Through-hole resistors Low Ohmic Wire Resistors Alloy-Wire Type Normal Style [ MCW Series ] FEATURES Material Manganese-copper, Nickel-copper, others upon request Resistance Tolerance ±2%, ±5% T.C.R. ±50ppm/°C, ±100ppm/°C, ±200ppm/°C INTRODUCTION •The Low Ohmic Alloy-Wire Resistors are suitable for high power current detection, it is non-inductive type •Low Ohmic Wire Resistors meet EU-RoHS requirements DIMENSIONS Unit: mm L L H øD P C øD Max 0.5 Max 0.5 STYLE DIMENSION Normal øD C H MCW-06 0.6±0.02 0.9±0.1 3.0±0.5 MCW-08 0.8±0.02 1.1±0.1 3.0±0.5 MCW-10 1.0±0.02 1.3±0.1 3.0±0.5 MCW-12 1.2±0.02 1.5±0.1 3.0±0.5 MCW-14 1.4±0.02 1.7±0.1 3.0±0.5 MCW-16 1.6±0.02 1.9±0.2 3.0±0.5 MCW-18 1.8±0.02 2.2±0.2 3.0±0.5 MCW-20 2.0±0.02 2.5±0.2 3.0±0.5 MCW-26 2.6±0.02 3.2±0.2 3.0±0.5 P, L P L L H H C øD p Max 0.5 Max 0.5 P L H C øD p C øD M-Type K-Type W-Type B-Type N-Type Max 0.5 P & L could be designed by customer's requirement 47 Note: ELECTRICAL CHARACTERISTICS STYLE MCW-06 MCW-08 MCW-10 MCW-12 MCW-14 MCW-16 MCW-18 MCW-20 MCW-26 Maximum Current Rating 3A 4.5A 5.5A 7.0A 8.0A 9.5A 11A 12A 18A Resistance Range 0.0014Ω - 0.078Ω Operating Temp. Range -40°C to +170°C Temperature Coefficient ±50ppm/°C, ±100ppm/°C, ±200ppm/°C Note: Below or over this resistance value is available on request ENVIRONMENTAL CHARACTERISTICS PERFORMANCE TEST TEST METHOD APPRAISE Short Time Overload IEC 60115-1 4.13 2.5 times RCWV for 5 Sec. ±2% Temperature Coefficient IEC 60115-1 4.8 -55°C to +125°C By type Solderability IEC 60115-1 4.17 235±5°C for 3±0.5 Sec. 95% Min. coverage Damp Heat Steady State IEC 60115-1 4.24 40±2°C, 90-95% RH for 56 days, loaded with 0.1 times RCWV ±2.0% Endurance at 70°C IEC 60115-1 4.25 70±2°C at RCWV for 1,000 Hr. (1.5 Hr. on, 0.5 Hr. off) ±3.0% Temperature Cycling IEC 60115-1 4.19-55°C Room Temp. +155°C Room Temp. (5 cycles) ±1.0% Resistance to Soldering Heat IEC 60115-1 4.18 ±1.0% 260±3°C for 10±1 Sec., immersed to a point 3±0.5mm from the body Note: RCWV(Rated Continuous Working Voltage) = Power Rating x Resistance Value or Max. working voltage listed above, whichever less. Revision: 201304 88 Explanations Of Ordering Code MFR -12 F Code 7 Tolerance T F Code 8 Packing Style Code 9 Temperature Coefficient of Resistance Code 1 - 3 Series Name Code 4 - 6 Power Rating See Index -05= ød0.5mm P= ±0.02 % T = Tape/Box -06 = ød0.6mm A= ±0.05 % R = Tape/Reel - = Base on Spec. -07 = ød0.7mm B= ±0.1 % B = Bulk 52- 100R Code 10 - 12 Forming Type Code 13 - 17 Resistance Value 26- = 26mm 0R1=0.1 52- = 52.4mm 100R=100 A = ±5 ppm/°C 73- = 73mm 10K=10,000 81- = 81mm 10M=10,000,000 -08 = ød0.8mm C= ±0.25% B = ±10 ppm/°C -10 = ød1.0mm D= ±0.5 % C = ±15 ppm/°C 91- = 91mm -14 = ød1.4mm F = ±1 % S = ± 20ppm/°C F = F Type -12 = 1/6W G= ±2 % D = ±25 ppm/°C FK = FK Type -25 = 1/4W J = ±5 % E = ±50 ppm/°C FKK= FKK Type 25S = 1/4WS K= ±10 % F = ±100 ppm/°C FFK= F-form Kink -50 = 1/2W - = Base on Spec. G = ±200 ppm/°C M = M-Type Forming 50S = 1/2WS H = ±250 ppm/°C MB = M-form W/flat 100 = 1W I = ±300 ppm/°C MT = MT Type Forming 1WS = 1WS J = ±350 ppm/°C MR = MR Type 200 = 2W AV = AVIsert 2WS = 2WS PN = PANAsert 204 = 0.4W 207 = 0.6W 300 = 3W 3WS = 3WS 3WM= 3WM 400 = 4W 500 = 5W 5WS = 5WS 5SS = 5WSS 700 = 7W 7WS = 7WS 10A = 10W 20A = 20W 30A = 30W 40A = 40W 50A = 50W 10S = 10WS 15A = 15W 25A= 25W 10B = 100W 25B = 250W EXCEPTION: • Cement series: • JPW series: <Code 8>: Special packing style code B: B ulk with wirewound or metal oxide sub-assembly for resistance value W: Bulk with ceramic based wirewound sub-assembly for resistance value M: Bulk with metal oxide sub-assembly for resistance value F: Bulk with Fiberglass based wirewound sub-assembly for resistance value <Code 10-12>: Without forming code Example: SQP500JB-10R <Code 13-17>: without resistance value code Example: JPW-06-T-52-