film Style [ HTR Series ] FEATURES Power Rating 2W, 2.5W Resistance Tolerance ±5% T.C.R. ±250ppm/°C, -500~350ppm/°C INTRODUCTION The HTM Series Metal Film Resistors are manufactured using a vacuum sputtering system to deposit multiple layers of mixed metal alloys onto a carefully treated high grade ceramic substrate. And the HTR Series Carbon Film Resistors are manufactured by coating a homogeneous film of pure carbon on high grade ceramic rods. After a helical groove has been cut in the resistive layer, steel copper plated wires are welded to the end-caps. The resistor is not coated. This is a special product for HID lamps, providing high power within a small package and saving space. DIMENSIONS Unit: mm ød H L øD STYLE DIMENSION Normal L øD H ød HTR200 8.5±0.3 3.5±0.2 26±2.0 0.8±0.05 HTM200 8.5±0.3 3.5±0.2 26±2.0 0.8±0.05 HTM250 15.5±0.3 3.5±0.2 33±2.0 0.8±0.05 19 Note: ELECTRICAL CHARACTERISTICS STYLE HTR200 Power Rating at 70°C 2W HTM200 HTM250 2.5W PxR Maximum Working Voltage Resistance Range 2KΩ - 100KΩ for E24 series value Temperature Coefficient ±250ppm/°C for HTM series, -500~+350ppm/°C for HTR series Note: Special value is available on request ENVIRONMENTAL CHARACTERISTICS PERFORMANCE TEST TEST METHOD APPRAISE Short Time Overload IEC 60115-1 4.13 2.5 times RCWV for 5 Sec. ±0.25% for HTM series ±0.50% for HTR series Temperature Coefficient IEC 60115-1 4.8 -55°C to +155°C By type Robustness of Terminations IEC 60115-1 4.16 Direct load for 10 Sec. in the direction of the terminal leads ≥4kg (39.2N) Periodic-pulse Overload IEC 60115-1 4.39 4 times RCWV 10,000 cycles (1 Sec. on, 25 Sec. off) ±1.0%+0.05Ω Endurance at 70°C IEC 60115-1 4.25 70±2°C at RCWV for 1,000 Hr. (1.5 Hr. on, 0.5 Hr. off) ±1.5%+0.05Ω Temperature Cycling IEC 60115-1 4.19 -55°C Room Temp. +155°C Room Temp. (5 cycles) ±0.75%+0.05Ω Note: RCWV(Rated Continuous Working Voltage) = Power Rating x Resistance Value or Max. working voltage listed above, whichever less. Revision: 201304 88 Explanations Of Ordering Code MFR -12 F Code 7 Tolerance T F Code 8 Packing Style Code 9 Temperature Coefficient of Resistance Code 1 - 3 Series Name Code 4 - 6 Power Rating See Index -05= ød0.5mm P= ±0.02 % T = Tape/Box -06 = ød0.6mm A= ±0.05 % R = Tape/Reel - = Base on Spec. -07 = ød0.7mm B= ±0.1 % B = Bulk 52- 100R Code 10 - 12 Forming Type Code 13 - 17 Resistance Value 26- = 26mm 0R1=0.1 52- = 52.4mm 100R=100 A = ±5 ppm/°C 73- = 73mm 10K=10,000 81- = 81mm 10M=10,000,000 -08 = ød0.8mm C= ±0.25% B = ±10 ppm/°C -10 = ød1.0mm D= ±0.5 % C = ±15 ppm/°C 91- = 91mm -14 = ød1.4mm F = ±1 % S = ± 20ppm/°C F = F Type -12 = 1/6W G= ±2 % D = ±25 ppm/°C FK = FK Type -25 = 1/4W J = ±5 % E = ±50 ppm/°C FKK= FKK Type 25S = 1/4WS K= ±10 % F = ±100 ppm/°C FFK= F-form Kink -50 = 1/2W - = Base on Spec. G = ±200 ppm/°C M = M-Type Forming 50S = 1/2WS H = ±250 ppm/°C MB = M-form W/flat 100 = 1W I = ±300 ppm/°C MT = MT Type Forming 1WS = 1WS J = ±350 ppm/°C MR = MR Type 200 = 2W AV = AVIsert 2WS = 2WS PN = PANAsert 204 = 0.4W 207 = 0.6W 300 = 3W 3WS = 3WS 3WM= 3WM 400 = 4W 500 = 5W 5WS = 5WS 5SS = 5WSS 700 = 7W 7WS = 7WS 10A = 10W 20A = 20W 30A = 30W 40A = 40W 50A = 50W 10S = 10WS 15A = 15W 25A= 25W 10B = 100W 25B = 250W EXCEPTION: • Cement series: • JPW series: <Code 8>: Special packing style code B: B ulk with wirewound or metal oxide sub-assembly for resistance value W: Bulk with ceramic based wirewound sub-assembly for resistance value M: Bulk with metal oxide sub-assembly for resistance value F: Bulk with Fiberglass based wirewound sub-assembly for resistance value <Code 10-12>: Without forming code Example: SQP500JB-10R <Code 13-17>: without resistance value code Example: JPW-06-T-52-