F12A20CT thru F12A60CT Pb F12A20CT thru F12A60CT 12.0 Ampere Common Anode Fast Recovery Rectifier Diodes Unit : inch (mm) TO-220AB Feature Fast switching for high efficiency Low forward voltage drop High current capability Low reverse leakage current High surge current capability .419(10.66) .387(9.85) .196(5.00) .163(4.16) .139(3.55) MIN .054(1.39) .624(15.87) .177(4.5)MAX Automotive Environment(Inverters/Converters) Plating Power Supply,Adaptor,SMPS and UPS Car Audio Amplifiers and Sound Device System .038(0.96) .019(0.50) Mechanical Data Case:TO-220AB Heatsink Epoxy: UL 94V-0 rate flame retardant Terminals: Solderable per MIL-STD-202 method 208 Polarity: As marked on diode body Mounting position: Any Weight: 2.2 gram approximately .50(12.7)MIN Application .1(2.54) .548(13.93) .269(6.85) .045(1.15) .226(5.75) Pb Free Plating Product ® .025(0.65)MAX .1(2.54) Case Case Case Case Negative Positive * Doubler * Reverse Doubler Common Cathode Common Anode Tandem Polarity Tandem Polarity Prefix "F12C" Prefix "F12A" Available for Mass Production * MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25oC ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOL F12C20CT F12C40CT F12C60CT UNIT F12A20CT F12A40CT F12A60CT Maximum Recurrent Peak Reverse Voltage VRRM 200 400 600 V Maximum RMS Voltage VRMS 140 280 420 V Maximum DC Blocking Voltage VDC 200 400 600 V Maximum Average Forward Rectified o Current TC=100 C IF(AV) 12.0 A IFSM 100 A Peak Forward Surge Current, 8.3ms single Half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage @ 6.0 A VF 0.98 o Maximum DC Reverse Current @TJ=25 C o At Rated DC Blocking Voltage @TJ=125 C IR 1.3 uA 250 uA nS Trr 35 Typical junction Capacitance (Note 2) CJ 65 Operating Junction and Storage Temperature Range V 10.0 Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance (Note 3) 1.7 R JC 2.2 TJ, TSTG -55 to +150 pF o C/W o C NOTES : (1) Reverse recovery test conditions IF = 0.5A, IR = 1.0A, Irr = 0.25A. (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts DC. (3) Thermal Resistance junction to case. Rev.05 © 2006 Thinki Semiconductor Co.,Ltd. Page 1/2 http://www.thinkisemi.com/ F12A20CT thru F12A60CT ® FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1 - FORWARD CURRENT DERATING CURVE 100 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 12 10 7 5 2 60 Hz Resistive or Inductive load 0 Pulse Width 8.3ms Single Half-Sire-Wave (JEDEC Method) 80 60 40 20 0 0 50 100 150 1 CASE TEMPERATURE, C 100 FIG.4 - TYPICAL REVERSE CHARACTERISTICS FIG.3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1000 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES IINSTANTANEOUS FORWARD CURRENT, AMPERES 10 NUMBER OF CYCLES AT 60Hz o F12A20CT F12A40CT 6 F12A60CT o TJ=25 C PULSE WIDTH=300uS 1% DUTY CYCLE 0.1 0.2 0.4 0.6 0.8 1.0 1.2 1.4 o TJ=125 C 100 10 o TJ=25 C 1 0.1 0 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% FIG.5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 1000 o TJ = 25 C f = 1.0 MHZ Vsig = 50mVp-p 100 10 0.1 1.0 4.0 10 100 REVERSE VOLTAGE, VOLTS Rev.05 © 2006 Thinki Semiconductor Co.,Ltd. Page 2/2 http://www.thinkisemi.com/