FR151 thru FR157 - Thinki Semiconductor Co.,Ltd.

FR151 thru FR157
®
Pb
FR151 thru FR157
Pb Free Plating Product
FAST SWITCHING PLASTIC RECTIFIER DIODES
DO-15
Unit: inch(mm)
Features
•
1.0(25.4)MIN.
•
.034(.86)
1.5 ampere operation at TA=50o
C with no thermal runaway.
Low leakage.
.300(7.6)
•
High current capability.
Mechanical Data
Case: Molded plastic, DO-15
.140(3.6)
•
Terminals: Plated axial leads, solderable per
•
MIL-STD-202, method 208
•
Polarity: Color band denotes cathode
•
Mounting Position: Any
.104(2.6)
1.0(25.4)MIN.
•
.028(.71)
.230(5.8)
•
Absolute Maximum Ratings and Characteristics
Ratings at 25 OC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz. resistive or inductive
load. For capacitive load, derate current by 20%.
Symbols
FR151
FR152
FR153
FR154
FR155
FR156
FR157
Units
Maximum repetitive peak reverse voltage
VRRM
50
100
200
400
600
800
1000
V
Maximum RMS voltage
VRMS
35
70
140
280
420
560
700
V
Maximum DC blocking voltage
VDC
50
100
200
400
600
800
1000
V
Maximum average forward rectified current
375”(9.5mm) lead length at TA = 55 OC
I(AV)
1.5
A
IFSM
50
A
VF
1.3
V
Peak forward surge current IFM (surge)
8.3ms single half sine-wave superimposed
on rated load (JEDEC method)
Maximum forward voltage at 1.5A DC
Maximum reverse current
TJ = 25 OC
at rated DC blocking voltage
TJ = 100OC
Typical junction capacitance (Note 1)
Typical thermal resistance (Note 3)
Maximum reverse recovery time(Note 2)
Operating and storage temperature range
5
IR
500
CJ
25
RθJL
Trr
TJ ,TS
µA
pF
O
45
150
150
150
150
-55 to +150
250
500
500
C/W
ns
O
C
Notes:
(1) Measured at 1MHZ and applied reverse voltage of 4 VDC.
(2) Reverse recovery test conditions: IF = 0.5A, IR = 1.0A, Irr = 0.25A.
(3) Thermal resistance from junction to ambient and from junction to lead at 0.375”(9.5mm) lead length P.C.B
mounted.
Rev.04
© 2006 Thinki Semiconductor Co.,Ltd.
Page 1/2
http://www.thinkisemi.com/
FR151 thru FR157
®
FIG.2- TYPICAL REVERSE CHARACTERISTICS
PER LEG
1000
1.50
1.25
INSTANTANEOUS REVERSE CURRENT. ( A)
AVERAGE FORWARD CURRENT AMPERES
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
1.00
.75
.25
0
60
PEAK FORWARD SURGE CURRENT. (A)
Single Phase
Half Wave 60Hz
Resistive or
Inductive Load
0.375"(9.5mm)
Lead Length
.50
0
25
50
75
100
125
o
AMBIENT TEMPERATURE. ( C)
150
175
FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
100
Tj=125 0C
10
Tj=75 0C
1
Tj=25 0C
0.1
50
0
Tj=55 0C
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
40
30
20
FIG.5- TYPICAL FORWARD CHARACTERISTICS
10
10
0
JUNCTION CAPACITANCE.(pF)
100
2
4
6
8
10
20
NUMBER OF CYCLES AT 60Hz
40
60
80 100
INSTANTANEOUS FORWARD CURRENT. (A)
1
FIG.4- TYPICAL JUNCTION CAPACITANCE
8.3ms Single Half Sine Wave
JEDEC Method
Tj=25 0C
10
1.0
0.1
Tj=25 oC
Pulse Width=300 s
1% Duty Cycle
11
1
10
5
REVERSE VOLTAGE. (V)
50
.01
0.4
100
0.6
0.8
1.0
1.2
1.4
1.6
FORWARD VOLTAGE. (V)
FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
10W
NONINDUCTIVE
50W
NONINDUCTIVE
trr
+0.5A
(-)
DUT
(+)
50Vdc
(approx)
(-)
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
Rev.04
© 2006 Thinki Semiconductor Co.,Ltd.
0
-0.25A
(+)
-1.0A
1cm
SET TIME BASE FOR
5/ 10ns/ cm
Page 2/2
http://www.thinkisemi.com/